Poly Diallyldimethylammonium Chloride Research Articles

Self-healing and corrosion-sensing multifunctional coatings containing pH-sensitive TiO2-based composites

Polyelectrolyte-encapsulated nanocontainers can effectively respond to changes of pH and thus control the on-demand release of corrosion inhibitors. A pH-responsive release system (Phen-Tpp@MTNs-PDDA) was developed based on the cationic polyelectrolyte poly dimethyl diallyl ammonium chloride (PDDA) encapsulated mesoporous TiO2 nanocontainers (MTNs) loaded with 1,10-phenanthroline (Phen) and tripolyphosphate ions (Tpp) corrosion inhibitors. The epoxy coating (EP) embedded with Phen-Tpp@MTNs-PDDA (Phen-Tpp@MTNs-PDDA/EP) demonstrates superior self-healing properties and confers long-term protection on the metal substrate by the cooperative effect of Phen and Tpp. Simultaneously, this hybrid coating is endowed with corrosion sensing capability based on the color development originating from the interaction of Phen and carbon steel. This work shows excellent corrosion resistance to carbon steel, which also provides an effective strategy for the corrosion protection of metals.

Polymer Coatings Affect Transport and Remobilization of Colloidal Activated Carbon in Saturated Sand Columns: Implications for In Situ Groundwater Remediation.

Colloidal activated carbon (CAC) is an emerging technology for the in situ remediation of groundwater impacted by per- and polyfluoroalkyl substances (PFAS). In assessing the long-term effectiveness of a CAC barrier, it is crucial to evaluate the potential of emplaced CAC particles to be remobilized and migrate away from the sorptive barrier. We examine the effect of two polymer stabilizers, carboxymethyl cellulose (CMC) and polydiallyldimethylammonium chloride (PolyDM), on CAC deposition and remobilization in saturated sand columns. CMC-modified CAC showed high mobility in a wide ionic strength (IS) range from 0.1 to 100 mM, which is favorable for CAC delivery at a sufficient scale. Interestingly, the mobility of PolyDM-modified CAC was high at low IS (0.1 mM) but greatly reduced at high IS (100 mM). Notably, significant remobilization (release) of deposited CMC-CAC particles occurred upon the introduction of solution with low IS following deposition at high IS. In contrast, PolyDM-CAC did not undergo any remobilization following deposition due to its favorable interactions with the quartz sand. We further elucidated the CAC deposition and remobilization behaviors by analyzing colloid-collector interactions through the application of Derjaguin-Landau-Verwey-Overbeek theory, and the inclusion of a discrete representation of charge heterogeneity on the quartz sand surface. The classical colloid filtration theory was also employed to estimate the travel distance of CAC in saturated columns. Our results underscore the roles of polymer coatings and solution chemistry in CAC transport, providing valuable guidelines for the design of in situ CAC remediation with maximized delivery efficiency and barrier longevity.

Evaluation an anionic polyacrylamide flocculant with microblock structure in the hematite wastewater treatment: Characterization and flocculation performance

In this study, a template polymer with anionic microblock structure was successfully synthesized through ultrasonic initiated template copolymerization (USTP) by using sodium allylsulfonate (SAS) and acrylamide (AM) as monomers, poly diallyl dimethyl ammonium chloride (polyDADMAC) as template, and 2,2′-azobis [2-(2-imidazolin-2-yl) propane] dihydrochloride (VA-044) as initiator. The anionic polyacrylamide (APAM-T) flocculant was characterized by Fourier transform infrared spectroscopy (FTIR), 1H nuclear magnetic resonance spectroscopy (1H NMR), and scanning electron microscopy (SEM). Furthermore, the X-ray photoelectron spectroscopy (XPS) was conducted to measure the elemental composition. The results of XPS and 1H NMR spectroscopy analysis indicated the existence of anionic microblock structure in APAM-T. Besides, the copolymerization was revealed to follow the self-assembly mechanism by analyzing the association constant (KM). The flocculation performance was evaluated by turbidity and zeta potential in the flocculation tests. The results indicated that the APAM-T with microblock structure enhanced the charge neutralization and bridging adsorption capacity, thus improving the flocculation performance. In the floc particle size distribution and fragmentation and reflocculation experiments, the floc corresponding to APAM-T had the strongest regeneration ability after fragmentation, which further confirmed the criticality of the microblock structure in enhancing the flocculation performance. Compared with existing studies, this study not only demonstrated a novel synthesis method, but also found that the microblock structure could significantly improve its treatment efficiency and effectiveness, providing a new theoretical basis and practical application path for wastewater treatment technology.

An electrochemiluminescence sensor based on Ag NPs amplifying PDDA-modified TbPO4:Ce NWs signal for sensitive detection of lincomycin

The residue of lincomycin in water will not only aggravate the drug resistance of bacteria but also cause damage to the human body through biological accumulation. In this work, an electrochemiluminescence (ECL) aptasensor for the detection of lincomycin was constructed based on polydimethyldiallylammonium chloride (PDDA) functionalized Ce-doped TbPO4 nanowires (PDDA-TbPO4:Ce NWs) and silver nanoparticles (Ag NPs). TbPO4:Ce NWs were used as the luminophore, and PDDA was used to functionalize the luminophore to make the surface of the luminophore positively charged. The negatively charged silver nanoparticles were combined with PDDA-TbPO4:Ce NWs by electrostatic interaction. Ag NPs accelerated the electron transfer rate and promoted the ECL efficiency, which finally increased the ECL intensity of TbPO4:Ce NWs by about 4 times. Under the optimal conditions, the detection limit of the ECL sensor was as low as 4.37 × 10−16 M, and the linear range was 1 × 10 − 15 M to 1 × 10 − 5 M, with good selectivity, stability, and repeatability. The sensor can be applied to the detection of lincomycin in water, and the recovery rate is 97.7–103.4 %, which has broad application prospects.

Removal efficiency and mechanism of geosmin by modified micro-nano bubbles in drinking water treatment process

The problem of odor and taste caused by geosmin had been widely discussed globally. While existing water treatment processes were difficult to remove geosmin cleanly and efficiently, and the traditional aeration method of micro-nano bubbles (MNBs) led to low removal efficiency due to the low probability of collision between the bubbles and the contaminants. In this study, micro-nano bubble modification technique was used to improve the removal efficiency. Three surface modifiers, hexadecyl trimethyl ammonium bromide (CTAB), chitosan (CTS), and poly dimethyl diallyl ammonium chloride (PDADMAC), were selected for this study. The effects of the surface modifiers on the properties of MNBs and the effects of these changes on the removal efficiency of GSM were explored. The experimental results showed that when all three modifiers were dosed at 5 mg/L, the PDADMAC-modified MNBs had the best GSM removal effect of 70.9 %, while the Zeta potential of the effluent was lower at 4.17 mV, which had less influence on the downstream process, and was an ideal modifier. The contribution of various removal pathways to GSM removal was also explored through intermediate product analysis combined with variable control experiments. The experimental results showed that the enhanced removal of GSM was attributed to the enhanced capture of GSM by PDADMAC-modified MNBs and the enhanced oxidation of GSM by PDADMAC-modified MNBs. At the same time, the removal efficiency of this process in natural waters decreased by <5 % only. This study could provide data and theoretical support for the enhanced removal of olfactory compounds by modified MNBs for application in practical engineering.

Removal of Plastics from Micron Size to Nanoscale Using Wood Filter.

Plastic pollution, particularly microplastic (MP) and nanoplastic (NP) pollution, has become a significant concern. This study explores the use of porous wood for filtration to remove MPs and NPs and investigates their removal mechanisms. Undecorated fir wood with a thickness of 4 mm achieves a 91% removal rate for model polystyrene (PS) MPs (2.6 μm) at a water flux of 198 L/m2h. However, its separation performance for NPs (255.8 and 50.9 nm) is poor. It also shows that fir wood (coniferous wood) has a higher PS removal rate than poplar wood (hard wood). With poly dimethyl diallyl ammonium chloride (PDDA) modification, both MPs and NPs are effectively removed, with NPs' removal rate increasing from <10% to 90% for PDDA/wood. Characterization results reveal that size-exclusive interception dominates for micron-sized particles, and electrostatic interaction is crucial for nanosized particles. Additionally, intercepted NPs have been used as a strong binder for hot-pressed wood to remarkably enhance the mechanical properties of wood, suggesting a novel recycle utilization of discarded wood filters. Overall, this renewable wood material offers a simple solution for tackling MP/NP pollution.

Polyelectrolyte modified black phosphorus/titania nanosheet heterojunction enhanced photocatalysis: Synergistic enhancement effect of interface affinity and electron transport channel

The instability and high electron-hole recombination have limited the application of black phosphorus (BP) as an excellent photocatalyst. To address these challenges, poly dimethyl diallyl ammonium chloride (PDDA), poly (allylamine hydrochloride) (PAH), and polyethyleneimine (PEI) are introduced to the functionalization of BP (F-BP), which can not only enhance its stability, but also boost the carrier transfer. Furthermore, a high-performance heterojunction photocatalyst is fabricated using F-BP and titania nanosheets (TNs) via a layer-by-layer self-assembly approach. The experimental outcomes unequivocally indicate that F-BP exhibits fast charge migration compared to BP. The density functional theory (DFT), in situ Kelvin-probe force microscopy (KPFM) and other advanced characterization techniques collectively unfold that PDDA modified BP can notably boost separation and propagation of charges, along with an enhanced carrier abundance. In summary, this novel strategy of using polyelectrolytes to enhance the electron transfer and the stability of BP permits immense potential in building next-generation BP-based high efficiency photocatalysts.

A Novel Polymer Nanoparticle Polydimethyl Diallyl Ammonium Chloride as An Adjuvant Enhances the Immune Response of SARS-CoV-2 Subunit Vaccine.

The Coronavirus Disease 2019 (COVID-19) pandemic caused by SARS-CoV-2 has a significant impact on global health and the economy. It has underscored the urgent need for a stable, easily produced and effective vaccine. This study presents a novel approach using SARS-CoV-2 spike (S) protein-conjugated nanoparticles (NPs) in combination with cyclic GMP-AMP (cGAMP) (S-NPs-cGAMP) as a subunit vaccine. When mice are immunized, the antiserum of S-NPs-cGAMP group exhibits a 16-fold increase in neutralizing activity against a pseudovirus, compared to S protein group. Additionally, S-NPs-cGAMP induces even higher levels of neutralizing antibodies. Remarkably, the vaccine also triggers a robust humoral immune response, as evidenced by a notable elevation in virus-specific IgG and IgM antibodies. Furthermore, after 42 days of immunization, there is an observed increase in specific immune cell populations in the spleen. CD3+ CD4+ and CD3+ CD8+ T lymphocytes, as well as B220+ CD19+ and CD3- CD49b+ NK lymphocytes, show an upward trend, indicating a positive cellular immune response. Moreover, the S-NPs-cGAMP demonstrates promising results against the Delta strain and exhibits good cross-neutralization potential against other variants. These findings suggest that pDMDAAC NPs is potential adjuvant and could serve as a versatile platform for future vaccine development.

Membrane‐assisted capacitive deionization: Effect of Poly(vinyl alcohol) cross‐linking on the properties of ion exchange membranes

AbstractNovel composite electrodes were developed for application in membrane capacitive deionization (MCDI). Activated carbon (AC) was dispersed in a solution of poly(vinyl alcohol) (PVA) mixed with polyacrylic acid (PAA) or poly dimethyl diallyl ammonium chloride (PDMDAAC), and cast onto the surface of an AC‐based modified graphite electrode, prepared by phase inversion, to form a composite membrane further cross‐linked with glutaraldehyde (GA). The effect of the cross‐linking on the chemical structure of the PVA‐based membranes was determined by attenuated total reflectance Fourier‐transform infrared (ATR‐FTIR) spectroscopy. Cyclic voltammetry was conducted to examine the specific capacitance of the composite electrodes. Desalination experiments were then performed with MCDI unit cells to study the effect of cross‐linking on the desalination efficiency. It was proved that after optimization, the synthesized composite electrodes exhibited one and a half times higher NaCl removal capacity and three times higher adsorption rate as compared to that of a conventional CDI cell using commercial ion exchange membranes (IEMs) with almost the same energy consumption. The enhanced desalination performance was attributed to the optimized properties of the selected polymers and the improved adhesion of IEMs to the electrodes. This research paves the way for the application of new materials in MCDI processes for improved water desalination.

Sorption properties of pristine and functionalized magnetic carbon nanotubes in relation to double-stranded DNA

BackgroundOwing to improvement of the molecular diagnostic methods using purified preparations of nucleic acids (NAs), the development of effective methods providing the isolation of DNA is still relevant. The sorption properties of magnetic multi-walled carbon nanotubes (MWCNTs), oxidized MWCNTs and MWCNTs (pristine and oxidized) modified with polydiallyldimethylammonium chloride (pDADMAC) with respect to double strained DNA have been studied. ResultsIt was shown that in the presence of MWCNTs/pDADMAC particles the DNA molecules were reversibly retained by the particle’s surface. The optimal conditions for each step of DNA extraction from model solutions using the obtained material were selected. A comparative evaluation of the effectiveness of the proposed method for DNA isolation based on the results of spectrophotometry and real-time PCR was carried out. It was shown that the desorbed DNA was efficiently amplified in PCR, inhibition of polymerase did not occurred. Probable mechanisms of DNA retention due to the influence of residual impurities of catalysts in the MWCNT composition, as well as the surface charge of nanotubes are proposed. ConclusionSequentially oxidized and coated with pDADMAC magnetically susceptible CNTs are seemed to be a promising material for development of low-cost systems proving an easy isolation, storage, and subsequent use of dsDNA in molecular diagnostics. The sorption properties of such systems are determined with highly developed specific surface area and their chemical composition.

Combined impacts of aluminum and silica ions on RO membrane fouling in full-scale ultrapure water production facilities

In this study, a fouled reverse osmosis (RO) membrane from a full-scale ultrapure water (UPW) facility was autopsied and investigated to propose the fouling mechanism and mitigation strategies. Although the influent was introduced to the coagulation and ultrafiltration as the pre-treatment processes, thick fouling layers were found over the entire RO surface. The foulant was mainly composed of aluminum silicates due to the elevated Al concentration (up to 100 μg/L) originated from the coagulation process utilizing polyaluminum chloride, and high recovery (up to than 90%) of RO process. Lab-scale fouling tests also confirmed that the elevated Al concentration in the RO influent contributed to significant flux decline due to a bridging effect with negatively charged organic matter and the formation of aluminum silicates. The application of polydiallyldimethylammonium chloride as an alternative coagulant successfully mitigated the organic and silicate fouling. Therefore, control of the residual aluminum ions originated from the coagulation process is critical to mitigate both organic and inorganic fouling on RO membrane surfaces during the production of UPW.

Development of Composite Nanostructured Electrodes for Water Desalination via Membrane Capacitive Deionization.

Novel two-layer nanostructured electrodes are successfully prepared for their application in membrane capacitive deionization (MCDI) processes. Nanostructured carbonaceous materials such as graphene oxide (GO) and carbon nanotubes (CNTs), as well as activated carbon (AC) are dispersed in a solution of poly(vinyl alcohol) (PVA), mixed with polyacrylic acid (PAA) or polydimethyldiallylammonium chloride (PDMDAAC), and subsequently cast on the top surface of an AC-based modified graphite electrode to form a thin composite layer that is cross-linked with glutaraldehyde (GA). Cyclic voltammetry (CV) is performed to investigate the electrochemical properties of the composite electrodes and desalination experiments are conducted in batch mode using a MCDI unit cell to investigate the effects of i) the nanostructured carbonaceous material, ii) its concentration in the polymer blend, and iii) the molecular weight of the polymers on the desalination efficiency of the system. Comparative studies with commercial membranes are performed proving that the composite nanostructured electrodes are more efficient in salt removal. The improved performance of the composite electrodes is attributed to the ion exchange properties of the selected polymers and the increased specific capacitance of the nanostructured carbonaceous materials. This research paves the way for wider application of MCDI in water desalination.

Removal of algae from ballast water by cationic flocculant-composite titanium xerogel coagulant: Differences in freshwater and seawater

The treatment of ballast water has been garnering increasing attention, with planktonic algae removal being a crucial part. Coagulation has been demonstrated as an effective method for algae removal, albeit few coagulants exhibit excellent coagulation performance in both freshwater and seawater. To address this issue, the cationic flocculant poly dimethyl diallyl ammonium chloride (PDADMAC) was composited with titanium xerogel coagulant (TXC), abbreviated as PT. Using the algae Cyclotella meneghiniana as the research object, the algal removal performance and mechanisms of PT in freshwater and seawater were investigated. Cell integrity, superoxide dismutase (SOD) activity, and malondialdehyde (MDA) content of C. meneghiniana during floc storage were also evaluated. The PT composite coagulant exhibited excellent coagulation performance in both freshwater and seawater. Its algal removal ability was superior to TXC and the commercial coagulants polyaluminum chloride (PAC) and polymerized ferrous sulfate (PFS), with removal rates for C. meneghiniana reaching 98.3 % in freshwater and 98.4 % in seawater at a 80 mg/L dosage. PT also exhibited excellent removal performance over wide dosage and pH ranges. PT acted via distinct coagulation mechanisms in freshwater and seawater, with charge neutralization and bridging played major roles in freshwater and sweeping being important in seawater. The floc storage experiment indicated that the coagulation process did not directly lead to algal cell fragmentation, but PT accelerated and exacerbated oxidative stress and oxidative damage to algal cells during floc storage. Furthermore, PT also showed excellent removal performance for the marine diatom Skeletonema costatum and the freshwater cyanobacteria Cylindrospermopsis raciborskii. This work not only provides a novel approach for algae removal in ballast water, but also enhances our understanding of the coagulation behavior of titanium-based coagulants in different water environments.

Achievement of waste sludge deep dehydration under acidic conditions with polydimethyldiallylammonium chloride and ferric chloride: performance and mechanism.

The biological treatment of wastewater generates a substantial amount of waste sludge that requires dewatering before final disposal. Efficient sludge dewatering is essential to minimize storage and transportation costs. In this study, the sludge conditioners polydimethyldiallylammonium chloride (PDMDAAC) and ferric chloride (FeCl3) were sequentially dosed, and the pH was adjusted to 3. As a result, the sludge moisture content (MC) was reduced to 59.4%, achieving deep dewatering. After conditioning, the tightly bound extracellular polymeric substances (TB-EPS) were reduced from 34.5 to 10.2 mg g-1 VSS, with the majority of the reduced fractions being composed of protein (PN). In contrast, soluble EPS increased more than 8 times. Subsequent studies revealed that the decrease in PN from TB-EPS primarily involved tryptophan and tyrosine proteins, accompanied by a significant reduction in the N-H and C[double bond, length as m-dash]C absorption peaks. These results highlight the critical role of TB-EPS dissolution in achieving deep dehydration, with the N-H in PN was identified as the key group influencing sludge dewatering. Combined with the changes in sludge particle size and morphology, the dewatering mechanism can be summarized as follows: PDMDAAC dissolves TB-EPS, simultaneously disrupting the floc structure and refining the sludge. Subsequently, FeCl3 reconstructs these elements, forming larger particle sizes. Finally, hydrochloric acid reduces TB-EPS once again, releasing bound water. This study offers alternative methods and new insights for achieving deep dewatering of waste sludge.

Micron-Sized Hierarchical Beta Zeolites Templated by Mesoscale Cationic Polymers as Robust Catalysts for Acylation of Anisole with Acetic Anhydride

Hierarchical Beta zeolites with interconnected intracrystalline mesopores and high structural stability are highly attractive for catalytic applications involving bulky reactants. Here, by introducing a suitable amount of polydiallyldimethylammonium chloride into the initial synthesis system, micron-sized Beta zeolite crystals with abundant hierarchical porosity (Beta-H) were hydrothermally synthesized. The sample named Beta-H_1 exhibited very high catalytic activity and durability for the Friedel–Crafts acylation of anisole with acetic anhydride. A 92% conversion rate of acetic anhydride could be achieved after 1 h of reaction in a fixed bed reactor, and 71% conversion still remained after 10 h, much better than the rate for conventional Beta zeolite (which decreased rapidly from 85% to 37% within 10 h). The enhanced catalytic performance of Beta-H zeolites could be mainly attributed to the relatively lower strong acid density and the faster transport rate of the hierarchical zeolites. In addition, Beta-H showed high structural stability and could be easily regenerated via high-temperature calcination without obvious loss in catalytic activity, demonstrating its great potential for catalytic applications in the industrially important Friedel–Crafts acylation process.

Fabrication and Characterization of Zein/PDADMAC Nanoparticles to Encapsulate Tebuconazole by Antisolvent Precipitation Method**

AbstractIn order to improve the sustained release effect and antifungal activity of tebuconazole (TEB), zein /poly dimethyl diallyl ammonium chloride (PDADMAC) nanoparticles (NPs) were prepared in this study. The hollow zein NPs were made by anti‐solvent precipitation method in which sodium carbonate was chosen as sacrificial template, and PDADMAC was combined with zein NPs via electrostatic self‐assembly after loading TEB. The NPs were characterized through particle size, Zeta potential, scanning electron microscopy (SEM), sustained release effect, contact angle, encapsulation efficiency (EE), loading efficiency (LE) and antifungal activity. In this study, TEB/zein/PDADMAC NPs were stable for at least 28 days at room temperature. The release of TEB showed lower release in NPs compared with technical concentrate (TEB TC, 98 %). In addition, NPs also significantly influenced performance such as wetting performance and antifungal activity. The developed functional TEB/zein/PDADMAC NPs with excellent properties can be promising for antifungal pesticide applications.

СУДА ЕРИТІН ПОЛИМЕРЛЕР МЕН ОЛАРДЫҢ ПОЛИКОМПЛЕКСТЕРІНІҢ СУЛЫ ЕРІТІНДІДЕГІ ҚАСИЕТТЕРІ

Abstract. The interaction of oppositely charged polyelectrolytes (sodium salt of carboxymethylcellulose (NaCMC), methylcellulose (MC), polyethylenimine (PEI) and polydimethyldiallylammonium chloride (PDMDAAС), and unifloc (UF)) in an aqueous environment was studied using the methods of viscometry, spectrophotometry and macroelectrophoresis. It has been established that the interaction of these polyelectrolytes is accompanied by a significant decrease in reduced viscosity (up to 0.1-0.15 dl/g, which is typical for compacted macromolecules of globular proteins), an increase in optical density and an inversion of the sign of the electrokinetic potential. All this indicates the formation of interpolymer complexes from interacting cationic and anionic polyelectrolytes. Experimental results of studying the properties of water soluble polymers and their polyelectrolyte complexes in aqueous solutions at the water/air interface are described and discussed. It has been shown that complex formation in relatively simple systems is accompanied by changes in the pH of the medium, optical, hydrodynamic, electrochemical and other properties of macromolecules. In the systems we studied, the interaction of the system components is not accompanied by variations in the pH of the medium, therefore, information about the interaction of water-soluble polyelectrolytes in the systems we studied was obtained based on viscometric and spectrophotometric titration data, as well as from changes in the electrokinetic potential of macromolecules. The study of the electrokinetic potential showed that the formation of interpolymer complexes in the systems under consideration is accompanied by significant changes in the electrokinetic potential of macromolecules. A study of the properties of mixtures of aqueous solutions of Na-CMC, MC, UF with polydimethyldiallylammonium chloride and polyethylenimine indicates the formation of interpolyelectrolyte complexes that have a more compact structure than the original macromolecules. Key words: polyelectrolytes; flocculation; cross-linking; stability; interpolymer complexes; optical density; polymer.

Detection of emerging disinfection by-products by reversed-phase ion-pair chromatography electrospray-ionization mass spectrometry in drinking water

A sensitive and specific methodology that allows unequivocal identification of polydiallyldimethylammonium chloride (PDADMAC) disinfection by-product it monomer diallyldimethylammonium chloride (DADMAC) in drinking water samples based on reversed-phase ion-pair chromatography–electrospray ionization – mass spectrometry was optimized. Ion-pair reagent heptafluorobutyric (HFBA) was found to play a crucial role in the optimization of chromatographic parameters. The chromatographic retention time was optimized by varying concentrations of ion-pair reagent, flow rate, and column temperature to enable good chromatographic retention and sensitivity of disinfection by-product of interest DADMAC in positive electrospray ionization and using selected ion monitoring (SIM) mode. The method was validated and showed good linear regression of 0.99 and a detection limit of 0.008 mg L−1. The developed method was applied in a drinking water treatment plant operated by Mgeni Water in Durban, South Africa, to detect trace levels of the disinfection by-product of interest (DADMAC) at various points of the treatment process. The concentration of DADMAC in the water treatment plant ranged from not detected up to 0.65 mg L−1. In addition, this work through mass spectrometry provides the first evidence of ion-pairing (465 m/z peak) between DADMAC and the reagent, which is a confirmation of online derivatization. Also, the use of ion-pair prevented dimerization of DADMAC (286 m/z peak) inside the ionization chamber leading to high sensitivity.

Synergistic enhancement of coal slurry water sedimentation and dehydration process using PDMDAAC/PAM

Currently, most coal processing plants use a single pharmaceutical system with large dosage and poor sedimentation effect, resulting in poor subsequent dehydration effect. In this study, poly dimethyl diallyl ammonium chloride (PDMDAAC) as coagulant, and polyacrylamide (PAM) as flocculant, were used for synergistic enhancement of the coal slurry water sedimentation and dehydration process. The best pharmaceutical system was determined by integrating the evaluation indexes in the sedimentation and dehydration process. The mechanism of synergistic enhancement of coal slurry water sedimentation and dehydration process using PDMDAAC/PAM was revealed by analyzing zeta potential, SEM, XPS and FTIR spectroscopy results. Moreover, the Box–Behnken response surface methodology was used to determine the order of significance of coagulant dosage (Cc), flocculant dosage (Cm), and coal slurry water concentration (Cs) on the combined sedimentation and dehydration indexes, and Cm > Cs > Cc. Further, the correlation models between the combined sedimentation and dehydration indexes and each factor were established, the pharmaceutical system was further optimized, and model accuracy was verified. The optimal dosage of PDMDAAC10040 was 2.96 mg/L, and that of PAM2610 was 2.31 mg/L. Then, the industrial trials were conducted at the Tara Trench coal processing plant. Interestingly, after replacing the chemical regime, the efficiency of the thickener and filter press has been significantly improved, resulting in a 33.33% reduction in cost. This research can provide significant theoretical guidance and technical support for industrial applications.

Ag2O-Containing Biocidal Interpolyelectrolyte Complexes on Glass Surfaces-Adhesive Properties of the Coatings.

Biocidal coatings are of great interest to the healthcare system. In this work, the biocidal activity of coatings based on a complex biocide containing polymer and inorganic active antibacterial components was studied. Silver oxide was distributed in a matrix of a positively charged interpolyelectrolyte complex (IPEC) of polydiallyldimethylammonium chloride (PDADMAC) and sodium polystyrene sulfonate (PSS) using ultrasonic dispersion, forming nanoparticles with an average size of 5-6 nm. The formed nanoparticles in the matrix are not subject to agglomeration and changes in morphology during storage. It was found that the inclusion of silver oxide in a positively charged IPEC allows a more than 4-fold increase in the effectiveness of the complex biocide against E. coli K12 in comparison with the biocidal effect of PDADMAC and IPEC. Polycation, IPEC, and the IPEC/Ag2O ternary complex form coatings on the glass surface due to electrostatic adsorption. Adhesive and cohesive forces in the resulting coatings were studied with micron-scale coatings using dynamometry. It was found that the stability of the coating is determined primarily by adhesive interactions. At the macro level, it is not possible to reliably identify the role of IPEC formation in adhesion. On the other hand, use of the optical tweezers method makes it possible to analyze macromolecules at the submicron scale and to evaluate the multiple increase in adhesive forces when forming a coating from IPEC compared to coatings from PDADMAC. Thus, the application of ternary IPEC/Ag2O complexes makes it possible to obtain coatings with increased antibacterial action and improved adhesive characteristics.