Mesh Size Research Articles

Trade-off between drag and catch performance when designing zooplankton trawls

The aquaculture sector is in pursuit of sustainable and cost-effective raw materials for feed, and the copepod Calanus finmarchicus is a marine zooplankton species of commercial interest because of its high abundance in northern areas. These copepods have the potential to meet the demand for vast quantities of marine raw materials. However, the lack of an energy- and catch-efficient trawl technology has limited the development of this fishery. Therefore, this study investigated the effect of two central trawl net design parameters mesh size and taper angle to identify which values that provide optimal trade-off balance between gear drag and catch efficiency. We conducted flume tank experiments using a series of plankton nets varying in mesh size (250–1000 μm), solidity ratio (0.54–0.76), and taper angle (5°– 30°) to acquire data on gear drag. The same nets were then used in fishing trials to obtain data on their catch performance. This study shows that zooplankton nets with a mesh size of approximately 500 μm and a low taper angle of about 5° provided the best trade-off between drag and catch performance.

Dust dynamics: distribution patterns of semi-volatile organic chemicals across particle sizes in varied indoor microenvironments.

An extensive analysis of the distribution patterns of three distinct classes of semi-volatile organic chemicals (SVOCs)-phthalates (PAEs), organophosphate flame retardants (OPFRs), and polycyclic aromatic hydrocarbons (PAHs)-across four distinct size fractions of dust (25, 50, 100, and 200μm) was conducted. The dust samples were sourced from AC filter, covered car parking lots, households, hotels, mosques, and car floors. To generate the four fractions, ten dust samples from each microenvironment were pooled and sieved utilizing sieving apparatus with the appropriate mesh size. Selected SVOCs were quantified utilizing gas chromatography-mass spectrometry in electron impact (EI) mode. Results unveiled diverse contamination levels among dust fractions, showcasing car parking lot dust with the lowest chemical contamination, while car floor dust displayed the highest levels of PAHs and OPFRs, peaking at 28.3µg/g and 43.2µg/g, respectively. In contrast, mosque and household floor dust exhibited the highest concentrations of phthalates, with values of 985µg/g and 846µg/g, respectively. Across the analyzed microenvironments, we observed a trend where concentrations of SVOCs tended to rise as dust particles decreased in size, forming a visually striking pattern. This phenomenon was particularly pronounced in dust samples collected from car floors and parking lots. Among SVOCs, PAEs emerged as the predominant contributors with > 90% followed by OPFRs and PAHs. The high levels of OPFRs in car floor dust align logically with the fact that numerous interior components of cars are treated with OPFRs, within a compact indoor microenvironment, to comply to fire safety regulations. Furthermore, petroleum products are a major source of PAHs in the environment and all the sampled cars in the study had combustion engines. Consequently, car dust is more likely to be polluted with PAHs stemming from petroleum combustion. Although previous investigations have noted an increase in heavy metals and brominated flame retardants with decreasing dust particles, this is the first study analyzing these SVOCs in different fractions of dust from various microenvironments. However, aside from two specific microenvironments, the observed pattern of escalating SVOC concentrations with smaller dust particle sizes was not corroborated among the examined microenvironments. This divergence in concentration trends suggests the potential involvement of supplementary variables in influencing SVOC distributions within dust particles.

Improving the mechanical performance of railway concrete sleepers using recycled materials: An experimental and numerical study

This paper explores the use of three waste materials available in vast quantities, including waste tires, glass bottles and bamboo furniture, in the manufacture of railway sleepers. Mechanical properties of recycled concrete have been studied to establish an optimal mix suitable for concrete railway sleeper manufacturing. Thus, 5%, 10%, 15% and 20% recycled rubber sands (RRS) by volume of fine aggregate are used instead of 30# and 60# mesh sizes of fine aggregate. Moreover, 20%, 40%, 60%, 80% and 100% of aggregate volume are replaced by recycled glass aggregate (RGA) particles. Furthermore, different percentages of recycled bamboo fibers (RBF) have been used as 1%, 2% and 3% by volume of concrete. According to the optimal concrete mixtures of RRS, RGA and RBF, twelve concrete railway sleepers are manufactured and tested for middle and rail seat bending strengths. Results show that ref. sleeper has almost 16% and 24% lower strengths than RGA sleeper in middle and rail seat, respectively, while ref. sleeper have higher strengths by 16% and 13%, and 18% and 7% than RRS sleeper (M60-R5) and RBF sleeper (B2) in middle and rail seat, respectively. The FEM results show that the ([Formula: see text]) of the RGA sleeper is the minimum ratio by 1.11 and 1.13 for rail seat and middle of sleeper, respectively, which is the best performance. In RBF sleeper FEM model, Bamboo fiber can only bear 5% and 8% of total stress in middle and rail seat, respectively, due to low mechanical properties of fibers.

Development of a fast-running method for prediction of blast propagation in partially confined spaces

In this contribution, a series of findings from Computational Fluid Dynamics (CFD) simulations of blast propagation within fully confined spaces are presented. These numerical works have been carried out as part of an ongoing in-house development towards a fast-running method to predict overpressures and impulses arising from detonations within the various configurations of carparks in Singapore. In land-scarce cities like Singapore, carparks are typically located within the same structural footprints and are integrated with other functions of the building to facilitate convenient access. Design of carparks are required to meet statutory provisions with regards to the layout, headroom clearance and safety. To this end, the present research study has adopted a three-stage approach. First, different representative configurations of carparks are determined by making reference to and rationalising based on the prevailing statutory provisions in Singapore. This is then followed by a series of parametric CFD simulations to obtain essential numerical data in order to characterise the blast propagation within the respective partially confined spaces. Finally, several regression models are employed to derive relationships between the critical parameters and the blast data, with the aim of achieving a fast-running predictive method. This paper seeks to provide detailed descriptions of the first and the second stages, as well as to present the comparisons of numerically converged solutions, which are obtained from preliminary CFD simulations using two mesh sizes, against semi-analytical solutions which are calculated based on guidance from UFC 3-340-02 for fully confined detonation as initial reference cases.

A scale model study of an engine test facility for alleviating low-frequency howl

A scale model experimental study is conducted addressing howl occurring during engine tests in the Propulsion Systems Laboratory (PSL) of NASA Glenn Research Center. The aim is to understand the sources of the howling noise and find possible remedies. It is shown that a jet discharged into the model of the PSL entrance duct gives rise to high levels of low frequency noise. This occurs apparently due to duct acoustic modes randomly excited by the jet. Wire-mesh screens of various mesh size and configuration as well as tabs, placed at the end of the model duct, are shown to affect the noise. Comparative effects of these configurations are studied, and some are found to alleviate the low-frequency noise significantly. Based on these results, the equivalent of a 4-mesh screen is recommended as the end treatment for the duct of the PSL facility.

The effect of doping sulphhydryl-functionalised silica with different diameters on the electro-optical properties of PDLC

ABSTRACT In this study, we synthesised two kinds of spherical SiO2-SH particles with uniform and non-uniform morphologies, and investigated their effects on the electro-optical properties of PDLC. Compared with uniform SiO2-SH nanoparticles, we found that the samples doped with non-uniform SiO2-SH regulate the electro-optical properties of PDLC better. The electro-optical properties test results demonstrated that doping a small amount of SiO2-SH with different sizes significantly reduced the driving voltage of PDLC and maintained a high contrast ratio. SEM results indicated that the size of the polymer meshes was broadened with increasing SiO2-SH doping. This phenomenon can be attributed to the larger specific surface area and higher concentration of sulphhydryl groups in SiO2-SH particles of different sizes. These characteristics enable SiO2-SH to better react with acrylate monomers, thereby improving modulation effects on the electro-optical properties of PDLC. However, when the doping amount exceeded a certain value, the driving voltage of PDLC began to rise, and its electro-optical properties deteriorated because of the agglomeration of nanoparticles at higher doping levels. This study demonstrated that doping SiO2-SH particles of different sizes can optimise the properties of PDLC, which provided new ideas and directions for doping PDLC with nanomaterials.

Comparison of two hydrodynamic models for their rain-on-grid technique to simulate flash floods in steep catchment

In this study, two hydrodynamic models, TELEMAC-2D and HEC-RAS 2D, were compared for their Rain-on-Grid (RoG) technique with a particular focus on runoff generation processes in a small and steep catchment. Curve number (CN) method was applied in both the models to simulate two single storm events up to 20 h of duration, whereas the Green-Ampt Redistribution (GAR) method was additionally applied in HEC-RAS 2D for a multi-peak flood event with sustained flow between the peaks. CN and GAR methods were compared for this flood event, and a sensitivity analysis of the GAR parameters was also done. Moreover, the two models were compared for their calibration process, computational time, mesh size and shape, and model availability, in general, as well as the results including inundated areas, water depth, and velocity. The results indicate that both the models are capable of reproducing short duration single storm floods. NSE and R2 for both models ranged from 0.70 to 0.90 and from 0.93 to 0.95. However, the models struggled to reproduce the long- duration multi-peak flood event. The sensitivity analysis showed that the results are not very sensitive to the two GAR parameters which are responsible to influence the flow of the second peak in the flood event. Neither the CN nor the GAR infiltration method successfully replicated such events because the hydraulic models permanently lose infiltrated water from the domain. The returned sub-surface flow significantly contributes to river flow during these flood events; however, none of the model incorporates a return flow algorithm.

Machining Performance Analysis of Ti6-Al-4V in Powder-Mixed EDM Using Green Dielectric Oil

In this investigation, the factors were oil type ([Formula: see text]), powder type ([Formula: see text]), and powder concentration ([Formula: see text]) level, and the machining parameters were the voltage (V), capacitance (pf), pulse-on time ([Formula: see text]), and pulse-off time ([Formula: see text]). The output parameters were the material removal rate (MRR), and tool wear rate (TWR). Three types of oils and powders, along with their respective particle concentrations, were selected for this experiment. Neem, Karanja, and sesame oils were mixed with aluminum oxide (Al2O3), chromium (Cr), and nickel (Ni) powder at 4, 6, and 8[Formula: see text]gm/l, respectively, using an overhead stirrer to investigate the conditions under which the green oil powder mixed mixture yielded a higher MRR and lower TWR during the micro-EDM process of titanium alloy (Ti-6Al-4V) using a 0.8[Formula: see text]mm tungsten carbide (WC) tool with fixed machining parameters (240[Formula: see text]V, 100[Formula: see text]pf, 20[Formula: see text][Formula: see text]s [Formula: see text], and 5[Formula: see text][Formula: see text]s [Formula: see text]). All the powders used in this experiment had a 32-micron (450 mesh) size. The Taguchi L[Formula: see text] orthogonal array and grey relational analysis methods were used to design and optimize the input process parameters for both responses. SEM, optical microscopic analysis, and EDS analysis were performed to examine the surface morphology, characteristics of the WC tool, and elemental composition of both the tool and the workpiece material. The optimum conditions for Karanja oil with a Cr powder mixture concentration of 4[Formula: see text]g/l resulted in higher MRR and lower TWR. However, machining with neem and sesame oils resulted in higher TWR and lower MRR.

An efficient finite element mesh generation methodology based on μCT images of multi-layer woven composites

High-fidelity models are essential for accurate finite element (FE) simulations of composite material behavior. This paper proposes an efficient meshing methodology based on micro-Computed Tomography (μCT) images. U-Net convolutional neural network was used for image segmentation. Connected yarns were then separated using an improved procedure based on watershed algorithm and geometric transformations. The proposed Constrained Delaunay-Advancing Front Technique (CD-AFT) surface reconstruction algorithm extracts point cloud of yarns from segmented images and outputs high-quality and smooth orientable manifold watertight triangulated surface. Intersecting meshes of yarns are separated through node position detection and Laplacian moving. Experimental results show that proposed methodology is capable of accomplishing mesh generation for different mesh sizes. Compared with commercial software, it has obvious advantages in mesh quality and size control. Since the proposed method operates independently of commercial software and manual operation, it facilitates the automated generation of numerous high-fidelity models from μCT images for FE simulations.

Dielectric And Mechanical Properties Of PLA-Carbon Composites

This study focuses on the development and characterization of Carbon-based Polylactide (PLA) composites for 3D printer filaments. The aim is to enhance the electrical and mechanical properties of PLA by incorporating recovered carbon black (RCB) in different mesh sizes (500, 1000, 1500, and 2000 mesh). Electrical impedance spectroscopy and dielectric constant measurements were performed to investigate the electrical properties of the composites. Results showed that the addition of RCB increased the dielectric constant, with values ranging from 2.5 to 7.1, indicating improved electrical performance. Scanning electron microscopy (SEM) analysis revealed the dispersion of carbon particles within the composites, enhancing their electrical conductivity. The effect of RCB particle size on electrical properties was also explored, with smaller particle sizes (2000 mesh) resulting in the highest conductivity of 6.2 S/m. Tensile testing demonstrated that the addition of RCB increases the tensile strength of PLA, with values ranging from 28.6 MPa to 47.2 MPa, and the elastic modulus, ranging from 832 MPa to 1.56 GPa, depending on the mesh size. The optimal combination of RCB content and mesh size resulted in a composite with a tensile strength of 43.8 MPa. Overall, this research provides insights into the development of Carbon-based PLA composites with improved electrical and mechanical properties.

Land-use effects on leaf-litter breakdown in streams in a tropical lowland catchment

The expansion of oil palm and cattle grazing in the tropics continues to alter numerous ecosystem functions. The generated land-use change is potentially impacting stream leaf-litter breakdown, a fundamental process for freshwater ecosystems. To assess the effect of land-use change, we studied breakdown rates of forest (Pachira aquatica, Pouroma aspera, Sloanea ampla, and Hippocratea volubilis) and oil palm (Elaeis guineensis) leaves after a 26-day immersion in streams surrounded by rainforests, grazing lands, or oil palm plantations with and without riparian buffers. In addition, we assessed breakdown drivers by deploying litter bags (248) of two mesh sizes (15 mm and 0.5 mm) allowing or restricting macroinvertebrates’ access (134 coarse-mesh bags and 114 fine-mesh bags). Forest leaf breakdown by microbes (fine-mesh) was lower by 55% in the plantations compared to forests; while microbial oil palm-leaf breakdown was lower by 32% in the unbuffered plantations compared to forests (p < 0.05). Total litter breakdown was lower (p > 0.05) in the plantations but not when these preserved riparian buffers. Litter breakdown was driven primarily by microbes in all land uses except in the buffered plantations, possibly due to increased shredder biomass. These results suggest that oil palm agriculture may decrease microbial stream leaf-litter breakdown, especially in streams with no riparian buffers.

Novel Resin-Coated Sand Placement Design Guidelines for Controlling Proppant Flowback Post-Slickwater Hydraulic Fracturing Treatments

Summary Resin-coated sand (RCS) is an effective way for controlling post-stimulation proppant flowback. However, with the shift to slickwater treatment fluids, the “tail-in” placement approach has proved to be less efficient for complete flowback control due to the proppant settling characteristics of using low-viscosity fluids. A new RCS placement approach was developed based on the results of several flowback studies. Trial wells were completed in different US basins with successful results. Proppant flowback samples were collected during different stages of drillout and production from wells using slickwater fluid systems. Thirty-five wells, completed by thirteen different operators, within the Permian and MidCon basins were evaluated. All wells were completed using multiple proppant mesh sizes. A total of 375 flowback samples were collected during the drillout and production phases. The samples were sieved, and the results were fed into an in-house material balance model to determine the percentages of different mesh sizes in the flowback samples. The conclusions were used as guidelines for a new placement approach implemented in multiple new wells to control proppant flowback. The flowback samples ranged from predominantly lead proppant to a similar proportion of the pumped mesh sizes. Not one of the 35 wells had flowback samples containing the majority tail-in mesh size. This supports the early sand dune assumption, suggesting that the early proppant forms dunes near the wellbore and late sand settles over the existing proppant beds. The use of late RCS appears to have a minimal effect on preventing flowback of the early proppant within a stage utilizing slickwater fracturing. Therefore, RCS efficiency to control proppant flowback with the tail-in method is reduced when used in such slickwater stimulations. To seal the different proppant beds, the new approach recommends pumping multiple RCS steps within a stage. The first RCS step is recommended within the first 10–20%, the second sequence within the first 40–60% of proppant volume, and the third as a tail-in. The exact percentages and step design were based on the results of flowback samples from neighboring wells. The implementation of this approach in more than 30 wells resulted in superior flowback control compared to offset control wells. In all trials, the proppant flowback completely stopped within 1 to 7 days of starting production. In this paper, we discuss the drawbacks of the current RCS placement practice while suggesting a new practical approach supported by data. RCS tail-in showed successful flowback control with viscous fracturing fluids and hybrid systems. For slickwater systems, an optimized placement design for RCS throughout the pump schedule provided enhanced flowback control compared to RCS tail-in. Finally, we illustrate the results of field trials in which utilizing the new RCS placement approach successfully reduced flowback.

Effect of basket mesh size on the hydrodynamics of a partially filled (500 mL) USP rotating basket dissolution testing apparatus 1

The USP Rotating Basket Dissolution Testing Apparatus 1 is listed in the USP as one of the tools to assess dissolution of oral solid dosage forms. Baskets of different mesh sizes can be used to differentiate between dissolution profiles of different formulations. Here, we used Particle Image Velocimetry (PIV) to study the hydrodynamics of the USP Apparatus 1 using baskets with different mesh openings (10-, 20- and 40-mesh) revolving at 100 rpm, when the vessel was filled with 500 mL. The velocity profiles throughout the liquid were found to vary significantly using baskets of different mesh sizes, typically increasing with increased size of the opening of the basket mesh, especially for axial and radial velocities. This, in turn, resulted in a significantly different flow rate through the basket, which can be expected to significantly impact the dissolution rate of the drug product. A comparison between the results of this work with those of a previous study with a 900-mL fill volume (Sirasitthichoke et al., Intern. J. Pharmaceutics, 2021, 607: 120976), shows that although the hydrodynamics in the USP Apparatus 1 changed with fill level in the vessel, the flow rate through the basket was not significantly affected. This implies that tablets dissolving in the two systems would experience similar tablet-liquid medium mass transfer coefficients, and therefore similar initial dissolution rates, but different dissolution profiles because of the difference in volume

Effects of Soil Foundation and Mesh Size on Rubble Mound Breakwater Stability under Seismic Loading

Effects of Soil Foundation and Mesh Size on Rubble Mound Breakwater Stability under Seismic Loading

Catch Composition and Selectivity Drift Gillnet in Pambang Pesisir Village Bantan Subdistrict Bengkalis Regency

Gill nets are placed perpendicular to the water to block the swimming direction of the fish. Fish are caught by being entangled in the meshes or entangled (spun) in the body of the net. This research was conducted in Pambang Pesisir Village, Bantan District, Bengkalis Regency, to know the composition of the catch and the selectivity of drift gill nets, comparing the composition of the number, type, weight, and size of the catch from different mesh sizes, and knowing how to catch fish (entangled, gilled, snagged, wedged) on the same mesh used. This research was carried out in December 2020 using the experimental fishing method, which is a research method that uses samples of research objects caught on fishing gear for observation. The research results of drift gill nets are species-selective fishing gear. Moreover, drift gill nets with a mesh size of 7.62 cm are more selective than nets of 5.72 cm because they have a catch ratio value closer to 1 and catch more large fish (worth catching). How to catch fish with a mesh size of 5.72 cm, many fish were caught by snagged; namely, 65 fish (30%), wedged 61 fish (28%), gilled 59 fish (27%), and 33 fish entangled (15%). Meanwhile, for the mesh size of 7.62 cm, 30 fish (31%) were caught wedged, 27 fish (29%) snagged, 27 fish (29%) gilled, and ten fish entangled (11%).

Is mesh pore size in polypropylene meshes associated with the outcome in Lichtenstein inguinal hernia repair: a registry-based analysis of 22,141 patients.

Experimental data show that large-pored meshes reduce foreign body reaction, inflammation and scar bridging and thus improve mesh integration. However, clinical data on the effect of mesh porosity on the outcome of hernioplasty are limited. This study investigated the relation of pore size in polypropylene meshes to the outcome of Lichtenstein inguinal hernioplasty using data from the Herniamed registry. This analysis of data from the Herniamed registry evaluated perioperative and 1-year follow-up outcomes in patients undergoing elective, primary, unilateral Lichtenstein inguinal hernia repair using polypropylene meshes. Patients operated with a non-polypropylene mesh or a polypropylene mesh with absorbable components were excluded. Polypropylene meshes with a pore size of 1.0×1.0mm or less were defined as small-pored meshes, while a pore size of more than 1.0×1.0mm was considered large-pored. Unadjusted analyses and multivariable analyses were performed to investigate the relation of pore size of polypropylene meshes, patient and surgical characteristics to the outcome parameters. Data from 22,141 patients were analyzed, of which 6853 (31%) were operated on with a small-pore polypropylene mesh and 15,288 (69%) with a large-pore polypropylene mesh. No association of mesh pore size with intraoperative, general or postoperative complications, recurrence rate or pain requiring treatment was found at 1-year follow-up. A lower risk of complication-related reoperation tended to be associated with small-pore size (p=0.086). Furthermore, small-pore mesh repair was associated with a lower risk of pain at rest and pain on exertion at 1-year follow-up. The present study could not demonstrate an advantage of large-pore polypropylene meshes for the outcome of Lichtenstein inguinal hernioplasty.

Mesoscopic simulation of uniaxial compression fracture of concrete via the nonlocal macro-meso-scale consistent damage model

To capture the uniaxial compression fracture of concrete composite is still a great challenging problem. To this end, the newly proposed nonlocal macro-meso-scale consistent damage (NMMD) model is extended to simulate uniaxial compression fracture of concrete composites. In the NMMD model, a mesoscopic structure composed of material point pairs is attached to each material point. A decomposition scheme suitable for masonry-like materials is adopted to decompose the elongation quantity of point pairs. The topologic damage is defined as the weighted summation of mesoscopic damage in neighboring material point pairs driven by the decomposed elongation quantity. The physically-based energetic degradation function is employed to bridge the geometric discontinuity in solids and the energy dissipation, and thus the topologic damage is integrated into the framework of continuum damage mechanics. The Monte-Carlo method and two-phase random field model are employed to generate stochastic circular and irregular aggregates representing the meso structure of concrete, respectively. The interface transition zone is prescribed by reducing the critical value of interface point pairs. Numerical results indicate that both the crack patterns and stress–strain curves of the uniaxial compression experiments on concrete panels can be well captured by the proposed NMMD model without mesh size sensitivity. The influence of horizontal constraints on the top and bottom surfaces is investigated and shown to have an effect on the crack patterns, strength and deformation capability of the specimen. The necessity of decomposition is also illustrated.

Impact of several coarse-graining models on a pilot-scale fluidized bed behavior using discrete element method–computational fluid dynamics

Impact of several coarse-graining models on a pilot-scale fluidized bed behavior using discrete element method–computational fluid dynamics

Galerkin approximation for multi-term time-fractional differential equations

Fractional differential equations (FDEs) are utilized as a precise model for describing a wide range of biological and physical processes, benefiting from the inherent symmetry feature in natural phenomena. The introduction of multi-term time-fractional order equations serves to tackle intricate phenomena spanning various physical domains. This study solves multi-term time-fractional DEs using the quadratic B-spline Galerkin method. In Galerkin approach, the quadratic B-spline is utilized as both a test and a basis function. The fractional portion of time is evaluated using the Caputo definition. In addition, the Gauss quadrature formula is used to evaluate the integration of complex function which enhance the accuracy. Lax-Richtmyer's stability criterion is employed to evaluate the stability of the proposed scheme. The E2 and E∞ norms are computed and displayed in the tables to illustrate the robustness and efficiency of the method. We compute simulation for various nodal points as well as various mesh sizes to analyze the solution behavior. The obtained results are compared with the exact and available results, indicating that the proposed scheme is more efficient. The graphical solution of each example is also demonstrated which verifies that exact and approximate solutions graphs closed with each other.

Microplastics Removal Efficiency and Risk Analysis of Wastewater Treatment Plants in Oman

Microplastics (MPs) have recently been documented as an emerging pollutant that poses a critical threat to environment. Wastewater treatment plants (WWTPs) are commonly regarded as significant contributors to the presence of MPs. This study aimed to assess the MPs load of three wastewater treatment facilities in Oman using various treatments, including MBR, SBR, and CAS. Wastewater samples from influent, effluent, and sludge were collected and analyzed to determine the concentration, morphology, size, color, and polymer type of the MPs. A set of sieves with a mesh size range of 1 mm to 45 μm was used to for filteration. Oxidation treatment was applied for all samples using Fenton's reagent, followed by density separation by sodium chloride solution. The Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR- FTIR) method was utilized to test 10% from each sampling point to confirm the polymer types of the MPs. The pollution load index (PLI) and hazard index (HI) have been employed to assess the risk associated with the chemical toxicity and concentration of detected particles. The PROMETHEE method was used to rank the risk of sampling sites based on different criteria that posed potential ecological and human health risks. The results indicate that the average concentrations of 0.99 MPs/L, 1.38 MPs/L, and 0.93 MPs/L were detected in the final treated effluent of WWTP A, WWTP B, and WWTP C, respectively. These concentrations correspond to overall removal efficiencies of 82.5%, 77.4%, and 79.2% for WWTP A, WWTP B, and WWTP C, respectively Most MPs found in tertiary effluent were smaller particles (425μm) and fiber-shaped. The major types of MPs were polypropylene (PP), low-density polyethylene (LDPE), polyurethane (PU), polyethylene terephthalate (PET), and Polyvinyl chloride (PVC). This study showed that treated effluent and sludge release significant MPs into the environment.