Different Degrees Of Polymerization Research Articles

A-type proanthocyanidins: Sources, structure, bioactivity, processing, nutrition, and potential applications.

A-type proanthocyanidins (PAs) are a subgroup of PAs that differ from B-type PAs by the presence of an ether bond between two consecutive constitutive units. This additional C-O-C bond gives them a more stable and hydrophobic character. They are of increasing interest due to their potential multiple nutritional effects with low toxicity in food processing and supplement development. They have been identified in several plants. However, the role of A-type PAs, especially their complex polymeric form (degree of polymerization and linkage), has not been specifically discussed and explored. Therefore, recent advances in the physicochemical and structural changes of A-type PAs and their functional properties during extraction, processing, and storing are evaluated. In addition, discussions on the sources, structures, bioactivities, potential applications in the food industry, and future research trends of their derivatives are highlighted. Litchis, cranberries, avocados, and persimmons are all favorable plant sources. Α-type PAs contribute directly or indirectly to human nutrition via the regulation of different degrees of polymerization and bonding types. Thermal processing could have a negative impact on the amount and structure of A-type PAs in the food matrix. More attention should be focused on nonthermal technologies that could better preserve their architecture and structure. The diversity and complexity of these compounds, as well as the difficulty in isolating and purifying natural A-type PAs, remain obstacles to their further applications. A-type PAs have received widespread acceptance and attention in the food industry but have not yet achieved their maximum potential for the future of food. Further research and development are therefore needed.

Inulin with different degrees of polymerization as a functional ingredient: Evaluation of flour, dough, and steamed bread characteristics during freezing

In the study, the effects of short-chain inulin (OP), natural inulin (OH), and long-chain inulin (OHP) at substitution levels of 3%, 6%, and 9%, as well as freezing of 0, 15, and 30 days, on the farinograph and extensograph characteristics of flour, the rheological properties, water distribution, and microstructure of frozen dough, as well as the quality of the final steamed bread, were investigated. The findings revealed that inulin led to a reduction in the water absorption of the dough while increasing its stable time. Furthermore, inulin delayed the alteration of freezable water within the frozen dough. Notably, the addition of inulin resulted in a more cohesive and evenly arranged network structure within the frozen dough. Steamed bread supplemented with 6% OP, 6% OH, and 3% OHP consistently dislayed a higher specific volume and spread ratio. These findings offer valuable insights into the utilization of inulin in frozen wheat foods.

Direct enzymatic hydrolysis of solid wheat straw with endo-xylanases: Effect of the temperature on the hemicellulose release and the product profile modulation

Prebiotics are non-digestible compounds that promote intestinal microbiota growth and/or activity. Xylooligosaccharides (XOS) are new prebiotics derived from the hemicellulose fraction of lignocellulosic materials. Challenges in using those materials as sources for prebiotic compounds lie in the hemicellulose extraction efficiency and the safety of those ingredients. In this sense, this work aims to optimize hemicellulose extraction and XOS production through direct enzymatic hydrolysis of alkali pre-treated wheat straw without undesired byproducts. By increasing the temperature of the enzymatic step from 40 °C to 65 °C we achieved an improvement in the extraction yield from 55 % to 80 %. Products with different degrees of polymerization were also noticed: while XOS ≤ X6 where the main products at 40 °C, a mixture of long arabinoxylan derived polymers (ADPo) and XOS ≤ X6 was obtained at 65 °C, irrespective of the extraction yield. Thus, a modulatory effect of temperature on the product profile is suggested here. Among the XOS ≤ X6 produced, X2-X3 were the main products, and X4 was the minor one. At the end of the hydrolysis, 146.7 mg XOS per gram of pre-treated wheat straw were obtained.

Facile fabrication of regenerated cellulose-based separators for high-performance lithium-ion batteries by regulating degrees of polymerization

Cellulose-based separators have great application prospects in the field of lithium-ion batteries (LIBs) due to their excellent wettability and thermal stability. However, most current cellulose-based separators come from high-cost nanocellulose and bacterial cellulose. Herein, regenerated cellulose (RC) separators were prepared from dissolving pulp with different degrees of polymerization (DPs) by using the NaOH/urea/thiourea dissolution system as well as a nonsolvent-induced phase separation method. The results showed that the DP of cellulose had a significant influence on the mechanical properties, pore structure, and electrochemical properties of the resultant RC separator. An appropriate increase in the DP could improve the mechanical strength, porosity, and ionic conductivity of the separator. The RC separator with a DP of 599 exhibited the best performance with a porosity of 56.1 %, an average pore size of 305 nm, an electrolyte uptake of 339 %, a tensile strength of 38.3 MPa, and an ionic conductivity of 1.88 mS·cm−1. The lithium-ion battery prepared with the optimal RC separator had a specific capacity of 156.55 mAh/g for 100 cycles at a current density of 0.5 C and a coulombic efficiency of more than 96 %, which was a clear advantage over the commercially available Celgard2400 and cellulose separators. This work makes contributions to the development of high-performance LIBs separators from cellulose.

Surface Modification of Cellulose Nanocrystal Films via RAFT Polymerization for Adsorption of PFAS

Cellulose nanocrystals (CNCs) are bio-based materials able to be functionalized following different approaches, which expands their range of applications. One such approach is surface-initiated polymerization, which involves the attachment of an initiator to the CNC’s surface to initiate the growth of the polymer. This work reports the modification of CNCs using the described approach. First, a CNC-based film was prepared, on which an initiator (RAFT agent) was grafted, and then (trimethylaminoethyl methacrylate, a positively charged monomer, was polymerized using reversible addition–fragmentation chain-transfer (RAFT) polymerization. The CNC film was successfully modified and fully characterized. Different degrees of polymerization were targeted to emphasize the effect of the positively charged polymer and their chain length on the adsorption efficiency. The results showed that by increasing the chain length of the grafted polymer, up to 80% of both pollutants could be removed, with a faster adsorption of PFOS as compared to PFOA.

The Degree of Inulin Polymerization Is Important for Short-Term Amelioration of High-Fat Diet (HFD)-Induced Metabolic Dysfunction and Gut Microbiota Dysbiosis in Rats.

Inulin, a non-digestible polysaccharide, has gained attention for its prebiotic properties, particularly in the context of obesity, a condition increasingly understood as a systemic inflammatory state linked to gut microbiota composition. This study investigates the short-term protective effects of inulin with different degrees of polymerization (DPn) against metabolic health deterioration and gut microbiota alterations induced by a high-fat diet (HFD) in Sprague Dawley rats. Inulin treatments with an average DPn of 7, 14, and 27 were administered at 1 g/kg of bodyweight to HFD-fed rats over 21 days. Body weight, systemic glucose levels, and proinflammatory markers were measured to assess metabolic health. Gut microbiota composition was analyzed through 16S rRNA gene sequencing. The results showed that inulin27 significantly reduced total weight gain and systemic glucose levels, suggesting a DPn-specific effect on metabolic health. The study also observed shifts in gut microbial populations, with inulin7 promoting several beneficial taxa from the Bifidobacterium genera, whilst inducing a unique microbial composition compared to medium-chain (DPn 14) and long-chain inulin (DPn: 27). However, the impact of inulin on proinflammatory markers and lipid metabolism parameters was not statistically significant, possibly due to the short study duration. Inulin with a higher DPn has a more pronounced effect on mitigating HFD-induced metabolic health deterioration, whilst inulin7 is particularly effective at inducing healthy microbial shifts. These findings highlight the benefits of inulin as a dietary adjuvant in obesity management and the importance of DPn in optimizing performance.

Evaluation of biological activity and prebiotic properties of proanthocyanidins with different degrees of polymerization through simulated digestion and in vitro fermentation by human fecal microbiota

The bioactive activity of proanthocyanidins (PAs) is closely associated with their degree of polymerization (DP), however, the effects of PAs with different DP on digestion and gut microbiota have remained unclear. To investigate this, we conducted in vitro simulated digestion and colonic fermentation studies on samples of PAs with different DP. The results showed that PAs was influenced by both protein precipitation and enzymolysis, resulting in a decrease in functional activity. PAs with a high DP were more sensitive to the gastrointestinal environment. The significant clustering trend in colonic fermentation verified the reliability of multivariate statistical techniques for screening samples with distinct functional differences. The gut microbiota analysis showed that oligomeric PAs had a stronger promoting effect on beneficial bacteria, while high polymeric PAs had a greater inhibitory effect on harmful bacteria. This study offers new insights into the biological activity and microbiological mechanisms of PAs with different DP.

Hydrolysis mechanism of the cyclohexaborate anion: Unraveling the intricacies.

is a highly polymerized borate anion of three six-membered rings. Limited research on the hydrolysis mechanism under neutral solution conditions exists. Calculations based on density functional theory show that undergoes five steps of hydrolysis to form H3 BO3 and . At the same time, there are a small number of borate ions with different degrees of polymerization during the hydrolysis process, such as triborate, tetraborate, and pentaborate anions. The structure of the borate anion and the coordination environment of the bridging oxygen atoms control the hydrolysis process. Finally, this work explains that in existing experimental studies, the reason for the low content in solution environments with low total boron concentrations is that it depolymerizes into other types of borate ions and clarifies the borate species. The conversion relationship provides a basis for identifying the possibility of various borate ions existing in the solution. This work also provides a certain degree of theoretical support for the cause of the "dilution to salt" phenomenon.

Towards non-traditional intrinsic luminescence luminogens from polystyrene derivative C5 skeletal polymers and ladder polymers with well-regulated microstructures

With the emergence of new emissive species in many nonconjugated structures, how to efficiently design and manipulate non-traditional intrinsic luminescence luminogens (NTILgens) is of academic importance but a dramatic challenge. As the carbon skeletons in olefin polymers have diverse microstructures that mainly affect molecular packing, the construction of the carbon skeletons is required to regulate the performances of luminescent materials. Our group previously reported the C5 skeletal P-CPVB and its ladder polymer (C-PCPVB) through the anion migrated ring-opening polymerization (AMROP) of 1-cyclopropylvinylbenzene (CPVB) and the cationic cyclization of P-CPVB. Unexpected, after the rigid seven membered rings were constructed among the phenyl rings, the NTIL was observed of the nonconjugated C-PCPVB in the aggregate state under UV light irradiation. The results inspired us to design the polymer luminogens through the construction of carbon skeletons. In present work, the P-CPVBs and their ladder polymers (C-PCPVBs) with different degree of polymerization (DPs) are prepared. Unexpected, P-CPVBs with different DPs were non-emissive in dilute solution but highly emissive with the visible light in the solid state under the UV light irradiation. As predicted, C-PCPVBs with different DPs fluoresced blue emission in the aggregation state. All the P-CPVBs in the solid state showed much higher absolute quantum yields (QY) values than C-PCPVB analogues did. The bright blue emissions in the aggregate state of both C-PCPVBs bearing nonconjugated groups and P-CPVBs bearing poorly conjugated groups could be attributed to the clusterization-triggered emission (CTE), but the mechanisms to generate NTIL were different due to the difference of the carbon skeletons, where the through-spacing conjugation (TSC) and through-spacing interactions (TSI), respectively, contributed to the NTIL of C-PCPVBs and P-CPVBs. In perspective of the property-oriented designability, their derivatives with different electron-donating and -withdrawing substituents (P-CPVB-OCH3/TPSE/yne, C-PCPVB-OCH3/TPSE/yne) when the DPs were fixed at 24 were synthesized and characterized. All the substituted P-CPVBs/C-PCPVBs were demonstrated with the aggregation-induced emission (AIE) effect and blue fluorescence as the unsubstituted P-CPVBs/C-PCPVBs. As desired, the electronic effect of carbon skeletons and their cyclization can affect their maximum emission wavelengths (λem) and the QY. All the λem values were red-shifted whether the carbon skeletons were cyclic or substituted. More importantly, the glass temperature (Tg) and decomposition temperature (Td) of P-CPVB were dramatically improved by the substituents and cyclization analogues. The seven-membered ring and the crosslinking networks of the yne group in the warming up can significantly improve the stability of polymers, contributing to the higher Td value. It should be noted that P-CPVB-yne and C-PCPVB-yne exhibited the much higher Td values, and they showed the higher carbonization yield of 49.78% and 45.25% at 800 ℃, respectively, which would broaden their applications of these nonpolar polymers.

Microscopic Properties of Asphalt and Polyethylene at an Extraordinary High Dosage through Molecular Dynamics Simulation

Using waste plastics in asphalt mixtures could be an exploratory way to dispose of waste plastics. This study aims to investigate the microscopic properties between asphalt and polyethylene (PE) at an extraordinary dosage of 20 wt.%. Various types of PE with different degrees of polymerization (DP) and structural configurations were considered. Molecular dynamics simulations were used to calculate the mechanical parameters, free volume ratio (FVR), and Flory–Huggins parameter of the resulting PE-modified asphalt (PEA). Two types of PEA were made and characterized by fluorescence microscopy. The simulation results indicate that the addition of PE reduces the density of modified asphalt by less than 5%, and a higher density of PEA is associated with a lower FVR. When the FVR is close, the mechanical properties are greatly influenced by the DP and configuration. The DP and the number of chains are the main parameters impacting the compatibility between PE and asphalt, based on the Flory–Huggins parameter analysis. Decreasing the DP of PE (e.g., 50, with a minimum Flory–Huggins parameter and a relative molecular mass of 1300) will significantly increase the compatibility between asphalt and PE. LDPE−2 has better compatibility with asphalt, possibly because LDPE−2 has higher purity. These findings provide valuable insights into plastic thermal cracking and industrial modification practices.

Green Process for Producing Xylooligosaccharides by Using Sequential Auto-hydrolysis and Xylanase Hydrolysis.

Xylooligosaccharides (XOS), as prebiotic oligomers, are increasingly receiving attention as high value-added products produced from lignocellulosic biomass. Although the XOS contains a series of different degrees of polymerization (DP) of xylose units, DP 2 and 3 (xylobiose (X2) and xylotriose (X3)) are regarded as the main active components in food and pharmaceutical fields. Therefore, in the study, in order to achieve the maximum production of XOS with the desired DP, a combination strategy of sequential auto-hydrolysis and xylanase hydrolysis was developed with corncob as raw material. The evidences showed that the hemicellulosic xylan could be effectively decomposed into various higher DP saccharides (> 4), which were dissolved into the auto-hydrolysate; sequentially, the soluble saccharides could be rapidly hydrolyzed into XOS with desired DP by xylanase hydrolysis. Finally, a maximum XOS yield of 56.3% was achieved and the ratio of (X2 + X3)/XOS was over 80%; meanwhile, the by-products could be controlled at lower levels. Overall, this study provides solid data that support the selective and precise preparation of XOS from corncob, vigorously promoting the application of XOS as functional sugar products.

Inulin-type fructans with different degrees of polymerization improve insulin resistance, metabolic parameters, and hormonal status in overweight and obese women with polycystic ovary syndrome: A randomized double-blind, placebo-controlled clinical trial.

Polycystic ovary syndrome (PCOS) is associated with reproductive disorders and adverse cardiometabolic risk factors that can negatively impact the general health of women. Inulin-type fructans (ITFs) are proposed to beneficially affect risk factors associated with metabolic disorders. Whether ITFs can help with the management of PCOS by modifying insulin resistance (IR) and androgen levels has not yet been explored. The aim of this study was to investigate the effects of ITFs with different degrees of polymerization on insulin resistance, blood lipids, anthropometric measures, and hormonal status in overweight and obese women with PCOS. In a randomized double-blind placebo-controlled trial, seventy-five women with PCOS aged 18-40 years old were randomly assigned to receive 10 g/day of high-performance inulin (HPI) or oligofructose-enriched inulin (OEI) or maltodextrin for 12 weeks. Biochemical and clinical outcomes were measured at baseline and after the intervention. Participants in the HPI and OEI groups experienced improvements in waist circumference, total testosterone, free androgen index, sex hormone-binding globulin, and triglycerides compared to the placebo group. Also, the number of women with irregular menses or oligomenorrhoea decreased significantly in both ITF groups. Participants in the HPI group reported lower body mass, fasting insulin, and HOMA-IR, as well as a higher quantitative insulin sensitivity check index. ITF supplementation, especially with long-chain ITFs, when given for 12 weeks may improve metabolic outcomes, androgen status and clinical manifestations in women with PCOS.

Glucans with Different Degrees of Polymerization from Leuconostoc mesenteroides CICC6055: Analysis of Physicochemical Properties and Intestinal Prebiotic Function.

This study explored the physicochemical properties and prebiotic activities of glucans and oligoglucans. Oligoglucans were obtained through the fermentation of Leuconostoc mesenteroides CICC6055 and the glucansucrase of strain CICC6055, while glucans were obtained only through fermentation. Thin-layer chromatography and high-performance liquid chromatography identified enzymatically synthesized oligoglucans with a higher yield. Differential scanning calorimetry and derivative thermogravimetry analyses revealed the heat resistance of the glucans and oligoglucans at 280-300 °C. Fourier transform-infrared spectroscopy and nuclear magnetic resonance analyses demonstrated that their main chains were linked with α-1,6-glycosidic bonds accompanied by glucose residue branching. In vitro fermentation experiments demonstrated that they not only improved the contents of short-chain fatty acids but also raised the abundance of predominant flora, such as Bacteroides, Firmicutes, Verrucomicrobia, and Proteobacteria. These results implicate glucansucrase as an efficacious tool for the enzyme synthesis of oligoglucans. Furthermore, both polysaccharides with different degrees of polymerization may be beneficial in maintaining a healthy human gut.

Enhanced cryopreservation performance of PVA grafted monolayer graphite oxide with synergistic antifreezing effect and rapid rewarming

In cryopreservation of biological samples such as cells, the formation, growth and recrystallization of ice crystals can cause fatal mechanical damage to cells. Therefore, how to effectively regulate and inhibit ice crystals, reduce freezing damage, and improve cryopreservation efficiency is a critical scientific problem that needs to be addressed in the current cryopreservation field. In this paper, a series of PVA grafted single-layer graphite oxide (PVA-g-GO nanocomposites) with different degrees of polymerization and different proportions was ingeniously engineered by a one-step esterification reaction method to study their ice crystal control effect. The obtained PVA17-g-GO nanocomposite could effectively reduce the ice crystal size during the recrystallization process at low concentration by adsorption and lattice matching. The nanocomposite with a 10:1 mass ratio of PVA and GO exhibited the best ice control effect, which could reduce the ice crystal size to only 17 % of that of pure water. Surprisingly, the modification of PVA significantly enhanced the absorption value of GO in Visible and Near-Infrared light (380 nm–980 nm), giving it excellent photothermal conversion efficiency (39.7 %), accelerating ice thawing rate, and thus synergistically reducing the mechanical damage caused by ice recrystallization. Finally, using the prepared PVA17-g-GO as cryoprotectants (CPA), the cryopreservation experiments on Hela cells and A549 cells demonstrated that this material at low concentration of 20 μg/ml could achieve high cell survival efficiency (>85 %). The preparation and development of this efficient ice-recrystallization-inhibiting nanomaterial with bidirectional synergy can provide new ideas and methods for the safety and progress of current cryopreservation technology.

Spatial Distribution and Characterization of the Small-Molecule Metabolites and In Situ Hydrolyzed Oligosaccharides in the Rhizome of Glycyrrhiza uralensis by Desorption Electrospray Ionization-Mass Spectrometry Imaging and High-Resolution Liquid Chromatography-Mass Spectrometry.

Characterization and spatial distribution studies of the metabolome in plants are crucial for revealing the physiology of plants and developing functional foods. Using the rhizome of Glycyrrhiza uralensis as a case, we integrated desorption electrospray ionization-mass spectrometry imaging (DESI-MSI) and high-resolution liquid chromatography/mass spectrometry approaches aimed at characterizing and locating both the small molecules and the macromolecular polysaccharides. Under the optimal conditions, 21 flavonoids and 12 triterpenoids were detected and characterized in different tissues of the rhizome and another 19 components were characterized exclusively by DESI-MSI. Combined with hydrophilic interaction chromatography/ion mobility-quadrupole time-of-flight mass spectrometry, eight different degrees of polymerization of oligosaccharides (after in situ acid hydrolysis) were characterized from the rhizome of G. uralensis. Majority of these metabolites are located in the cortex, phloem, and medulla, which lays the foundation for understanding the physiology of G. uralensis. The useful information can benefit the sustainable utilization and further development of Glycyrrhiza resource.

Poly(N-methyl-N-vinylacetamide): A Strong Alternative to PEG for Lipid-Based Nanocarriers Delivering siRNA.

Lipid-based nanocarriers have demonstrated high interest in delivering genetic material, exemplified by the success of Onpattro and COVID-19 vaccines. While PEGylation imparts stealth properties, it hampers cellular uptake and endosomal escape, and may trigger adverse reactions like accelerated blood clearance (ABC) and hypersensitivity reactions (HSR). This work highlights the great potential of amphiphilic poly(N-methyl-N-vinylacetamide) (PNMVA) derivatives as alternatives to lipid-PEG for siRNA delivery. PNMVA compounds with different degrees of polymerization and hydrophobic segments, are synthesized. Among them, DSPE (1,2-distearoyl-sn-glycero-3-phosphoethanolamine)-PNMVA efficiently integrates into lipoplexes and LNP membranes and prevents protein corona formation around these lipid carriers, exhibiting stealth properties comparable to DSPE-PEG. However, unlike DSPE-PEG, DSPE-PNMVA24 shows no adverse impact on lipoplexes cell uptake and endosomal escape. In in vivo study with mice, DSPE-PNMVA24 lipoplexes demonstrate no liver accumulation, indicating good stealth properties, extended circulation time after a second dose, reduced immunological reaction, and no systemic pro-inflammatory response. Safety of DSPE-PNMVA24 is confirmed at the cellular level and in animal models of zebrafish and mice. Overall, DSPE-PNMVA is an advantageous substitute to DSPE-PEG for siRNA delivery, offering comparable stealth and toxicity properties while improving efficacy of the lipid-based carriers by minimizing the dilemma effect and reducing immunological reactions, meaning no ABC or HSR effects.

Production of cellooligosaccharides from oil palm bunch in bio-based choline chloride deep eutectic solvents and MALDI-TOF MS analysis of COS mixture

Lignocellulosic biomass pretreatment and cellulose dissolution are principal challenges for its conversion to high-value chemicals, materials and fuels. This work focused on production of soluble cellooligosaccharides (COS) from palm bunch for future use as nutraceutical supplement to enhance human's immune and digestive systems. Deep eutectic solvents (DESs) have been found as eco-friendly, renewable and promising solvents selective for lignin and hemicellulose removal from biomass. Additionally, the investigation of most suitable DES for both cellulose dissolution and subsequently cleavage of cellulose to COS is crucial. In the study, palm empty fruit bunch (EFB) was pretreated in different DES for screening of most favorable cellulose inter- and intra-molecular structural dissolution in a combination with beta,1–4 glycosidic bond cleavage by elevated reaction temperature for COS production. ChCl/urea was found to be the most promising DES for dissolving 76.83% of EFB constituents. The highest COS production yield at 90.1%w/w based on treated EFB fraction (74.7% COS yield based on cellulose in native EFB) was achieved in ChCl/urea DES from cellulose fraction extracted from EFB at 240 °C for 20 min. The study additionally provided insightful characterization and elucidation of COS molecular structure using 2D-HSQC and MALDI-TOF/MS techniques. MALDI-TOF/MS was a promising and rapid technique for simultaneously qualitative and quantitative analysis of COS at different degrees of polymerization in COS product.

Nanoscale Insights into the Protection of Calcium Silicate Hydrate by Polydimethylsiloxane Coatings in Sulfate Environments: Different Degrees of Polymerization

Calcium silicate hydrate (CSH) plays a crucial role in concrete by controlling its properties and durability. The degradation of CSH often signifies concrete damage. Polydimethylsiloxane (PDMS) is commonly used to protect concrete from sulfate corrosion; however, the comprehensive mechanistic understanding of its protective effects against CSH remains limited. Here, molecular dynamics (MD) simulations were employed to explore atomic-scale interactions between PDMS coatings and CSH in a sulfate-rich environment. Our results reveal that PDMS mitigates sulfate-induced CSH decalcification by forming a positively charged layer, ultimately reducing sulfate bonding by 83.3% compared to the blank group. Molecular structure analysis highlights key hydrogen bonding and calcium–oxygen bonding interactions that are critical for this protection. Higher polymerization stabilizes substrate adsorption, reducing surface diffusion to 33.3% of low-polymerization PDMS, thereby enhancing protection. Additionally, water molecule interactions with the CSH matrix are negatively correlated with the amount of adsorbed sulfate. Simulation results offer valuable insights into the molecular-level dynamic response of the material, contributing to a deeper understanding of the protective mechanisms of PDMS against sulfate-induced CSH degradation in concrete. These findings can guide experimenters and engineers in designing more effective protective coatings for concrete exposed to sulfate-rich environments, thereby laying a foundation for further experimental research and the development of concrete materials with enhanced durability under challenging environmental conditions.

In-situ preparation of triazole polymerization films on copper surface via SI-ATRP method and their performance against copper corrosion

As one of the most advanced film forming technologies, the surface-initiated controlled/living radical polymerization provides an effective method for in-situ fabricating functional films on material surface. In this paper, the triazole film of polymerized (1-tosyl-1H-1,2,3-triazol-4-yl) methyl acrylate (P-TTMA) is in-situ prepared on copper surface via Cu catalyzed surface-initiated atom transfer radical polymerization (SI-ATRP) method. The P-TTMA film with different degree of polymerization (DP) is obtained by varying its molecular weight, which is achieved via regulating the polymerization time of SI-ATRP reaction. When the polymerization time is within 48 h, the SI-ATRP system can achieve a regular chain growth of P-TTMA film, the DP value of P-TTMA film shows an S-shaped variation as the polymerization time increasing. The electrochemical test is performed to evaluate the anticorrosion performance of different P-TTMA films for copper. The result demonstrates that the P-TTMA films exhibit good anticorrosion performance for Cu in 3.5 wt% NaCl solution. The P-TTMA obtained by 48 h polymerization time, with the DP value of 105, exhibits the stable and good protection performance. The anticorrosion performance of P-TTMA film can be optimized via regulating the SI-ATRP reaction. This paper provides a new idea for preparing inhibition film with a certain degree of polymerization and protection performance on metal surface. It is expected to be a theoretical guidance for fabricating triazole polymer film using ATRP with lower catalyst loading or metal-free ATRP in the coming future.

Genome Sequencing-Based Mining and Characterization of a Novel Alginate Lyase from Vibrio alginolyticus S10 for Specific Production of Disaccharides.

Alginate oligosaccharides prepared by alginate lyases attracted great attention because of their desirable biological activities. However, the hydrolysis products are always a mixture of oligosaccharides with different degrees of polymerization, which increases the production cost because of the following purification procedures. In this study, an alginate lyase, Alg4755, with high product specificity was identified, heterologously expressed, and characterized from Vibrio alginolyticus S10, which was isolated from the intestine of sea cucumber. Alg4755 belonged to the PL7 family with two catalytic domains, which was composed of 583 amino acids. Enzymatic characterization results show that the optimal reaction temperature and pH of Alg4755 were 35 °C and 8.0, respectively. Furthermore, Alg4755 was identified to have high thermal and pH stability. Moreover, the final hydrolysis products of sodium alginate catalyzed by Alg4755 were mainly alginate disaccharides with a small amount of alginate trisaccharides. The results demonstrate that alginate lyase Alg4755 could have a broad application prospect because of its high product specificity and desirable catalytic properties.