Wood Hemicelluloses Research Articles (Page 1)

Enhanced peroxymonosulfate activation for ciprofloxacin degradation enabled by a delignified wood-derived carbon.

Wood is a green and renewable bio-based building material, but its hygroscopicity affects its dimensional stability, limiting its use in construction. Chemical modification can improve its properties, yet its effectiveness depends on wood permeability and traditional modifiers. This study first used a deep eutectic solvent (DES) to boost the permeability of North American alder wood. Then, methyl trimethoxysilane was impregnated under supercritical carbon dioxide (SCI), pressure (PI), vacuum (VI), and atmospheric pressure (AI) conditions. DES treatment damaged the cell structure, increasing wood permeability. Silane was deposited and polymerized in the cell lumen, chemically bonding with cell-wall components, filling walls and pits, and thickening walls. The VI group had the highest absolute density (0.59 g/cm3, +36.6%) and the lowest moisture absorption (4.4%, −33.3%). The AI group had the highest ASE (25%). The PI group showed the highest surface hardness (RL, 2592 N) and a water contact angle of 131.9°, much higher than natural wood. Overall, the VI group had the best performance. Silane reacts with cellulose, hemicellulose, and lignin in wood via hydrolysis and hydroxyl bonding, forming stable bonds that enhance the treated wood’s hydrophobicity, dimensional stability, and surface hardness.

Extraction and chemical features of wood hemicelluloses: A review.

Composition and distribution of phenolic compounds of optimized bilberry microcapsules using wood hemicelluloses as protecting materials.

Xylem plasticity is important for trees to coordinate hydraulic efficiency and safety under changing soil water availability. However, the physiological and transcriptional regulations of cambium on xylem plasticity are not well understood. In this study, mulberry saplings of drought-resistant Wubu and drought-susceptible Zhongshen1 were subjected to moderate or severe drought stresses for 21 days and subsequently rewatered for 12 days. The anatomical, physiological and transcriptional responses in wood and cambium were analyzed. Most parameters were not affected significantly under moderate drought for both cultivars. Severe drought led to decreased vessel lumen diameter and increased vessel frequency, increased starch and hemicellulose in wood of both cultivars. Notably, increased soluble sugars and lignin were detected only in wood of Wubu. In cambial zone, levels of starch, glucose, fructose, mannose and cytokinin were decreased in both cultivars, whereas soluble sugars were increased in Wubu but deceased in Zhongshen1. RNA-sequencing identified 1824 and 2471 differentially expressed genes in Wubu and Zhongshen1 under severe drought, respectively. These responses were partially recovered after rewatering. Weighted gene correlation network analysis identified modules of co-expressed genes correlated with the anatomical and physiological traits of wood and cambium, with the turquoise and green modules most strongly correlated with traits under drought or rewatering. These modules were enriched in gene ontology terms related to cell division, cytoskeleton organization, cell wall modification, dark respiration, vesicle transport and protein metabolism. Detailed gene expression patterns indicate that reprogramming of cambium activity was relatively similar in both cultivars, but at different scales. These findings provide important insights into the physiological and molecular mechanisms underlying xylem plasticity based on cambium and offer valuable references for breeding drought-resistant mulberry and other woody species in light of future drier climate scenarios.

Wood hemicelluloses as protective materials for preserving the viability of probiotic Lacticaseibacillus rhamnosus GG during spray drying

Bioactive peptides (BPs) derived from agri-food side-streams display great potential as functional ingredients and nutraceuticals. However, BPs can be susceptible to environmental stressors and food processing conditions and typically exist as an aqueous mixture of various peptides, making their storage and use in foods very challenging. Microencapsulation offers a solution, utilizing suitable wall materials to create a protective matrix and transform them into powders for improved stability and application versatility. Here, we investigated the possibility of creating freeze-dried microencapsulated BP powders from bread waste using maltodextrin as the wall material to maintain their antifungal properties against Penicillum albocoremium, Eurotium herbariorum and Penicillium roqueforti fungi. The results were compared to those obtained from galactoglucomannans (GGM) and glucuronoxylans (GX) sourced from forest industry side-streams, aiming to explore their potential suitability as innovative materials for microencapsulating BPs. Maltodextrin microcapsules exhibited the highest inhibition rate on the tested fungi (10 − 44%), followed by GX (26 − 39%) and then GGM (9 − 14%) counterparts. Interactions between wall materials and BPs, as illustrated by FTIR analyses, were found to be the cause of variations in antifungal activities among BP microcapsules. The use of wall materials, especially wood hemicelluloses, facilitated freeze drying of BPs. However, their application in food products is restricted by the decline in the BP bioactivity resulting from the freeze drying process. For this reason, additional research on alternative drying methods is needed. The results of this study are expected to open new ways of production of stable functional ingredients from side-streams of the forest and food industries.

This study takes the wooden components of the different parts of the ancient buildings at the site of the Zhuangzishang Conference as the object of study, and investigates the deterioration state of the different wood components. To assess their degree of degradation, the wood anatomy, basic density (BD), maximum water content (MWC), cell wall major components, X-ray diffraction (XRD), infrared spectroscopy (IR), and thermogravimetry (TG) were used to compare the samples of new and old wood from the same species. The window (W) was identified by microscopic characterization as cypress (Cupressus sp.), the footing beam (FB) and the weatherboard (WB) as pine (Pinus spp.), the purlin (P) and the column (C) as Chinses fir (Cunninghamia spp.), and the floor (F) as spruce (Picea sp.). In terms of their physical properties, the old wood had a lower basic density of 2.58%–38.19%, a lower air-dry density of 2.87%–39.81%, and a higher maximum moisture content of 8.52%–41.38% compared to the reference wood. The degradation of the FB, which has been subjected to moisture and sunlight, and the P, which has been subjected to termite damage, was greater than that of their conspecifics. The integrated holocellulose of the ancient wood was 3.34%–16.48% less, and the hemicellulose was 1.6%–21.92% less compared to that of the reference wood, and the lignin was 1.32%–25.07% more. The XRD results showed that the crystallinity of the cellulose was greater in the different species of ancient wood compared to the control wood, which was caused by the decrease in the amorphous zones of the hemicellulose and cellulose in the ancient wood. The IR indicated that the degradation of cellulose and hemicellulose occurred in the old wood of all species, from the new lignin uptake peaks in the UV-exposed W, FB, and WB compared to the control timber. The pyrolytic behavior of the ancient and control timber is mainly related to the degradation of the tree species and the ancient wood holocellulose. These results show that the differences in the wooden components of the different parts of the ancient buildings at the Zhuangzishang Conference site are mainly related to the species of trees used in the components, and are secondly related to the location of the ancient wood members, which provides useful information for the protection and repair of the ancient buildings at the site.

Lightweight reinforced wood beams through compression of its surface layers combined with the removal of lignin and hemicellulose

Xylitol is an important product of xylan valorization — the main hemicellulose of birch and aspen wood. Xylitol is obtained by direct hydrogenation of xylose. In present study, the xylose was obtained by acid hydrolysis of birch wood xylan. The industrial catalyst for the xylitol production process is Raney nickel. Pyrophoricity, tendency to sintering, Ni leaching and contamination of the product are actual problems of its use. We have developed new supported ruthenium catalysts based on mesoporous silicate SBA-15 doped with zirconia. The proposed method of modification of SBA-15 by doping with zirconia improves the hydrothermal stability. The deposited Ru is present in the form of highly dispersed RuO2 particles and is distributed evenly. The catalysts are stable, safe and environmentally friendly. Their high catalytic activity allows the process to be carried out in very mild conditions – in pure water at 70 °C and a pressure of 5.5 MPa H2. While the catalysts provide 96-99% selectivity for xylitol. The introduction of the developed catalysts into the xylitol production might reduce the product purification cost of and the process energy consumption, thereby improving ecological and economic indicators of deep chemical processing of plant raw materials.

In-situ growth of hexaconazole/polydopamine/hexadecyltrimethoxysilane in multi-scale structured wood to prepare superhydrophobic wooden materials with decay resistance

In-situ immobilization of MIL-100(Fe) on the microchannels in wood aerogel: Efficient persulfate activation toward antibiotic removal

The biodegradation path and mechanism of wood varies depending on diverse fungi and tree species, as fungi possess selectivity in degradation of versatile wood components. This paper aims to clarify the actual and precise selectivity of white and brown rot fungi and the biodegradation effects on different tree species. Softwood (Pinus yunnanensis and Cunninghamia lanceolata) and hardwood (Populus yunnanensis and Hevea brasiliensis) were subjected to a biopretreating process by white rot fungus Trametes versicolor, and brown rot fungi Gloeophyllum trabeum and Rhodonia placenta with various conversion periods. The results showed that the white rot fungus Trametes versicolor had a selective biodegradation in softwood, which preferentially convert wood hemicellulose and lignin, but cellulose was retained selectively. Conversely, Trametes versicolor achieved simultaneous conversion of cellulose, hemicellulose and lignin in hardwood. Both brown rot fungi species preferentially converted carbohydrates, but R. placenta had a selectivity for the conversion of cellulose. In addition, morphological observation showed that the microstructures within wood changed significantly, and the enlarged pores and the improved accessibility could be beneficial for the penetration and accessibility of treating substrates. The research outcomes could serve as fundamental knowhows and offer potentials for effective bioenergy production and bioengineering of bioresources, and provide a reference for further application of fungal biotechnology.

Wood hemicelluloses as sustainable wall materials to protect bioactive compounds during spray drying of bilberries

A holistic utilization of all lignocellulosic wood biomass, instead of the current approach of using only the cellulose fraction, is crucial for the efficient, ecological, and economical use of the forest resources. Use of wood constituents in the food and feed sector is a potential way of promoting the global economy. However, industrially established food products utilizing such components are still scarce, with the exception of cellulose derivatives. Hemicelluloses that include xylans and mannans are major constituents of wood. The wood hemicelluloses are structurally similar to hemicelluloses from crops, which are included in our diet, for example, as a part of dietary fibers. Hence, structurally similar wood hemicelluloses have the potential for similar uses. We review the current status and future potential of wood hemicelluloses as food ingredients. We include an inventory of the extraction routes of wood hemicelluloses, their physicochemical properties, and some of their gastrointestinal characteristics, and we also consider the regulatory route that research findings need to follow to be approved for food solutions, as well as the current status of the wood hemicellulose applications on that route.

The most commonly-used and effective wall materials (WMs) for spray-dried microencapsulation of bioactive compounds are either costly, or derived from unsustainable sources, which lead to an increasing demand for alternatives derived from sustainable and natural sources, with low calories and low cost. Wood hemicelluloses obtained from by-products of forest industries appear to be attractive alternatives as they have been reported to have good emulsifying properties, low viscosity at high concentrations, high heat stability and low heat transfer. Here, we investigated the applicability of spruce galactoglucomannans (GGM) and birch glucuronoxylans (GX), to encapsulate flaxseed oil (FO, polyunsaturated fatty acid-rich plant based oil) by spray drying; and the results were compared to those of the highly effective WM, gum Arabic (GA). It was found that depending on solid ratios of WM:FO (1:1, 3:1 and 5:1), encapsulation efficiency of GGM was 88–96%, and GX was 63–98%. At the same encapsulation ratio, both GGM and GX had higher encapsulation efficiency than GA (49–92%) due to their ability to produce feed emulsions with a smaller oil droplet size and higher physical stability. In addition, the presence of phenolic residues in GGM and GX powders enabled them to have a greater ability to protect oil from oxidation during spray drying than GA. Physiochemical properties of encapsulated powders including thermal properties, morphology, molecular structure, particle size and water adsorption intake are also investigated. The study has explored a new value-added proposition for wood hemicelluloses which can be used as effective WMs in the production of microcapsules of polyunsaturated fatty acid-rich oils for healthy and functional products in food, pharmaceutical and cosmetic industries.

Many natural polysaccharides have biological activity, which allows them to be used to obtain medicines. The development of new methods for the isolation of polysaccharides from plant materials, as well as the study of their properties and structure, is an actual task. In this work the polysaccharide galactoglucomannan (GGM) was isolated from pine wood time by the peroxide delignification in the “acetic acid-water” medium in the presence (NH4)6Mo7O24.Its yield was 10.1 wt.% from the weight of wood and 58.1 wt.% from the content of hemicelluloses in wood. By 13С NMR method it was found that the degree of GGM acetylation is 0.23 with substitution of carbon atoms of the pyranose ring at C2 and C3. According to the X-ray data, GGM has an amorphous supramolecular structure. The polysaccharide gluoxylan (GX) was isolated by alkaline extraction from the cellulose product obtained after peroxide delignification. Its yield was 4.3 wt.%. from wood and 24.5 wt.% from the content of hemicelluloses in wood.Glucoxylan does not contain acetyl groups (data from IR and NMR spectroscopy), it has a crystalline supramolecular structure and is poorly soluble in water. Composition and structure of the obtained polysaccharides were studied using chemical methods of analysis, IR spectroscopy, 1H, 13C, 2D HSQC NMR spectroscopy, gas chromatography, X-ray analysis.

Wood is an organic renewable natural resource. Cellulose, hemicellulose and lignin in wood are used in tissue engineering, biomedicine and other fields because of their good properties. This paper reported that the possibility of wood fiber gel material molding and the preparing of gel material were researched based on the wood fiber gel material as a 3D printing material. A five-degree of freedom hybrid three nozzle 3D printer was designed. The structural analysis, static analysis, modal analysis and transient dynamic analysis of 3D printers were researched, and the theoretical basis of the 3D printer was confirmed as correct and structurally sound. The results showed that the 5-DOF hybrid 3-nozzle 3D printer achieved the 3D printing of wood fiber gel material and that the printer is capable of multi-material printing and multi-degree-of-freedom printing.

Over the last few decades, chemical and physical studies on bowed string musical instruments have provided a better understanding of their wooden finished surface. Nevertheless, until now only a few of them investigated the effects of the chemical pre-treatments in the traditional making procedures. Those treatments are believed to affect wood properties, its interaction with the following treatments (i.e. varnish application) and its vibro-mechanical behaviour (that may contribute to the acoustical properties of musical instruments). In this study, two traditional alkaline treatments were applied to reference samples of spruce wood, the wood commonly used to make violins’ soundboards. An integrated analytical strategy, which combines infrared spectroscopy, analytical pyrolysis coupled to gas chromatography-mass spectrometry, and gel permeation chromatography, was employed to investigate the chemical alterations of lignocellulosic polymers (cellulose, hemicellulose, and lignin). Results have shown that the selected alkaline treatments induce the partial hydrolysis of the hemicellulose chains and a slight decrease in the crystallinity of cellulose. We could also prove: (i) the cleavage of lignin-carbohydrate complexes formed by the covalent bonds between hemicellulose and lignin in spruce wood, and (ii) the partial breaking of the hydrogen bonds network in cellulose. According to the literature, the alteration of the lignin-carbohydrate complexes is responsible for changes in wood mechanical behaviour. Hence, future perspectives of this research could outline new knowledge on the vibro-mechanical behaviour of the violin soundboard and the consequent acoustics.

Spruce (Piceaabies) wood hemicelluloses have been obtained by the noncatalytic and catalytic oxidative delignification in the acetic acid-water-hydrogen peroxide medium in a processing time of 3–4 h and temperatures of 90–100 °C. In the catalytic process, the H2SO4, MnSO4, TiO2, and (NH4)6Mo7O24 catalysts have been used. A polysaccharide yield of up to 11.7 wt% has been found. The hemicellulose composition and structure have been studied by a complex of physicochemical methods, including gas and gel permeation chromatography, Fourier-transform infrared spectroscopy, and thermogravimetric analysis. The galactose:mannose:glucose:arabinose:xylose monomeric units in a ratio of 5:3:2:1:1 have been identified in the hemicelluloses by gas chromatography. Using gel permeation chromatography, the weight average molar mass Mw of hemicelluloses has been found to attain 47,654 g/mol in noncatalytic delignification and up to 42,793 g/mol in catalytic delignification. Based on the same technique, a method for determining the α and k parameters of the Mark–Kuhn–Houwink equation for hemicelluloses has been developed; it has been established that these parameters change between 0.33–1.01 and 1.57–472.17, respectively, depending on the catalyst concentration and process temperature and time. Moreover, the FTIR spectra of the hemicellulose samples contain all the bands characteristic of heteropolysaccharides, specifically, 1069 cm−1 (C–O–C and C–O–H), 1738 cm−1 (ester C=O), 1375 cm−1 (–C–CH3), 1243 cm−1 (–C–O–), etc. It has been determined by the thermogravimetric analysis that the hemicelluloses isolated from spruce wood are resistant to heating to temperatures of up to ~100 °C and, upon further heating, start destructing at an increasing rate. The antioxidant activity of the hemicelluloses has been examined using the compounds simulating the 2,2-diphenyl-2-picrylhydrazyl free radicals.