Water Excitation Research Articles

Water excitation with LIBRE pulses in three-dimensional variable flip angle fast spin echo for fat-free and large field of view imaging at 3 tesla

PurposeTo develop and evaluate a sequence in which water excitation with lipid insensitive binomial off-resonant radio frequency excitation (LIBRE) pulses is incorporated into three-dimensional (3D) variable flip angle fast spin echo (LIBRE-vf-FSE) for fat-free and large field of view imaging at 3 Tesla (T). Materials and methodsNumerical simulation was conducted to optimize the parameters of LIBRE pulses, including the flip angle, pulse duration, and frequency offset, for maximizing the fat suppression effect of the proposed LIBRE-vf-FSE sequence. The sequence was then implemented at 3 T and assessed in phantoms, lower extremity imaging of 8 healthy volunteers, and head/neck imaging of 5 healthy volunteers. Conventional water excitation (WE) and fat saturation (FatSat) were also performed for comparison. Signal-to-noise ratio (SNR) of fat and contrast-to-noise ratio (CNR) between fat and water were used to evaluate the level of fat suppression. Standard deviation (SD) of SNR was used to evaluate the uniformity of fat suppression. ResultsThe numerical simulation demonstrated that LIBRE-vf-FSE enables large volume imaging with uniform fat suppression, which was further confirmed by phantom and healthy volunteer experiments. LIBRE provided the lowest fat SNR and offered more uniform fat suppression compared with the WE and FatSat. Specifically, average oil SNRs obtained by LIBRE (1.10 ms, 360 Hz, and 60°), WE, and FatSat were (180.1 vs. 280.2 vs. 811.2) in phantom experiments, and average fat SNRs and SDs in legs obtained by LIBRE (1.10 ms, 360 Hz, and 60°), WE, and FatSat were (85.1 vs. 105.0 vs. 105.1) and (22.4 vs. 27.4 vs. 56.4) in vivo experiments, respectively. ConclusionThe proposed LIBRE-vf-FSE sequence allows for fat suppression and large field of view imaging at 3 T. It could be an alternative approach for fat-free vf-FSE scan.

Clinically compatible subject-specific dynamic parallel transmit pulse design for homogeneous fat saturation and water-excitation at 7T: Proof-of-concept for CEST MRI of the brain.

To evaluate the benefits and challenges of dynamic parallel transmit (pTx) pulses for fat saturation (FS) and water-excitation (WE), in the context of CEST MRI. "Universal" kT -points (for FS) and spiral non-selective (for WE) trajectories were optimized offline for flip angle (FA) homogeneity. Routines to optimize the pulse shape online, based on the subject's fields maps, were implemented (target FA of 110°/0° for FS, 0°/5° for WE at fat/water frequencies). The pulses were inserted in a CEST sequence with a pTx readout. The different fat suppression schemes and their effects on CEST contrasts were compared in 12 volunteers at 7T. With a 25%-shorter pulse duration, pTx FS largely improved the FA homogeneity (root-mean-square-error(RMSE)= 12.3° vs. 53.4° with circularly-polarized mode, at the fat frequency). However, the spectral selectivity was degraded mainly in the cerebellum and close to the sinuses (RMSE=5.8° vs. 0.2° at the water frequency). Similarly, pTx WE showed a trade-off between FA homogeneity and spectral selectivity compared to pTx non-selective pulses (RMSE=0.9° and 1.1° at the fat and water frequencies, vs. 4.6° and 0.5°). In the brain, CEST metrics were reduced by up to 31.9% at -3.3ppm with pTx FS, suggesting a mitigated lipid-induced bias. This clinically compatible implementation of dynamic pTx pulses improved the fat suppression homogeneity at 7T taking into account the subject-specific B0 heterogeneities online. This study highlights the lipid-induced biases on the CEST z-spectrum. The results are promising for body applications where B0 heterogeneities and fat are more substantial.

Differences between 3D isovoxel fat suppression VIBE MRI and CT models of proximal femur osseous anatomy: A preliminary study for bone tumor resection planning.

To evaluate the osseous anatomy of the proximal femur extracted from a 3D-MRI volumetric interpolated breath-hold (VIBE) sequence using either a Dixon or water excitation (WE) fat suppression method, and to measure the overall difference using CT as a reference standard. This retrospective study reviewed imaging of adult patients with hip pain who underwent 3D hip MRI and CT. A semi-automatically segmented CT model served as the reference standard, and MRI segmentation was performed manually for each unilateral hip joint. The differences between Dixon-VIBE-3D-MRI vs. CT, and WE-VIBE-3D-MRI vs. CT, were measured. Equivalence tests between Dixon-VIBE and WE-VIBE models were performed with a threshold of 0.1 mm. Bland-Altman plots and Lin's concordance-correlation coefficient were used to analyze the agreement between WE and Dixon sequences. Subgroup analyses were performed for the femoral head/neck, intertrochanteric, and femoral shaft areas. The mean and maximum differences between Dixon-VIBE-3D-MRI vs. CT were 0.2917 and 3.4908 mm, respectively, whereas for WE-VIBE-3D-MRI vs. CT they were 0.3162 and 3.1599 mm. The mean differences of the WE and Dixon methods were equivalent (P = 0.0292). However, the maximum difference was not equivalent between the two methods and it was higher in WE method. Lin's concordance-correlation coefficient showed poor agreement between Dixon and WE methods. The mean differences between the CT and 3D-MRI models were significantly higher in the femoral shaft area (P = 0.0004 for WE and P = 0.0015 for Dixon) than in the other areas. The maximum difference was greatest in the intertrochanteric area for both techniques. The difference between 3D-MR and CT models were acceptable with a maximal difference below 3.5mm. WE and Dixon fat suppression methods were equivalent. The mean difference was highest at the femoral shaft area, which was off-center from the magnetization field.

Effectiveness of fat suppression using a water-selective binomial-pulse excitation in chemical exchange saturation transfer (CEST) magnetic resonance imaging.

The purpose of this study was to characterize the individual contribution of multiple fat peaks to the measured chemical exchange saturation transfer (CEST) signal when using water-selective binomial-pulse excitation and to determine the effects of multiple fat peaks in the presence of B0 inhomogeneity. The excitation profiles of multiple binomial pulses were simulated. A CEST sequence with binomial-pulse excitation and modified point-resolved spectroscopy localization was then applied to the in vivo lumbar spinal vertebrae to determine the signal contributions of three distinct groups of lipid resonances. These confounding signal contributions were measured as a function of the irradiation frequency offset to determine the effect of the multi-peak nature of the fat signal on CEST imaging of exchange sites (at 1.0, 2.0 and 3.5ppm) and robustness in the presence of B0 inhomogeneity. Numerical simulations and in vivo experiments showed that water excitation (WE) using a 1-3-3-1 (WE-4) pulse provided the broadest signal suppression, which provided partial robustness against B0 inhomogeneity effects. Confounding fat signal contributions to the CEST contrasts at 1.0, 2.0 and 3.5ppm were unavoidable due to the multi-peak nature of the fat signal. However, these CEST sites only suffer from small lipid artifacts with ∆B0 spanning roughly from - 50 to 50Hz. Especially for the CEST site at 3.5ppm, the lipid artifacts are smaller than 1% with ∆B0 in this range. In WE-4-based CEST magnetic resonance imaging, B0 inhomogeneity is the limiting factor for fat suppression. The CEST sites at 1.0, 2.0ppm and 3.5ppm unavoidably suffer from lipid artifacts. However, when the ∆B0 is confined to a limited range, these CEST sites are only affected by small lipid artifacts, which may be ignorable in some cases of clinical applications.

Free-running 5D coronary MR angiography at 1.5T using LIBRE water excitation pulses.

To implement, optimize, and characterize lipid-insensitive binomial off-resonant RF excitation (LIBRE) pulses for fat-suppressed fully self-gated free-running 5D cardiac MRI. Bloch equation simulations were used to optimize LIBRE parameter settings in non-interrupted bSSFP prior to in vitro validation. Thus, optimized LIBRE pulses were subsequently applied to free-running coronary MRA in 20 human adult subjects, where resulting images were quantitatively compared to those obtained with non-fat-suppressing excitation (SP), conventional 1-2-1 water excitation (WE), and a previously published interrupted free-running (IFR) sequence. SAR and scan times were recorded. Respiratory-and-cardiac-motion-resolved images were reconstructed with XD-GRASP, and contrast ratios, coronary artery detection rate, vessel length, and vessel sharpness were computed. The numerically optimized LIBRE parameters were successfully validated in vitro. In vivo, LIBRE had the lowest SAR and a scan time that was similar to that of WE yet 18% shorter than that of IFR. LIBRE improved blood-fat contrast when compared to SP, WE, and IFR, vessel detection relative to SP and IFR, and vessel sharpness when compared to WE and IFR (for example, for the left main and anterior descending coronary artery, 51.5% ± 10.2% [LIBRE] versus 42.1% ± 6.8% [IFR]). Vessel length measurements remained unchanged for all investigated methods. LIBRE enabled fully self-gated non-interrupted free-running 5D bSSFP imaging of the heart at 1.5T with suppressed fat signal. Measures of image quality, vessel conspicuity, and scan time compared favorably to those obtained with the more conventional non-interrupted WE and the previously published IFR, while SAR reduction offers added flexibility.

Noncontrast free-breathing respiratory self-navigated coronary artery cardiovascular magnetic resonance angiography at 3\u2009T using lipid insensitive binomial off-resonant excitation (LIBRE)

BackgroundRobust and homogeneous lipid suppression is mandatory for coronary artery cardiovascular magnetic resonance (CMR) imaging since the coronary arteries are commonly embedded in epicardial fat. However, effective large volume lipid suppression becomes more challenging when performing radial whole-heart coronary artery CMR for respiratory self-navigation and the problem may even be exacerbated at increasing magnetic field strengths. Incomplete fat suppression not only hinders a correct visualization of the coronary vessels and generates image artifacts, but may also affect advanced motion correction methods. The aim of this study was to evaluate a recently reported lipid insensitive CMR method when applied to a noncontrast self-navigated coronary artery CMR acquisitions at 3 T, and to compare it to more conventional fat suppression techniques.MethodsLipid insensitive binomial off resonant excitation (LIBRE) radiofrequency excitation pulses were included into a self-navigated 3D radial GRE coronary artery CMR sequence at 3 T. LIBRE was compared against a conventional CHESS fat saturation (FS) and a binomial 1–180°-1 water excitation (WE) pulse. First, fat suppression of all techniques was numerically characterized using Matlab and experimentally validated in phantoms and in legs of human volunteers. Subsequently, free-breathing self-navigated coronary artery CMR was performed using the LIBRE pulse as well as FS and WE in ten healthy subjects. Myocardial, arterial and chest fat signal-to-noise ratios (SNR), as well as coronary vessel conspicuity were quantitatively compared among those scans.ResultsThe results obtained in the simulations were confirmed by the experimental validations as LIBRE enabled near complete fat suppression for 3D radial imaging in vitro and in vivo. For self-navigated whole-heart coronary artery CMR at 3 T, fat SNR was significantly attenuated using LIBRE compared with conventional FS. LIBRE increased the right coronary artery (RCA) vessel sharpness significantly (37 ± 9% (LIBRE) vs. 29 ± 8% (FS) and 30 ± 8% (WE), both p < 0.05) and led to a significant increase in the measured RCA vessel length to (83 ± 31 mm (LIBRE) vs. 56 ± 12 mm (FS) and 59 ± 27 (WE) p < 0.05).ConclusionsApplied to a respiratory self-navigated noncontrast 3D radial whole-heart sequence, LIBRE enables robust large volume fat suppression and significantly improves coronary artery image quality at 3 T compared to the use of conventional FS and WE.

Flexible water excitation for fat-free MRI at 3T using lipid insensitive binomial off-resonant RF excitation (LIBRE) pulses.

To develop a robust and flexible low power water excitation pulse that enables effective fat suppression at high magnetic field strength. A water excitation method that uses spatially non-selective pulses was optimized in numerical simulations, and implemented and tested in phantoms and healthy volunteers at 3T. The lipid insensitive binomial off-resonant excitation (LIBRE) pulse comprises two low power rectangular subpulses that have a variable frequency offset, phase offset and duration. The capability and extent of LIBRE fat suppression was quantitatively compared with conventional fat saturation (FS) and water excitation (WE) techniques. LIBRE enables simultaneous water excitation and near complete fat suppression in large volumes at 3T as demonstrated by numerical simulations, and experiments. In phantoms and in human subjects, the frequency responses matched well with those from the numerical simulation. Comparing FS and WE, LIBRE demonstrated an improved robustness to magnetic field inhomogeneities, and a much more effectively suppressed fat signal. This applied for a range of pulse durations and pulses as short as 1.4 ms. A flexible water excitation method was developed that shows robust, near complete fat suppression at 3T. Magn Reson Med 79:3007-3017, 2018. © 2017 International Society for Magnetic Resonance in Medicine.

Validation of high temporal resolution spiral phase velocity mapping of coronary artery blood flow against Doppler flow wire

Background The temporal pattern of coronary artery flow velocity through the cardiac cycle provides important information about coronary haemodynamics. The ‘gold standard’ for coronary artery velocity assessment is the Doppler flow wire which is inserted directly into the coronary artery under X-ray fluoroscopic guidance, which is invasive, uses ionising radiation and has a small but significant risk of serious complication. In this study, we perform an in vivo comparison of coronary blood flow velocities measured with breath-hold high temporal resolution spiral phase velocity mapping and Doppler flow wire measurements. Methods Breath-hold proximal coronary artery velocity maps were acquired in 5 left anterior descending (LAD) and 3 right coronary arteries (RCAs) in patients who had undergone invasive Doppler flow wire assessment as part of a clinical assessment. Acquisition parameters were: pixel size 1.4 × 1.4 mm (reconstructed to 0.7 ×0 .7 mm) ×8m m, true temporal resolution 19 ms, 1-1 water excitation (WE), 17 cardiac cycle breath-hold, velocity sensitivity 30-50cm/s, retrospective ECG gating (reconstructed 50 phases). Extraction of MR coronary artery blood flow velocitytime curves was performed using a custom MATLAB program which tracked the motion of the vessel over the cardiac cycle and corrected for the through-plane motion of the vessel using a region of adjacent tracked myocardium (LAD) or a region of surrounding epicardial fat (RCA) from a separately acquired fat-excitation acquisition. For each vessel, the mean through-plane motioncorrected MR velocities at all timepoints were plotted against the equivalent flow wire velocities. If necessary, the profiles were first time-shifted to take into account small differences in data triggering between the two techniques. The correlation between the two profiles was assessed using simple linear regression analysis. Results Figures 1 and 2 show example LAD and RCA studies. On average, the MR measured velocities were 66% less than the Flowire velocities (SD 9%, range: 50% - 78%). The correlation between the MR and flow wire data, however, was high, with R 2 values ranging from 0.6 - 0.95 in the 8 vessels studied (mean R 2 = .80).

Diffusion-weighted echo-planar imaging of the head and neck using 3-T MRI: Investigation into the usefulness of liquid perfluorocarbon pads and choice of optimal fat suppression method

PurposeTo investigate whether image quality can be improved using liquid perfluorocarbon pads (Sat Pad) and clarify the optimal fat-suppression method among chemical shift selective (CHESS), water excitation (WEX), and short TI inversion recovery (STIR) methods in diffusion-weighted imaging (DWI) of the head and neck using 3-T magnetic resonance imaging. Correlations between results of visual inspection and quantitative analysis were also examined. Material and MethodsThis study was approved by our Institutional Review Board and informed consent was waived. DWI was performed on 25 subjects with/without Sat Pad and using three fat-suppression methods (6 patterns). Image quality was evaluated visually (4-point scales and lesion-depiction capability) and by quantitative analysis (signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR)). Two-way repeated-measures analysis of variance (ANOVA) was used to detect significant differences in scores of visual evaluation, SNR, and CNR. ResultsMean visual evaluation scores were significantly higher with Sat Pad using STIR than without Sat Pad for all fat-suppression methods (P<0.05). DWI with Sat Pad using STIR tended to be useful for depicting lesions. DWI using STIR showed reduced W-SNR (W: whole area of depicted structure) and CNR (between semispinalis capitis muscle and subcutaneous fat) due to fewer artifacts and uniform fat suppression. ConclusionCombining Sat Pad with STIR provides good image quality for visual inspections. When numerous artifacts are present and fat suppression is insufficient, higher SNR and CNR do not always provide good diagnostic image quality.

Comparison of PD BLADE with fat saturation (FS), PD FS and T2 3D DESS with water excitation (WE) in detecting articular knee cartilage defects

The purpose of this study, is to compare the sequences: 1) proton density (PD) BLADE (BLADE is a PROPELLER-equivalent implementation of the Siemens Medical System) with fat saturation (FS) coronal (COR), 2) PD FS COR, 3) multi-planar reconstruction (MPR) with 3mm slice thickness and 4) multi-planar reconstruction (MPR) with 1.5mm slice thickness, both from the T2 3D-double-echo steady state (DESS) with water excitation (WE) sagittal (SAG), regarding their abilities to identify changes in the femorotibial condyle cartilage in knee MRI examinations. Thirty three consecutive patients with osteoarthritis (18 females, 15 males; mean age 56years, range 37–71years), who had been routinely scanned for knee examination using the previously mentioned image acquisition techniques, participated in the study. A quantitative analysis was performed based on the relative contrast (ReCON) measurements, which were taken both on normal tissues as well as on pathologies. Additionally, a qualitative analysis was performed by two radiologists. Motion and pulsatile flow artifacts were evaluated. The PD BLADE FS COR sequence produced images of higher contrast between Menisci and Cartilage, Fluid and Cartilage, Pathologies and Cartilage as well as of the Conspicuousness Superficial Cartilage and it was found to be superior to the other sequences (p<0.001). The sequences T2 3D DESS 1.5mm and T2 3D DESS 3mm were significantly superior to the PD BLADE FS COR and the PD FS COR sequences in the visualization of Bone and Cartilage and the Conspicuousness Deep Surface Cartilage. This pattern of results is also confirmed by the quantitative analysis. PD FS BLADE sequences are ideal for the depiction of the cartilage pathologies compared to the conventional PD FS and T2 3D DESS sequences.

SU‐E‐I‐71: Detection of Articular Knee Cartilage Defects Using PD BLADE with Fat Saturation (FS), PD FS and T2 3D DESS with Water Excitation (WE)

Purpose: The purpose of this study, is to compare the sequences: 1) proton density (PD) BLADE with fat saturation (FS) coronal (COR), 2) PD FS COR, 3) multi‐planar reconstruction (MPR) with 3mm slice thickness and 4) multi‐planar reconstruction (MPR) with 1.5mm slice thickness, both derived from the T2 3D‐double‐echo steady state (DESS) with water excitation (WE) sagittal (SAG) sequence, regarding their abilities to identify changes in the femorotibial condyle cartilage in knee MRI examinations. Methods: Thirty three consecutive patients with osteoarthritis (18 females, 15 males; mean age 56 years, range 37‐71 years), who had been routinely scanned for knee examination using the previously mentioned image acquisition techniques, participated in the study. A quantitative analysis was performed based on the relative contrast (ReCON) measurements, which were taken both on normal tissues as well as on pathologies. Additionally, a qualitative analysis was performed by two radiologists. Motion and pulsatile flow artifacts were evaluated. Results: The PD BLADE FS COR sequence produced images of higher contrast between Menisci and Cartilage, Fluid and Cartilage, Pathologies and Cartilage as well as of the Conspicuousness Superficial Cartilage and it was found to be superior to the other sequences (p&lt;0.001). The sequences T2 3D DESS 1.5mm and T2 3D DESS 3mm were significantly superior to the PD BLADE FS COR and the PD FS COR sequences in the visualization of Bone, Cartilage and the Conspicuousness Deep Surface Cartilage. This pattern of results is also confirmed by the quantitative analysis. Also, in the PD BLADE FS COR sequence, the results of the Truncation Artifact, Pulsation Artifact, Edge Sharpness and Blurring Artifacts, were superior to the other sequences (p&lt;0.001). Conclusion: PD FS BLADE sequences are ideal for the depiction of the cartilage pathologies compared to the conventional PD FS and T2 3D DESS sequences.

Articular Cartilage Defects Detected with 3D Water-Excitation True FISP: Prospective Comparison with Sequences Commonly Used for Knee Imaging

To prospectively compare the accuracy of three-dimensional (3D) water-excitation (WE) true fast imaging with steady-state precession (FISP) in the diagnosis of articular cartilage defects with that of sequences commonly used to image the knee, with arthroscopy or surgery as the reference standard. This study protocol was institutional review board approved. Written informed consent was obtained from all patients. Thirty knees in 29 patients (mean age, 56 years; range, 18-86 years) were prospectively evaluated by using sagittal 3D WE true FISP with two section thicknesses (1.7 mm [true FISPthin] and 3.0 mm [true FISPthick]), two-dimensional (2D) intermediate-weighted spin-echo with fat saturation, 2D fast short inversion time inversion-recovery, 3D WE double-echo steady-state, and 3D fat-saturated fast low-angle shot sequences. Cartilage defects were graded on magnetic resonance images and during surgery with a modified Noyes scoring system. Contrast-to-noise ratio (CNR) and CNR efficiency were calculated. Sensitivity, specificity, and accuracy were assessed. Interobserver agreement was determined with kappa statistics, and quantitative results were evaluated with the Wilcoxon signed rank test. The performance of 3D WE true FISPthick (sensitivity, specificity, and accuracy, respectively, were 52%, 93%, and 71% for reader 1 and 65%, 88%, and 76% for reader 2) and 3D WE true FISPthin (sensitivity, specificity, and accuracy, respectively, were 58%, 94%, and 75% for reader 1 and 63%, 80%, and 71% for reader 2) sequences was no different than that of other sequences in the detection of circumscribed defects. Three-dimensional WE true FISP sequences had a significantly (P<.0033) higher CNR and CNR efficiency between cartilage and fluid than the corresponding sequences with the same section thickness. Three-dimensional WE true FISP enables high contrast between joint fluid and articular cartilage and a diagnostic performance that is comparable with that of standard sequences.

The value of water-excitation 3D FLASH and fat-saturated PDw TSE MR imaging for detecting and grading articular cartilage lesions of the knee.

To evaluate the diagnostic accuracy of water-excitation (WE) 3D FLASH and fat-saturated (FS) proton density-weighted (PDw) TSE MR imaging for detecting, grading, and sizing articular cartilage lesions of the knee. A total of 26 patients underwent MR imaging prior to arthroscopy with the following sequences: (1) WE 3D FLASH: 28/11 ms, scan time: 4 min 58 s, flip angle: 40 degrees; (2) FS PDw TSE: 3433/15 ms, scan time: 6 min 15 s, flip angle: 180 degrees. Grade and size of the detected lesions were quantified and compared with the results of arthroscopy for each compartment. The sensitivity, specificity, positive and negative predictive values, and accuracy for detecting cartilage lesions were 46%, 92%, 81%, 71% and 74% for WE 3D FLASH and 91%, 98%, 96%, 94% and 95% for FS PDw TSE MR imaging. WE 3D FLASH correlated significantly with arthroscopy for grading on the patella ( P<0.0001) and the femoral trochlea ( P=0.02) and for sizing on the femoral trochlea ( P=0.03). FS PDw correlated significantly ( P<0.0001) with arthroscopy for grading and sizing on all compartments. FS PDw TSE is an accurate method for detecting, grading and sizing articular cartilage lesions of the knee and yielded superior results relative to WE 3D FLASH MR imaging.

Selective water excitation for faster MR imaging of articular cartilage defects: initial clinical results.

Our objective was to compare a water-excitation (WE) 3D fast low-angle shot (FLASH) MR sequence for faster imaging of articular cartilage defects of the knee to a conventional fat-saturated (FS) 3D FLASH MR sequence. This prospective study included 16 knees of 16 patients with suspected cartilage lesions. The MR imaging in transverse and sagittal planes included (a) FS 3D FLASH (TR/TE: 45 ms/11 ms, scan time 8 min, flip angle 50 degrees), and (b) WE 3D FLASH (TR/TE: 28 ms/11 ms, scan time 4 min 58 s, flip angle 40 degrees). For each sequence signal-to-noise ratios (SNR) and contrast-to-noise ratios (CNR) were quantified. The detected cartilage lesions were evaluated using a semi-quantitative four-scale scoring system (grades 0-III). The data were compared between the sequences using the paired Student's t-test. No statistically significant differences between the sequences were found for SNR, CNR, and cartilage defect grading (p=0.14-0.8). The WE 3D FLASH MR imaging seems to be promising for fast imaging of articular cartilage lesions of the knee.

Optimization and validation of a rapid high-resolution T1-w 3D FLASH water excitation MRI sequence for the quantitative assessment of articular cartilage volume and thickness

In view of follow up, survey and development of therapeutic strategies for osteoarthritis where cartilage deterioration plays an important role, a non invasive, reliable and quantitative assessment of the articular cartilage is desirable. The currently available high resolution T1-weighted (T1-w) 3D FLASH pulse sequences with frequency selective fat suppression are very time consuming. We have 1) optimized a high resolution T1-w 3D FLASH water excitation (WE) sequence for short acquisition time and cartilage visualization, and 2) validated this sequence for cartilage volume and thickness quantification. The spectral fat presaturation was replaced by selective water excitation. The flip angle of the WE sequence was optimized for the contrast to noise (C/Ncart) ratio of cartilage. Sagittal datasets (voxel size: 0.31 × 0.31 × 2 mm3) of the knees of nine healthy volunteers were acquired both, with the 3D FLASH WE (17.2/6.6/30°) sequence (WE) and a previously validated 3D FLASH fat saturated (42/11/30°) sequence (FS). For validation of the WE sequence, cartilage volume, mean and maximal cartilage thickness of the two sequences were compared. Reproducibility was assessed by calculating the coefficient of variation (COV %) of 4 consecutive WE data sets in the volunteers. The acquisition time was reduced from 16′30″ (FS) down to 7′14″ for the WE sequence. Image contrast and visualization of the cartilage was very similar, but delineation of the basal layer of the cartilage was slightly improved with the WE sequence. A flip angle of 30° provided the best C/Ncart ratios (WE). Reproducibility (COV) was between 1.9 and 5.9%. Cartilage volume and thickness agreed within 4% between FS and WE sequence. The WE sequence allows for rapid, valid and reproducible quantification of articular cartilage volume and thickness, prerequisites for follow-up examinations. The reduced acquisition time (50% of FS) enables routine clinical application and thus may contribute to a broader assessment of osteoarthritis.

Magnetic resonance imaging of the wrist--comparison of high resolution pulse sequences and different fat signal suppression techniques in cadavers

To evaluate high resolution sequences with and without fat-suppression techniques for MR imaging of the wrist. 10 cadaver wrist specimens were imaged with 12 MR sequences (SE: 400 ms/20 ms, TSE: 3000 ms/119 ms/17 ms, fatsat (FS) TSE: 3000 ms/17 ms and 3000 ms/45 ms, STIR: 2619 ms/29 ms/160 ms, DESS 3D: 43.7 ms/9 ms/35 degrees FS and 25.4 ms/9 ms/35 degrees water excitation (WE), CISS 3D: 12.2 ms/5.9 ms/40 degrees and FLASH-sequences: 53 ms/11 ms/40 degrees FS, 23 ms/11 ms/40 degrees WE and 45 ms/11 ms/30 degrees FS) at 1.5 T. Slice thickness was 3 mm, FOV 80 x 70 mm (pixel size 0.31 x 0.31 mm). Signal intensity was measured by an ROI in bone marrow, fluid, hyaline cartilage, scapholunate (SL) ligament and triangular fibrocartilage and S/N- and C/N-ratios were calculated. Additionally, a visual evaluation was performed. The highest homogeneity and the least artifacts were achieved by the T1-w SE sequence. For the STIR and PD-FS TSE sequence high rankings were found for the detection of free water. The PD FS sequence had high ranking also for visualization of the SL ligament and the triangular fibrocartilage. The best sequence for the assessment of hyaline cartilage was the FLASH-FS sequence. For detailed analysis of bony structures the CISS sequence performed best. The isolated use of a PD-FS-TSE sequence enables for evaluation of all clinically relevant structures at the wrist. Dedicated questions for hyaline cartilage are answered best by the use of a FLASH 3D-FS sequence. Selective water excitation reduces acquisition time to 60%, nevertheless FS sequences are still diagnostically superior to WE sequences.