Water Contact Angle Hysteresis Research Articles

Sulfobetaine Zwitterions with Embedded Fluorocarbons: Synthesis and Interfacial Properties.

We describe the preparation of a new set of fluorinated sulfobetaine (FSB) zwitterionic polymers in which fluorocarbon moieties are attached directly to the zwitterionic components. An efficient two-step modification to the conventional sulfobetaine methacrylate monomer synthesis gave access to a series of polymer zwitterions containing varying extents of fluorocarbon character. FSB methacrylates proved amenable to homo- and copolymerizations using reversible addition-fragmentation chain transfer (RAFT) conditions, affording polymers with molecular weights ranging from 5 to 20 kDa and with low molecular weight distributions. Thin films of FSB homopolymers on glass proved stable to aqueous environments and exhibited increasing hydrophobicity with fluorocarbon content, as well as remarkably large water contact angle hysteresis values that enable pinning of water droplets on hydrophobic surfaces, reminiscent of the "petal effect" found in nature. FSB-containing copolymers in aqueous media demonstrated markedly reduced oil-water interfacial tension values, even with moderate (20-50 mol %) FSB incorporation.

Chemical and structural heterogeneity of olive leaves and their trichomes

Many biological surfaces have hairs, known as trichomes in plants. Here, the wettability and macro- and micro-scale features of olive leaves are analyzed. The upper leaf side has few trichomes, while the lower side has a high trichome density. By combining different techniques including electron and atomic force microscopy, trichome surfaces are found to be chemically (hydrophilic-hydrophobic) heterogeneous at the nano-scale. Both olive leaf surfaces are wettable by water, having a high water contact angle hysteresis and great drop adhesion. The ultra-structural pattern observed for epidermal pavement cells differs from the reticulate cuticle structure of trichomes which shows that leaf surface areas may be substantially different despite being located nearby. Our study provides evidence for the nano-scale chemical heterogeneity of a trichome which may influence the functional properties of biological surfaces, such as water and solute permeability or water capture as discussed here for plants.

Superhydrophobic, antibacterial, and EMI shielding properties of Ag/PDMS-coated cotton fabrics

In this study, three functionalities of superhydrophobicity, antibacterial activity and electromagnetic interference (EMI) shielding of cotton fabrics coated with Ag/PDMS were studied, and the role of coating composition was discussed. Special attention was paid to understanding the relationships between the surface roughness of coated fibres with the developed superhydrophobicity and antibacterial activity. The superhydrophobicity of fabrics was analysed based on water contact angle (WCA) and contact angle hysteresis (CAH) values while the antibacterial activity was tested against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria. It was found that the surface roughness on fibres, which changed by altering the concentrations of Ag NPs (0.2–4 g/L) and PDMS (20 and 40 g/L), affected the obtained superhydrophobicity. The most superhydrophobic fabric (WCA 171°) was coated with a formulation containing Ag NPs (2 g/L), and PDMS (20 g/L), and had the highest surface roughness. Increasing the ingredients’ concentrations, however, deteriorated the optimum roughness as measured using a 3D Surface Laser Scanning Microscopy method. The coated fabrics showed efficacy against both types of bacteria, and it was confirmed that the Ag NPs content was the key factor in determining the antibacterial performance. Moreover, testing the EMI shielding performance of fabrics demonstrated that increasing the concentrations of Ag NPs and PDMS both enhanced the reflection coefficient (R) of fabrics against incident X-band electromagnetic (EM) wave by around >500%, which was due to the deposition of a higher amount of Ag NPs on fabrics. The superhydrophobicity of fabrics was durable after 1000 abrasion cycles, and the fabrics retained their antibacterial activity even after numerous washings.Graphical

Wettability-driven synergistic resistance of scale and oil on robust superamphiphobic coating

Disgusting deposits (e.g., scale and crude oil) in daily life and industrial production are always serious problems, posing great threats to the safety and economic development. However, most of developed coatings can only conquer one part of these deposits such as superhydrophobic coatings possess anti-scaling capacity but would adhere crude oil. To integrate scale resistance with oil repellence, we herein report a robust superamphiphobic (SAB) coating simultaneously reducing pollution of scale and oil for extended period of time (two weeks with over 98% reduction). Compared with single role of superhydrophobic and amphiphilic surfaces, the SAB coating can not only inhibit interfacial nucleation of scale but also reduce the adhesion of formed scale and polluted oil. The durability of the SAB coating is evaluated via mechanical tests (sandpaper abrasion, tape stripping and sand falling) and chemical corrosion (corrosive liquid immersing), revealed by sustainable high contact angles and low contact angle hysteresis of water and oil. The universality of this strategy can be further confirmed by adding different particles like kaolin, Al2O3, and SiO2, resisting multiple types of scale (i.e., CaSO4, BaSO4 and MgCO3) and oil (i.e., glycerol, glycol, and mineral oil). Therefore, this study provides an ideal avenue for resisting scale and oil, which may be used for conquering the complexity of application environments (e.g., oil production and transportation).

Superhydrophobicity on AISI 304 stainless steel through surface sensitization process and etching

In this research, the surface sensitization process of austenitic stainless steel (304) was used to create the superhydrophobicity through a facile etching method with a significantly lower etching time. In order to utilize the surface sensitization process for the purpose of forming island-like chromium carbide on surface, oxyacetylene flame heat-treatment was performed at 650 °C for one min. After HF etching at ambient temperature, treatment in nitric acid, and the reduction of surface energy by stearic acid modification, a water contact angle (WCA) of 167°, water sliding angle (WSA) of 3°, and water contact angle hysteresis (WCAH) of 7° have been achieved. The sensitization process makes the sample susceptible to intergranular corrosion and uniform micro- and nano-sized pores entirely cover the surface after boiling in nitric acid. This phenomenon is the main reason for creating the hierarchical microstructure on the surface of stainless steel in a shorter time.

Exploring the water capture efficiency of covalently attached liquid-like surfaces.

The capture of moisture from the atmosphere through condensation has the potential to provide a sustainable source of water. Here, we investigate the condensation of humid air at low subcooling condition (11 °C), similar to conditions for natural dew capture, and explore how water contact angle and contact angle hysteresis affect the rates of water capture. We compare water collection on three families of surfaces: (i) hydrophilic (polyethylene oxide, MPEO) and hydrophobic (polydimethylsiloxane, PDMS) molecularly thin coatings grafted on smooth silicon wafers, which produce slippery covalently attached liquid surfaces (SCALSs), with low contact angle hysteresis (CAH = 6°); (ii) the same coatings grafted on rougher glass, with high CAH (20°-25°); (iii) hydrophilic polymer surfaces [poly(N-vinylpyrrolidone), PNVP] with high CAH (30°). Upon exposure to water, the MPEO SCALS swell, which likely further increases their droplet shedding ability. MPEO and PDMS coatings collect similar volume of water (around 5 l m-2day-1), both when they are SCALS and non-slippery. Both MPEO and PDMS layers collect about 20% more water than PNVP surfaces. We present a basic model showing that, under low heat flux conditions, on all MPEO and PDMS layers, the droplets are so small (600-2000 µm) that there is no/low heat conduction resistance across the droplets, irrespective of the exact value of contact angle and CAH. As the time to first droplet departure is much faster on MPEO SCALS (28min) than on PDMS SCALS (90min), slippery hydrophilic surfaces are preferable in dew collection applications where the collection time frame is limited.

Ice Adhesion Evaluation of PTFE Solid Lubricant Film Applied on TiO2 Coatings

Ice formation affects the performance of many industrial components, including aircraft wings, spacecraft, and power transmission cables. In particular, ice build-up on airplane components increases drag and fuel consumption. A large number of studies have been carried out to reduce ice adhesion by developing passive methods such as icephobic coatings and active ice removal approaches such as mechanical vibrations or chemical-based solutions. Despite remarkable recent breakthroughs in the fabrication of icephobic coatings, passive ice removal solutions require higher durability to resist cyclical mechanical ice detachment treatments. Functionalized TiO2 coatings, applied using the suspension plasma spray (SPS) technique, have been shown to be robust and to have dual-scale characteristics in an ice accretion analysis. In this study, the icephobicity and mechanical durability of a novel duplex coating consisting of polytetrafluoroethylene (PTFE) solid lubricant films on TiO2-coated substrates were evaluated. Notably, various amounts of PTFE were applied on top of the TiO2 coating to identify the ideal quantity required to obtain optimal icephobic properties. Ice was generated in an icing wind tunnel, and the amount of accreted ice was evaluated to assess the anti-icing properties. Wettability parameters, including static water contact angle and contact angle hysteresis, were measured to determine the water mobility and surface energy. Ice shear adhesion to the PTFE-TiO2 duplex coating was measured using a custom-built test rig. The mechanical durability was assessed by measuring the ice shear strength for almost twenty icing–deicing cycles, and after five cycles, the roughness parameters and images taken from the surface of the samples were compared. The combination of PTFE solid lubricant film and TiO2 coating reduced ice adhesion by 70%–90% compared to that of a bare aluminum substrate (reference material). Additionally, the results showed that the application of a uniform layer of PTFE solid lubricant film on dual-scale TiO2 coating significantly reduced ice adhesion and maintained mechanical durability for 25 deicing cycles, making this combination a promising candidate for deicing approaches.

Superhydrophobic and Corrosion Behaviour of PVDF-CeO2 Composite Coatings.

Composite coatings of polyvinylidene fluoride (PVDF)/CeO2 were developed by using the spray approach to explore the wetting and corrosion behaviour of coated materials for applications related to industry. PVDF was combined with different quantities of CeO2 nanoparticles followed by spraying onto glass, aluminium, and steel substrates. The sessile droplet method and microscopy studies were used to assess the wetting behaviour and morphology of the coated surfaces, respectively. The corrosion resistance of uncoated substrates coated with PVDF only was compared with those coated with PVDF/CeO2 nanoparticles through Tafel polarization techniques. In psi, the force of adhesion was measured between the coating layer and the substrates. The PVDF/CeO2-coated steel had a significantly greater water contact angle and lower contact angle hysteresis than coated aluminium and glass substrates, reaching 157 ± 2° and 8 ± 1°, respectively. The corrosion protection efficiency of the superhydrophobic PVDF/CeO2 coatings was considerably higher for steel and aluminium when compared with PVDF coatings. The PVDF/CeO2 coated substrates had modest adhesion between the coating layer and the substrates, but it was still acceptable. Furthermore, the PVDF/CeO2 coatings outperformed PVDF alone in terms of mechanical properties.

Growth-Induced Wrinkles and Dotlike Patterns of a Swollen Fluoroalkylated Thin Film by the Reaction of Surface-Attached Polymethylhydrosiloxane.

The design of hydrophobic surfaces requires a material which has a low solid surface tension and a simple fabrication process for anchoring and controlling the surface morphology. A generic method for the spontaneous formation of robust instability patterns is proposed through the hydrosilylation of a fluoroalkene bearing dangling chains, Rf = C6F13(CH2)3-, with a soft polymethylhydrosiloxane (PMHS) spin-coated gel polymer (0.8 μm thick) using Karstedt catalyst. These patterns were easily formed by an irreversible swelling reaction due to the attachment of a layer to various substrates. The buckling instability was created by two different approaches for a gel layer bound to a rigid silicon wafer substrate (A) and to a soft nonswelling silicone elastomer foundation (B). The observations of grafted Rf-PMHS films in the swollen state by microscopy revealed two distinct permanent patterns on various substrates: dotlike of wavelength λ = 0.4-0.7 μm (A) or wrinkle of wavelength λ = 4-7 μm (B). The elastic moduli ratios of film/substrate were determined using PeakForce quantitative nanomechanical mapping. The characteristic wavelengths (λ) of the patterns for systems A and B were quantitatively estimated in relation to the thickness of the top layer. A diversity of wrinkle morphologies can be achieved by grafting different side chains on pristine PMHS films. The water contact angle (WCA) hysteresis of fluorinated chain (Rf) was enhanced upon roughening the surfaces, giving highly hydrophobic surface properties for water with static/hysteresis WCAs of 136°/74° in the resulting wrinkle (B) and 119°/41° in the dotlike of lower roughness (A). The hydrophobic properties of grafted films on A with various mixtures of hexyl/fluoroalkyl chains were characterized by static CA: WCA 104-119°, ethylene glycol CA 80-96°, and n-hexadecane CA 17-61°. A very low surface energy of 15 mN/m for Rf-PMHS was found on the smoother dotlike pattern.

Highly Transparent, Self-Reinforced, and Hydrophobic Cellulose Acetate Films Fabricated Based on Thermal Stretching and Surface Engineering

Imparting cellulose acetate with surface hydrophobicity and self-cleaning function without sacrificing its high transparency and mechanical robustness is a great challenge. In this work, we report a highly transparent, self-reinforced, and hydrophobic cellulose diacetate (CDA) film, prepared by the combination of non-solvent-induced phase separation, uniaxial thermal stretching, and slippery liquid injection (LI). Results indicate that the surface-modified CDA films have hydrophobicity, with the water contact angle (WCA) increasing from ∼58.2 to 105–109°. Meanwhile, by adjusting the draw ratio, the sliding of liquid on the film surface and the WCA hysteresis are effectively improved, especially the sliding angle of CDA-LI-1.7-200 film decreases from 30.5° (for the unmodified CDA film) to 9.4°. Notably, uniaxial stretching provides enhanced mechanical strength for this antifouling CDA film, with up to 60.2% increase in tensile strength (from 37.2 to 59.6 MPa). Meanwhile, it is noted that the modified CDA film also has excellent transparency (≥92%), even slightly higher than that of the unmodified CDA film (∼91.5%). In addition, the surface-modified CDA films show excellent anti-scratching performance and maintain good liquid repellency even after several cycles of severe scratching. The work would provide guidance for the facile preparation of high-performance and multifunctional CDA films.

Altering the Surface Properties of Metal Alloys Utilizing Facile and Ecological Methods.

The development of a superhydrophobic and, even, water-repellent metal alloy surface is reported utilizing a simple, fast, and economical way that requires minimum demands on the necessary equipment and/or methods used. The procedure involves an initial irradiation of the metallic specimen using a femtosecond laser, which results in a randomly roughened surface, that is subsequently followed by placing the item in an environment under moderate vacuum (pressure 10-2 mbar) and/or under low-temperature heating (at temperatures below 120 °C). The effects of both temperature and low pressure on the surface properties (water contact angle and contact angle hysteresis) are investigated and surfaces with similar superhydrophobicity are obtained in both cases; however, a significant difference concerning their water-repellent ability is obtained. The surfaces that remained under vacuum were water-repellent, exhibiting very high values of contact angle with a very low contact angle hysteresis, whereas the surfaces, which underwent thermal processing, exhibited superhydrophobicity with high water adhesion, where water droplets did not roll off even after a significant inclination of the surface. The kinetics of the development of superhydrophobic behavior was investigated as well. The findings were understood when the surface roughness characteristics were considered together with the chemical composition of the surface.

Liquid-solid triboelectric nanogenerators for a wide operation window based on slippery lubricant-infused surfaces (SLIPS)

Triboelectric nanogenerators (TENG) have emerged as suitable devices that are suitable to harvest widely abundant and renewable blue energy. However, a major drawback in related deployments include the reliability of the system when operating in variable atmospheric conditions. To address this limitation, we propose the integration of slippery lubricant-infused porous surfaces (SLIPS) as key TENG component. For instance, we combine SLIPS with transistor-inspired architectures to develop a robust single-electrode triboelectric nanogenerator (SLIPS-SE-TENG) that is shown to operate effectively under extreme temperature and humidity. For this purpose, we use the energy of water droplets (as in rain) impacting a surface to generate the electrical energy output. Our theoretical calculations and atomic force microscopy measurements show that a small volume of lubricant per surface area (4 μL/ per cm2 of porous PTFE) is sufficient to produce a low water contact angle hysteresis, leading to efficient energy conversion, provided the droplet’s moving velocity on the surface surpasses a threshold (0.3 mm/s). As such, we demonstrate SLIPS-SE-TENG to generate an instantaneous short-circuit current of 3 μA (charge density 8.8 nC/cm2). Importantly, we address the limitations of TENG fabricated with traditional superhydrophobic surfaces, affording a device that works normally and stably in harsh environments, under freezing temperatures or high humidity.

Transparent non-fluorinated superhydrophobic coating with enhanced anti-icing performance

A major challenge of non-fluorinated superhydrophobic coatings is the low robustness of the infused nanoparticles in coating films compromising their non-wetting properties. In this paper we developed a robust transparent superhydrophobic coating using an alkoxysilane binder, fumed silica nanoparticles, and methyltriethoxysilane (MTES), in which MTES can act as a coupling agent between the nanoparticles and the binder to increase the stability of the hierarchical structures. The surface wettability was assessed in terms of contact angle (CA) and contact angle hysteresis (CAH) of water at different subfreezing temperatures. The spray-coated superhydrophobic coating with water CA of 163° showed appropriate adhesion to different substrates, optical transmittance of 80% in the visible-light region, and great non-wetting properties even after various extreme treatments, i.e., waterjet impacting, immersing in pollutants and acid/base solutions for 24 h, tape peeling test, and sandpaper abrasion. Self-cleaning tests demonstrated that the superhydrophobic surface could shed various contaminants in both wet and dry conditions leaving a clear surface behind. Ice-adhesion strength and delay of freezing were studied, and it was found that this superhydrophobic coating displayed excellent durability in icephobic properties. The push-off ice adhesion strength of 13.3 kPa on the superhydrophobic coating after 15 icing/de-icing cycles increased only 15% reaching to 15.4 kPa, confirming the superior icephobic behavior of the coating.

A biomimetic hierarchical structure on selective laser melting titanium with enhanced hydrophilic/hydrophobic surface

A novel approach was developed to construct a hierarchical micro- and nano-structure on selective laser melted (SLM) titanium surface. The process-inherent roughness of SLM-Ti was used as the template for assembling TiO2 nanotube arrays (NTAs) to obtain a series of the micro-/nano- topographies in one step. The results show that TiO2 NTAs on SLM-Ti without ultraviolet irradiation and annealing treatment exhibits superhydrophilic characteristic. The complete wetting is due to the spread of water droplets inside the spherical particles on SLM-Ti surface. Fluorinated TiO2 NTAs on SLM-Ti exhibits superhydrophobic characteristic. Water droplets move spontaneously on the horizontal surface with almost no contact angle hysteresis. More importantly, the water contact angle and contact angle hysteresis can be controlled by the fine design of the SLM-Ti anodization process. The process-inherent surface roughness of SLM-Ti seems to present a significant potential for the development of superwetting materials, which can fulfill various technological demands.

Performance of Sprayed PVDF-Al2O3 Composite Coating for Industrial and Civil Applications

Because of their great water repellency, Superhydrophobic coatings have a major impact on a variety of industrial applications. The current study’s key originality is the development of low-cost, stable, superhydrophobic, and corrosion-resistant composite coatings. In the present work, polyvinylidene fluoride (PVDF)/Al2O3 composite coatings were produced using the spray technique to investigate the wettability and corrosion behavior of the coated materials for industrial and civil applications. PVDF was mixed with various concentrations of Al2O3 nanoparticles, and the mixture was sprayed onto steel, aluminum, and glass substrates. The wettability and morphology of the coated surfaces were investigated using the sessile droplet method and scanning electron microscopy, respectively. The corrosion resistance of bare substrates was compared to that of those coated with PVDF alone and those coated with PVDF/Al2O3 nanoparticles using Tafel polarization techniques. The force of adhesion between the coat and the substrates was measured in pounds per square inch. A nanoindentation test was also used to measure the hardness of the coating layer. The PVDF/Al2O3 coated steel showed a significantly higher water contact angle and lower contact angle hysteresis, reaching 157 ± 2° and 7 ± 1°, respectively, compared to the coated aluminum and glass substrates. Corrosion test results showed that the superhydrophobic PVDF/Al2O3 coatings had a much higher corrosion protection efficiency for steel and aluminum than that of the PVDF ones. The PVDF/Al2O3 coated substrates showed moderate but still acceptable adhesion between the coating layer and the substrates. Moreover, the PVDF/Al2O3 coatings had much better mechanical properties than the PVDF only coatings. Such type of coating could be a promising candidate for possible industrial and civil applications.

Self-healing superhydrophobic A-SiO2/N-TiO2@HDTMS coating with self-cleaning property

The superhydrophobic self-cleaning coatings with reversible adhesion to water droplets have attracted much attention due to the unique and wonderful self-cleaning performance. In this paper, amorphous SiO2 microspheres (A-SiO2) and nano-TiO2 particles (N-TiO2) were used to fabricate A-SiO2/N-TiO2 composites by wet grinding, and then they were modified with Hexadecyltrimethoxysilane (HDTMS) and sprayed onto the surface of substrate to obtain a A-SiO2/N-TiO2@HDTMS coating. The water contact angle (WCA) and contact angle hysteresis (CAH) of the coating were 157.2° and 2.7°, respectively. After UV irradiation, the WCA decreased to 140.9°, and water droplets stuck onto the coating surface even the coating was turned upside down. Significantly, the coating surface returned to its original superhydrophobic state after dark storage for 8 h, showing a self-healing property. Furthermore, methyl orange solution was degraded by the as-prepared coating under UV irradiation. Moreover, the as-prepared coating maintained its self-cleaning performance after being placed outdoors for 3 months, exhibiting the potential to be used outdoors for a long time. The as-prepared coating not only has excellent properties but also the advantages of environmental protection. Therefore, this research provides an advanced method to prepare self-cleaning coatings environmentally.

Hydrothermal facile fabrication of superhydrophobic magnetic nanospiky nickel wires: Optimization via statistical design

In the present research, novel superhydrophobic magnetic nanospiky nickel wires via a controlled one-step hydrothermal method were fabricated using Taguchi L16 statistical design. The effects of independent factors including concentration of NiCl2 .6H2O (50-125 mM), the concentration of N2H4.H2O (450-1650 mM), reaction temperature (80-100 ºC), and reaction time (6-12 h) on the wettability properties of octadecyl trichlorosilane (ODTS)-modified samples were investigated. Based on ANOVA and the main effect analyses, despite all factors affecting the wettability response, hydrazine solution concentration with a contribution percent of 47.22% had the most significant effect on the samples' hydrophobicity and growth mechanism as a reducing agent and bridging bidentate ligand. Under the predicted optimum conditions (A1¯,B3¯,C2¯,D2¯), the water contact angle (WCA) and contact angle hysteresis (CAH) were 162.78°±2.4º and 4.32°±0.9º, respectively. Morphological aspects and chemical composition of the as-prepared samples were studied using X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy-Dispersive X-ray spectroscopy (EDX), and Vibrating Sample Magnetometer (VSM) analyses. According to the FESEM images, the length and spike diameters were ranged 500-800 nm and 50-90 nm, respectively. The conical nanospikes' growth on the nickel wires was not dependent on the external magnetic field. It just promoted the formation of straight wires along the present magnetic field. The coercivity (Hc) and remnant magnetism (Mr) in the presence of the magnetic field were 103.077 Oe and 7.80 emu/g, respectively, due to the crystallite arrangement anisotropy.

Solution Crystallization of Polycarbonate Surfaces for Hydrophobic State: Water Droplet Dynamics and Life Cycle Assessment towards Self-Cleaning Applications.

Polycarbonate sheets are optically transparent and have the potential to be used as one of the cover materials for PV applications. Solution treatment of polycarbonate surfaces enables to create surface texture topology giving rise to a hydrophobic state, which is favorable for self-cleaning applications. In the present study, hydrophobization of polycarbonate surface is investigated via crystallization of surface by a one-step process. The influence of texture topology, which is created via crystallization, on water droplet mobility and optical transmittance is examined. Findings revealed that solution treatment, using acetone, results in crystallized polycarbonate surfaces with a hydrophobic state. Depending on the treatment duration, the texture characteristics of crystallized surface change while influencing the water contact angle hysteresis. This in turn affects the droplet mobility over the inclined crystallized surface and alters the UV visible transmittance. Moreover, the droplet mobility improves and dust mitigation rates from the treated surface increase as the solution treatment duration are reduced to 2 min. Oil impregnated samples result in improved UV visible transmittance; however, droplet motion changes from rolling to sliding over the surface. A sliding water droplet enables the removal of the dust particles from the oil-impregnated sample surface.

Macroporous Superhydrophobic Coatings with Switchable Wettability Enabled by Smart Shape Memory Polymers

AbstractHere, a facile bottom‐up nanofabrication technology for making smart superhydrophobic coatings with switchable wettability and tunable optical properties by integrating shape memory polymers (SMPs) with templated macroporous photonic crystals is reported. Thermoresponsive shape memory efforts exhibited by a polyurethane‐based shape memory copolymer enable reversible microstructural transitions between a “memorized” permanent configuration composing of highly ordered arrays of macropores and a temporary deformed structure with collapsed macropores. The unique macroporous SMP photonic crystal arrays with large surface roughness can entrap a large portion of air in the interconnecting macropores, resulting in superior superhydrophobic properties including high apparent water contact angle (CA > 160°) and low CA hysteresis. Importantly, the shape memory‐enabled microstructural transitions lead to drastic wettability switching from superhydrophobic (CA > 160°) to hydrophobic (CA ≈ 110°) or from oleophobic (CA ≈139° for hexadecane) to oleophilic (CA ≈ 80°). The large CA tunability (>50°) coupled with the simultaneous color change from shining iridescence to colorless associated with the same microstructural transition can not only provide a noninvasive means for visually indicating the surface wetting states, this favorable coupling between the wetting and optical behaviors of macroporous SMP photonic crystal membranes can also pave the way for developing new tunable nanooptical devices.

Different Approaches to Low-Wettable Materials for Freezing Environments: Design, Performance and Durability

Ice nucleation and accretion leads to multiple problems such as freezing of the streets which can cause traffic collisions or people injuries, and collapse of high voltage power lines leading to black-out and icing of aircraft components, causing major aeronautic accidents. The most widespread strategies for the removal of accumulated ice layers result in most cases being expensive, time-consuming and hazardous for the environment. In this work we present the design of hydrophobic hybrid inorganic-organic coatings via Lotus leaf-like and slippery liquid infused porous surfaces (SLIPS) approaches with reduced, lasting wetting performance in cold environments. Static and dynamic wetting behavior was evaluated at room and sub-zero temperatures. The main target was the selection of the most suitable design approaches and formulations of coatings to be applied on metals or alloys when the contact time between the droplet and the material surface has to be minimized. In the temperature range from −10 to 0 °C, we report evidence of a stable hydrophobicity and a low water contact angle hysteresis (below 15°) of all the SLIPS developed. The surfaces’ ability to keep their wetting performance unchanged during the freeze/and frost/thaw durability cycles stood out as a key issue for further development at larger scale.