Volumes Of Polymethylmethacrylate Research Articles

In vitro mechanical analysis of X-shaped femoroplasty with polymethyl methacrylate boundary a fall on the greater trochanter,

To evaluate with mechanical testing (MT) using synthetic femurs, an X-shaped femoroplasty technique with polymethyl methacrylate (PMMA), analyzing the results applied to the prophylaxis of proximal femur (PF) fractures caused by low-energy trauma. MT was performed simulating a fall on the greater trochanter, using fifteen Sawbones™ models. They were divided into three experimental groups (n = 5): control (DP) group, drilled without augmentation (DWA) group, and X-shaped augmentation (DX) group. Maximum load, stiffness, absorbed energy and displacement were analyzed primarily in all groups; and secondarily then, morphology and fracture type were verified in all groups while PMMA volume, temperature and time polymerization were analyzed only in the DX group. The MT results obtained for synthetic models respectively in the DP, DWA, and DX groups were: mean maximum load (5562.0 ± 464.8) N, (4798.0 ± 121.2) N, and (7132.0 ± 206.9) N; mean stiffness values (673 ± 64.34) N/mm, (636 ± 8.7) N/mm, and (738 ± 17.13) N/mm, and mean absorbed energy values (36,203 ± 3819) N.mm, (27,617 ± 3011) N.mm, (44,762 ± 3219) N.mm; mean displacement values (13.6 ± 1.45) N, (11.1 ± 0.5) N, and (13.2 ± 0.69) N. The mean volume, temperature reached during filling in the DX group were 9.8 mL, 42.54ºC with 1ʹ 56ʺ of polymerization. The fracture types were similar between the DP and DWA groups, affecting the trochanteric region, as distinctly to those in the DX group, which were restricted to the femoral neck. The values obtained in MT showed statistical significance when analyzed by one-way ANOVA (5%) for maximum load, stiffness, and absorbed energy between groups. In conclusion, X-shaped PMMA augmentation presents a protective biomechanical characteristic against PF fractures generated in synthetic models by boundary a fall on the greater trochanter.

Influence of cement-augmented pedicle screws with different volumes of polymethylmethacrylate in osteoporotic lumbar vertebrae over the adjacent segments: a 3D finite element analysis

BackgroundPolymethylmethacrylate (PMMA) is commonly used for cement-augmented pedicle screw instrumentation (CAPSI) to improve the fixation stability and reduce the risk of screw loosening in the osteoporotic thoracolumbar spine. Biomechanical researches have shown that various dose of cement (1-3 ml) can be injected to enhance screw stability. To date, there have been no studies on the relationship between adjacent segment degeneration and the volume of PMMA. This study aimed to explore the influence of CAPSI with different volumes of PMMA in osteoporotic lumbar vertebrae over adjacent segments by using finite element analysis.MethodsSeven different finite element models were reconstructed and simulated under different loading conditions, including (1) an intact model, (2) three single-level CAPSI models with different volumes of PMMA (1, 1.73, and 2.5 ml), and (3) three double-level CAPSI models with different volumes of PMMA (1, 1.73, and 2.5 ml). To improve the accuracy of the finite element analysis, the models of the injectable pedicle screw and bone cement were created by using a three-dimensional scanning machine and the CAPSI patient’s CT data, respectively. The range of motion (ROM), the stress of intervertebral discs, and the stress of facet in the adjacent segment were comparatively analyzed among the different models.ResultsThe ROMs of the different segments were compared with experimental data, with good agreement under the different load conditions (21.3°, 13.55°, 13.99°, and 6.11° in flexion, extension, bending, and rotation at L3-S1 level, respectively). Compared with the intact model, the ROM, disc stresses, and facet stress in adjacent segments were found to be higher in the six operative models. Otherwise, with a larger volume of PMMA injected, the ROM, disc stresses, and facet stress slightly increased at the adjacent segment. However, the differences were insignificant with the biggest difference less than 3.8%.ConclusionsCAPSI could increase the incidence of disk degeneration in the adjacent segment, while within a certain range, different volumes of PMMA provided an approximate impact over the adjacent segment degeneration.

Biomechanical Test after Hip Cannulated Screw Removal (in vitro Analysis).

Objective This study aims to evaluate, through biomechanical tests, the resistance and energy required for proximal femoral fracture in synthetic bones after removing cannulated screws shaped as an inverted triangle, comparing the obtained results to those of a reinforcement technique with polymethylmethacrylate (PMMA) as bone cement. Methods Twenty synthetic bones were used: 10 units for the control group (CG), 5 units for the test group without reinforcement (TGW/O), and 5 units for the test group using a reinforcement technique with PMMA (TGW). The biomechanical analysis simulated a fall on the large trochanter using a servo-hydraulic machine. Results All TGW/O and CG specimens had a basicervical fracture. Three TGW specimens presented a basicervical fracture, and two suffered a fracture near the fixation point of the device (femoral diaphyseal region), with one of them being associated with a femoral neck fracture. A mean PMMA volume of 8.2 mL was used to fill the 3 screw holes in the TGW group. According to the one-way analysis of variance (ANOVA) and the Tukey multiple comparisons tests at a 5% level, the TGW presented a statistically significant difference when compared with the other groups in all parameters: maximal load ( p = 0.001) and energy until fracture ( p = 0.0001). Conclusion The simple removal of the cannulated screws did not reduce significantly the maximum load and energy for fracture occurrence, but the proximal femoral reinforcement with PMMA significantly increased these parameters, modifying the fracture pattern.

Biodegradation patterns of injected composite bone cements in porcine vertebral bodies

Background: For vertebroplasty, newly synthesized bone cements are proposed to replace traditional polymethylmethacrylate (PMMA). Most inventors initially evaluated these newly developed cements in animal spine models. However, even these time- and work-consuming histological inspections performed meticulously by experienced hands, there are still lots of specimen lost during the processing procedures. Although the histological sections can reveal new bone formations and surrounding tissue reactions to implanted materials, it is difficult to identify the degradation processes of the injected cement. In fact, there is no standard method to quantify the volume changes of injected substitutes postoperation. Methods: Previously, we developed two new biodegradable cements and evaluated performances in fixed-volume and fixed-shaped holes in vertebral bodies of porcine lumbar spine. The animals were sacrificed and the retrieved spines were analyzed after 3 and 6 months. Herein, we further used computed tomography (CT) and three-dimensional CT (3D-CT) to quantitate volumes and biodegradation of cements inside vertebral bodies after previous attestation of CT findings. Exteriors of controls and injected materials were reconstructed with different Hounsfield units (HU); changes of HU as well as cement volumes were later calculated. Results: The results revealed that the volumes and shapes of these biodegradable cements can be determined by 3D-CT. After meticulous comparisons among gross specimens, histologies, and CT images, the different patterns observed in CT implied consistency among all three observations. Gradual reductions of HU and volumes of newly synthesized cements showed the degradability. Meanwhile, consistent HU and volumes of PMMA meant its inertness. Conclusion: CT imaging may be a preliminary, quantitative, and liable way for evaluating injectable bone cements in the vertebral bodies.

Biomechanical study of injectable hollow pedicle screws for PMMA augmentation in severely osteoporotic lumbar vertebrae: effect of PMMA distribution and volume on screw stability.

OBJECTIVEThe purpose of this study was to compare stability of injectable hollow pedicle screws with different numbers of holes using different volumes of polymethylmethacrylate (PMMA) in severely osteoporotic lumbar vertebrae and analyze the relationship between screw stability and distribution and volume of PMMA.METHODSForty-eight severely osteoporotic cadaveric lumbar vertebrae were randomly divided into 3 groups-groups A, B, and C (16 vertebrae per group). The screws used in group A had 4 holes (2 pairs of holes, with the second hole of each pair placed 180° further along the thread than the first). The screws used in group B had 6 holes (3 pairs of holes, placed with the same 180° difference in position). Unmodified conventional screws were used in group C. Each group was randomly divided into subgroups 0, 1, 2, and 3, with different volumes of PMMA used in each subgroup. Type A and B pedicle screws were directly inserted into the vertebrae in groups A and B, respectively, and then different volumes of PMMA were injected through the screws into the vertebrae in subgroups 0, 1, 2, and 3. The pilot hole was filled with different volumes of PMMA followed by insertion of screws in groups C0, C1, C2, and C3. Distributions of PMMA were evaluated radiographically, and axial pull-out tests were performed to measure the maximum axial pullout strength (Fmax).RESULTSRadiographic examination revealed that PMMA surrounded the anterior third of the screws in the vertebral bodies (VBs) in groups A1, A2, and A3; the middle third of screws in the junction area of the vertebral body (VB) and pedicle in groups B1, B2, and B3; and the full length of screws evenly in both VB and pedicle in groups C1, C2, and C3. In addition, in groups A3 and B3, PMMA from each of the screws (left and right) was in contact with PMMA from the other screw and the PMMA was closer to the posterior wall and pedicle than in groups A1, A2, B1, and B2. One instance of PMMA leakage was found (in group B3). Two-way analysis of variance revealed that 2 factors-distribution and volume of PMMA-significantly influenced Fmax (p < 0.05) but that they were not significantly correlated (p = 0.078). The Fmax values in groups in which screws were augmented with PMMA were significantly better than those in groups in which no PMMA was used (p < 0.05).CONCLUSIONSPMMA can significantly improve stability of different injectable pedicle screws in severely osteoporotic lumbar vertebrae, and screw stability is significantly correlated with distribution and volume of PMMA. The closer the PMMA is to the pedicle and the greater the quantity of injected PMMA used, the greater the pedicle screw stability is. Injection of 3.0 mL PMMA through screws with 4 holes (2 pair of holes, with the screws in each pair placed on opposite sides of the screw) produces optimal stability in severely osteoporotic lumbar vertebrae.

Biomechanical comparative study of the stability of injectable pedicle screws with different lateral holes augmented with different volumes of polymethylmethacrylate in osteoporotic lumbar vertebrae

Background ContextPolymethylmethacrylate (PMMA) is widely used for pedicle screw augmentation in osteoporosis. Until now, there had been no studies of the relationship between screw stability and the distribution and volume of PMMA. PurposeThe objective of this study was to analyze the relationship between screw stability and the distribution pattern and injected volume of PMMA. Study DesignThis is a biomechanical comparison of injectable pedicle screws with different lateral holes augmented with different volumes of PMMA in cadaveric osteoporotic lumbar vertebrae. MethodsForty-eight osteoporotic lumbar vertebrae were randomly divided into Groups A, B, and C with different pedicle screws (16 vertebrae in each group), and then each group was randomly divided into Subgroups 0, 1, 2, and 3 with different volumes of PMMA (four vertebra with eight pedicles in each subgroup). A pilot hole was prepared in advance using the same method in all samples. Type A and type B pedicle screws were directly inserted into vertebrae in Groups A and B, respectively, and then different volumes of PMMA (0, 1.0, 1.5, and 2.0 mL) were injected through the screws and into vertebrae in Subgroups 0, 1, 2, and 3. The pilot holes were filled with different volumes of PMMA (0, 1.0, 1.5, and 2.0 mL), and then the screws were inserted in Groups C0, C1, C2, and C3. Screw position and distribution of PMMA were evaluated radiographically, and axial pullout tests were performed to measure maximum axial pullout strength (Fmax). ResultsPolymethylmethacrylate surrounded the anterior one-third of screws in the vertebral body in Groups A1, A2, and A3; the middle one-third of screws in the junction area of the vertebral body and the pedicle in Groups B1, B2, and B3; and the full length of screws evenly in both the vertebral body and the pedicle in Groups C1, C2, and C3. There was no malpositioning of screws or leakage of PMMA in any sample. Two-way analysis of variance revealed that two factors—distribution and volume of PMMA—significantly influenced Fmax (p<.05) but that they were not significantly correlated (p=.088). Fmax values in groups using augmentation with PMMA values significantly improved compared with those in groups without PMMA (p<.05). ConclusionsPolymethylmethacrylate can significantly enhance the stability of different injectable pedicle screws in osteoporotic lumbar vertebrae, and screw stability is significantly correlated with the distribution pattern and the injected volume of PMMA. The closer the PMMA to the pedicle and the greater the quantity of injected PMMA, the greater is the pedicle screw stability. Injection of 2.0 mL of PMMA through screws with four lateral 180° holes or of 1.0 mL of PMMA through screws with six lateral 180° holes increases the stability of pedicle screws.

Biomechanical comparison of pedicle screw augmented with different volumes of polymethylmethacrylate in osteoporotic and severely osteoporotic cadaveric lumbar vertebrae: an experimental study

Background ContextPolymethylmethacrylate (PMMA) is widely used for pedicle screw augmentation in osteoporosis. Intriguingly, there have been no biomechanical comparisons of the stability of pedicle screws augmented with different volumes of PMMA or studies of the relationship between screw stability and volume of PMMA, especially in different degrees of osteoporosis. PurposeThe purposes of the study reported here were to compare screw stability by different volumes of PMMA augmentation, to analyze the relationship between screw stability and PMMA volume, and to make a preliminary determination of the optimum volume of PMMA augmentation for different degrees of osteoporosis. Study DesignThis study is a biomechanical comparison of pedicle screws augmented with various volumes of PMMA in cadaveric lumbar vertebrae. MethodsThirty-six pedicles from 18 osteoporotic lumbar vertebrae were randomly divided into groups A0 through A5, and 36 pedicles from 18 severely osteoporotic lumbar vertebrae were randomly divided into groups B0 through B5. A different volume of PMMA was injected into each one of groups A0 through A5 (0, 0.5, 1.0, 1.5, 2.0, and 2.5 mL, respectively) and into each one of groups B0 through B5 (0, 1.0, 1.5, 2.0, 2.5, and 3.0 mL, respectively), and then pedicle screws were inserted in all vertebrae. After complete solidification of the PMMA, we examined pedicle X-rays, performed axial pullout tests, and determined the maximum axial pullout strength (Fmax) for all samples. ResultsNo PMMA was found around the screws in groups A0 and B0. In groups A1 to A5 and B1 to B5, screws were wrapped by gradually increasing amounts of PMMA. There was no PMMA leakage or screw malpositioning in any samples. The Fmax in groups A1 through A5 increased by 32.40%, 64.42%, 116.02%, 174.07%, and 207.42%, respectively, compared with that in group A0. There were no significant differences in Fmax between groups A0 and A1, A1 and A2, A2 and A3, A3 and A4, and A4 and A5 (p>.05), but there were significant differences in Fmax between any other two groups (p<.05). The Fmax in groups B1 through B5 increased by 23.48%, 48.40%, 106.60%, 134.73%, and 210.04%, respectively, compared with that in group B0. There were no significant differences in Fmax between groups B0 and B1, B0 and B2, B1 and B2, B2 and B3, B3 and B4 (p>.05), but there were significant differences in Fmax between any other two groups (p<.05). There was a significant positive correlation between Fmax and volume of PMMA in both osteoporotic and severely osteoporotic lumbar vertebrae (p<.05). ConclusionsPolymethylmethacrylate can significantly enhance stability of pedicle screws in both osteoporotic and severely osteoporotic lumbar vertebrae. There is a significant positive correlation between screw stability and volume of PMMA. Within a certain range, nevertheless, increasing the volume of PMMA does not significantly improve screw stability. We suggest that 1.5 and 3 mL, respectively, are the volumes of injected PMMA that will optimize pedicle screw stability in osteoporotic and severely osteoporotic lumbar vertebrae.

Biomechanical Comparison of Pedicle Screw Augmented with Different Volumes of Polymethylmethacrylate in Osteoporotic and Severely Osteoporotic Synthetic Bone Blocks in Primary Implantation: An Experimental Study.

This study was designed to compare screw stabilities augmented with different volumes of PMMA and analyze relationship between screw stability and volume of PMMA and optimum volume of PMMA in different bone condition. Osteoporotic and severely osteoporotic synthetic bone blocks were divided into groups A0-A5 and B0-B5, respectively. Different volumes of PMMA were injected in groups A0 to A5 and B0 to B5. Axial pullout tests were performed and F max was measured. F max in groups A1-A5 were all significantly higher than group A0. Except between groups A1 and A2, A3 and A4, and A4 and A5, there were significant differences on F max between any other two groups. F max in groups B1-B5 were all significantly higher than group B0. Except between groups B1 and B2, B2 and B3, and B4 and B5, there were significant differences on F max between any other two groups. There was significantly positive correlation between F max and volume of PMMA in osteoporotic and severely osteoporotic blocks. PMMA can significantly enhance pedicle screw stability in osteoporosis and severe osteoporosis. There were positive correlations between screw stability and volume of PMMA. In this study, injection of 3 mL and 4 mL PMMA was preferred in osteoporotic and severely osteoporotic blocks, respectively.

Potential neurotoxic effects of polymethylmethacrylate during cranioplasty

Cranioplasty for the surgical correction of cranial defects is often performed using polymethyl methacrylate (PMMA), or bone cement. Immediately prior to PMMA application, a liquid monomer form (methylacrylate) and a benzoyl peroxide accelerator are mixed resulting in polymerization, an exothermic reaction during which monomer linking and subsequent formation of solid polymer occur. The potential side effects of residual methylacrylate monomer toxicity and thermal damage of neural tissue during PMMA hardening have been described in various in vitro, animal, and cadaveric studies; however, clinically documented in vivo neurotoxicity in humans attributed to either of the above two mechanisms during PMMA cranioplasty is lacking. We present a series of four patients operated for removal of cerebellopontine angle lesions and two operated for the excision of parieto-occipital tumors who sustained cranial neuropathies and encephalopathies with transient or permanent neurological deficits that could not be attributed to surgical manipulation. We hypothesize that these complications most likely occurred due to thermal damage and/or chemical toxicity from exposure to PMMA during cranioplasty. Our case series indicates that even small volumes of PMMA used for cranioplasty may cause severe side effects related to thermal damage or to exposure of neural tissue to methylacrylate monomer.

Biomechanical effects of bone cement volume on the endplates of augmented vertebral body: a three-dimensional finite element analysis

Background Previous studies have suggested that percutaneous vertebroplasty might alter vertebral stress transfer, leading to adjacent vertebral failure. However, no three-dimensional finite element study so far accounted for the stress distributions on different cement volumes. The purpose of this study was to evaluate the stress distributions on the endplate under different loading conditions after augmentation with various volumes of bone cement. Methods L2-L3 motion segment data were obtained from CT scans of the lumbar spine from a cadaver of a young man who had no abnormal findings on roentgenograms. Three-dimensional model of L2-L3 was established using Mimics software, and finite element model of L2-L3 functional spinal unit (FSU) was established using Ansys10.0 software. For simulating percutaneous vertebral augmentation, polymethylmethacrylate (PMMA) was deposited into the bipedicle of the L2 vertebra. The percentage of PMMA volume varied between 15% and 30%. The stress distributions on the endplate of the augmented vertebral body were calculated under three different loading conditions. Results In general, the stress level monotonically increased with bone cement volume. Under each loading condition, the stress change on the L2 superior and inferior endplates in three kinds of finite element models shows monotonic increase. Compared with the stress-increasing region of the endplate, the central part of the L2 endplate was subject to the greatest stress under three kinds of loading conditions, especially on the superior endplate and under flexion. Conclusions The finite element models of FSU are useful to optimize the planning for vertebroplasty. The bone cement volume might have an influence on the endplate of the augmentation, especially the superior endplate. It should be noted that the optimization of bone cement volume is patient specific; the volume of the bone cement should be based on the size, body mineral density, and stiffness of the vertebrae of individual patients.

Comparative Assessment of Sacral Screw Loosening Augmented with PMMA Versus a Calcium Triglyceride Bone Cement

A calcium triglyceride bone cement (CTBC) was compared with the gold-standard polymethylmethacrylate (PMMA) to assess the stability of augmented sacral screw fixation under cyclic loading. To determine whether CTBC augmentation of a pedicle screw would provide a similar level of fixation in the S1 pedicles compared with PMMA augmentation. Numerous studies have shown the advantages of using PMMA to augment screw fixation; however, its biomechanical properties are not ideal. CTBC offers potential benefits such as being low exothermic, a modulus of elasticity closer to bone, and the potential for osteoconductivity, but its comparative performance in this situation has not been previously evaluated. Six cadaveric sacra were used in this study; 3.0 mL volumes of PMMA (Simplex P) and CTBC (Kryptonite™ Bone Cement) were injected into contralateral screw tracts, with the screw immediately inserted after cement injection. After a 12-hour setting period, the sacrum was potted in a custom fixture and mounted to the frame of a materials testing machine. Alternating flexion and extension bending moments were applied at 1 Hz. Flexion moments were applied starting at 0.5 Nm and increased by 1 Nm after every 1000 cycles until the screw had reached 6° of rotation relative to its starting position. Extension moments were maintained at 0.5 Nm. Screw rotation relative to bone was determined in real time by a custom optical tracking system and was analyzed using two-way repeated-measures analyses of variance (ANOVAs) and post hoc Student-Newman-Keuls tests (α = 0.05). To reach 6° of screw rotation, the PMMA-augmented screw required more loading cycles (15,464 ± 2526 vs. 10,277 ± 1762 cycles; P = 0.006) and a larger applied moment (15.3 ± 2.2 vs. 10.5 ± 1.7 Nm; P = 0.010) than CTBC-augmented screw. The PMMA augmentation provided increased resistance to cyclic loading compared with the CTBC augmentation for sacral pedicle screw fixation, but both augmentations well exceeded previously published findings for nonaugmented screws.

Biomechanics of prophylactic vertebral reinforcement.

The effects of bone cement placement, volume, and bone density on the degree of biomechanical reinforcement on cadaveric vertebral bodies were studied using experimentally calibrated detailed finite element models. To investigate the efficacy of prophylactic vertebroplasty on intact vertebral bodies with respect to biomechanical recovery and fracture risk reduction. Vertebroplasty is a potentially effective fracture prevention treatment, but the risk of complications due to cement leakage must be minimized. Therefore, the least amount of bone cement required to improve vertebral strengths to low fracture risk levels need to be determined. Six different polymethyl methacrylate volumes--1, 2.5, 3.5, 5, 7.5 and 9 cm--were virtually implanted into previously validated vertebral body finite element models, following bipedicular and posterolateral vertebroplasty approaches. Stiffness and fracture load of the treated and untreated vertebral body models under uniaxial compression were determined. Greater augmentation effects were observed for vertebral bodies with average quantitative computed tomography densities below 0.1 g/cm injected with polymethyl methacrylate volumes higher than 20% compared to lower injection volumes and higher bone densities, as well as for the bipedicular approach versus posterolateral. Vertebral bodies at high risk of fracture required at least 20% fill of polymethyl methacrylate to improve the mechanical integrity of vertebral bodies to low fracture risk levels, whereas 5% to 15% polymethyl methacrylate volumes were needed for the medium-risk vertebral bodies. Prophylactic vertebroplasty can be effective in reducing fracture risk. However, for the polymethyl methacrylate volume (20%) required for the successful reinforcement of high-risk vertebral bodies, the risk of complications will be as high as that for current vertebroplasty procedure for fracture repair. Therefore, alternative materials have to be investigated for prophylactic vertebroplasty. Furthermore, bipedicular vertebroplasty is the recommended approach due to its higher strengthening effect and easier surgical access than the posterolateral case.

척추성형술을 위한 의료 영상 시스템의 설계 및 개발

척추에 대한 외과수술은 신경조직을 손상하지 않아야 하기 때문에 수술 절차가 신중하게 계획되고 고도의 정밀을 요구한다. 척추성형술(verte-broplasty)은 골다공증으로 인한 척추의 골절을 치료하기 위해 제안된 비교적 새로운 외과적인 수술방법으로 최소침습적인 수술 기법으로 피부를 통하여 골절된 척추부위에 구멍을 내고 그곳에 PMMA(polymethylmethacrylate)라 불리는 골시멘트(bone cement)를 주입하여 치료하는 방법이다. 최근의 연구결과, 수술 후 즉각적인 고통의 경감을 가져오며, 골다공증으로 인한 골절부위에 강도가 강한 골시멘트를 주입하게 됨으로써 골다공증 척추체에 구조적인 안정성을 제공해 주는 것으로 알려져 있다. 수술 후 발생하는 합병증의 대부분은 과도한 골시멘트의 주입으로 인한 것으로 알려져 있으며, 따라서 척추성형술의 치료에 가장 중요한 요인은 주입한 골시멘트의 양을 조절하는 것이다. 이에 본 연구에서는 환자의 컴퓨터단층촬영(computer tomography)을 통하여 획득한 영상을 토대로 척추성형술 시술시 필요한 의료 영상 시스템을 설계 및 개발하고, 텍스처 분석을 통하여 개개인의 환자에게 필요한 골시멘트의 양을 계산하는 알고리즘을 개발하여 이를 실제 환자의 시술시에 적용해 보았다. 결과적으로 본 시스템은 척추성형술시에 최적의 골시멘트의 양을 예측할 수 있었으며, 정형외과의 다른 부위의 수술시에도 적용가능성을 확인할 수 있었다. Since surgical treatment of the spine should overcome neurological compromises, the operative procedures need to be carefully planned and carried out with high degree of precision. Percutaneous vertebroplasty is a surgical procedure that was introduced for the treatment of compression fracture of the vertebrae. This procedure includes puncturing vertebrae and filling with polymethylmethacrylate (PMMA). Recent studies have shown that the procedure could provide structural reinforcement for the osteoporotic vertebrae while being minimally invasive and safe with immediate relief of pain. However, failures of treatment due to excessive PMMA volume injection have been reported as one of complications in vertebroplasty. It is believed that the control of PMMA volume is one of the most critical factors that can reduce the incidence of complications. Therefore, clinical success of vertebroplasty can be dependent on the volume of PMMA injection for a given patient. In this study, the optimal volume of PMMA injection for vertebroplasty was predicted based on the image analysis of a given patient.

Midterm outcome after vertebroplasty: predictive value of technical and patient-related factors.

To evaluate different types of polymethylmethacrylate (PMMA) leakage and patient-related factors in relation to clinical midterm (1-24-month) outcome after vertebroplasty. Standardized four-view radiographs obtained during 363 vertebroplasties in 181 treatment sessions in 152 patients were reviewed (121 patients with osteoporotic fractures, 30 with malignant disease, and one with hemangioma). Four types of PMMA leakage and other potential predictors (patient age and sex, treated region, number of vertebral levels injected, preprocedural pain, PMMA volume per vertebra) were related to postprocedural pain response and midterm outcome after vertebroplasty. chi2 and Kruskal-Wallis tests were used for statistical analysis. The mean follow-up period was 8.8 months (range, 1-24 months). At the time of discharge after the procedure, pain was absent after 106 of the 181 sessions (58.5%), better after 50 (27.6%), and the same after 25 (13.8%). In 258 of the 363 treated vertebral levels, at least one type of leakage was found. None of the evaluated factors were related significantly to postprocedural pain response, including PMMA leakage. Pain response at midterm outcome was strongly related to postprocedural treatment success, however (P <.001). Small to moderate amounts of PMMA may escape from the vertebral body with no significant effect on therapeutic success. Immediate postprocedural pain relief is the best predictor of midterm clinical outcome after vertebroplasty.

Proposal of a computerized algorithm for continuous wave CO2 laser on-line control during orthopaedic surgery. Phase I: Theoretical introduction and firstin vitro trials

New data obtained from treating polymethylmethacrylate (PMMA) with a non-moving cw- 10 watt-CO2 laser-beam focused at 2.5'', 5'', 7.5'' and 15.75'' are presented. . The final equations R(tc) and Z(tc) for each focal length are proposed. A very interesting correlation between the focal lengths in use and the integrated values of R and Z between 0 and 2 sec has been identified and discussed. This result has been used as basis to define a convenient operative protocol to follow during the planning phase of critical osteotomies or bone cement removal operations using a continuous-wave CO2 laser-beam set to any output power and focused by a set of most common, moving or non-moving focal lengths placed on the operating area. With a simple equation, it is possible to compare craters obtained with moving and non-moving laser-beams at different operative conditions between 0 and 2 sec, time interval which covers the majority of cases. A value of 2.3 +/- 0.1 between ablated volumes of PMMA and bone tissue has been identified. Several case studies regarding orthopaedic procedures from Literature are here reported and compared to the present LCA model. The computerized on-line flow of information for the laser-beam optimization and safety control is also described. Finally, a method for the simultaneous data collection from several operating rooms via a Local Area Network (LAN-Industry Standard IEEE) onto a central data base for later consultation is proposed in its general design.