Visible Irradiation Research Articles

Preparation of Cu/Cu2O/BC and Its Performance in Adsorption-Photocatalytic Degradation of Methyl Orange in Water.

In this study, we prepared a low-cost novel Cu/Cu2O/BC nanocomposite visible-light photocatalyst by the impregnation method using CuSO4·5H2O and rice husk biochar (BC) as raw materials and Na2S2O4 as a single reductant to improve the stability and dispersion of the Cu/Cu2O nanoparticles, in order to solve their aggregation tendency during photocatalysis. The morphology and structure of the Cu/Cu2O/BC were characterized using various analytical and spectroscopic techniques. The photocatalytic effect and cyclic stability of the synthesized photocatalyst on methyl orange (MO) removal were investigated under visible light radiation and various parameter conditions, including the mass ratio of BC to Cu/Cu2O, initial MO concentration, pH, temperature, and catalyst dosage. The results show that the synthesized Cu/Cu2O/BC nanocomposite composed of Cu/Cu2O spherical particles was loaded on the BC carrier, which has better stability and dispersion. The best adsorption-photocatalytic effect of the Cu/Cu2O/BC is exhibited when the mass ratio of BC to Cu/Cu2O is 0.2. A total of 100 mg of Cu/Cu2O/BC can remove 95% of the MO and 88.26% of the COD in the aqueous solution at pH = 6, T = 25 °C, and an initial MO concentration of 100 mg/L. After five cycles of degradation, the MO degradation rate in the sample can still remain at 78.41%. Both the quasi-secondary kinetic model and the Langmuir isothermal adsorption model describe the adsorption process. Additionally, the thermodynamic analysis demonstrates that the photocatalytic process follows the quasi-primary kinetic model and that the removal process is of spontaneous heat absorption. The photocatalyst described in this paper offers a cost-effective, easily prepared, and visible-light-responsive solution for water pollution treatment.

Synergistic integration of metallic Bi and defective TiO2 for enhanced photocatalytic NO removal

The construction of hybrid catalysts is an effective method to enhance catalytic performance, but research on the positioning of the load is limited. In this study, we synthesized two photocatalytic materials by controlling the bismuth-titanium ratio and the site value of Bi modification in the catalyst. The surface-modified photocatalyst, namely 1:0.9 Bi/TiO2, exhibits a photocatalytic efficiency of 68.9 % for the abatement of ppb-level NO in the presence of visible irradiation. This efficiency was significantly superior to that of the corresponding one-step synthesized Bi/TiO2 (48.7 %) and the TiO2 (18.6 %). Furthermore, it promotes nitrate formation and suppresses the generation of toxic NO2. Capture experiments indicate that the same active species are involved in both surface-loaded and uniformly loaded catalysts. The differences in their performance can be attributed to the higher vacancy concentration in the surface-loaded catalysts and the different local coordination environments of vacancies in the catalysts, altering the adsorption capability of oxygen molecules. This work offers fresh perspectives for the generation of efficient photocatalysts.

Instability monitoring of molten pool in pure copper laser welding based on a multi-scale cascade model and spatial optical signals

During laser welding of pure copper, instabilities such as violent molten pool oscillation, large spatters, and melt ejection severely damage weld quality, which are caused by copper’s high reflectivity on commonly used infrared laser. The seriously unstable molten pool and keyhole and complicated laser-material interactions result in complex process signal emission waveforms, adding to the difficulties in process stability monitoring tasks. In this work, to break down different contents in the complex signals and deeply analyzing signal-process relation, combinative spatial optical sensor system was designed, and time-frequency signal analysis in multi-scale windows was performed. It was found that the infrared radiation at the front and end side of molten pool indicates the oscillation behavior of liquid metal surface, and the signal fluctuation patterns of visible radiation from different height of metal vapor varied when meeting severe instability like melt ejections. Signal features were extracted based on the understanding of process mechanism and signal behaviors. A cascade model combining Artificial Neural Network (ANN) and Support Vector Machine (SVM) was introduced to predict weld seam quality, where the ANN model focused on short-time stability status perception and the SVM model was used to decide macroscopic seam formation defects based on combining outputs of the ANN model in a long-term sampling window. Application results showed that the recognition accuracy of pit was 100 % and the accuracy of uneven toe reached 86.3 %. The multi-source signals of unstable molten pool recognized by the cascade model were summarized. The evolution process of copper molten pool ejection was revealed.

Tailoring photocatalytic performance: Lanthanum doping in nickel oxide for efficient degradation of some industrial cationic dyes in visible light radiation

Metal oxide nanoparticles have emerged as an important component in heterogeneous photocatalysis, which uses light-induced reactions on the surface of a catalyst to drive chemical transformations. The improved photocatalytic activity of lanthanum-doped metal oxide nanoparticles has been the subject of research due to their special qualities, which include enhanced photocatalytic performance, stability and absorption of visible light. This study involves co-precipitation approach to synthesize nickel oxide nanoparticles and nickel oxide nanoparticles doped with lanthanum. The nanoparticles were determined using UV-Visible absorption spectrophotometry, X-ray diffraction spectroscopy, Energy-disperse spectroscopy, Photoluminescence spectroscopy and Field emission scanning electron microscopy. For the photodegradation of malachite green and rhodamine B dyes, synthesized nanoparticles were employed as photocatalysts. Compared to pure NiO, the photochemical activity of 4 % Lanthanum-doped NiO was higher. The degrading efficiency of 4 % La-doped NiO is 89 % effective towards rhodamine B and 87 % for malachite green. In addition, entrapment was done to identify primary active species responsible for photocatalytic activity. The present study likely provides new insights and novelty into the photocatalytic mechanisms at play, including how lanthanum doping affects the generation and dynamics of reactive oxygen species (ROS) like hydroxyl radicals and superoxide anions, which are responsible for the breakdown of dye molecules.

SnO2-TiO2 materials for photocatalytic degradation of cationic dye under UV and visible light and a chitosan composite film investigation

The possibility of SnO2 incorporation and immobilization as films forming composites opens new perspectives for TiO2 to profit visible light and to facilitate the photocatalytic process, respectively. In this study, 0 %, 1 % and 10 % wt. of SnO2 was incorporated into TiO2 (SnO2-TiO2) by coprecipitation in a sol-gel method by ammonia addition, followed for calcination at 500 °C. The photocatalysts were characterized by N2 adsorption-desorption, FTIR spectroscopy, XRD Rietveld refinement, TG-DTG, SEM-EDS, DRS and elemental analysis. The performance of all solids was evaluated in the photocatalytic degradation of the cationic dye methylene blue in aqueous phase, under visible and UV irradiation, at 25 °C for 2 h. The results showed that the incorporation of Sn into TiO2 improved the textural properties and decreased the bandgap. All solids presented only TiO2 typical diffractograms, with anatase as the main phase, but catalyst with 10 % SnO2 presented also brookite phase, inferring that Sn atoms were incorporated into TiO2 structure, corroborated by MEV results. All tin-based photocatalysts show high activity under UV and visible light, with the 10 % SnO2 material reaching 83 % and 88 % degradation after 2 h under UV and visible radiation, respectively. This material was tested as an immobilized film, achieving 14 % of decolorization, and the reuse was also evaluated. Our investigation demonstrates that SnO2-TiO2 catalysts could be used to decompose a dye under UV and Visible light as powder in a batch reactor and immobilized as a composite film with chitosan, that opens new perspectives to facilitate the application using solar light.

Extremely Long-Lived Charge Donor States Formed by Visible Irradiation of Quantum Dots.

Using cyclic voltammetry under illumination, we recently demonstrated that CdS quantum dots (QDs) form charge donor states that live for at least several minutes after illumination ends, ∼12 orders of magnitude longer than expected for free carriers. This time scale suggests that the conventionally accepted mechanism of charge transfer, wherein charges directly transfer to an acceptor following exciton dissociation, cannot be complete. Because of these long time scales, this unconventional pathway is not readily observed using time-resolved spectroscopy to probe charge transfer dynamics. Here, we investigated the chemical nature of these charge donor states using cyclic voltammetry under illumination coupled with NMR spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and optical spectroscopy. Our data reveal that charges are stored locally rather than as free carriers, and the number of charges stored is dependent on the QD surface ligation and stoichiometry. Altogether, our results confirm that electrons are stored at ligated surface Cd, these sites are competent charge donors, and this storage is charge balanced by X-type ligand desorption. We found that charge storage occurs in every QD system studied, including CdS, CdSe, and InP capped with carboxylate and phosphonate ligands.

Platinum nanoparticles decorated TiO2 nanotubes for VOCs and bacteria removal in simulated real condition: Effect of the deposition method on the photocatalytic degradation process efficiency

The incorporation of noble metals onto TiO2 nanostructure is considered as a promoting method to enhance the photocatalytic degradation of pollutant in air treatment process. In this study, highly organized TiO2 nanotubes (NTs) were grown by the anodization method of Titanium substrates. The TiO2-NTs were successfully decorated by platinum (Pt) nanoparticles (NPs) using two different deposition methods: (1) electrodeposition and (2) photodeposition.We explore the impact of different deposition methods on the morphology of Pt nanoparticles (NPs) dispersed onto TiO2 nanotubes and the optical characteristics of Pt-TiO2 nanocomposites, investigating their efficacy in photocatalytic degradation We investigate the effect of varying the deposition method on the morphology of Pt-NPs dispersed onto TiO2 nanotubes and the optical properties of the Pt-TiO2 nanocomposites and their efficient photocatalytic activity degradation against Volatile Organic Compounds (VOCs) and bacteria. Scanning and Transmission Electron Microscopy (SEM and TEM) reveal a nanotubular TiO2 anatase structure adorned with Pt NPs, with the quantity and size of NPs contingent upon the deposition technique employed. The photoluminescence (PL) spectra demonstrate that the Pt/TiO2 heterojunction facilitates the separation of photogenerated charges, thereby diminishing carrier recombination rates. To point out the effect of Pt NPS, both pure TiO2 and Pt/TiO2 heterojunction were tested in the photodegradation of Ethyl Acetate (EA). The Pt/TiO2 heterojunction exhibits superior photocatalytic performance compared to TiO2 in EA degradation, regardless of the Pt deposition method employed. Optimal results are achieved with 120 s of Pt electrodeposition and 3 h of Pt photodeposition under visible irradiation, yielding kinetic constants of approximately 0.245 and 0.195 mg.m−3.s−1, respectively, underscoring the pivotal role of the platinum deposition method in pollutant photodegradation. Respectively simultaneous removal of EA and bacteria (Escherichia coli) was tested using Pt and non-Pt decorated TiO2 NTs. We attributed a total degradation of the bacteria after 180 min using the two efficient photocatalysts Electro 120 s and Photo 3 h compared to 60 % of degradation using pure TiO2 nanotubes.

In Situ Photoreversible Tuning of Chemical Interface Damping in Single Gold Nanorods Through Cucurbit[8]uril-Based Host-Guest Interactions.

Chemical interface damping (CID) is a recently proposed plasmon-damping pathway based on the interfacial hot-electron transfer from metal to adsorbate molecules. However, the in situ reversible tuning of CID in single gold nanorods (AuNRs) has remained a considerable challenge. In this study, we used total internal reflection scattering microscopy and spectroscopy to investigate the CID induced by p-aminoazobenzene (p-AAB), which has fast photoisomerization characteristics, attached to single AuNRs. We demonstrated the in situ reversible tuning of CID in single AuNRs by switching between ultraviolet (UV, 365 nm) and visible (vis, 465 nm) irradiation to induce photoresponsive structural conversions between the cis and trans forms of p-AAB in ethanol, leading to different lowest unoccupied molecular orbital (LUMO) energies for both forms. The localized surface plasmon resonance (LSPR) line width was wide under vis irradiation but narrow under UV irradiation, indicating that hot electrons are more efficiently transferred to trans-p-AAB with a low LUMO energy level. We further investigated the in situ photoreversible tuning of CID by manipulating supramolecular host-guest interactions between cucurbit[8]uril (CB[8]) and p-AAB in the single AuNRs. Additionally, real-time in situ reversible tuning of CID in single AuNRs was achieved through photonic switching of the cis-trans forms of p-AAB inside CB[8]. The LSPR line width was narrow under vis irradiation but gradually widened under UV irradiation before narrowing again upon returning to vis irradiation, unlike the case with p-AAB only. These results can be ascribed to the fact that cis-p-AAB completely encapsulated within CB[8] in water is thermodynamically more favorable than trans-p-AAB. Therefore, we have discovered a new strategy for tuning the CID by performing p-AAB photoisomerization and adjusting the wavelength of incident light in single AuNRs. In addition, this study demonstrates that CID can be effectively applied to the development of biosensors to detect guest molecules and their structural changes inside the cavity of CB[8] in single AuNRs.

Photoacoustic Spectroscopy of Titanium Dioxide, Niobium Pentoxide, Titanium:Niobium, and Ruthenium-Modified Oxides Synthesized Using Sol-Gel Methodology.

The aim of this work was the development and morphological/chemical, spectroscopic, and structural characterization of titanium dioxide, niobium pentoxide, and titanium:niobium (Ti:Nb) oxides, as well as materials modified with ruthenium (Ru) with the purpose of providing improvement in photoactivation capacity with visible sunlight radiation. The new materials synthesized using the sol-gel methodology were characterized using the following techniques: scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), photoacoustic spectroscopy (PAS), and X-ray diffraction (XRD). The SEM-EDS analyses showed the high purity of the bases, and the modified samples showed the adsorption of ruthenium on the surface with the crystals' formation and visible agglomerates for higher calcination temperature. The nondestructive characterization of PAS in the ultraviolet visible region suggested that increasing calcination temperature promoted changes in chemical structures and an apparent decrease in gap energy. The separation of superimposed absorption bands referring to charge transfers from the ligand to the metal and the nanodomains of the transition metals suggested the possible absorption centers present at the absorption threshold of the analyzed oxides. Through the XRD analysis, the formation of stable phases such as T-Nb16.8O42, o-Nb12O29, and rutile was observed at a lower temperature level, suggesting pore induction and an increase in surface area for the oxides studied, at a calcination temperature below that expected by the related literature. In addition, the synthesis with a higher temperature level altered the previously existing morphologies of the Ti:Nb, base and modified with Ru, forming the new mixed crystallographic phases Ti2Nb10O29 and TiNb2O7, respectively. As several semiconductor oxide applications aim to reduce costs with photoexcitation under visible light, the modified Ti:Ru oxide calcined at a temperature of 800 °C and synthesized according to the sol-gel methodology used in this work is suggested as the optimum preparation point. This study presented the formation of a stable crystallographic phase (rutile), a significant decrease in gap energy (2.01 eV), and a visible absorption threshold (620 nm).

Adsorptive-Photocatalytic Composites of α-Ferrous Oxalate Supported on Activated Carbon for the Removal of Phenol under Visible Irradiation.

Adsorptive-photocatalytic composites based on activated carbon (AC) and α-ferrous oxalate dihydrate (α-FOD) were synthesized by an original two-step method and subsequently used for the removal of phenol from aqueous solutions. To obtain the composites, ferrotitaniferous black mineral sands (0.6FeTiO3·0.4Fe2O3) were first dissolved in an oxalic acid solution at ambient pressure, and further treated under hydrothermal conditions to precipitate α-FOD on the AC surface. The ratio of oxalic acid to the mineral sand precursor was tuned to obtain composites with 8.3 and 42.7 wt.% of α-FOD on the AC surface. These materials were characterized by X-ray powder diffraction, scanning electron microscopy, and the nitrogen adsorption-desorption method. The phenol removal efficiency of the composites was determined during 24 h of adsorption under dark conditions, followed by 24 h of adsorption-photocatalysis under visible light irradiation. AC/α-FOD composites with 8.3 and 42.7 wt.% of α-FOD adsorbed 60% and 51% of phenol in 24 h and reached a 90% and 96% removal efficiency after 12 h of irradiation, respectively. Given its higher photocatalytic response, the 42.7 wt.% α-FOD composite was also tested during successive cycles of adsorption and adsorption-photocatalysis. This composite exhibited a reasonable level of cyclability (~99% removal after four alternated dark/irradiated cycles of 24 h and ~68% removal after three simultaneous adsorption-photocatalysis cycles of 24 h). The promising performance of the as-prepared composites opens several opportunities for their application in the effective removal of organic micropollutants from water.

Tailoring structural and optical properties of Cu(II)-induced MgAl2O4 nanoparticles and their response to toxic dyes under solar illumination.

Worldwide environmental challenges pose critical problems with the growth of the global economy. Addressing these issues requires the development of an eco-friendly and sustainable catalyst for degrading organic dye pollutants. In this study, copper-doped magnesium aluminates (CuxMg1-xAl2O4) with x = 0.0-0.8 were synthesized using a citrate-based combustion route. The inclusion of Cu(II) significantly impacted the structural, microstructural, optical, and photocatalytic activity of the catalyst. Rietveld analysis of X-ray diffraction powder profiles revealed single-phase spinels crystallized in the face-centered cubic unit cell with space group. Chemical states of the ions, surface morphology, and elemental investigation were analyzed by X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, and energy-dispersive X-ray spectroscopy, respectively. UV-visible and diffuse reflectance spectroscopies confirmed the reduction of the band gap due to Cu(II) doping, validated by first-principle investigations using the WIEN2k code. The catalyst with x = 0.8 showed higher photocatalytic efficacy (90% and 93%) for removing two azo organic dye pollutants, rhodamine B and methyl orange, respectively, within 120min. Degradation kinetics followed a pseudo-first-order mechanism. The doped (0.8) sample was structurally and morphologically stable and reusable under visible irradiation, retaining performance after three runs. Scavenger studies confirmed hydroxyl and superoxide radicals' involvement in the degradation. This work presents an effective approach to enhancing CuxMg1-xAl2O4 catalysts' photodegradation performance, with potential applications in pharmaceuticals and wastewater remediation.

Self-assembly TiO2@Silane@SiO2 core-shell as s-scheme heterojunction photocatalyst against methylene blue degradation: synthesis and mechanism insights

Pollutants are the most critical threats to the health of water resources. On this basis, fabricating a core-shell as an S-scheme heterojunction photocatalyst for the treatment of wastewater from methylene blue (MB) dye was aimed in this research. In this study, TiO2-doped silanized silica dielectric nanocomposites were synthesized as self-assembly TiO2@Silane@SiO2 heterojunction through sol-gel and solvothermal methods using tetrabutyl orthotitanate (TBOT) as precursor followed by calcination at 650 °C for 3 h. Silanization of silica nanoparticles was done at two different concentrations. The results showed that layer-by-layer synthesis (i.e. self-assembly of APTES on SiO2, precipitation of TiO2 layer on it by sol-gel technique and then calcination) was the optimum preparation method. The structural and morphological features were investigated by XRD, FTIR, BET, TGA-DTG, FE-SEM, EIS and ESR techniques. It was found that the band gap energy of nanocomposite particles reduced from 3.14 eV for the sample prepared by the solvothermal method (i.e. without APTES) to 2.91 eV (i.e. shifting the light absorption from UV to the visible region) for the sample prepared by the sol-gel layer-by-layer method. The prepared samples were used against the photo-degradation of MB. TiO2@Silane@SiO2 core-shell nanoparticles exhibited efficient photocatalytic degradation against MB with a photodegradation efficiency of 85 % under UV and 60 % under visible irradiation. Finally, the prepared nanocomposite particles were incorporated to an emulsion acrylic resin to prepare photocatalytic polymer film. The prepared films were evaluated for photocatalytic degradation of MB stain and mechanical performances. It was found that the TiO2@Silane@SiO2 nanocomposite particles that prepared by layer-by-layer method caused about 56 % improvement in hydrophobicity, 276.7 % increment in the tensile strength, 109.6 times enhancement in the modulus, 381.4 times enhancement in the toughness and 57.6 times improvement in the elongation at break of the acrylic film compared to the pure TiO2-containing acrylic film, respectively.

Lanthanum anchored NiCo2S4 nanocomposite and their structural, optical, and enhanced photodegradation of Indigo Carmine (InC) dye

The focus of this study is to explore the potential of lanthanum-anchored NiCO2S4 (L-NCS) as a photocatalyst for Indigo carmine (InC) dye under visible radiation. Different analytical techniques including XRD, SEM, TEM, and PL were used to confirm the uniform distribution of lanthanum on NiCO2S4. A study of the optical and photochemical properties of L-NCS revealed a reduction in charge carrier recombination and an increase in visible light sensitivity due to the introduction of soft metal dopants into NCS. The optimized L-NCS catalyst showed a significant increase in photodegradation rate, about 7.2 times higher than that of pure NCS when exposed to visible light. Furthermore, the reproducibility of L-NCS shows excellent stability as a photocatalyst for environmental remediation.

Charge Redistribution in Nise2/Mos2 n–n Heterojunction Towards the Photoelectrocatalytic Degradation of Ciprofloxacin

AbstractThis study reports the photoelectrocatalytic (PEC) activity of a n–n heterojunction comprising MoS2 and NiSe2. The synthesis of the composite was achieved through a facile solvothermal method, yielding an exfoliated MoS2 layered sheet loaded with NiSe2 nanoparticles. Under visible light radiation and an external electric field, the obtained composite NiSe2/MoS2 exhibited enhanced catalytic activity for ciprofloxacin (CIP) degradation. The NiSe2/MoS2 heterojunction achieved about 78 % degradation efficiency with a first‐order kinetic rate of 0.0111 min−1, compared to 38 % efficiency and a first‐order kinetic rate of 0.0044 min−1 observed for MoS2. The NiSe2/MoS2 heterojunction was more advantageous due to the synergy of charge carrier induction by visible light radiation and improved charge carrier separation induced by the external electric field. The formation of n–n heterojunction at the interface of the two materials resulted in charge redistribution in the materials, with a simultaneous realignment of the band structure to achieve Fermi energy equilibration. The primary reactive species responsible for CIP degradation was identified as the photo‐induced h+. Furthermore, the catalyst exhibited high stability and reusability, with no significant reduction in activity observed after five experimental cycles. This study reveals the potential of exploring the synergy between the photocatalytic and electrocatalytic processes in removing harmful pharmaceutical compounds from water.

Investigation of Criteria for Comparing of Natural and LED Radiation Spectral Distribution

The difference in the spectral composition of artificial and natural lighting can negatively affect health, as well as lead to a distorted perception of the color of surrounding objects. At the same time, a certain correction of the spectral composition of visible radiation in medical institutions and workplaces has a positive effect on human health, while can be carried lighting control out taking into account the data of personal sensor devices that determine the human condition. The purpose of the research was to select criteria for comparing natural and LED optical and visible radiation by spectral composition and by the visibility of color differences in natural and LED lighting. The effectiveness of the application of known and developed criteria for assessing the difference in the spectral composition of optical and visible radiation from natural and LED sources was investigated, as well as for the visibility of color differences in natural and LED lighting. To minimize the values of criteria are proposed additive and subtractive methods for calculating LED parameters. Their comparison allowed us to conclude that a more complex calculation algorithm, but higher performance for an additive technique than for a subtractive one with the same minimization results.It was found that to simulate the spectral composition of natural radiation using LEDs, it is most effective to use the criteria "standard deviations of the relative differences between the optical and visible spectral components of natural and LED radiation". A comparison of the criteria for the visibility of color differences in natural and LED lighting showed approximately the same effectiveness of using the criteria "small color differences" and "standard deviation by photoreceptors" at the present stage and the prospects for applying the second criterion, provided that its acceptable values are established.

Photocatalytic Polyaromatic hydrocarbons (PAH) utilizing magnetic CrFe2O4 nanoparticle: Green synthesis, characterization, ab initio studies, electronic, magnetic features and water treatment application

Polyaromatic hydrocarbons (PAHs) are priority pollutants due to their mutagenicity, persistence, and proven carcinogenicity. Consequently, we investigated the photooxidative degradation of prototypical toxic PAHs, namely anthracene (ANTH) and phenanthrene (PHEN), and naphthalene (NAPH) utilizing magnetic CrFe2O4 nanoparticles under visible light LED irradiation. The prepared nanoparticles, characterized by P-XRD, IR, and SEM, reveal a cubic (FCC) structure and an average particle size of 25.6 nm. On Ab initio study we employed spin polarized first-principle calculations using the Full-Potential Linearized Augmented Plane-Wave (FLAPW) method with GGA-mBJ potentials implemented in the Wien2k package to investigate the properties of CrFe2O4 spinel compound; the calculations reveal that CrFe2O4 adopts a cubic crystal structure with space group 227 (Fd-3 m), and exhibits semiconductor characteristics in both spin channels, featuring indirect band gaps of 1.12 eV (spin-up) and 0.43 eV (spin-down) at the Γ-L and K-Γ points, respectively. Furthermore, the material demonstrates ferromagnetic behavior, with a spin magnetic moment of 20 µB per unit cell. Optical spectra analysis concurs with band structure calculations, suggesting the suitability of this material for photovoltaic applications. The CrFe2O4 magnetic nanoparticles were synthesized through an eco-friendly approach using Boswellia carteri resin as a natural surfactant in an aqueous medium. Our synthesized materials exhibited excellent photocatalytic performance, leading to a rapid exponential decay of ANTH and PHEN over 3 h under visible LED light. The effect of different radical scavengers revealed the role of the percentage of active species OH, h+, and ˙O2− in the oxidation of selected PAHs. At neutral pH, the photo-degradation of PAHs (200 g L−1) by CrFe2O4 (10 mg) followed first-order kinetics and the Langmuir model (R2: 0.99). Exceptional degradation efficiencies were achieved, with ANTH exhibiting a removal efficiency of 99 %, PHEN of 90 %, and NAPH of 86 %. These results show the effectiveness of the synthesized materials as benign and environmentally friendly magnetic nanoparticles for removing carcinogenic PAHs, offering a sustainable, green, and reusable (n = 7) catalytic system to address this environmental challenge.

Black phosphorus quantum dots functionalized with photochromic poly(vinylspiropyran)-grafted polydopamine for transient digital-type memristors

Abstract The covalent functionalization of black phosphorus quantum dots (BPQDs) with organic species or polymers will inevitably change or damage their electronic structure and intrinsic structure. To address this problem and explore the application of BPQDs in transient digital-type memristors, a polydopamine (PDA) thin film is first synthesized in situ onto the surface of BPQDs to produce a donor–acceptor-type BPQDs@PDA composite that is directly used to react with 2-bromoisobutyryl bromide to give BPQDs@PDA-Br. By using BPQDs@PDA-Br as an atom transfer radical polymerization agent, a large number of polyvinylspiropyran (PSP) chains are in situ grown from the PDA surface to yield BPQDs@PDA-PSP. Upon ultraviolet (UV)–visible light illumination, the 2 isomers of the spiropyran (ring-closed spiropyran form and ring-opened merocyanine) in the PSP moieties will interconvert into each other rapidly. As expected, the as-fabricated indium tin oxide (ITO)/BPQDs@PDA-PSP/ITO device exhibits typical nonvolatile digital-type memristive performance under visible irradiation, with a small turn-on voltage of −1.52 V, a turn-off voltage of +1.16 V, and an ON/OFF ratio current ratio of 1.02 × 104. Upon UV illumination, the information stored in the device is quickly and completely erased within 6 s. By utilizing a simple memristor-based convolutional neural network, one can easily realize handwritten digit recognition. After 10 epochs of training, numeral recognition accuracy can reach up to 96.21%.

Laboratory demonstration of image plane self-calibration in interferometry

We demonstrate the shape-orientation-size conservation principle for a three-element interferometer using aperture plane masking at the ALBA visible synchrotron radiation light source. We then use these data to demonstrate image plane self-calibration.

Visible light-boosted photodegradation activity of Ag–AgVO3/Zn0.5Mn0.5Fe2O4 supported heterojunctions for effective degradation of organic contaminates

Abstract One of the most important concerns in developing efficient heterojunction photocatalysts for the photodegradation of environmental contaminants is the enhancement and acceleration of photocarrier separation. In this study, novel nanocomposite photocatalysts of Ag–AgVO3 nanorods grafted with Zn0.5Mn0.5Fe2O4 metal ferrites nanoparticles were developed by using facial hydrothermal and coprecipitation techniques for the effective photodegradation of Rhodamine B (Rh B) under visible light exposure. The fabricated materials were analyzed in detail using scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDS), nitrogen adsorption/desorption, transmission electron microscopy (TEM), photoluminescence spectroscopy (PL), vibrating sample magnetometer, and ultraviolet–visible diffuse reflectance spectroscopy (DRS). The results showed an efficient contribution when compared to the earlier research. The TEM showed a hybrid of nanorods of supported composite with metal ferrite and Ag attached on the surface, consistent with field emission scanning electron microscopy and EDS results. The DRS expressed a lower band gap for supported nanocomposites (1.5 eV), which, arranged with PL, showed a lower recombination rate of supported nanocomposites. The surface properties showed that the supported hybrid might be as small as 45.42 nm or as large as 20.33 nm compared with others. When comparing the photocatalytic activity of pure AgVO3, Ag/AgVO3, and Zn0.5Mn0.5Fe2O4 photocatalysts, the performance of Ag–AgVO3/Zn0.5Mn0.5Fe2O4 nanocomposite photocatalyst was clearly superior (more than 99.9% degradation efficiency was achieved). The boosted activity the Ag–AgVO3/Zn0.5Mn0.5Fe2O4 photocatalyst system was justified by Z-system heterojunction induced by the plasmonic effect, and the suggested mechanism was investigated by quenching of reactive species by scavengers. The degradation performance was achieved under optimum conditions (pH = 2, 20 ppm of pollutant concentration, 120 mM of hydrogen peroxide, 1 g/L of catalysts dose). The results showed that after 240 min of visible irradiation resulted in the high (chemical oxygen demand) and (total organic carbon) reductions with a removal efficiency of (85) to (90%) for Rh B dye. The fabricated Ag–AgVO3/Zn0.5Mn0.5Fe2O4 nanocomposites were effective in the degradation of organic pollutants in wastewater treatment.

Economical, one-pot, and green synthesis of plant-based carbon quantum dots for efficient visible-light photocatalytic dye degradation and water purification

BackgroundGreen, in-situ, one-pot, facile, and economical synthesis of efficient photocatalysts to destroy emerging aqueous contaminants is essential. MethodBiocompatible carbon quantum dots (CQDs) photocatalysts were successfully synthesized from a plant source called garden thyme as a low-cost precursor by one-step calcination method. CQDs were synthesized in both pure form and co-doped with fluorine and boron indicating size of <10 nm and favorable quantum yield of 40%. Four key factors including synthesis temperature, synthesis time, fluorine and boron weight ratios, and CQDs size were investigated on removal rates of organic pollutant Rhodamine B (RhB). Significant findings10%F-10%B co-doped CQDs with synthesized at 400 ºC for 5 h with a size of <10 nm, showed the highest photocatalytic RhB degradation performances of 86.1% and 89% within 40 and 60 min, respectively. This improved performance was originated from synergetic influences of quantum size, co-doping, promising quantum yield, and great visible light harvesting, that satisfactorily separated and transported light-created electron-hole pair. Trapping experimental data approved that hydroxyl radicals were dominant reactive species that oxidized RhB on F,B co-doped CQDs catalysts upon visible light radiation. Overall, CQDs could be easily synthesized as a green and super-cheap photocatalyst and would be effective for wastewater treatments.