Ti 13Nb 13Zr Alloy Research Articles

A study on the physicochemical properties of surface modified Ti13Nb13Zr alloy for skeletal implants

As it is widely stated in the literature, biofilms are responsible for most chronic infections, which have grown exponentially over the past three decades. The use of so-called alloys, as a new generation of materials, enables us to find the golden mean in the arena widely known as implantology. The use of the surface layer, using the chosen Atomic Layer Deposition method, is to be the basis for minimizing the risk of an organism reactions. Therefore, the primary objective of this study was to observe the impact of physicochemical properties of the surface layers (bactericidal) on the processes that occur on the implants surface made of titanium biomaterials used in bone structures. The study also attempted to evaluate the physicochemical properties of the ZnO coatings, deposited on the substrate of one of the new generation Ti13Nb13Zr alloys, using the ALD method. Included in the assessment of the physicochemical properties of the surface layers formed in this manner, we perform pitting corrosion resistance tests, scratch tests, tribological tests and surface wettability tests. Based on the obtained data, the differing physicochemical properties of the alloy with ZnO coatings are found to be dependent on the applied surface modification. For the conducted tests, differences are determined for the tests on the corrosion resistance, surface wettability and the abrasion resistance for samples with and without the ZnO coating. In addition, tests show that the coating applied to the alloy, which is previously subjected to the sand-blasted process, is characterized by improved adhesion.

Characteristics of Ca-, P- and Si- Containing Oxide Coatings Obtained by Micro-Arc Oxidation on the Selective Laser Melted Ti13zr13nb Alloy

Characteristics of Ca-, P- and Si- Containing Oxide Coatings Obtained by Micro-Arc Oxidation on the Selective Laser Melted Ti13zr13nb Alloy

Microstructural Characterization and Wear Behavior of Porous Equimolar TiNbZr Medium-Entropy Alloys Scaffolds Produced by Mechanical Alloying

Recently, there has been increasing importance on scaffold materials that could be used in biomaterials. In the present study, equimolar TiNbZr medium entropy alloys (MEAs) and porous TiNbZr alloy scaffolds were produced by mechanical alloying (MA) that is a powder metallurgy processing technique. The MA process was carried out using high energy planetary ball mill. Ammonium bicarbonate (NH4HCO3) at different percentage ratio was used as space holder to fabricate the porous TiNbZr scaffolds with using space-holder sintering method. Cold Isostatic Pressing (CIP) was performed for consolidation of mechanically alloyed powders. Finally, the green compact samples were sintered in tube furnace under vacuum atmosphere. The microstructural analyses, phase composition, porosity and density measurement, compression and microhardness tests and wear resistance of bulk alloys were examined. The X-Ray Diffraction (XRD) patterns of all samples indicated the dominant β-Ti phases and small amount of α-Ti phase. SEM (scanning electron microscope) images for porous TiNbZr alloy scaffolds demonstrated that porosity increased with increase of space holders amount. With the increasing porosity content, density, hardness, compressive strength and the elastic modulus of samples decreased while wear rate increased.

Microstructure and Mechanical Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings

Abstract Laser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two different laser powers of 800 W and 900 W and for different scan rates: 3 mm/s or 6 mm/s at 25 Hz, and the pulse duration was 2.25 ms or 3.25 ms. A scanning electron microscope SEM was used to evaluate the surface structure of the modified samples. To observe the heat-affected zones of the individual samples, metallographic samples were taken and observed under an optical microscope. Surface wettability tests were performed using a goniometer. A surface roughness test using a profilograph and a nanoindentation test by NanoTest™ Vantage was also performed. Observations of the microstructure allowed to state that for higher laser powers the surfaces of the samples are more homogeneous without defects, while for lower laser powers the path of the laser beam is clearer and more regular. Examination of the microstructure of the cross-sections indicated that the samples on which the carbon nanotube coating was deposited are characterized by a wider heat affected zone, and for the samples modified at 800 W and a feed rate of 3 mm/s the widest heat affected zone is observed. The wettability tests revealed that all the samples exhibit hydrophilic surfaces and the samples with deposited carbon nanotube coating increase it further. Surface roughness testing showed a significant increase in Ra for the laser-modified samples, and the presence of carbon nanotubes further increased this value. Nanoindentation studies showed that the laser modification and the presence of carbon coating improved the mechanical properties of the samples due to their strength.

The Effect of the Corrosion Medium on Silane Coatings Deposited on Titanium Grade 2 and Titanium Alloy Ti13Nb13Zr.

The present paper focuses on the fabrication of coatings based on vinyltrimethoxysilane and the influence of various corrosion media on the coatings produced. Coatings were deposited on two substrate materials, namely, titanium Grade 2 and titanium alloy Ti13Nb13Zr, by immersion in a solution containing vinyltrimethoxysilane, anhydrous ethyl alcohol, acetic acid and distilled water. The obtained coatings were characterized in terms of surface morphology, adhesion to the substrate and corrosion resistance. As corrosion solutions, four different simulated physiological fluids, which differed in the contents of individual ions, and a 1 mol dm−3 NaBr solution were used. The chloride ions contained in the simulated physiological fluids did not lead to pitting corrosion of titanium Grade 2 and titanium alloy Ti13Nb13Zr. This investigation shows that titanium undergoes pitting corrosion in a bromide ion medium. It is demonstrated that the investigated coatings slow down corrosion processes in all corrosion media examined.

Properties of chitosan/CuNPs coatings electrophoretically deposited on TiO2 nanotubular oxide layer of Ti13Zr13Nb alloy

Coatings based on chitosan/CuNPs (chit/CuNPs) were obtained by a one-step electrophoretic deposition (EPD) on nanotubular oxide layer of Ti13Zr13Nb alloy. The deposition was carried out for 1 min applying voltages of 10 and 20 V with and without the addition of dispersing agent (Polysorbate 20) to the suspension. The coatings obtained for the lower voltage were more uniform than for the higher voltage. By adding a dispersing agent, the agglomeration of copper nanoparticles was reduced, resulting in better adhesion of the coating to the metallic substrate, good corrosion resistance and improved wettability.

Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate

Three coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and phase composition, roughness, hardness, Young’s modulus, plastic, and elastic behavior. The results showed that the best mechanical properties in terms of biomedical application were achieved for the MWCNTs coating with titania outer layer. Nevertheless, both the addition of nanocopper and titania improved the mechanical resistance of the base MWCNTs coating. Compared to our previous experiments on Ti13Nb13Zr alloy, a general tendency is observed to form more homogenous coatings on pure metal than on the alloy, in which chemical and phase compositions are more complex.

Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy.

Titanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare mechanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and dispersion coatings comprised of simultaneously deposited MWCNTs and nanoCu, each electrophoretically deposited on the Ti13Nb13Zr alloy. Optical microscopy, scanning electron microscopy, X-ray electron diffraction spectroscopy, and nanoindentation technique were applied to study topography, chemical composition, hardness, plastic and elastic properties. The results demonstrate that the addition of nanocopper or titanium dioxide to MWCNTs coating increases hardness, lowers Young’s modulus, improves plastic and elastic properties, wear resistance under deflection, and plastic deformation resistance. The results can be attributed to different properties, structure and geometry of applied particles, various deposition techniques, and the possible appearance of porous structures. These innovative coatings of simultaneously high strength and elasticity are promising to apply for deposition on long-term titanium implants.

A new insight into the α phase precipitation in β titanium alloy

The α phase precipitation of β →β’→α in the Ti–13Nb–13Zr alloy has been observed by transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). The images clearly show that the α phase nucleates at the β′ interface which has a rotation angle with the β matrix. The precipitation of α phase from the β′ phase experiences four steps, each step is similar to the twinning and the symmetric angle successively increases from 57° to 62°, 76° and finally to 90°. The crystallographic relationships between β and β’ were also discussed. This study provides guidance in the future for tailoring microstructure of titanium alloys.

Microstructure, Micro-Mechanical and Tribocorrosion Behavior of Oxygen Hardened Ti-13Nb-13Zr Alloy.

In the present work, an oxygen hardening of near-β phase Ti–13Nb–13Zr alloy in plasma glow discharge at 700–1000 °C was studied. The influence of the surface treatment on the alloy microstructure, tribological and micromechanical properties, and corrosion resistance is presented. A strong influence of the treatment on the hardened zone thickness, refinement of the α’ laths and grain size of the bulk alloy were found. The outer hardened zone contained mainly an oxygen-rich Ti α’ (O) solid solution. The microhardness and elastic modulus of the hardened zone decreased with increasing hardening temperature. The hardened zone thickness, size of the α’ laths, and grain size of the bulk alloy increased with increasing treatment temperature. The wear resistance of the alloy oxygen-hardened at 1000 °C was about two hundred times, and at 700 °C, even five hundred times greater than that of the base alloy. Oxygen hardening also slightly improved the corrosion resistance. Tribocorrosion tests revealed that the alloy hardened at 700 °C was wear-resistant in a corrosive environment, and when the friction process was completed, the passive film was quickly restored. The results show that glow discharge plasma oxidation is a simple and effective method to enhance the micromechanical and tribological performance of the Ti–13Nb–13Zr alloy.

The Influence of Nanometals, Dispersed in the Electrophoretic Nanohydroxyapatite Coatings on the Ti13Zr13Nb Alloy, on Their Morphology and Mechanical Properties.

In this work, nanohydroxyapatite coatings with nanosilver and nanocopper have been fabricated and studied. The presented results concern coatings with a chemical composition that has never been proposed before. The present research aims to characterize the effects of nanosilver and nanocopper, dispersed in nanohydroxyapatite coatings and deposited on a new, non-toxic Ti13Zr13Nb alloy, on the physical and mechanical properties of coatings. The coatings were obtained by a one-stage electrophoretic process. The surface topography, and the chemical and phase compositions of coatings were examined with scanning electron microscopy, atomic force microscopy, X-ray diffractometry, glow discharge optical emission spectroscopy, and energy-dispersive X-ray spectroscopy. The mechanical properties of coatings were determined by nanoindentation tests, while coatings adhesion was determined by nanoscratch tests. The results demonstrate that copper addition increases the hardness and adhesion. The presence of nanosilver has no significant influence on the adhesion of coatings.

Structure, tribological properties, and the growth mechanism of in-situ generated TiC in titanium cermet

Titanium cermet combining metallic toughness with ceramic wear resistance has been proven to be a potential candidate for implanted joint material. In this work, titanium cermet was synthesized by means of the elevated temperature solid carburizing technology. The Ti13Nb13Zr alloy surface was found to be converted into TiC ceramic layer combined with a carbon strengthened diffusion zone underneath. The overall thickness of the carburized region grew to about 100 µm after 120 min carburization at 1,500 K. In order to clarify the growth behaviors of TiC ceramic layer, a growth mechanism is proposed. At the beginning of carburizing process, carbonaceous gas decomposed from carburizer due to high temperature and then converted to free atomic carbons through reduction reaction. Then, in-situ generated TiC ceramic layer possessing certain thickness formed on the surface, meanwhile, the inner carbon diffusion zone also grew inwards due to physical diffusion of carbon, and finally forming a gradient carbon distribution. In addition, the tribological behaviors of the new materials were evaluated through reciprocating ball-on-plate sliding wear tests in bovine calf serum. Although there was an increase in friction coefficient, the wear rate decreased by 59.6% due to the formation of the wear-resistant TiC ceramic layer. The wear mechanisms evolved from severe abrasive wear for bare Ti13Nb13Zr alloy to mild adhesive wear for titanium cermet.

The Chemical and Biological Properties of Nanohydroxyapatite Coatings with Antibacterial Nanometals, Obtained in the Electrophoretic Process on the Ti13Zr13Nb Alloy.

The risk of an early inflammation after implantation surgery of titanium implants has caused the development of different antimicrobial measures. The present research is aimed at characterizing the effects of nanosilver and nanocopper dispersed in the nanohydroxyapatite coatings, deposited on the Ti13Zr13Nb alloy, and on the chemical and biological properties of the coatings. The one-stage deposition process was performed by the electrophoretic method at different contents of nanomaterials in suspension. The surface topography of the coatings was examined with scanning electron microscopy. The wettability was expressed as the water contact angle. The corrosion behavior was characterized by the potentiodynamic technique. The release rate of copper and silver into the simulated body fluid was investigated by atomic absorption spectrometry. The antibacterial efficiency was evaluated as the survivability and adhesion of the bacteria and the growth of the biofilm. The cytotoxicity was assessed for osteoblasts. The results demonstrate that silver and copper increase the corrosion resistance and hydrophilicity. Both elements together effectively kill bacteria and inhibit biofilm growth but appear to be toxic for osteoblasts. The obtained results show that the nanohydroxyapatite coatings doped with nanosilver and nanocopper in a one-stage electrophoretic process can be valuable for antibacterial coatings.

Dislocation structure and phase composition of Ti13Nb13Zr after high-pressure torsion

The approach based on synchrotron X-ray diffraction was applied in this research to investigate the dislocation and phase structures of severely deformed disk of Ti13Nb13Zr alloy. It was found, that the final structure of the material is inhomogeneous along the disk diameter. The local area of highest dislocation density of α′-phase matches with the zone of passed deformation-induced phase transformations.

Plasma-Sprayed HA/Sr Reinforced Coating for Improved Corrosion Resistance and Surface Properties of Ti13Nb13Zr Titanium Alloy for Biomedical Implants

Surgical implants are generally made-up of light metal or alloys like titanium and titanium alloys. In this study, attempts are made to enhance the mechanical properties and corrosion resistance by developing a protective layer with plasma-sprayed strontium-reinforced hydroxyapatite (HA-Sr) coatings at three levels (4, 8, and 12%) of weight percent (wt%) of Sr powder. The findings show that the surface hardness increases on increasing the Sr content in HA, whereas the surface roughness tends to decrease on Sr increment. The bare Ti13Nb13Zr substrate shows hydrophobic behavior while all the coated substrates are hydrophilic and give rise to the improved clinical performance of the implant. The electrochemical study showed that HA/Sr coated substrates possesses higher corrosion resistance than bare and pure HA-coated titanium substrate. The outcomes of this study indicated that the Ti13Nb13Zr alloy plasma-sprayed with HA and HA/Sr is beneficial for future bone implant applications.

Comparative Study of Superelastic Ti–Zr–Nb and Commercial VT6 Alloy Billets by QForm Simulation

A comparative simulation of hot radial shear rolling (RSR) of billets made of a superelastic Ti–Zr–Nb and a commercial VT6 alloy was performed using the QForm finite element modeling program. Rolling in 48 modes with a variable feed angle and elongation ratio at 4 levels and initial rolling temperature at 3 levels was investigated for each alloy. The Ti–Zr–Nb alloy rheology during hot deformation was determined experimentally by hot upset forging and imported into the QForm program. The presence of maxima on the flow curves at the initial stage of deformation, which are absent in the VT6 alloy, is revealed. Simulation results are presented in the form of fields of the stiffness coefficient, strain rate intensity, cumulative strain degree in the maximum reduction section depending on the rolling mode. General regularities of the Ti–Zr–Nb and VT6 behavior in RSR are similar. The gradient of the fields studied decreases, and the roll pressure and torque increase with an increase in the feed angle and elongation ratio. The initial rolling temperature does not significantly affect the deformation pattern, but it significantly affects the roll pressure and torque. At the same time, the experimental alloy demonstrated the greater tendency to localize deforming forces in the near-contact zone and to increase the gradient of stress-strain state parameters over the billet section. The study of the tightening shape and depth of rolled billet ends showed that the Ti–Zr–Nb alloy has a 3.5–9.6% greater tightening depth. It is shown that experimental alloy rolling requires 1.6–2.4 times higher roll pressure and torque as compared to the commercial alloy.

Comparative study of superelastic Ti–Zr–Nb and commercial VT6 alloy billets by QForm simulation

A comparative simulation of hot radial shear rolling (RSR) of billets made of a superelastic Ti–Zr–Nb and a commercial VT6 alloy was performed using the QForm finite element modeling program. Rolling in 48 modes with a variable feed angle and elongation ratio at 4 levels and initial rolling temperature at 3 levels was investigated for each alloy. The Ti–Zr–Nb alloy rheology during hot deformation was determined experimentally by hot upset forging and imported into the QForm program. The presence of maxima on the flow curves at the initial stage of deformation, which are absent in the VT6 alloy, is revealed. Simulation results are presented in the form of fields of the stiffness coefficient, strain rate intensity, cumulative strain degree in the maximum reduction section depending on the rolling mode. General regularities of the Ti–Zr–Nb and VT6 behavior in RSR are similar. The gradient of the fields studied decreases, and the roll pressure and torque increase with an increase in the feed angle and elongation ratio. The initial rolling temperature does not significantly affect the deformation pattern, but it significantly affects the roll pressure and torque. At the same time, the experimental alloy demonstrated the greater tendency to localize deforming forces in the near-contact zone and to increase the gradient of stress-strain state parameters over the billet section. The study of the tightening shape and depth of rolled billet ends showed that the Ti–Zr–Nb alloy has a 3.5–9.6 % greater tightening depth. It is shown that experimental alloy rolling requires 1.6–2.4 times higher roll pressure and torque as compared to the commercial alloy.

Residual stress distribution and surface geometry of medical Ti13Nb13Zr alloy treated by laser shock peening with flat-top laser beam

The metallic implants made of Ti13Nb13Zr alloy are usually used under the action of the cyclic loads conditions and fatigue failure occurs occasionally. Laser shock peening (LSP) is an innovative surface treatment process, which has been used to improve the fatigue life of metallic materials. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the effects on the residual stress distribution and surface geometry. A neodymium doped yttrium lithium fluoride (Nd: YLF) pulse laser with a flat-top beam was applied at three different overlapping rates (10%, 30%, 50%), laser pulse energies (5J, 6J, 7J), and impact times (1 impact, 2 impacts, 3 impacts), respectively. The residual stresses were determined by X-ray diffractometer with sin 2ψ method. Firstly, the 30% overlap was chosen by comparing the residual stresses induced by LSP with different overlapping rates. Then, the effects of laser energies and impact times on surface residual stresses, in-depth residual stresses, surface deformation, and surface roughness were investigated and compared. The results showed that the residual stresses, surface deformation, and surface roughness increase with the increasing laser energies and impact times. The effected layer depth of residual stress is about 1058 μm with the 6J laser energy.

Biocompatibility and Antibacterial Properties of ZnO-Incorporated Anodic Oxide Coatings on TiZrNb Alloy.

In a present paper, we demonstrate novel approach to form ceramic coatings with incorporated ZnO nanoparticles (NPs) on low modulus TiZrNb alloy with enhanced biocompatibility and antibacterial parameters. Plasma Electrolytic Oxidation (PEO) was used to integrate ZnO nanoparticles (average size 12–27 nm), mixed with Ca(H2PO2)2 aqueous solution into low modulus TiZrNb alloy surface. The TiZrNb alloys with integrated ZnO NPs successfully showed higher surface porosity and contact angle. XPS investigations showed presence of Ca ions and absence of phosphate ions in the PEO modified layer, what explains higher values of contact angle. Cell culture experiment (U2OS type) confirmed that the surface of as formed oxide-ZnO NPs demonstrated hydrophobic properties, what can affect primary cell attachment. Further investigations showed that Ca ions in the PEO coating stimulated proliferative activity of attached cells, resulting in competitive adhesion between cells and bacteria in clinical situation. Thus, high contact angle and integrated ZnO NPs prevent bacterial adhesion and considerably enhance the antibacterial property of TiZrNb alloys. A new anodic oxide coating with ZnO NPs could be successfully used for modification of low modulus alloys to decrease post-implantation complications.

Function-structure-integrated Ti-HA coatings on TiNbZr with enhanced mechanical properties and bioactivity prepared by spark plasma sintering

Clinical applications of orthopedic implants require porous structure and hydroxyapatite for osseointegration and osteoinductivity. Nevertheless, contents of hydroxyapatite (HA) and high porosity will degenerate mechanical and corrosion properties of implants. Therefore, a novel function-structure-integrated (Ti–Nb–Zr)/(Ti-HA) composites with high strength, activity and porosity and low elastic modulus consisting of a high dense Ti–13Nb–13Zr core and an external micro- and macro-porous Ti-HA part were designed and fabricated. The central compact Ti–Nb–Zr alloy provides excellent mechanical properties, while the external part with appropriate characteristics of porous structure and bioactive HA, which enhances bioactivity and provides low elastic modulus. The relative density of Ti–Nb–Zr part was 92%, and the porosity of radial Ti-HA part were between 35.3% (5 wt% HA) and 40.1% (20 wt% HA). The compressive strength of composites exhibits a remarkable improvement from 248 to 421 MPa and the elastic modulus from 10.8 to 18.9 GPa. Bioactive HA and specific pores characteristics induced bone-like apatites to deposit on porous part. The homogeneity and thickness of bioactive apatite layer on composites were enhanced with the increase of HA contents. Experimental results of bone mesenchymal stem cells (BMSCs) proliferation, the HA and the pore structure make the (Ti–Nb–Zr)/(Ti-HA) exhibited good cell activity and extensibility to BMSCs. This research would offer a potential strategy for designing and preparing function-structure-integrated orthopedic implants.