Thermionic Source Research Articles

ZnO Nanowire Cold Cathode Hemispherical X‐Ray Sources

AbstractCurved or spherical X‐ray sources are significant for use in intraoperative radiotherapy, adaptive static medical imaging, and high‐throughput industrial inspection, but they are hard to achieve using traditional thermionic cathode point electron sources. In this study, copper (Cu)‐doped zinc oxide (ZnO) nanowires grown on a brass substrate with a designed shape are proposed to achieve cold cathode hemispherical X‐ray sources. The strain‐driven solid–liquid growth model of Cu‐doped ZnO nanowires is proposed, and the oxidation temperature‐dependent and time‐dependent growth characteristics are investigated to optimize the morphologies of ZnO nanowire cold cathodes with a typical turn‐on field of 7.36 MV m−1, a maximum current of 12.54 mA (4.93 mA cm−2) and a uniform field emission image with an area of 2.54 cm2. Hemispherical X‐ray sources formed by Cu‐doped ZnO nanowire field emitters grown on spherical brass alloy and an Al thin film transmission anode target deposited on a hemispherical quartz glass are successfully fabricated, achieving an operating voltage of 39 kV, a dose rate of 240 µGyair s−1 and a projection X‐ray imaging resolution of 2.8 lp mm−1, demonstrating their promising use in a variety of applications.

High‐resolution strain mapping in a thermionic LaB6 scanning electron microscope

AbstractThe high source stability and brightness of field emission gun equipped scanning electron microscopes (SEM) makes them ideal for high‐resolution digital image correlation (HRDIC). However, their high initial capital cost can be prohibitive for research organisations and groups. Conventional thermionic SEMs using either a tungsten hairpin or LaB6 filament are far more widespread due to their lower cost. Whilst it is understood that overall performance and ultimate resolution are lower than field emission SEMs, we propose that there is no fundamental reason why these instruments are unsuitable for HRDIC. We investigate the use of a LaB6 SEM as a viable tool for HRDIC. We detail the subtleties of performing HRDIC using a LaB6 thermionic source SEM, providing technical recommendations for best practices in using these instruments for strain mapping. The effects of instrument parameters on strain measurement noise are examined, with a focus on parameters of key relevance to in situ and ex situ mechanical testing. Errors in focus and image pixel size are found to be the primary contributors to the strain noise floor values, with stage accuracy being of secondary importance. We present a case study in oxygen‐free high‐conductivity copper, OFHC‐Cu, which is used in the designs of nuclear fusion components as a heat sink interlayer. Heterogeneous strain patterns are observed in this material, with high levels of strain localisation at grain boundaries. Active slip systems are identified using the relative displacement ratio method, demonstrating the quality of these data and the suitability of LaB6 instruments for HRDIC strain mapping, achieving performance approaching that expected of a field emission SEM.

Wafer-scale fabricated on-chip thermionic electron sources based on a suspended Y2O3/TiN filament

Wafer-scale fabricated on-chip thermionic electron sources based on a suspended Y₂O₃/TiN filament

Exploring the Potential of a Thermionic LaB6 Virtual Source Mode Electron Gun for a High Angular Current Density and a Narrow Energy Distribution.

To date, lanthanum hexaboride (LaB6) thermionic electron sources have not been able fully to capitalize on their inherent potential, resulting in an ambiguous position within the application area. Although they exhibit higher brightness compared with a tungsten filament source, they still fall short of the performance of Schottky electron sources. This study aims to explore the capabilities of the LaB6 electron source under different operating conditions to bridge the gap, ultimately to realize its untapped potential. Simulations in virtual source mode indicated enhanced beam brightness and a reduced beam half-angle with an increase the extraction voltage, promising up to tenfold times higher beam brightness compared with the crossover mode. The energy distribution measured using a prelens retarding field energy analyzer revealed an energy distribution of 0.55 eV and a high angular current density of 33 mA/sr in the virtual source mode. Therefore, the virtual source mode of LaB6 can provide a narrow energy distribution akin to that of a ZrO/W Schottky electron gun (1600 K) while having an angular current density over 2,000 times higher. In addition, the stability of the virtual source mode is ±0.022%, while that of the crossover mode is ±0.138%.

Atmospheric Microplasma Treatment Based on Magnetically Controlled Fe–Al Dynamic Platform for Organic and Biomaterials Surface Modification

By exploiting the physical effect of the electron emission from a thermionic source in combination with a magnetically controlled Fe–Al dynamic platform to assist electrical discharge, we generated atmospheric microplasma (AM). The electrical characteristics of microplasma discharge-induced cold atmospheric plasma in combination with a magnetically controlled Fe–Al dynamic platform in open air were evaluated. The surface analysis of organic wheat seeds was investigated at two steps: (1) the coating effect of an Al nanoparticle with an electrons drift toward the seed surface along the direction of an electric field and (2) inelastic collision with secondary electrons moving from the cathode in the presence of an electric field. Using SEM microscopy analysis, it was found that plasma affects seed surface topography and apparent contact angle (ACA). The effect of atmospheric microplasma treatment leads to seed surface modification by the manifestation of fine mesh structures on the seed surface. Well-established AM technology will garner interest in agriculture and biomaterials coatings applications.

Investigation of a novel ring-cusp magnetically confined plasma bridge neutralizer.

The plasma bridge neutralizer (PBN) based on a tungsten filament is a promising technique of a thermionic DC electron source where a hot filament is immersed in an inert gas flow and electrons are "bridged" from a small orifice to the ion beam. PBNs have been widely used in space propulsion and industrial applications due to their relatively simple structure and low power consumption. However, they have well-known disadvantages, namely, low emission current density and short lifetime. In this article, we propose a novel ring-cusp magnetically confined PBN (RCM-PBN) to address these issues. In the RCM-PBN, electrons are confined by a ring-cusp magnetic field, which improves the ionization efficiency and reduces the discharge chamber wall losses. Electrical insulation of the orifice plate from the chamber wall prevents a large number of electrons from being collected by the orifice plate, which greatly improves the extracted electron current. The effects of different operating parameters on the extracted electron current were studied through experiments. It was found that the increase in the extracted electron current with the extraction voltage was related to the anode spot formation. Analysis of the gas utilization factor and electron extraction cost shows that the optimal operating condition was obtained at an argon mass flow rate of 1.2 SCCM and a heater power of 45W. At its optimum, a stable electron current of 1.1A was extracted from the RCM-PBN with a gas utilization factor of 12.8 and an electron extraction cost of 143 W/A.

Key design and operation factors for high performance of C12A7:e-based cathodes

This work, based on an EU-funded project (NEMESIS), is summarising some of the results from the project activities on the research and development on electride-based cathode technology compatible with all kinds of electric propulsion (EP) systems requiring neutralization or electron emission. Further information describing in detail the performed tests and captured measurements can be found in the referenced documents of each section. Different cathode architectures and several emitter configurations with traditional and with alternative propellants are being developed and tested within the project, all of them using C12A7:e-electride material as thermionic electron source. Findings and conclusions derived from these multiple designs are allowing to figure out some of the key factors that determine the best performance of C12A7:e-electride based cathodes. In this work, a discussion of some of these key design and operation factors will be presented based both on the material characterization parameters, and on the performance tests carried out for the different cathode designs.

A Scalable Bacterial Cellulose Ionogel for Multisensory Electronic Skin.

Electronic skin (e-skin), a new generation of flexible electronics, has drawn interest in soft robotics, artificial intelligence, and biomedical devices. However, most existing e-skins involve complex preparation procedures and are characterized by single-sensing capability and insufficient scalability. Here, we report on a one-step strategy in which a thermionic source is used for the in situ molecularization of bacterial cellulose polymeric fibers into molecular chains, controllably constructing an ionogel with a scalable mode for e-skin. The synergistic effect of a molecular-scale hydrogen bond interweaving network and a nanoscale fiber skeleton confers a robust tensile strength (up to 7.8 MPa) and high ionic conductivity (up to 62.58 mS/cm) on the as-developed ionogel. Inspired by the tongue to engineer the perceptual patterns in this ionogel, we present a smart e-skin with the perfect combination of excellent ion transport and discriminability, showing six stimulating responses to pressure, touch, temperature, humidity, magnetic force, and even astringency. This study proposes a simple, efficient, controllable, and sustainable approach toward a low-carbon, versatile, and scalable e-skin design and structure–performance development.

Redesigning the Jefferson Lab Hall A beam line for high precision parity experiments

The Continuous Electron Beam Accelerator Facility (CEBAF) was built with a thermionic electron source and the three original experimental hall lines reflected this. A few years after beam delivery began a parity violation experiment was approved and two polarimeters were installed in the Hall A beam line. The beam raster system was placed after the new Compton polarimeter, before one accelerator quadrupole and four quadrupoles in the new Moller polarimeter. It was very difficult to meet experimental requirements on envelope functions and raster shape with this arrangement so a sixth quadrupole was installed downstream of the Moller polarimeter to provide an additional degree of freedome. All of the parity experiments in Hall A have been run with this still-unsatisfactory configuration. The MOLLER experiment is predicated on achieving a 2% error on a 32 ppb asymmetry. Beam line changes are required to meet the systematic error budget. This paper documents the existing beam line, an interim change which can be accomplished during a annual maintenance down, and the final configuration for MOLLER and subsequent experiments.

Tetrahedron beam imaging with a multi-pixel thermionic emission X-ray source and a photon-counting detector: A benchtop experimental study.

A tetrahedron beam (TB) X-ray system with a linear X-ray source array and a linear detector array positioned orthogonal to each other may overcome the X-ray scattering problem of traditional cone-beam X-ray systems. We developed a TB imaging benchtop system using a linear array X-ray source to demonstrate the principle and benefits of TB imaging. A multi-pixel thermionic emission X-ray (MPTEX) source with 48 focal spots in 4-mm spacing was developed in-house. The X-ray beams are collimated to a stack of fan beams that are converged to a 6-mm wide multi-row photon-counting detector (PCD). The data collected with a sequential scan of the sources at a fixed view angle were synthesized to a 2D radiography image by a shift-and-add algorithm. The data collected with a full rotation of the system were reconstructed into 3D TB CT (TBCT) images using an Feldkamp, Davis, and Kress (FDK)-based computed tomography (CT) algorithm modified for the TB geometry. With an 18.8-cm long source array and a 35-cm long detector array, the TB benchtop system provides a 25-cm cross-sectional and 8-cm axial field of view (FOV). The scatter-to-primary ratio (SPR) was approximately 17% for TB, as compared with 120% for cone beam geometry. The TBCT system enables reconstructions in two-dimensional radiography and three-dimensional volumetric CT. The TBCT images were free of "cupping" artifacts and have similar image quality as diagnostic helical CT. A TB imaging benchtop imaging system was successfully developed with MPTEX source and PCD. Phantom and animal cadaver imaging demonstrated that the TB system can produce satisfactory radiographic X-ray images and 3D CT images with image quality comparable to diagnostic helical CTs.

Thermionic Electron Beam Current and Accelerating Voltage Controller for Gas Ion Sources

Thermionic emission sources are key components of electron impact gas ion sources used in measuring instruments, such as mass spectrometers, ionization gauges, and apparatus for ionization cross-section measurements. The repeatability of the measurements taken with such instruments depends on the stability of the ion current, which is a function, among other things, of the electron beam current and electron accelerating voltage. In this paper, a laboratory thermionic electron beam current and accelerating voltage controller is presented, based on digital algorithm implementation. The average value of the percentage standard deviation of the emission current is 0.021%, and the maximum electron accelerating voltage change versus the emission current is smaller than 0.011% in the full operating range of the emission current. Its application as a trap current or emission current-regulated ion source power supply could be useful in many measuring instruments, such as in microelectromechanical system (MEMS) mass spectrometers as universal gas sensors, where a stable emission current and electron energy are needed.

Quantitative Backscattered Electron Imaging of Bone Using a Thermionic or a Field Emission Electron Source

Quantitative backscattered electron imaging is an established method to map mineral content distributions in bone and to determine the bone mineralization density distribution (BMDD). The method we applied was initially validated for a scanning electron microscope (SEM) equipped with a tungsten hairpin cathode (thermionic electron emission) under strongly defined settings of SEM parameters. For several reasons, it would be interesting to migrate the technique to a SEM with a field emission electron source (FE-SEM), which, however, would require to work with different SEM parameter settings as have been validated for DSM 962. The FE-SEM has a much better spatial resolution based on an electron source size in the order of several 100 nanometers, corresponding to an about 10^5 to 10^6 times smaller source area compared to thermionic sources. In the present work, we compare BMDD between these two types of instruments in order to further validate the methodology. We show that a transition to higher pixel resolution (1.76, 0.88, and 0.57 μm) results in shifts of the BMDD peak and BMDD width to higher values. Further the inter-device reproducibility of the mean calcium content shows a difference of up to 1 wt% Ca, while the technical variance of each device can be reduced to pm 0.17 wt% Ca. Bearing in mind that shifts in calcium levels due to diseases, e.g., high turnover osteoporosis, are often in the range of 1 wt% Ca, both the bone samples of the patients as well as the control samples have to be measured on the same SEM device. Therefore, we also constructed new reference BMDD curves for adults to be used for FE-SEM data comparison.

Characterisation of a thermionic plasma source apparatus for high-density gaseous plasma antenna applications

A thermionic plasma source apparatus has been developed and characterised for high-density gaseous plasma antenna (GPA) applications. The system produces a cylindrical plasma column which is 100 mm long with a diameter of 8 mm and operates with a total plasma power consumption of 70 to 200 W, depending mainly on the DC discharge current. The plasma column electron density and temperature is measured via microwave interferometry and optical emission spectroscopy. The plasma properties are investigated for Ar, Kr and Xe at pressures from 1 to 4 mbar. The system has demonstrated higher electron densities (>1019 m−3) at low pressures (<2 mbar) than has been experimentally achieved before for GPA applications. This could allow for high gain GPA operation comparable to that of conventional metallic antennas. Additionally, the source has demonstrated operation over a wide range of electron densities, from 2 × 1018 to 1 × 1019 m−3, which can allow for frequency hopping. The plasma columns electron temperature remains around 1.5 eV for argon, largely uninfluenced by the pressure or discharge current. These plasma column measurements obtained are used to analyse the plasma properties influence on GPA performance. This analysis indicates that at high density operation, a gain is achieved which is only 22% lower than that of the conventional metallic antenna. Furthermore, the density ranges demonstrated could enable wide-range frequency hopping of over 100 MHz, with a gain greater than 1.3 dBi.

Application of cold filamentary microplasma pretreatment assisted by thermionic emission for potato drying

Cold filamentary microplasma (CFM) pretreatment assisted by thermionic emission (TE) is a promising, cold drying technology for agricultural products. Such novel pretreatment method based on local electroporation process in the air gap. Brief theory and treatment mechanism are explained. A fractional factorial design 33 was used to determine the effect of CFM treatment assisted by TE parameters such as pulse frequency (F = 40, 80 and 120 Hz), pretreatment duration (D = 60, 120 and 180 s) and temperature of thermionic source (T = 700, 850 and 1000 °C) on drying time and drying rate of potato samples. Maximal CFM pretreatment effect was observed at frequency of 80 Hz, treatment duration of 120 s and temperature of thermionic source of 1000 °C, and the corresponding drying rate and drying time were 35·10−5 (kg/kg s−1) and 130 min. The use of CFM treatment had minor effects on the main quality characteristics (total sugar and starch content) of potato samples. Fourier-transformed infrared spectroscopy confirmed the absence of any modifications of functional group composition of potato samples after CFM pretreatment. Results indicate that cold pulsed filamentary microplasma can enhance the drying rate and decrease drying time without changes in quality characteristics. Practical applicationsCold filamentary microplasma pretreatment assisted by thermionic emission can improve the efficiency of potato drying. Furthermore, it has potential application for reducing energy consumption in drying. CFM pretreatment could be potentially applied for agricultural products drying.

Wafer-Scale Fabricated On-Chip Thermionic Electron Sources With an Integrated Extraction Gate

Thermionic electron sources are scaled down to the microscale on a chip and batch fabricated on 4-in silicon wafers by utilizing microfabrication technologies and exploiting carbon nanotubes as microscopic filaments of thermionic electron emission. The microfabricated on-chip thermionic electron sources not only satisfy the metrics of compactness and ease of batch fabrication, but also exhibit the advantages of good performance reproducibility (±6.9% variation over 100 test cycles under a driven voltage of 3.5 V) and high emission stability (fluctuation < 5% for emission current level of ≈10−8 A over 900 s) under a relatively low vacuum condition (10−4–10−2 Pa). Furthermore, to extract electrons and tune emission current, an extraction gate with a mesh is monolithically integrated with the thermionic electron sources using anodic bonding technique. The integrated electron sources exhibit a strong gate controllability and a considerable electron transmission ratio of ≈76% through the extraction gate. All these results make our devices a promising type of on-chip electron source in the applications of miniature vacuum electronic devices/systems.

Comparison of thermionic filament and carbon nanotube field emitter-based electron ionization sources in cycloidal coded aperture mass analyzers

This work compares the coded aperture imaging performance of thermionic filament and carbon nanotube (CNT) field emitter-based electron sources in cycloidal-coded aperture mass spectrometers. The use of spatially coded apertures in mass spectrometry enables miniaturization by improving throughput without sacrificing resolution. CNT-based electron ionization sources for mass spectrometers provide several potential benefits over conventional thermionic emitters, including low voltage and low power consumption, room temperature operation, long lifetime, and ability to emit electrons in a pulsed mode. However, spatiotemporal variation in electron emission from CNTs is a major disadvantage. In this study, electron emission stability and spatiotemporal stability of the coded aperture image were compared for coded aperture cycloidal mass analyzers with either a CNT-based ion source or a thermionic filament-based ion source. We found that the thermionic filament-based ion source produced a significantly more stable coded aperture image than the CNT based ion source. The aperture image fluctuations in the CNT-based source are likely a result of adsorption and desorption of molecules on the CNT surface that cause local work function changes and induce spatiotemporal variation in electron emission and subsequent ion generation.

First off-line tests and performance of the Notre Dame multi-reflection time-of-flight mass spectrometer

A multi-reflection time-of-flight mass spectrometer (MR-TOF) will be a critical component for quickly removing radioactive contaminants produced at the future “N = 126 factory” addition to ATLAS at Argonne National Laboratory (ANL). This unique thermalized ion beam facility will employ multi-nucleon transfer reactions to produce very neutron-rich isotopes relevant to the astrophysical r-process. Ion beams produced at this facility will include isobaric contaminants, while precision measurements of such rare isotopes typically require highly purified samples. Hence, to tackle this issue an MR-TOF has been built and commissioned at the University of Notre Dame in an off-line test setup comprising a thermionic source and a Bradbury-Nielsen gate (BNG) to create the ions bunches to be purified. Resolving power above 30,000, with a corresponding efficiency of 35%, has been achieved. Most of the ion beam losses could be the result of the large radial divergence of ion bunches produced by the BNG, hence greater efficiency and resolving power are expected once the MR-TOF is connected to an radiofrequency quadrupole (RFQ) cooler and buncher at ANL.

Confined focused sheet beam flow of a thermionic linear electron source

A magnetically confined sheet beam has been designed and tested for its uniform transmission. The beam is fully immersed in a uniform magnetic field of 50 Gauss which bends and focuses the beam throughout in a uniform laminar flow at 180̂. A sheet beam of uniform cross section (0.35 cm × 12.5 cm) successfully has been tested; the width of the beam is many times the thickness. The gun is designed and simulated in CST software. The beam is uniform throughout with parameters; current density, emittance and perveance values; 1.04 A/cm2, 14 π-mm-mR and 5 μAV−3/2, respectively. The simulation and test results are in agreement. The first application is the evaporation of refractory metals for coating in the field of nanotechnology and also expected to be used in klystrons for advanced particle accelerators and colliders at higher acceleration potentials.

A Fully Closed Nano-Focus X-Ray Source With Carbon Nanotube Field Emitters

We developed a fully closed nano-focus X-ray source using carbon nanotube (CNT) field emitters. The nano-focus X-ray source includes a fully vacuum-sealed CNT Electron-gun (E-gun) tube and E-beam-focusing modules consisting of electrostatic and magnetic lenses, facilitating very compact and high-resolution X-ray imaging. The paste-printed CNT emitters were prepared in a small pattern as an electron source, and the entire components, including the CNT emitter module, Cu tubes, collimators, and transmissive anode target, were specially brazed at an elevated temperature, resulting in a very compact E-gun tube. The CNT emitter showed a stable and reliable emission current with its density of over 300 mA/cm2 even in the vacuum-sealed E-gun tube. With the anode grounded and the CNT emitter module biased to negative high voltages, we achieved a considerably magnified x-ray image of a several hundred nanometer resolution. The fully vacuum-sealed CNT E-gun tube along with the magnetic lens module can offer much more compact, easily maintainable, high-resolution X-ray imaging compared with conventional open-type thermionic X-ray sources.

Operation of an RF Modulated Thermionic Electron Source at TRIUMF

The electron source in the TRIUMF ARIEL project is a gridded dispenser cathode. The cathode is biased at -300kV, and the grid requires a RF control signal of up to 150V at 650 MHz. The required RF power is approximately 20 W and is provided by an RF amplifier located outside the gun vessel. This RF power is coupled into the gun circuit through a ceramic transmission line. The design of this ceramic transmission line, as well as the impedance transformation circuit which provides both the impedance matching and the dc powers to the gun assembly are described.