Termination Area Research Articles

Safety Evaluation of Joint and Conventional Lane Merge Configurations for Freeway Work Zones

Inefficient operation of traffic in work zone areas not only leads to an increase in travel time delays, queue length, and fuel consumption but also increases the number of forced merges and roadway accidents. This study evaluated the safety performance of work zones with a conventional lane merge (CLM) configuration in Louisiana. Analysis of variance (ANOVA) was used to compare the crash rates for accidents involving fatalities, injuries, and property damage only (PDO) in each of the following 4 areas: (1) advance warning area, (2) transition area, (3) work area, and (4) termination area. The analysis showed that the advance warning area had higher fatality, injury, and PDO crash rates when compared to the transition area, work area, and termination area. This finding confirmed the need to make improvements in the advance warning area where merging maneuvers take place. Therefore, a new lane merge configuration, called joint lane merge (JLM), was proposed and its safety performance was examined and compared to the conventional lane merge configuration using a microscopic simulation model (VISSIM), which was calibrated with real-world data from an existing work zone on I-55 and used to simulate a total of 25 different scenarios with different levels of demand and traffic composition. Safety performance was evaluated using 2 surrogate measures: uncomfortable decelerations and speed variance. Statistical analysis was conducted to determine whether the differences in safety performance between both configurations were significant. The safety analysis indicated that JLM outperformed CLM in most cases with low to moderate flow rates and that the percentage of trucks did not have a significant impact on the safety performance of either configuration. Though the safety analysis did not clearly indicate which lane merge configuration is safer for the overall work zone area, it was able to identify the possibly associated safety changes within the work zone area under different traffic conditions.

Amphibolitization within the lower crust in the termination area of the Godzilla Megamullion, an oceanic core complex in the Parece Vela Basin

AbstractGabbroic rocks and amphibolites were collected from the KR03‐01‐D10 dredge site located on the West Arm Rise of the Godzilla Megamullion, close to the Parece Vela Rift which appears to correspond to the termination area of a detachment fault, the Philippine Sea. The gabbroic rocks and amphibolites reveal the occurrence of a high hydrothermal activity in the lower crust close to a paleo‐ridge. In the gabbroic rocks, plagioclase compositions of both porphyroclasts and matrix were transformed into sodium‐rich compositions close to albite. Amphiboles are of secondary rather than igneous origin based on their microstructural occurrences. In the amphibolites, anorthite contents of porphyroclasts and matrix plagioclase are relatively lower than those of the gabbroic rocks, whereas the chemical compositions of amphibole within the amphibolites are similar to those of amphibole within the gabbroic rocks. Amphibolites represent the product of retrograde metamorphism associated with hydrothermal alteration of the gabbroic body by the reaction: clinopyroxene + calcic plagioclase + fluid → amphibole + sodic plagioclase. The estimated temperatures of the amphibolites derived from the amphibole thermobarometer and the gabbroic rocks derived from the hornblende–plagioclase geothermometer show ∼700–950°C and 650–840°C, respectively. The hydrothermal alteration recorded in the gabbroic rocks possibly occurred under high‐T conditions; the rocks were then metamorphosed to the amphibolites during a retrogressive stage. Our study indicates that amphibolitization took place with various degrees of deformation. It may imply that the hydrothermal activity increased as the Godzilla Megamullion developed as an oceanic core complex in the paleo‐ridge.

Improved Bond reliability through the use of Auxiliary Wires (Security Bumps and Stand-Off Stitch)

Whether the need is due to poorly bondable materials, non-flat bonding surfaces, odd packaging situations, or just the need for high reliability; the integrity of a wire bond interconnect can usually be greatly improved through the proper use of Auxiliary Wires. Auxiliary Wires are defined as Security Wires, Security Bumps, or Stand-Off Stitch (aka Stitch on Bump). The old stand-by Security Wire has been an asset for several decades, however, this is being replaced by Security Bumps which require a smaller second bond termination area. Further, Stand-Off Stitch (SOS) has many more applications and also has many side benefits that could be incorporated into a circuit design for better wire strength properties, fewer interconnects (die to die bonding), and lower loops. Stand-Off Stitch bonding involves the placement of a ball bump at one end of the wire interconnect, then placing a wire with another ball at the other end of the interconnect and stitching off the wire on the previous placed ball bump. This results in a near homogeneous stitch bond interconnect to the bump with an inherent improvement in stitch bond pull strength. Another use for SOS is Reverse Bonding (Stitch bond on bump on die bond pad) often resulting in a lower loop profile than standard forward wire loop and the loop is stronger because the wire hasn't been work annealed above the ball (in the Heat Affected Zone). A major impediment to the implementation of SOS is the retraining of visual inspectors and the approval of quality departments.

Interretinal transduction of injury signals after unilateral optic nerve crush

In this study, we report that partial unilateral optic nerve crush in the rat affects the number of retinal ganglion cells of the contralateral eye still in continuity with the ipsilateral superior colliculus. The reduction in cell number of the uncrossed retinal projection was accompanied by a microglia response and could be prevented by the local intravitreal application of the anti-inflammatory agent dexamethasone. Interestingly, the level of neuronal activity after optic nerve crush as evidenced by thallium autometallography was enhanced in the termination area of the uncrossed projection, the rostro-medial superior colliculus, suggesting that a dying-back mechanism is not involved. We propose that injury signals from the damaged optic nerve and retina are transduced to the unaffected eye.

Postnatal changes in the Rexed lamination and markers of nociceptive afferents in the superficial dorsal horn of the rat

In this study, we investigated postnatal changes in Rexed's laminae and distribution of nociceptive afferents in the dorsal horn of the rat lumbar spinal cord at postnatal days 0, 5, 10, 15, 20, and 60. Transverse sections of the L4-L5 segments were processed for triple labeling with isolectin B4 (IB4)-binding as a marker of nonpeptidergic C-fibers, calcitonin gene-related peptide (CGRP) immunoreactivity to label peptidergic nociceptive afferents, and a fluorescent Nissl stain to visualize cells and lamination at different stages of postnatal development. The Nissl staining revealed that the thickness of lamina I (LI) and outer lamina II remained mostly unchanged from birth until adulthood. CGRP afferents terminated mostly in LI and the outer two-thirds of lamina II, whereas the termination area of fibers binding IB4 was centered on the middle one-third of lamina II at all ages studied. In absolute values, the overall width of the bands of intense CGRP and IB4 labeling increased with age but decreased as a percentage of the overall thickness of the dorsal horn with maturation. The overlap of CGRP termination area with that of IB4 afferents increased with age. The consequences of these findings are twofold. First, the size of the different laminae does not grow evenly across the dorsal horn. Second, CGRP and IB4 labeling cannot be considered per se to be reliable markers of lamination during development. These findings have implications for comparing data obtained in immature and mature tissues with respect to localization of structures in the dorsal horn.

Design Changes and Impact on the Production of the Non-Planar Coils for the W-7X Experiment

The Max-Planck-Institut fÜr Plasmaphysik is building the stellarator fusion experiment WENDELSTEIN 7-X (W7-X) at the branch institute in Greifswald, Germany. The 50 non-planar superconducting coils are currently manufactured by industry and use a specially developed NbTi cable-in-conduit conductor. The manufacture of the coils includes the conductor, winding of the conductor, vacuum pressure impregnation as well the embedding of the winding pack into a cast steel casing, the final machining and the installation of the helium cooling system on the casing. Design changes became necessary during production in the connection areas of the casings due to more detailed design and structural analysis. In addition, the insulation and the welds in the termination area need to be improved. New quench detection cables were qualified. LINAC inspections allowed to check the presence of casting defects in the thick casings. Additionally high voltage tests in vacuum under Paschen-minimum conditions turned out to be a very sensitive inspection method to check the integrity of the electrical insulation.

An Improved Junction Termination Design Employing Shallow Trenches and Field Limiting Rings for Power Devices

A new junction termination method employing shallow trenches filled with silicon dioxide and field limiting rings (FLRs) for 1200 V power device applications is proposed to decrease the junction termination area without sacrificing the breakdown voltage and any additional fabrication processes. The proposed structure was analyzed and verified by numerical simulations and experiments. The two-dimensional numerical simulation results show that two electric field peaks between the field limiting rings appear in the proposed structure due to the shallow trench filled with silicon dioxide while the conventional FLR structure shows a single electric field peak between the field limiting rings. The proposed structure achieves a uniform electric field distribution and increases a breakdown voltage. The junction termination area of the proposed structure is decreased at the same breakdown voltage due to the low dielectric constant of the silicon dioxide in the trench. The experimental results show that the junction termination length of the proposed structure is 15–21% lower than that of the conventional FLR. The proposed structure achieves the high breakdown voltage, which is 80% of the ideal parallel-plane junction breakdown voltage.

Connections of the superior vestibular nucleus with the oculomotor and red nuclei in the rat: An electron microscopic study

Phaseolus vulgaris leucoagglutinin (PHA-L) was injected into the individual vestibular nuclei of the rat to study their efferent connections. One of the major differences between the connections of these nuclei was found at the level of the mesencephalon: the eye-moving cranial nerve nuclei received the densest projection from the superior vestibular nucleus (SVN). In the present electron microscopic study, we have found that terminals of SVN origin established symmetric synaptic contacts in the oculomotor nucleus. More than two-thirds of PHA-L-labeled boutons terminated on dendrites, the rest of them established axosomatic contacts. Most of the labeled terminals were GABA-positive, supporting the results of previous physiological experiments, which showed inhibitory effects. In the mesencephalon, the other termination area was found in the red nucleus. The PHA-L-labeled boutons of SVN origin were in close contact with the perikarya and proximal dendrites of the magnocellular part of the red nucleus. The types of synaptic contacts and distribution of terminals of SVN origin were similar to those found in the oculomotor nucleus. Our results indicate that the SVN can modify the activity of the cerebellorubral and corticorubral pathways, exerting inhibitory action on the neurons of the red nucleus.

Validation of a Driving Simulator for Work Zone Design

The research project aimed at calibrating and validating the driving simulator of the European Interuniversity Research Center for Road Safety to enable its use for design and verification of the effectiveness of temporary traffic signs on highways. The research was developed through the following steps: ( a) a survey of speed measurements on highways next to a work zone of medium duration, ( b) reconstruction in virtual reality of the real situation by using the driving simulator and subsequent running of a series of driving tests, and ( c) statistical analysis of the field speeds and of the speeds from driving simulations for validation of the simulator. The surveyed work zone was located on Highway A1 from Milan to Naples, Italy. Speed measurements were conducted with a laser speed meter in the transition area, the activity area, and the termination area, and in the advance warning area speeds were shot with a camera from an overpass. Speed data from the field and the simulator were analyzed by using the bilateral Z-test for non-matched samples to determine whether drivers responded differently in the simulator compared with their response during the real driving experience. The activity carried out revealed that differences between the speeds observed in the real situation and those measured with the simulator were not statistically significant.

Validation of a Driving Simulator for Work Zone Design

The research project aimed at calibrating and validating the driving simulator of the European Interuniversity Research Center for Road Safety to enable its use for design and verification of the effectiveness of temporary traffic signs on highways. The research was developed through the following steps: (a) a survey of speed measurements on highways next to a work zone of medium duration, (b) reconstruction in virtual reality of the real situation by using the driving simulator and subsequent running of a series of driving tests, and (c) statistical analysis of the field speeds and of the speeds from driving simulations for validation of the simulator. The surveyed work zone was located on Highway A1 from Milan to Naples, Italy. Speed measurements were conducted with a laser speed meter in the transition area, the activity area, and the termination area, and in the advance warning area speeds were shot with a camera from an overpass. Speed data from the field and the simulator were analyzed by using the bilateral Z-test for nonmatched samples to determine whether drivers responded differently in the simulator compared with their response during the real driving experience. The activity carried out revealed that differences between the speeds observed in the real situation and those measured with the simulator were not statistically significant.

Course of spinocerebellar axons in the ventral and lateral funiculi of the spinal cord with projections to the posterior cerebellar termination area: an experimental anatomical study in the cat, using a retrograde tracing technique

The course of retrogradely labeled spinocerebellar fibers in the ventral and lateral funiculi of the spinal cord was studied following injections of wheat germ agglutinin-conjugated horseradish peroxidase into the posterior spinocerebellar termination area in the cat. Fibers labeled from unilateral injections into the paramedian lobule were found on the same side in the dorsal part of the lateral funiculus (DLF), corresponding to the dorsal spinocerebellar tract (DSCT), but contralaterally in the ventral part of the lateral funiculus (VLF) and in the ventral funiculus (VF), corresponding to the ventral spinocerebellar tract (VSCT). Following injections into the posterior vermis, labeled fibers were less numerous. Most of them were found in the DSCT and only very few in the VSCT. Previously identified cells of origin of these spinocerebellar tracts were labeled in these experiments and counted. They correlated well with the extents and the locations of the injections that had been made into the two termination sites. These results represent novel detailed information on the location of axons projecting to the two main posterior spinocerebellar termination sites in the spinal white matter in the cat.

Compartmentation of the reeler cerebellum: Segregation and overlap of spinocerebellar and secondary vestibulocerebellar fibers and their target cells

The cerebellum of the reeler mutant mouse has an abnormal organization; its single lobule is composed of a severely hypogranular cortex and a central cerebellar mass (CCM) consisting of Purkinje cell clusters intermixing with the cerebellar nuclei. As such the reeler represents an excellent model in which to examine the effect of the abnormal distribution of cerebellar cells on afferent-target relationships. To this effect we studied the organization of the spinocerebellar and secondary vestibulocerebellar afferent projections in homozygous reeler mice (rl/rl) using anterograde tracing techniques. Spinal cord injections resulted in labeled spinocerebellar mossy fiber rosettes in specific anterior and posterior regions of the cerebellar cortex. Some vestiges of parasagittal organization may be present in the anterior projection area. Within the CCM, labeled fibers appeared to terminate on distinct groups of Purkinje cells. Thus, the spinocerebellar mossy fibers seem to form both normal and heterologous synapses in the reeler cerebellum. Secondary vestibular injections resulted in both retrograde and anterograde labeling. Retrograde labeling was seen in clusters of Purkinje cells and cerebellar nuclear cells; anterograde labeling was distributed in the white matter and in specific regions of the anterior and posterior cortex of the cerebellum. The labeled spinocerebellar and secondary vestibulocerebellar afferents overlapped in the anterior region but in the posterior region the vestibulocerebellar termination area was ventral to the spinocerebellar area. An area devoid of labeled terminals was also observed ventral to the posterior secondary vestibulocerebellar termination field. Using calretinin immunostaining it was determined that this area contains unipolar brush cells, a cell type found primarily in the vestibulocerebellum of normal mice. Our data indicate that despite of the lack of known landmarks (fissures, lobules) the spinocerebellar and vestibulocerebellar afferent projections in the reeler cerebellum do not distribute randomly but have specific target regions, and the position of these regions, relative to each other, appears to be conserved. Two caveats to this were the finding of overlapping terminal fields of these afferents in the anterior region, and a posteroventral region that contains unipolar brush cells yet is devoid of secondary vestibulocerebellar afferents. The distribution of Purkinje cells and cerebellar nuclear cells is not random either; those that give rise to cerebellovestibular efferents form distinct groups within the central cerebellar mass.

A New Junction Termination Method Employing Shallow Trenches Filled With Oxide

A new junction termination method employing shallow trenches filled with oxide, which successfully decreased the junction termination area, is proposed and fabricated without any complicated process such as Si-deep etching. Shallow trenches between the floating field limiting rings successfully redistributed the single electric field peak into two peaks so that the breakdown voltage could be increased with the same junction termination area. The experimental results show that the proposed method decreased the junction termination area by more than 25% compared to a conventional field limiting ring structure when breakdown voltages are equal.

Distribution of dendrites of descending neurons and its implications for the basic organization of the cockroach brain.

To determine precisely the brain areas from which descending neurons (DNs) originate, we examined the distribution of somata and dendrites of DNs in the cockroach brain by retrogradely filling their axons from the cervical connective. At least 235 pairs of somata of DNs were stained, and most of these were grouped into 22 clusters. Their dendrites were distributed in most brain areas, including lateral and medial protocerebra, which are major termination areas of output neurons of the mushroom body, but not in the optic and antennal lobes, the mushroom body, the central complex, or the posteroventral part of the lateral horn. The last area is the termination area of major types of olfactory projection neurons from the antennal lobe, i.e., uni- and macroglomerular projection neurons, so these neurons have no direct connections with DNs. The distribution of axon terminals of ascending neurons overlaps with that of DN dendrites. We propose, based on these findings, that there are numerous parallel processing streams from cephalic sensory areas to thoracic locomotory centers, many of which are via premotor brain areas from which DNs originate. In addition, outputs from the mushroom body, central complex, and posteroventral part of the lateral horn converge on some of the premotor areas, presumably to modulate the activity of some sensorimotor pathways. We propose, based on our results and documented findings, that many parallel processing streams function in various forms of reflexive and relatively stereotyped behaviors, whereas indirect pathways govern some forms of experience-dependent modification of behavior.

Differences in lesion-induced hippocampal plasticity between mice and rats

We studied the differences between mice and rats in lesion-induced sprouting in the hippocampus. The entorhinal cortex was unilaterally lesioned with ibotenic acid in adult, female mice and rats. Four weeks later the subsequent axonal sprouting in the dentate gyrus was analysed, by measuring the density of the synaptophysin immunohistochemical and acetylcholinesterase histochemical staining in the termination area of the entorhinal cortex axons. The data demonstrate that both mice and rats display a significantly increased density of staining for synaptophysin and acetylcholinesterase in the molecular layer of the dentate gyrus, indicative of axonal sprouting. Both species also show an upregulation in the density of staining for acetylcholinesterase in the molecular layer of the dentate gyrus. Further, rats, but not mice, show a significant upregulation of synaptophysin staining in stratum lacunosum moleculare of CA1 following the lesions. However, whereas rats show significant shrinkage of the molecular layer of the dentate gyrus, mice do not show any shrinkage of that layer following entorhinal cortex lesions. Taken together, these data indicate that whereas the process of reinnervation in the hippocampus is similar between the mouse and the rat, the hippocampal response to denervation shows clear differences between these two species.

Transgenic mice expressing the human presenilin 1 gene demonstrate enhanced hippocampal reorganization following entorhinal cortex lesions

We have examined the effects of the presence of the mutated human presenilin 1 gene (M146L; hps1∗) on lesion-induced sprouting in the hippocampus of the mouse (C57/CBA). The entorhinal cortex was unilaterally lesioned with ibotenic acid in adult, male mice. Four weeks later the subsequent axonal sprouting in the dentate gyrus was analysed, by measuring the density of the synaptophysin immunocytochemical staining in the termination area of the entorhinal cortex axons. The data demonstrate that mice expressing either the human presenilin 1 gene (hps1) or the hps1∗ gene display a significantly increased density of immunocytochemical staining for synaptophysin, indicative of axonal sprouting, compared to the control mice. No (or a very small) sprouting response is observed in mice expressing the normal mouse ps1 gene. Taken together, these data indicate that the presence of a human ps1 gene, normal or with an Alzheimer’s disease mutation, leads to enhanced plasticity in the mouse brain.

Primary afferent fibers establish dye-coupled connections in the frog central nervous system

Neurobiotin and Lucifer yellow, indicators of gap junctional coupling, were applied to primary afferent fibers of the frog. Following application of tracers to cervical or lumbar dorsal root fibers, a large number of labeled granule cells were detected in the corpus cerebelli, the brainstem, and the spinal cord. The vestibular nerve was found to be in dye-coupled connection with the granule cells of the auricular lobe of the cerebellum. After application of the tracers to the trigeminal nerve, elicited dye-coupled neurons located mainly in the termination area of the descending limb of the mesencephalic trigeminal nucleus. In control experiments with biotinylated dextrane amine, only primary afferent fibers were labeled. Our results suggest that gap junctional coupling exists between primary afferent fibers and their postsynaptic targets in the frog.

A novel metal field plate edge termination for power devices

A new termination structure, which incorporates metal field plate over every alternate low doped p well ring is presented for planar power devices. This structure is designed to control the punch through voltage between rings to increase the blocking voltage capability while reducing the edge termination area. Measured results based on a 2kV process technology are consistent with those of numerical modelling and demonstrate that 88% of the plane parallel breakdown voltage can be achieved within 600μm while maintaining less sensitivity to fixed oxide charge.

Dopamine Selectively Inhibits the Direct Cortical Pathway to the CA1 Hippocampal Region

The perforant path input (pp) is a major direct source of specific sensory information for the CA1 hippocampal region. The termination area of this pathway, the stratum lacunosum-moleculare, has the highest concentration of dopamine receptors in the hippocampus. We have examined the properties of the pp input and its modulation by dopamine. The input is glutamatergic and has a larger NMDA component than the Schaffer collateral (sc) input. Dopamine strongly inhibits the response to pp stimulation (IC50 approximately 3 microM) but not the response to sc stimulation. Dopamine reduces both the NMDA and AMPA components of transmission at the pp and increases paired-pulse facilitation. In the sc, the NMDA component but not the AMPA component is decreased, and paired-pulse facilitation is not affected. The effect of dopamine on the pp does not depend on GABAA inhibition but is reduced by the antagonists of both D1 and D2 families of dopamine receptors. The effect is not completely blocked by the combination of D1 and D2 antagonists, but is completely blocked by the atypical neuroleptic clozapine. Our results provide the first evidence for strong dopaminergic control of transmission in the perforant path. By inhibiting this pathway, dopamine hyperfunction and/or NMDA hypofunction abnormalities implicated in schizophrenia may isolate CA1 from its main source of sensory information.

Distinct cell groups in the lumbosacral cord of the cat project to different areas in the periaqueductal gray.

The periaqueductal gray (PAG) is involved in aggressive and defensive behavior, micturition, and lordosis. Especially for the latter two functions, PAG afferents from the lumbosacral cord are of vital importance because, in addition to information regarding homeostasis and thermoregulation, they convey information from the pelvic viscera and sex organs. In the present retro- and antero-grade tracing study, the projection patterns of different lumbosacral cell groups in the PAG were determined. In the retrograde study, wheatgerm agglutinin-horseradish peroxidase (WGA-HRP) injections were made in the PAG and/or adjacent tegmentum, and in the anterograde study, WGA-HRP was injected in different lumbosacral segments. The results revealed that lumbosacral-PAG neurons could be divided into three groups. The first and largest group was present in lumbar 7-sacral 3 segments (L7-S3) and consisted of small, oval, and fusiform neurons. It extended from the dorsolateral part of lamina I in L7, along the lateral part of the dorsal horn in S1, and into lamina V of S2. In the lateral part of S2, some of its neurons formed clusters with intervals of +/- 230 microns. The location of the first group overlapped extensively with the termination area of pelvic and pudendal afferents. The main midbrain target of the first group was the medial part of the lateral PAG. The second group consisted of small to large multipolar neurons in laminae VIII and medial VII of caudal L6, L7, and rostral S1. This group projected strongly to a distinct region in the lateral part of the lateral PAG and the laterally adjacent tegmentum. About 10% of the labeled neurons did not fit in the two groups. They were evenly distributed throughout lumbar 4-coccygeal 3 segments (L4-Co3) and consisted of large multipolar lamina V neurons and small lamina I neurons that projected diffusely to the lateral and dorsal PAG. The large lamina V neurons also targeted the laterally adjacent tegmentum. The possible involvement of the lumbosacral-PAG projections in micturition, lordosis, and defensive and aggressive behavior is discussed.