Increase In Temperature Research Articles

Current and Future Distribution of the Cataglyphis nodus (Brullé, 1833) in the Middle East and North Africa

Climate change is a major threat to the Middle East and North Africa (MENA) region, which can cause significant harm to its plant and animal species. We predicted the habitat distribution of Cataglyphis nodus (Brullé, 1833) in MENA using MaxEnt models under current and future climate conditions. Our analysis indicates that the cooler regions of the MENA are projected to experience temperature increases of 1–2 °C by 2040 and 2–4 °C by the 2070s. Similarly, the warmer regions may anticipate rises of 0.5–2 °C by 2040 and 2–4 °C by the 2070s. MaxEnt model results for the current climate show good agreement with observations (mean area under the curve value of 0.975 and mean true statistical skill value of 0.8), indicating good potential habitat suitability for C. nodus. Significant factors affecting habitat suitability are elevation, mean monthly precipitation of the coldest quarter, temperature seasonality, and precipitation amount of the driest month. The research predicts that under Shared Socioeconomic Pathway (SSP) 1.2.6, the habitat suitability area may increase by 6% in 2040, while SSP 3.7.0 (0.3%) and SSP 5.8.5 (2.6%) predict a decrease. For 2070, SSP 5.8.5 predicts a 2.2% reduction in habitat suitability, while SSP 1.2.6 (0.4%) and SSP 3.7.0 (1.3%) predict slight increases. The results provide insight into the potential impacts of climate change on the species and regional biodiversity changes associated with the projected species distribution.

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

In order to optimize the heating schedule before forging and improve the breaking and deformation effects of carbides in high‐speed steel, it is of great significance to study the transformation of M2C carbides at high temperatures. The evolution of carbides in the industrial‐grade American Iron and Steel Institute M35 steel produced by electroslag remelting (ESR) is analyzed and observed using thermodynamic calculations and experimental methods. The results indicate that the carbides in the ESR ingot are mainly MC and M2C, and the microstructures of M2C carbides with the highest volume fraction are lamellar and brain like. As the heating temperature increases and holding time prolongs, the lamellar M2C carbides gradually transform into MC and M6C carbides, accompanied by protrusion, dissolution, separation, and spheroidization of the microstructure, until significant coarsening occurs at 1180 °C for 90 min. The newly transformed carbides are embedded and stacked with each other, occupying the original position of M2C carbides. Based on the theories of Gibbs free energy and atomic diffusion, the evolution mechanism of M2C carbides is discussed. Ultimately, the appropriate heating schedule is proposed, and it is validated by combining the characteristics of carbides after forging.

Nature of electrically detected magnetic resonance in highly nitrogen-doped 6H -SiC single crystals

This work focuses on unraveling electron paramagnetic resonance (EPR) and electrically detected magnetic resonance (EDMR) properties of n-type 6H silicon carbide (SiC) single crystals with high concentrations of uncompensated nitrogen (N) donors, which is essential for fundamental understanding of spin-related phenomena, developing spin-based devices, optimizing materials and devices, and advancing research in quantum information and spintronics. Utilizing low-temperature multifrequency EPR spectroscopy (9.4–395.12 GHz), we identified two intense signals labeled as S line and S1 line in the 6H-SiC crystals with ND–NA≈8×1018 and 4×1019cm−3. In addition, in 6H-SiC crystals with ND–NA≈8×1018cm−3, a low-intensity triplet from N donors substituting the quasicubic “k2” nonequivalent position (Nk2) was observed. The S line [g⊥=2.0029(2),g∥=2.0038(2)] was assigned to the exchange interaction of conduction electrons and Nk2, while the S1 line [g⊥=2.0030(2),g∥=2.0040(2)] is caused by the exchange spin coupling of localized N donors at the “k1” and “k2” positions. The S1 line was observed in high-frequency EDMR spectra of 6H-SiC with ND–NA≈8×1018cm−3, and its emergence was explained by an enhancement of the hopping conductivity due to the EPR-induced temperature increase mechanism. No EDMR spectra were found to occur in the 6H-SiC crystals with ND–NA≈4×1019cm−3, which is close to the critical donor concentration value for a semiconductor-metal transition. Thus it can be concluded that this N donor concentration is too high for the appearance of spin-dependent scattering and too low for the emergence of EPR-induced hopping mechanisms in 6H-SiC. Published by the American Physical Society 2024

Global sustainability scenarios lead to regionally different outcomes for terrestrial biodiversity

Abstract Mitigating climate change (CC) and reversing biodiversity decline are urgent and interconnected global priorities. Strategies to address both crises must consider the relationships, synergies and trade-offs between key response measures, including sustainable production and consumption patterns, protected areas (PAs) and climate mitigation policy (CP). In this paper, we review a large set of scenarios (n = 96) from the Integrated Model to Assess the Global Environment (IMAGE) describing future development of land use, greenhouse gas emissions and their impact on CC and biodiversity. We calculate the global mean temperature increase (GMTI) and the Mean Species Abundance (MSA) of plants, a metric indicative of local terrestrial biodiversity intactness. The set includes scenarios with and without specific CP to address CC, PA for biodiversity and demand and supply sustainability measures such as increased energy efficiency and reduced meat consumption. Our findings indicate that scenarios with integrated measures can prevent biodiversity loss at the global scale, yet with clear regional differences. By 2050, 15 out of 30 (50%) scenarios with at least 30% of global land as PAs show positive MSA changes in grasslands and tropical non-forests (Grass & TnF), but only 1 (3%) does so in tropical forests (TF). We demonstrate that pasture and food/feed crops are the main drivers of MSA loss in Grass & TnF and that scenarios with high levels of PAs prevent land conversion and increase biodiversity. By 2100, 28 out of 46 (60%) scenarios with mitigation measures to restrict CC to 2 °C or less in 2100 result in positive MSA changes in TF, but only 13 (28%) do so in Grass & TnF, reflecting the larger impacts of land use change in the latter region. These results underscore the importance of time and regionally-tailored approaches to address the biodiversity and CC crises.

Effects of Thermal Exposure Temperature on Room-Temperature Tensile Properties of Ti65 Alloy.

As a critical material for high-temperature components of aero-engines, the mechanical properties of Ti65 alloy, subjected to high-temperature and long-term thermal exposure, directly affect its service safety. The room-temperature tensile properties of the Ti65 alloy after thermal exposure to temperatures ranging from 450 °C to 650 °C for 100 h were investigated. The results indicate that as the thermal exposure temperature increases, the strength of Ti65 alloy initially increases and then decreases, while ductility exhibits a decreasing trend. The strength of the thermally exposed alloy positively correlates with the size and content of the α2 phase. The ductility of the thermally exposed alloy is comprehensively influenced by the surface oxidation behavior, α2 phase, and silicides. After the prolonged thermal exposure, stress concentration at the crack tips within the oxide layer was enhanced with the increased thickness of the surface TiO2 oxide layer, leading to premature fracture due to reduced alloy ductility. Furthermore, the α2 phase in the matrix promotes the planar slip of dislocations, while silicides at the α/β phase boundaries hinder dislocation motion, causing dislocation pile-ups. Both behaviors facilitate crack nucleation and deteriorate alloy ductility.

Effect of Interface Defects on the Electric–Thermal–Stress Coupling Field Distribution of Cable Accessory Insulation

The combined insulation interface of a high-voltage cable and accessories is the weakest part of a cable system. In this paper, the parameters of the dielectric constant, thermal conductivity, and elastic modulus of cross-linked polyethylene (XLPE) and silicone rubber (SIR) are obtained experimentally. On this basis, the model of a specific type of 110 kV cable and prefabricated insulation joint is established. A simulation of the electric–thermal–stress coupling field in the presence of typical defects in the main insulation–inner semi-conductive (SEMI) shielding layer (XLPE/SEMI interface) and the main insulation–silicone rubber insulation layer (XLPE/SIR interface) is studied. The simulation results show that at the XLPE/SIR interface, the electric field distortion caused by bubble defects reached 20.17 kV/mm, and the temperature rose to 56.15 °C. The effect of air-gap defects on the interface is similar to that of bubble defects. In addition, the semi-conductive impurity defects induced an increase in temperature to 56.82 °C and an increase in stress to 0.32 MPa. At the XLPE/SEMI interface, the electric field distortion induced by bubble defects was 19.98 kV/mm, and the temperature rose to 61.72 °C. The electric field distortion caused by metallic and semi-conductive defects was 8.44 kV/mm and 8.64 kV/mm, respectively. This study serves as a reference for the fault analysis and the operation and maintenance of cable accessories.

Heat Shock Protein 70 Genes Are Involved in the Thermal Tolerance of Hippodamia variegata

Previous studies have shown that the survival and reproduction of Hippodamia variegata are increasingly harmed by progressive increases in temperature (from 32 °C to 35 °C and 38 °C). In this study, transcriptome sequencing analysis was performed on H. variegata, after being exposed to different temperatures (from 32 to 38 °C) for 24 h, using high-throughput sequencing technology. We found the largest number of differentially expressed genes (DEGs) in the 35 °C vs. 32 °C group (1151) followed by the 38 °C vs. 32 °C group (1054) and then the 38 °C vs. 35 °C group (901), indicating that H. variegata expressed the largest number of newly mobilized genes under medium-high temperature (35 °C). Gene functional analysis showed that a large number of DEGs were involved in “Catalytic activity”, “Oxidoreductase activity”, “Metabolic pathways”, and “Longevity regulating pathway-multiple species” gene groups. We randomly selected nine DEGs for validation using qRT-PCR. The results of qRT-PCR were consistent with the transcriptome data, confirming their reliability. Finally, the RNAi results showed that adult survival, longevity, and fecundity were lower in the group in which gene expression of the heat shock proteins (Hsp70-01 and Hsp68) was suppressed than in the control group (injection ds-GFP) at all the experimental temperatures (32, 35, and 38 °C). Our results indicate the important role of the heat shock proteins (Hsp70-01 and Hsp68) in resistance to high-temperature stress in H. variegata and provide a molecular basis for analyzing its thermotolerance mechanism.

Influence of Conditions for Obtaining Polylactide-Based Materials on Their Physico-Mechanical and Rheological Characteristics

The work is devoted to the study of the influence of the conditions for obtaining materials based on the synthetic polymer polylactide on their physico-mechanical and rheological characteristics. These materials are promising for the creation of biodegradable polymer implants of temporary action to maintain the mechanical properties of broken bones during the healing period. They are designed to replace the titanium fixators currently used for these purposes, which is due not only to the need for repeated surgery to extract them, but also to the fact that the strength and modulus of elasticity of titanium fixators exceed the values of bone strength indicators by an order of magnitude, which can cause the phenomenon of bone resorption and a decrease in its strength. It has been established that with an increase in temperature in the plasticization and pressing zone, as well as with an increase in pressure in the press, there is a natural decrease in the viscosity of the polylactide melt, as well as the values of the elastic modulus and breaking stress of solid samples. Varying the cooling rate of the material during the pressing process affects the degree of its crystallinity. At the same time, the lower the cooling rate, the greater the degree of crystallinity of the polylactide and the greater the values of the elastic modulus and breaking stress.

Optimization of ethylene and propylene yields from n-hexane catalytic cracking over H-ZSM-5 catalyst using model based design of experiments (DOE)

Catalytic cracking of n-paraffins of varied carbon chain length (C6-C11) to represent light naphtha and gasoline was studied using extrudates of H-ZSM-5 (zeolite: binder = 70: 30) as a catalyst in a fixed bed reactor. Optimization of ethylene and propylene yields using model-based design of experiments (DOE) was carried out for n-hexane cracking by varying the temperature (550–650℃), weight hourly space velocity (3.3–9.9 h−1) and carrier gas (N2) flowrates (3–10 L/h). These variables showed significant effect on the conversion of n-hexane and yield of ethylene and propylene under studied reaction conditions. The Box-Behnken design coupled with response surface methodology was used to determine the effect of reaction temperature, WHSV and N2 flow rate on the yield of ethylene and propylene. Empirical models were constructed for the response variables namely n-hexane conversion, ethylene (E) yield, propylene (P) yield and total ethylene and propylene (E+P) yield. Main effect plot showed that the average yield of ethylene and propylene increased with increase in reaction temperature and decreased with increase in WHSV. The optimization study of multiple responses showed maximum 94.7% conversion of n-hexane and 46.1 wt% yield of ethylene and propylene at 650℃ catalyst bed temperature, 3.3 h−1 WHSV and 8.3 L/h N2 flow rate. The model predicted ethylene and propylene yields matched closely with experimental data for catalytic cracking of naphtha feed at 550 and 650℃ cracking temperature.

Temperature dependence of leaf breakdown in streams differs between organismal groups and leaf species.

Increased temperatures are altering rates of organic matter (OM) breakdown in stream ecosystems with implications for carbon (C) cycling in the face of global change. The metabolic theory of ecology (MTE) provides a framework for predicting temperature effects on OM breakdown, but differences in the temperature dependence of breakdown driven by different organismal groups (i.e., microorganisms vs. invertebrate detritivores) and litter species remain unresolved. Over two years, we conducted 12 60-day leaf litterbag incubations in 20 headwater streams in the southern Appalachian Mountains (USA). We compared temperature dependence (as activation energy, Ea) between microbial and detritivore-mediated breakdown, and between a highly recalcitrant (Rhododendron maximum) and a relatively labile (Acer rubrum) leaf species. Detritivore-mediated breakdown had a higher Ea than microbial breakdown for both leaf species (Rhododendron: 1.48 > 0.56 eV; Acer: 0.97 > 0.29 eV), and Rhododendron breakdown had a higher Ea than Acer breakdown for both organismal groups. Similarly, the Ea of total (coarse-mesh) Rhododendron breakdown was higher than the Ea of total Acer breakdown (0.89 > 0.52 eV). These effects for total breakdown were large, implying that the number of days to 95% mass loss would decline by 40% for Rhododendron and 26% for Acer between 12°C (our mean temperature value) and 16°C (+4°C, reflecting projected increases in global surface temperature due to climate change). Despite patterns in Ea, overall breakdown rates were higher for microbes than detritivores, and for Acer than Rhododendron over most of our temperature gradient. Additionally, the Ea for a subset of the microbial breakdown data declined from 0.40 to 0.22 eV when fungal biomass was included as a model predictor, highlighting the key role of fungi in determining the temperature dependence of litter breakdown. Our results imply that, as streams warm, routing of leaf litter C to detritivore-mediated fates will increase faster than predicted by previous studies and MTE, especially for labile litter. As temperatures rise, earlier depletion of autumn-shed, labile leaf litter combined with rapid breakdown rates of recalcitrant litter could exacerbate seasonal resource limitation and alter carbon storage and transport dynamics in temperate headwater stream networks.

The effect of differing Y concentrations on the evolution of the structure and mechanical properties of FeCrAl alloy

The influence of different Y concentrations on the evolution of the structural and mechanical properties of FeCrAl alloys is investigated in this work. The ingot casting process was used to produce alloys with Y mass fractions of 0%, 0.03%, and 0.25%, respectively. They were then annealed for 15 min at 850°C, 950°C, and 1050°C before being quenched by water to room temperature. Microstructure and mechanical properties were analyzed using OM, EPMA, EBSD, and tensile tests. The addition of 0.03% Y to FeCrAl alloy and annealing at 850°C resulted in the greatest overall performance of the alloy. This had a tensile strength of 635.62 MPa, yield strength of 465.48 MPa, and elongation of 27.04%. With an increase in Y concentration or annealing temperature, the tensile, yield, and elongation properties decrease. This phenomenon can be attributed to the incorporation of Y, which creates a fine Y-rich second phase in the alloy. These phases act as heterogeneous nuclei, pinning the grains during solidification, effectively reducing grain growth and refining the grains. Grain refinement and an increase in the number of grain boundaries hinder dislocation movement, thereby enhancing the alloy's tensile and yield strength. Simultaneously, this prevents the disappearance of α-fiber textures and the creation of γ-fiber textures during recrystallization and reduces the strength of the γ-fiber textures in the alloy microstructure. However, as the annealing temperature increases, microstructure grain growth and the number of grain boundaries decrease. Moreover, higher Y concentrations result in the formation of large, striated Fe-Y phases, which impair the forming properties of the alloy and consequently reduce its tensile properties. Therefore, future research should focus on effectively avoiding the formation of coarse second phases in the microstructure of FeCrAl alloy to enhance its overall performance.

A comprehensive study on the effects of annular protrusion for cavitation intensification in Venturi tubes

Hydrodynamic cavitation, a novel advanced oxidation technique that is notable for its high performance on energy efficiency and environmentally friendly, has incited broad interest. Enhancement of cavitation forms an emerging field in this context. A semi-circular annular protrusion has been introduced into Venturi tubes for cavitation intensification. Initially, improved multiphase flow-cavitation chemical effect simulations are constructed, enabling accurate estimations of the cavitation process on multiscale. Based on this model, an in-depth analysis is carried out to reveal the influential mechanisms of protrusion. Subsequently, optimization of protrusion structure is conducted through a comprehensive analysis of cavitation flow characteristics. The interaction between pressure and protrusion structure are further explored utilizing multi-factor optimization methods. Results indicate a significant performance improvement on the cavitating Venturi tube with a semi-circular annular protrusion. This is attributed to an extended low-pressure area, prolonged high-speed duration, and the increase in both collapse pressure and temperature, yielding higher amounts of free radicals. The semi-circular protrusion is superior to the triangle and rectangle shape. Its position and height significantly impact cavitation intensity in accordance with the generated cavitation patterns, pressure distribution, velocity magnitude and streamlines. Interactive factors analysis reveals strong linear relationships between optimal protrusion height, position and inlet pressure (R2 = 0.999 and 0.992). In comparison to smooth Venturi tubes, recommended designs have shown the vapor volume fraction enhanced by 212 %, 230 %, 255 %, and 117 % at 3, 4, 5, and 6 bar. Accordingly, the ˑOH prediction multiplies to 23 times, 33 times, 107 times and 3 times. This study provides theoretical backing for engineering applications of the semi-circular annular protrusion in Venturi tubes and contributes towards improved cavitation efficiency and reduced experimental and time costs.

Comparative investigation of heat extraction performance in 3D self-affine rough single fractures using CO2,N2O and H2O as heat transfer fluid

The type and thermophysical properties of heat transfer fluids significantly impact the heat extraction rate of Enhanced Geothermal Systems (EGS). Studies based on field-scale stochastic discrete fracture network geometric models have certain limitations and uncertainties. To compare the heat extraction performance of heat transfer fluids H2O, CO2, and N2O in a core-scale (φ50 × 100 mm) rough single fracture in hot dry rock, we first constructed the fracture geometry with rock surface roughness characteristics using a fractal self-affine function, with a joint roughness coefficient (JRC) of 12.38. Then, at temperatures ranging from 37 to 300°C and a pressure of 30 MPa, we established a thermo-hydraulic (TH) coupling model based on the thermophysical parameter equations of the three heat transfer fluids. Finally, we conducted a comparative study of the changes in the outlet mean temperature and heat extraction rate after flowing through the fracture, as well as the temperature distribution on the fracture surface, under conditions of constant inlet flow velocity with varying inlet temperature and constant inlet temperature with varying inlet flow velocity. The results indicate that (1) with the increase in inlet flow velocity and temperature, the outlet mean temperature and heat extraction rate of CO2 and N2O at the fracture outlet are essentially the same and lower than those of H2O. (2) When the inlet flow velocity increases from 0.005 m/s to 0.025 m/s, the thermal convection effect from the rock matrix to the fluid in the fracture predominates, and flow velocity is the main factor affecting the heat transfer process between the fluid and the rock matrix. When the inlet temperature increases from 37°C to 57°C, the thermal conduction effect from the rock matrix to the fluid in the fracture predominates, and temperature is the main factor affecting the heat transfer process between the fluid and the rock matrix.(3)When maintaining constant inlet temperature, increasing inlet flow velocity from 0.005 m/s to 0.025 m/s results in CO2 experiencing a maximum heat extraction rate increase of 118.85 W. In contrast, N2O experiences 117.05 W, and H2O experiences 266.4 W.(4) When the inlet flow rate is constant, the maximum increase in heat extraction rate for CO2 is 15.34 W as the inlet temperature increases from 37 °C to 57 °C; for N2O, it is 13.9 W; and for H2O, it is 45.45 W.

Tailoring Pd/M@CoAlO core-shell catalyst morphology for efficient methane oxidation

The control of low-concentration methane (CH4) emissions is a critical component of the ‘dual carbon’ strategy, and catalytic combustion technology focused on catalyst design is recognized as a promising avenue for achieving it. However, the zeolite-based catalysts are highly prone to deactivation under hydrothermal environments, thus limiting their practical applicability. Herein, we have utilized layered double hydroxides (LDHs) as precursors and integrated them with Pd/M through a co-precipitation method to fabricate Pd/M@CoAlO composite catalysts with a core–shell structure, focused on the impact of CoAlO morphology on the activity and stability for CH4 oxidation. It revealed that the incorporation of CoAlO significantly enhanced the catalytic combustion efficiency and the hydrothermal stability of Pd/M. Furthermore, an increase in the calcination temperature led to a progressive degradation of the sheet-like or petal-shaped structure of CoAlO within the Pd/M@CoAlO composite catalysts. This structural collapse eventually resulted in the formation of CoAlO dense particles that enveloped the Pd/M, adversely affecting the adsorption of oxygen and the exposure of active sites. This work underscores the importance of morphological control, providing significant guidance for the strategic design and development of catalysts tailored for CH4 catalytic combustion.

Heat conduction simulation of chondrocyte-embedded agarose gels suggests negligible impact of viscoelastic dissipation on temperature change

Agarose is commonly used for 3D cell culture and to mimic the stiffness of the pericellular matrix of articular chondrocytes. Although it is known that both temperature and mechanical stimulation affect the metabolism of chondrocytes, little is known about the thermal properties of agarose hydrogels. Thermal properties of agarose are needed to analyze potential heat production by chondrocytes induced by various experimental stimuli (carbon source, cyclical compression, etc). Utilizing ASTM C177, a custom-built thermal conductivity measuring device was constructed and used to calculate the thermal conductivity of 4.5 % low gelling temperature agarose hydrogels. Additionally, Differential Scanning Calorimetry was used to calculate the specific heat capacity of the agarose hydrogels. Testing of chondrocyte-embedded agarose hydrogels commonly occurs in Phosphate-Buffered Saline (PBS), and thermal analysis requires the free convection coefficient of PBS. This was calculated using a 2D heat conduction simulation within MATLAB in tandem with experimental data collected for known boundary and initial conditions. The specific heat capacity and thermal conductivity of 4.5 % agarose hydrogels was calculated to be 2.85 J/g°C and 0.121 W/mK, respectively. The free convection coefficient of PBS was calculated to be 1000.1 W/m2K. The values of specific heat capacity and thermal conductivity for agarose are similar to the reported values for articular cartilage, which are 3.20 J/g°C and 0.21 W/mK (Moghadam, et al. 2014). These data show that cyclical loading of hydrogel samples with these thermal properties will result in negligible temperature increases. This suggests that in addition to 4.5 % agarose hydrogels mimicking the physiological stiffness of the cartilage PCM, they can also mimic the thermal properties of articular cartilage for in vitro studies.

Molecular simulation of CO2/N2 injection on CH4 adsorption and diffusion

As an efficient and clean energy, coalbed methane development and utilization have deep significance in promoting energy conservation and emission reduction, reducing greenhouse gas emissions. Therefore, molecular simulation was utilized to study the influence of N2/CO2 on the adsorption and diffusion of methane in coal under different gas injection methods and to elucidate the influence of varying gas injection methods on the efficiency of coalbed methane extraction, which provides a basis for the efficient development of coalbed methane. The results show that the adsorption effect of gases in coal decreases with the increase of temperature and increases with the rise of pressure, and the adsorption performance of the three gases in coal shows the law of CO2 > CH4 > N2. In addition, the injection of CO2/N2 had an obvious inhibition effect on CH4 adsorption, and the inhibition effect of CO2 was more significant, and the inhibition effect on CH4 adsorption reached the maximum when the two gases were mixture injected. In terms of diffusion, compared with separate injection, mixed injection of N2 + CO2 promotes CH4 diffusion more effectively, which can be reflected in the relative concentration distribution and velocity distribution. The injection of N2 helps to increase the porosity of coal, and the injection of CO2 and N2 + CO2 will lead to the decrease of porosity, but the mixed gas injection has less effect than the injection of CO2 alone.

Laser-Assisted Photo-Thermal Reaction for Ultrafast Synthesis of Single-Walled Carbon Nanotube/Copper Nanoparticles Hybrid Films as Flexible Electrodes.

The hybridization of single-walled carbon nanotubes (SWCNTs) and Cu nanoparticles offers a promising strategy for creating highly conductive and mechanically stable fillers for flexible printed electronics. In this study, we report the ultrafast synthesis of SWCNT/Cu hybrid nanostructures and the fabrication of flexible electrodes under ambient conditions through a laser-induced photo-thermal reaction. Thermal energy generated from the nonradiative relaxation of the π-plasmon resonance of SWCNTs was utilized to reduce the Cu-complex (known as a metal-organic decomposition ink) into Cu nanoparticles. We systematically investigated the effects of SWCNT concentration and output laser power on the structural and electrical properties of the SWCNT/Cu hybrid electrodes. The SWCNT/Cu electrodes achieved a minimum electrical resistivity of 46 μohm·cm, comparable to that of the metal-based printed electrodes. Mechanical bending tests demonstrated that the SWCNT/Cu electrodes were highly stable and durable, with no significant deformation observed even after 1000 bending cycles. Additionally, the electrodes showed rapid temperature increases and stable Joule heating performance, reaching temperatures of nearly 80 °C at an applied voltage of less than 3.5 V.

A Comprehensive Review of Potential Adaptation and Mitigation Strategies in Agriculture in the Current Climate Change Scenarios

Climate change has a major impact on agriculture worldwide, but in certain regions, like India, this impact is more pronounced than in others. India's large population, heavy reliance on natural resources, and lack of coping mechanisms make it difficult for the country to adapt to the changing climate. India has experienced a notable warming trend over the past century, with an approximate 0.60 °C increase in temperature. This trend is anticipated to continue, possibly having catastrophic consequences for agricultural productivity and food security. Climate change is predicted to result in increasingly variable growing conditions for many crops, making it more challenging for farmers to schedule the planting and harvesting of their crops. Rapid reaction times and coordination are required to mitigate the consequences of climate change on Indian agriculture. This means implementing adaptation tactics, such as cultivating crop varieties that can tolerate high temperatures, promoting water-efficient irrigation techniques, preserving soil health, and enhancing climate resilience through integrated farming systems. India can lessen the negative effects of climate change on its agriculture sector and guarantee food security for its growing population by taking proactive steps and implementing sustainable farming practices.

Spotting ignition of plastic foam by a fast-moving hot metal particle

Spotting ignition involves dynamic interaction between fuel bed and hot particles, but the scientific understanding of the ignition by a fast-moving hot particle is still limited. Herein, a hot steel particle with various horizontal velocities, temperatures, and sizes is shot to ignite vertically oriented low-density expandable polystyrene foam. A high-speed particle can directly get embedded into the foam to achieve flash-point, fire-point, or no ignition, while a low-speed particle bounces away from the foam without ignition. Results show that for a particle of 1150 °C, its minimum velocity for embedding is 12.00 m/s. Such a critical velocity for hot-particle embedded or ignition slightly decreases as particle temperature increases. Minimum ignition temperature of these high-speed particles is 200 °C higher than that of near-static or with a low free-fall velocity, due to the shorter residence time and insufficient to produce a flammable mixture. Moreover, when the particle is neither too slow to bounce away nor too fast to get embedded, it will be partially embedded on the sample surface to burnout the fuel, posing the biggest fire hazard. It deepens our knowledge of the complex interaction between hot moving particles and insulation foam to reduce spotting fire risk for building façade.

Regulation of microstructure, phase transformation behavior, and enhanced high superelastic cycling stability in laser direct energy deposition NiTi shape memory alloys via aging treatment

The remarkable mechanical properties, fatigue resistance, wear and corrosion resistance, biocompatibility, shape memory effect, and superelasticity of NiTi shape memory alloys make them applied in diverse engineering areas, including satellite antennas, oil pipelines, and vascular stents. This paper focuses on the preparation of Ni50.8Ti49.2 alloy via laser directed energy deposition (LDED) utilizing pre-alloyed powder and the heat treatment of solid solution at 950 °C for 8 h followed by subsequent aging at 350 °C, 450 °C and 550 °C for 2 h. The influence of varying aging temperature on the microstructures, phase transformation behavior and superelastic cyclic stability of them was comprehensively summarized and discussed. The martensitic transformation temperatures of NiTi alloys after aging decrease as the aging temperature increases. Specifically, NiTi alloys aged at 450 °C for 2 h exhibit excellent superelasticity and high cyclic stability. After an initial loading-unloading cycle with an 8.079 % pre-strain, the alloy achieves 100 % complete recovery. Even after 10 cycles, the recoverable strain remains at approximately 7.374 %, with a recovery rate exceeding 90 %. These outstanding properties of high superelasticity and superior cyclic stability are significantly better than most other LDED NiTi alloys. This exceptional performance is primarily attributed to the synergistic effects of the R-phase and Ti3Ni4 precipitates on the shape memory alloy.