Effect Of Temperature Gradient Research Articles

Impact of Pressure and Temperature on Charge Accumulation Characteristics of Insulators in Direct-Current Gas-Insulated Switchgear

Direct-current gas-insulated switchgear (DC GIS) is an important device for promoting the lightweight and compact design of offshore wind power platforms. Gas pressure and temperature gradients are crucial factors that must be considered during the design process of the DC GIS. In this study, the multi-physics coupling model of basin insulators considering surface charge accumulation was established, and the corresponding real-sized insulator surface charge measurement platform was constructed. The effects of gas pressure and temperature gradient on the surface charge accumulation characteristics were investigated, respectively. The results show that the effect of gas pressure on the surface charge distribution characteristics depends on the dominant mode of surface charge. When volume conduction is dominant, the effect of gas pressure on the surface charge is negligible. However, when gas conduction is dominant, the accumulation of a uniform charge pattern on the insulator surface increases with the rise in gas pressure. Furthermore, due to gas convection, the temperature of the upper part of the DC GIS is significantly higher than that of the lower part, which leads to a temperature difference between the upper and lower surfaces of the insulator. The charge density on the insulator upper surface near the central conductor rises with the increase in load current.

Effect of aging level on the healing properties of an induction-heated ultra-thin wearing course and its mechanism

Electromagnetic induction heating can accelerate crack self-healing in asphalt concrete and extend its service life. In the maintenance project of existing pavements, induction heating and ultra-thin wearing course can be combined by paving functional induction heating wearing course. However, the ultra-thin wearing course is directly affected by the environment and loading, and undergoes aging in the service process. Thermo-oxidative aging is an irreversible and important mechanism that seriously affect the rheological and healing properties of asphalt. Therefore, the purpose of this work is to examine the impact of thermo-oxidative aging on the induction heating-healing of an ultra-thin wearing course mixture. Firstly, the AC-5 induction heated ultra-thin wearing course (IHUC) containing 1 % steel wool fiber by aggregate mass was prepared. Subsequently, the IHUC was aged to six different levels. Then, the induction heating and healing properties of the aged IHUC were evaluated. Simultaneously, the aged asphalt binder was extracted and its rheological characteristics and chemical alterations were studied. The outcomes showed that the heating rate of IHUC decreased, but the temperature gradient effect reduced at higher aging level. The optimal healing temperature of IHUC shifted to a higher temperature region and the healing rate decreased. Both heating cycles and thermo-oxidative aging reduce healing effectiveness, but the impact of heating cycles is less compared to aging. Rheology and chemical structure test results of extracted asphalt binder showed that the transformation of the molecular structure caused the fluidity and self-healing properties of asphalt were decreased. This ultimately decreased the healing rate of IHUC.

Reduced Order Electrochemical-Thermal Modeling of Cylindrical Cells Containing Graphite-Silicon Anodes Considering Thermal Gradients and Hysteresis

Electrochemical thermal modeling of cylindrical cells presents unique challenges compared to other cell formats due to the effect of internal temperature gradients, which typically requires time-consuming simulations due to the number of mesh elements solved numerically. Adding to the difficulty, the emergence of silicon anodes induces voltage hysteresis that affects the cell behavior. In this paper, a reduced-order electrochemical-thermal model is developed for a 21700 cell, which is highlighted by three microcells considering the effects of internal temperature gradients, and an anodic stress model capturing the hysteresis effects caused by the silicon content. The electrochemical, thermal, and mechanical behaviors are investigated. During operations, a temperature gradient arises in the radial direction, resulting in a decrease in local resistance and an increase in reaction rate at the high-temperature core location. The presence of silicon causes a voltage hysteresis that is dominant in the low SOC range, which affects not only the irreversible but also the entropic heat generation. The proposed method achieves an 85% calculation time reduction compared with the existing literature method and a 95% reduction compared with the full order method, while maintaining the accuracy of the terminal voltage and heat generation rate predictions that are validated by experiments.

Simplified structural analysis of laminated glass panels during fire exposure

Due to their high aesthetic value, energy-efficient properties, and contribution to daylighting, the demand for using glass panels in modern buildings has considerably increased over the past decades. However, ordinary glass panels are highly susceptible to cracking during a fire because of the temperature difference between the part of the glass exposed to the fire and the part protected by the frame. Damage to the glass can allow additional oxygen intake, leading to the flashover phenomenon significantly increasing fire severity. Laminated glass is superior to ordinary glass in its impact resistance, sound insulation, and ability to maintain post-breakage integrity. This paper provides a simplified method to study the effect of temperature gradients on the cracking behaviour of laminated glass panels. The temperature of the unprotected portion of the glass panel is first estimated by evaluating the mid-thickness temperature using the general heat transfer equation. Then, equations developed based on a parametric study that utilized ABAQUS are proposed to estimate the exposed and unexposed surface temperatures. This step was followed by evaluating the temperature of the protected glass portion. Subsequently, a method based on strain-equilibrium principles was developed to predict the corresponding maximum thermal stress. Comparisons with experimental and numerical work by others validated the proposed method.

Experimental study on the water and heat dynamic characteristics of silty clay at different depths under temperature gradient

Soil properties play a crucial role in the stability of engineering foundations, particularly in cold regions where temperature gradients impact water migration and soil conditions. This study utilized MRI-Cryogenic Soil-Moisture Analyzer (MRI-CSMA) to conduct indoor freeze-thaw experiments on silty clay specimens with varying initial water contents (12.0 %, 16.8 %, and 21.1 %). Dynamic changes in water content and temperature at different soil depths were analyzed. The results revealed distinct stage decrease characteristics in both temperature and water content as freezing progressed, with more pronounced changes closer to the cold end. Conversely, during thawing, temperatures and water content gradually increased as the boundary temperature rose. Notably, after the freeze-thaw cycle, the frozen zone consistently retained higher water content than the unfrozen zone, indicating water redistribution, regardless of initial water content levels. Furthermore, in three soil samples with different initial water contents, the water migration flux in the unfrozen soil layer decreased exponentially as freezing time increased. This phenomenon can be attributed to the combined effects of water boundary conditions, temperature gradients, and soil structure changes during soil freezing. These findings are likely to have significant implications for understanding water-heat dynamics in cold region soils as well as ensuring the stability of engineering projects.

Nitrate denitrification rate response to temperature gradient change during river bank infiltration.

Nitrate attenuation during river bank infiltration is the key process for reducing nitrogen pollution. Temperature is considered to be an important factor affecting nitrate attenuation. However, the magnitude and mechanism of its impact have not been clear for a long time. In this study, the effects of temperature and temperature gradient on the nitrate denitrification rate were investigated via static batch and dynamic soil column simulation experiments. The results showed that temperature had a significant effect on the denitrification rate. Temperature effects were first observed in denitrifying bacteria. At low temperatures, the microorganism diversity was low, resulting in a lower denitrification rate constant. The static experimental results showed that the denitrification rate at 19°C was approximately 2.4 times that at 10°C. The dynamic soil column experiment established an exponential positive correlation between the nitrate denitrification decay kinetic constant and temperature. The affinity of denitrifying enzymes for nitrate in the reaction substrate was ordered as follows: decreasing temperature gradient (30°C → 10°C) > zero temperature gradient (10°C) > increasing temperature gradient condition (0°C → 10°C). This study provides a theoretical basis for the biogeochemical processes underlying river bank infiltration, which will help aid in the development and utilization of groundwater resources.

Effects of planetary day-night temperature gradients on He 1083 nm transit spectra

A notable fraction of helium observations probing the evaporating atmospheres of short-period gas giants at 1083 nm exhibit a blueshift during transit, which might be indicative of a day-to-night side flow. In this study, we explore the gas dynamic effects of day-to-night temperature contrasts on the escaping atmosphere of a tidally locked planet. Using a combination of 3D hydrodynamic simulations and radiative transfer post-processing, we modeled the transmission spectra of the metastable helium triplet. Our key findings are as follows: (1) Increasing the day-night anisotropy leads to a narrowing of the helium line and an increase in the blueshift of the line centroid of a few km s−1. (2) The velocity shift of the line depends on the line-forming altitude, with higher planetary mass-loss rates causing the line to form at higher altitudes, resulting in a more pronounced velocity shift. (3) A critical point of day-night anisotropy comes about when the blueshift saturates, due to turbulent flows generated by outflow material falling back onto the planet’s night side. (4) A strong stellar wind and the presence of turbulent flows may induce time variations in the velocity shift. Assuming that the day-night temperature gradient is the main cause of the observed blueshifts in the He-1083 nm triplet, the correlation between the velocity shift and day-night anisotropy provides an opportunity to constrain the temperature gradient of the line-forming region.

Effects of temperature gradients on thermomechanical fatigue of nickel-based superalloy

Temperature-gradient-mechanical fatigue (TGMF) is a significant concern in internal cooling turbine blades. In the present study, the through-thickness temperature gradient was determined by the inverse heat conduction method and investigated in TGMF. Using the continuum damage mechanics, the environmental impact was identified as the primary contributor to the in-phase TGMF damage. A damage accumulation model encompassing fatigue, creep and environmental impact was established and provided satisfactory accuracy in TGMF life assessments. The main conclusion is that temperature gradients do not change the fracture mode but significantly increase stress levels by at least 20%, accelerating oxidation damage and resulting in a TGMF life ca. 10 times shorter than that of TMF.

Heat of transport for hydrogen and hydrides in Zircaloy

ABSTRACT Hydrogen diffuses in zirconium alloys in response to gradients in hydrogen concentration, temperature, and stress. This essay discusses the results of several evaluations of the coefficient describing the effects of temperature gradients called the heat of transport. The values distinguish between when hydrogen is in solution, (25 ± 3) kJ/mol, and when stable hydrides are present, (116 ± 17) kJ/mol.

Modeling of rapid solidification in Laser Powder Bed Fusion processes

This paper addresses a numerical framework for modeling site-specific microstructure evolution in Laser Powder Bed Fusion (LPBF), where rapid solidification significantly influences the microstructure and properties of manufactured components. The fine microstructure and rapid solidification can enhance mechanical properties in final parts, yet pose challenges in controlling microstructure and addressing potential defects. In this study, an in-house developed free surface thermo-fluidic Computational Fluid Dynamics (CFD) model is coupled with a binary alloy phase-field model characterized by rapid solidification kinetics. The CFD model considers complex fluid flows related to Marangoni and recoil pressure, laser-material interactions, and rapid melting and solidification of the melt pool. A convergence study for the phase-field model is conducted, comparing simulated partition coefficients with the Continuous Growth Model (CGM) theory. The study investigates the individual effects of temperature gradients and solidification rates on simulated microstructure. Results indicate that, for the same order of magnitude change, the solidification rate has a more pronounced effect on microstructure than temperature gradients. The paper concludes with the simulation of site-specific microstructure evolution within the melt pool, comparing the results with experiments conducted at varied scanning speeds. The predicted microstructure aligns well with experimental measurements, suggesting the potential utility of the developed phase-field model in quantitative microstructural modeling. Overall, this work contributes to understanding microstructure evolution under rapid solidification conditions, providing a fundamental basis for optimizing the LPBF process.

Graphite sheet assisted photovoltaic -thermoelectric generator for hydrogen generation from seawater

ABSTRACT Different intermediate steps exist between solar energy as input and hydrogen as output. Most of the findings in this domain revolved around water electrolysis as an intermediate step to produce hydrogen. Therefore, the discussion in the work is intended to discuss water-splitting-based hydrogen production through electrolysis. The electrolysis process requires continuous electrical input. Installed solar PV is inevitably supposed to be under prolonged solar irradiance. The prolonged solar incidence causes the panel to get heated, leading to lower overall performance. Thermoelectric Generators (TEGs) convert the waste heat into additional electrical energy apart from the panel. In the experimentation of the work, the effect of temperature gradient is explored. During the implementation of PV-TEG, TEG electrical output can be improved with the help of auxiliary heat dissipators. This study includes graphite as a heat dissipator and a Hofmann voltameter for hydrogen production. Under 800 W/m2 of solar irradiation, the maximum hydrogen yield is obtained when PV-TEG (with graphite sheet) is connected to the Hofmann voltameter. The yield ranges from 0.132 bar/sec to 0.137 bar/sec.

Effect of Temperature Gradient on Compressive Strength and Strain Characteristics of Coarse-Grained Frozen Soil

Effect of Temperature Gradient on Compressive Strength and Strain Characteristics of Coarse-Grained Frozen Soil

Outlet boundary condition and mean temperature gradient effects on the minimum acoustics disturbances energy in triggering nonlinear thermoacoustic instability

In this study, we theoretically investigate the impact of outlet boundary conditions and mean temperature gradients on the maximum transient growth rate of acoustical energy and the critical energy required for triggering. Our analysis encompasses open–open and open–closed thermoacoustic systems. The theoretical models developed focus on horizontal ducts with a mean temperature jump over the heat source, employing the modified King's law. By linearizing the unsteady heat release, the nonlinear thermoacoustic equations transform into linearized-delay ones. This approach enables us to predict optimal initial perturbations for linearized-delay and nonlinear systems, corresponding to maximum transient growth rates of acoustic energy over short and long periods, respectively, thus providing insights into critical energy for triggering. We find that a closed outlet leads to higher transient energy growth and a lower critical energy for triggering compared to an open outlet. The increased mean temperature gradient has a “destructive” impact on triggering in open–open systems but a “constructive” effect in open–closed systems. Raising the mean temperature ratio generally increases the critical energy for triggering in the open–open system, whereas it decreases the critical energy in the open–closed system. The critical energy for nonlinear optimal initial perturbations is notably affected by the minimum energy of critical unstable periodic solutions, while the critical energy for linearized-delay optimal initial perturbations is closely tied to the energy level of stable periodic solutions. Due to the transient energy growth rate, the critical energy for nonlinear optimal initial perturbations is significantly lower than that for linearized-delay optimal initial perturbations.

Radon indoors source potential from soil gas in a temperate climate: impact of infiltration rate and seismicity

Indoor radon source potential from unground soil was monitored using prototype devices approaching a dwelling with a cellar basement at 1 depth from the soil-atmosphere interface. Therefore, the radon concentrations in soil gas were monitored at 1 m depth. Integrated radon measurements were performed, and the results correlated with meteorological parameters. The influence of the difference in outdoor and device-soil temperature was considered, and the infiltration rate was calculated. The effect of the soil temperature gradient on the soil radon entry rate was evaluated. The indoor radon entry rate due to the soil gas was 7.0 ± 2.7 Bq m−3 h−1. The radon entry rate was 5.0 ± 0.8 Bq m−3 h−1 due to diffusion. In contrast, the advection-drive flow of soil gas is ranged up to ± 4.0 Bq m−3 h−1. So, the infiltration rate of the model dwelling was 0.7 (± 0.5) × 10−1 h−1 if only the stack effect occurred. The radon levels in tap water were measured, and the radon entry rate was estimated at 1.3 ± 0.7 Bq m−3 h−1. If the ventilation rate is low or seismic faulting appears, the soil radon entry is increased by one order of magnitude. The soil radon appeared like the building materials, having 1/3 of the total indoor radon entry, while outdoor air was slightly lower (28%), with tap water at 5%. The resident’s mortality risk occurred at < 2.5% for typical dwellings in temperate climate areas founded on sand-gravel underground. The risk rises to 34% with an extremely low ventilation rate between indoors and outdoors or high radon entry from the soil due to seismic faulting.

Multi-scale gyrokinetic simulations of JT-60U L-mode plasma: reduction of the ion scale energy loss due to the nonlinear coupling with the electron scale turbulence

We investigate the effect of the electron temperature gradient (ETG) driven turbulence on the energy transport in JT-60U L-mode plasma by means of the multi-scale gyrokinetic simulation. In the core region at r/a=0.5 , the instability in the ion scale is driven by the ion temperature gradient (ITG), meanwhile strong unstable ETG modes are found in the electron scale. The nonlinear multi-scale gyrokinetic simulation shows that ETG modes are stabilized in the nonlinear phase and the energy transport in the multi-scale simulation is similar to that obtained in the ion scale ITG simulation. In an outer region at r/a=0.6 , the ion scale instability changes to be the trapped electron mode (TEM). The multi-scale simulation shows that both the ion and the electron energy flux are reduced by ∼30% compared to those obtained in the single scale TEM simulation. Interestingly, the electron energy flux is close to the experimental value after this reduction. From the data analyses, we find that ETG turbulence damps the energy of TEM modes through the ion scale/electron scale coupling and the electron scale/electron scale coupling, and can be modeled as a turbulent diffusion of TEM modes. These results suggest that the single ion scale simulation seems to be still valid in the inner region with r/a<0.5 . However, in the outer region it is necessary to include the ETG modes in the gyrokinetic simulations to explain the energy transport in this L-mode plasma. This is the first result showing that ETG turbulence can reduce the electron energy loss via the cross-scale interaction in a real tokamak equilibrium profile.

Numerical simulation of temperature gradient effects on gallium nitride crystal growth by sodium-flux method

During the growth of gallium nitride single crystals by sodium-flux method, temperature significantly impacts crystal quality. In this study, the mechanism of the effect of different temperature gradients on crystal growth is analyzed in depth using a combination of numerical simulation and experiment. The experimental results show that epitaxial growth of crystals occurs under positive temperature gradient conditions, while there is dissolution of seed crystals under negative temperature gradient conditions. The temperature, flow, and concentration data of the melted material during crystal growth were calculated using numerical simulation. The simulation findings reveal that the distribution of solution supersaturation varies according to temperature. High supersaturation at the bottom of the melt is favorable for crystal epitaxial growth on the surface of seed crystals under a positive temperature gradient. Meanwhile, low supersaturation at the top of the melt suppresses the hard polycrystalline layer here. Under negative temperature gradient conditions, low supersaturation at the bottom of the melt may lead to remelting of seed crystals, which is consistent with the experimental phenomenon. Furthermore, we propose an optimized heat source profile. This profile manages high supersaturation near seed crystals, aiding continuous growth. Finally, we have applied the curve in an applied way by proposing a multi-stage heating device, based on which the desired arbitrary temperature profile can be modulated. This research has broad applications in a variety of crystal growth experiments using fluid as the mother phase.

An experimental study on effects of temperature gradient on microstructure of a 308L stainless steel manufactured by directed energy deposition

An experimental study on effects of temperature gradient on microstructure of a 308L stainless steel manufactured by directed energy deposition

Interactive effects of temperature and velocity on the feeding behavior of competing native and invasive stream fishes

The integration of invasive species into native communities may result in the destabilization of food webs through predation of native prey and competition with native predators. These negative effects are likely to be exacerbated by climate change, increasing the frequency of heat waves, droughts, and high-flow events. Invasive Round Goby (Neogobius melanostomus) and native White Sucker (Catostomus commersonii) were collected from the wild and acclimated to a range of temperatures expected to capture increases in temperature under climate change. In the laboratory, we measured the effects of temperature (19, 22, 25, and 28°C) and velocity gradients (0, 0.15, 0.3, 0.6 m/s at 22 and 25°C) on the prey consumption and foraging behavior of each species. We found that the prey consumption and number of attacks (lunges at prey) of both species increased with temperature but were consistently higher in Round Goby. Velocity had an interactive effect with temperature for prey consumption and foraging behavior, where generally, velocity tolerance for both species was higher at 22°C than at 25°C. White Sucker tolerance to velocity was higher than Round Goby, suggesting that systems with higher velocities may provide a competitive advantage in high-flow environments. Our results stress the importance of interactive experiments when examining the impact of invasive species on native competitors under shifting climatic conditions.

Evolution Mechanism of Interlayer Properties of CRTS III Slab Track during Construction

The interlayer properties of the CRTS III slab track during construction directly affect its long-term service condition. This article introduces time-varying coefficients that characterize the early properties of the interface between track slab and SCC to improve the bilinear CZM. Based on this, an interlayer property evolution model of the CRTS III slab track during construction is established. The evolution mechanism of interlayer properties under complex loads and the influence mechanism of key parameters on them are revealed. The results show that after SCC pouring, the interlayer damage at the corner of the slab becomes a sensitive area due to the combined effects of SCC shrinkage and temperature gradients. Interlayer damage initially manifests at the corner of the slab before progressively spreading toward the center of the slab, influencing the composite performance and force transmission characteristics of the track structure. The interlayer bonding property, shrinkage performance of SCC, and construction temperature substantially affect interlayer damage evolution. To reduce the risk of damage, mineral admixtures and expansion agents can be added as additives to improve the bonding property and minimize shrinkage of SCC. Insulation measures should be taken for SCC during low-temperature construction, and SCC pouring construction below 0 °C and above 30 °C should be avoided.

Effect of basic Temperature Gradients on Electrothermal Convection in a Rotating Layer of Viscoelastic (Walter’s B) Fluid Saturated Porous Medium Heated from Below

Combined Effect of Thermal Modulation and Rotation on the Onset of Convection in Walter's B Viscoelastic Fluid Saturated Porous Medium has been investigated. The problem is numerically solved using the Galerkin method after applying linear stability analysis and normal modes. It is possible to derive the dispersion relation while accounting for the effects of wave number, electric Rayleigh number, Darcy number, Taylor number, and thermal electric Rayleigh number. Graphically, the effects of the electric Rayleigh number, Darcy number, Wave number, and Taylor number on the onset of stationary convection have been studied. Under the boundary conditions considered, The kinematic viscoelasticity accounting for rheology of the nanofluid has no effect on the stationary convection for Walters’ (model B’) nanofluids and behaves like an ordinary Newtonian nanofluid.