Temperature Dependence Of Viscosity Research Articles

Viscosity model for the middle fraction of Atasu-Alashankou oil sludge

The temperature dependence of dynamic viscosity was calculated on the basis of a new cluster-association equation, which was derived within the framework of the concept of chaotic particles. It was shown that the degree of cluster association naturally decreases with an increase in temperature, on average corresponding to the arrangement of three to four cluster particles in the association. For the first time, the values of the activation energy per monomer were obtained when assigning the activation energy to the average number of clusters.

Multi-scale investigation of heat and momentum transfer in packed-bed TES systems up to 800 K

With the rising cost of energy and the advancement of corporate social responsibility, there is a growing interest in addressing the challenge of recovering and storing high-temperature waste heat. Sensible heat storage in packed beds stands out as a cost-effective and seemingly straightforward solution for high-temperature Thermal Energy Storage (TES). Engineering models developed to design low-temperature TES systems were tentatively used to design this new generation of high-temperature systems. Delving into the physics of coupled heat and mass transfer reveals a lack of validation of this approach. This study seeks to establish a comprehensive bottom-up methodology - from the particle scale up to the system level - to provide informed and validated engineering models for the design of high-temperature TES systems. To achieve this goal, we developed a multi-scale numerical model to explore the physics of heat and momentum transfer in packed-bed TES systems. At the microscopic scale (pore/particle), we consider the flow of a compressible high-temperature gas between the particles, coupled to transient heat conduction within the particles, with particular attention given to incorporating accurate temperature-dependent viscosity for the gas phase and thermal conductivity and density for both solid and gas phases. At the macroscopic scale (engineering), we propose a high-temperature extension of state-of-the-art two-equation TES models. The governing equations considered are the volume-average conservation laws for gas-mass, gas-momentum and energy of both phases. The multi-scale strategy is applied to a randomly packed bed of spherical particles generated with the discrete element method (DEM) software LIGGGHTS. Numerical models for both scales were implemented in the Porous material Analysis Toolbox based on OpenFoam (PATO), which is made available in Open Source by NASA. Microscopic scale simulations were used to infer the effective parameters needed to inform the macroscopic model, namely, permeability, Forchheimer coefficient, effective thermal conductivities, and the heat transfer coefficient. The informed macroscopic model reproduces with excellent accuracy the average temperature fields of the physics-based microscopic model. Pore-scale analysis shows highly three-dimensional flow characterized by reverse flow and strong cross-flow in the packed bed system. Moreover, it indicates the coupling between temperature and velocity fields, where a nonuniform velocity field results in uneven temperature distributions across the fluid and the solid spheres within the packed bed, subsequently affecting the macroscopic heat transfer coefficient. The overall strategy is validated by comparison to available experimental data. This bottom-up methodology contributes to the understanding and opens new perspectives for a more precise design and monitoring of high-temperature TES systems.

Effects of sugar molecules on the rheological and tribological properties and on the microstructure of agarose-based fluid gels

Introduction: Fluid gels exhibit a unique flow behaviour. Their pronounced viscoelastic behaviour arises from irregular microgel particles, leading to plasticity and yielding, as well as a characteristic transition from a solid to a fluid-like state. This is defined by both the core and the surface structures of the particles. Adding co-solutes such as sucrose alters the network properties at the molecular scale, affecting texture and lubrication. This study investigates how the microscopic changes due to sucrose addition correlate with macroscopic changes.Material and methods: Agarose fluid gels with varying sucrose concentrations were prepared and studied using the rheometer. Temperature dependent viscosity behaviour during gelation under shear was investigated in situ. Light microscopy and particle size measurements were examined, and complemented by amplitude, frequency and flow sweeps as well as tribological studies. These tests allow us to understand the influence of sucrose on the particle network formation.Results and discussion: Sucrose concentration influenced the sizes, shapes, and interconnected network structure of the microgel particles. These microstructural changes are closely related to the dynamic competition between gelation and disruption of the agarose chains during shear, which directly influences the rheological and tribological properties of the resulting fluid gels. Additionally, the association of the agarose chains and their gelation process is also influenced depending on whether the sucrose or agarose was first dissolved in water. The experimental observations suggest specific molecular mechanisms, explaining the role of sucrose in structure formation of agarose-based fluid gels. These results have the potential to expand the applications of fluid gels, which play a crucial role in modifying the texture and flow behaviour of foods and beverages, particularly in addressing challenges such as dysphagia.

Optimal temperatures for measuring oil viscosity to restore its viscosity-temperature dependence according to the Filonov–Reynolds, Walter and Vogel–Fulcher–Tamman formulas

Relevance. Increase in the number of high-viscosity and non-Newtonian oils produced and transported. For such oils, it is important to accurately predict the rheological properties and, in particular, the viscosity-temperature dependence. Viscosity measurement for a wide range of different temperatures is excessively time-consuming and irrational, and in practice, viscosity measurement is used at two or three different temperatures and then conversion formulas are used. It is also important to clarify, which formulas and for which oils should be used to obtain the smallest error. It is important, in particular, to determine the optimal temperatures for measuring the viscosity of oil to restore its viscosity-temperature dependence. Aim. To determine the optimal temperatures for measuring oil viscosity to restore its viscosity-temperature dependence using the Filonov–Reynolds, Walter and Vogel–Fulcher–Tamman formulas, including when calculating for the entire available temperature range. Objects. Viscosity-temperature dependences of oils from the Directory of oils of the USSR. Methods. Processing the viscosity measurement data for 564 oils from the USSR Oil Directory; construction of approximating viscosity-temperature dependencies; determination of error when using the obtained dependencies, including using cross-validation. Results. The authors have calculated the error in application of the Filonov–Reynolds, Walter, Vogel–Fulcher–Tamman formulas, using over 500 oils as an example. It was found that with a random choice of temperatures for measuring viscosity, the minimum average error at another temperature for these formulas is, respectively, 13.8, 10.7 and 6.2%. The use of the Filonov–Reynolds formula is undesirable for calculating viscosity at low temperatures. The Vogel–Fulcher–Tamman formula shows the best results in calculating viscosity when using temperatures of 30–50–70 and 10–30–50°C.

Optimization of the temperature profile of cake batter in an ohmic heating – assisted printing nozzle for 3D food printing applications

Abstract 3D printing of food has great potential for applications such as the design of customised food or the creation of innovative textures. However, printed products often do not retain their structure due to the composition of the material, especially in the case of cereal products. Cooking such products with a nozzle could be an alternative to meet this challenge. The objective of this work was to develop, with the help of a numerical model, a 3D cake batter printing nozzle in which ohmic heating is used for baking. The use of a temperature and shear rate dependent viscosity allowed the solidification of the batter during baking due to starch gelatinization. The numerical model made it possible to predict heterogeneity in temperature distribution. Optimization procedures were used to reach desired temperature profiles at the outlet of the nozzle, reducing by 17 % the electrical power used for heating and by 78 % the energy evacuated during cooling.

Two-phase flow thermo-hydro-mechanical modeling for a water flooding field case

Simulation of subsurface energy system involves multi-physical processes such as thermal, hydraulical, and mechanical (THM) processes, and requires a so-called THM coupled modeling approach. THM coupled modeling is commonly performed in geothermal energy production. However, for hydrocarbon extraction, we need to consider multiphase flow additionally. In this paper, we describe a three-dimensional numerical model of non-isothermal two-phase flow in the deformable porous medium by integrating governing equations of two-phase mixture in the porous media flow in the reservoir. To account for inter-woven impacts in subsurface conditions, we introduced a temperature-dependent fluid viscosity and a fluid density along with a strain-dependent reservoir permeability. Subsequently, we performed numerical experiments of a ten-year water flooding process employing the open-source parallelized code, OpenGeoSys. We considered different well patterns with colder water injection in realistic scenarios. Our results demonstrate that our model can simulate complex interactions of temperature, pore pressure, subsurface stress and water saturation simultaneously to evaluate the recovery performance. High temperature can promote fluid flow while cold water injection under non-isothermal conditions causes the normal stress reduction by significant thermal stress. Under different well patterns the displacement efficiency will be changed by the relative location between injection and production wells. This finding has provided the important reference for fluid flow and induced stress evolution during hydrocarbon exploitation under the environment of large reservoir depth and high temperature.

Bioprinting of human dermal microtissues precursors as building blocks for endogenous in vitro connective tissue manufacturing

The advent of 3D bioprinting technologies in tissue engineering has unlocked the potential to fabricate in vitro tissue models, overcoming the constraints associated with the shape limitations of preformed scaffolds. However, achieving an accurate mimicry of complex tissue microenvironments, encompassing cellular and biochemical components, and orchestrating their supramolecular assembly to form hierarchical structures while maintaining control over tissue formation, is crucial for gaining deeper insights into tissue repair and regeneration. Building upon our expertise in developing competent three-dimensional tissue equivalents (e.g. skin, gut, cervix), we established a two-step bottom-up approach involving the dynamic assembly of microtissue precursors (μTPs) to generate macroscopic functional tissue composed of cell-secreted extracellular matrix (ECM). To enhance precision and scalability, we integrated extrusion-based bioprinting technology into our established paradigm to automate, control and guide the coherent assembly of μTPs into predefined shapes. Compared to cell-aggregated bioink, our μTPs represent a functional unit where cells are embedded in their specific ECM. μTPs were derived from human dermal fibroblasts dynamically seeded onto gelatin-based microbeads. After 9 days, μTPs were suspended (50% v/v) in Pluronic-F127 (30% w/v) (µTP:P30), and the obtained formulation was loaded as bioink into the syringe of the Dr.INVIVO-4D6 extrusion based bioprinter. µTP:P30 bioink showed shear-thinning behavior and temperature-dependent viscosity (gel at T > 30 °C), ensuring µTPs homogenous dispersion within the gel and optimal printability. The bioprinting involved extruding several geometries (line, circle, and square) into Pluronic-F127 (40% w/v) (P40) support bath, leveraging its shear-recovery property. P40 effectively held the bioink throughout and after the bioprinting procedure, until µTPs fused into a continuous connective tissue. µTPs fusion dynamics was studied over 8 days of culture, while the resulting endogenous construct underwent 28 days culture. Histological, immunofluorescence analysis, and second harmonic generation reconstruction revealed an increase in endogenous collagen and fibronectin production within the bioprinted construct, closely resembling the composition of the native connective tissues.

Thermal inspection of hybrid nanofluid flows over a stretched cylinder at an oblique stagnation point with variable characteristics

AbstractThe enhanced thermal characteristics of hybrid nanofluids make them more versatile compared to conventional fluids. These improved thermal properties render hybrid nanomaterials highly practical for a wide range of applications, including solar systems, energy production, and cooling processes. In line with this perspective, the current study concentrates on evaluating the thermal performance of two unique hybrid nanofluid flows that impinge obliquely on a stretched cylinder. Two base fluids, FC‐77 and a binary mixture of water and ethylene glycol (50:50)%, have been considered, with the addition of nanoparticles such as single‐walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWCNTs). The said model's novelty is enhanced by the temperature dependent viscosity and thermal conductivity. Appropriate transformations are applied to derive a system of ordinary differential equations (ODEs), which are then solved numerically using the bvp4c method. A thorough examination is conducted on the physical phenomenon of pertinent parameters, accompanied by graphical representations. The results revealed that, for the FC‐77 coolant‐based hybrid nanofluid, mounting the particle volume fraction leads to a significant reduction in temperature distribution. Additionally, it is perceived that the presence of a variable viscosity parameter causes a reduction in the surface drag coefficient as well as the axial and tangential velocities. The validity of the proposed flow model is demonstrated by comparing the results with those from an earlier study.

Control of temperature dependent viscosity for manufacturing of Bi-doped active fiber

Bi-activated photonic materials are promising for various applications in high-capacity telecommunication, tunable laser, and advanced bioimaging and sensing. Although various Bi-doped material candidates have been explored, manufacturing of Bi heavily doped fiber with excellent optical activity remains a long-standing challenge. Herein, a novel viscosity evolutional behavior mediated strategy for manufacturing of Bi-doped active fiber with high dopant solubility is proposed. The intrinsic relation among the evolution of Bi, reaction temperature and viscosity of the glass system is established. Importantly, the effective avenue to prevent the undesired deactivation of Bi during fiber drawing by tuning the temperature dependent viscosity evolution is built. By applying the strategy, for the first time we demonstrate the success in fabrication of heavily doped Bi active fiber. Furthermore, the principal fiber amplifier device is constructed and broadband optical signal amplification is realized. Our findings indicate the effectiveness of the proposed temperature dependent viscosity mediated strategy for developing novel photonic active fiber, and they also demonstrate the great potential for application in the next-generation high-capacity telecommunication system.

Global well-posedness of three-dimensional incompressible Boussinesq system with temperature-dependent viscosity

In this paper, we focus on the global well-posedness of solutions to three-dimensional incompressible Boussinesq equations with temperature-dependent viscosity under the smallness assumption of initial velocity fields u0 in the critical space Ḃ3,10. The key ingredients here lie in the decomposition of the velocity fields and the regularity theory of the Stokes system, which are crucial to get rid of the smallness restricition of the initial temperature θ0. In addition, we mention that the improved decay estimates in time is also necessary.

Influence of shear deformation on the formation of dynamic structure in protic ionic liquids. Representation of the temperature dependence of viscosity within the framework of Angell’s fragility concept

The rheological properties of a liquid containing two types of basic centers and hydroxyl groups (BGE-Im), as well as protic ionic liquids (ILs) derived from it, were studied in a wide range of shear rates (γ̇) (10−6–103 s−1) at various temperatures from 10 to 50 °C. Viscosity (η) of the BGE-Im does not depend on the scanning direction of shear stress (σ), i.e. this compound behaves like a Newtonian fluid over the entire range of σ. The dependence log η (1/T) of BGE-Im in Arrhenius coordinates is linear. Protonation of basic centers of BGE-Im leads to a strong increase in the viscosity of ILs obtained on its basis, and the temperature dependence of the viscosity of these ILs is described by the Vogel–Fulcher–Tammann (VFT) equation. It has been established that in the region of low shear rates, the viscosity of the ILs increases with decreasing shear rate, which leads to the appearance of a yield stress (σY). This indicates the formation of a fluctuation rheopectic structure in the ILs. In this sense, ILs are heterogeneous systems and their behavior is similar to that of highly concentrated suspensions and emulsions. For the first time, a quantitative comparison between the parameters of the VFT equation, the fragility (according to Angell’s model) of ILs, the relative coordination number of ILs molecules and the rheological yield stress characterizing the shear-induced fluctuation rheopectic structure of ILs has been made and the relationship between these characteristics has been shown.

A review on flow instability in hydro-viscous drive

Hydro-viscous drive (HVD) plays a significant role in smoothly transferring torque and flexibly regulating the velocity of the disks. By hydro-viscous drive, we mean that the viscous shear stress of the thin oil film between a multi-layer assembly of rotating parallel disks is generated to transmit torque and power. The laminar-to-turbulent transition is an extremely complicated issue due to the combined effects of squeeze and shear on the oil film within the microscale friction pair system. Hence, a comprehensive and thorough analysis of flow instability in fluid-thermal-solid interaction of tribodynamic behavior is highly desirable. Following a brief introduction of fundamentals of HVD, this paper provides an overall review on the instability mechanisms for three types of canonical flow dynamic models, i.e., plane squeeze flow, plane shear flow, and rotating-disk flow. The effects of various aspects of wall conditions and working media, such as surface microstructure, and temperature-dependent viscosity, on flow instability are then summarized, which can serve as a reference and guidance for optimizing the design of friction pair systems. Based on the review of the former progress, this paper not only explores the in-depth mechanisms regarding the laminar-to-turbulent transition in microchannel flow, but also provides the possibility of bridging the gap between flow instability and tribodynamic behavior.

Effect of Variable Viscosity on Entropy Generation Analysis Due to Graphene Oxide Nanofluid Convective Flow in Concentric Cylinders

Aggregated studies of graphene nanoparticles is important for the effective utilization of their striking thermophysical properties and extensive industrial applications. This investigation is one such computational study to explore the flow of graphene oxide nanofluids with temperature dependant viscosity between two concentric cylinders. Buongiorno model is used to develop the flow of graphene nanofluids including the impacts of Soret and Dufour effects and the effects of nanoparticle characteristics such as thermophoresis and Brownian motion. The modelled equations are transformed and are numerically solved using linearization method together with Chebyshev’s spectral collocation method under convective conditions. The impacts of embedded parameters on temperature, concentration and skin friction profiles of the chosen nanofluid and their consequent impacts on the predominant cause for the generated entropy are studied. From the tabulated values of Nusselt number and Sherwood number, it is observed that convective heat transfer can be enhanced by thermal Biot number whereas Soret number enhances diffusive mass transfer and variable viscosity parameter preferably reduces the skin friction. A comparison table is presented and it shows that the values obtained from the present method are in good agreement with existing literature. Also, the obtained results are depicted and interpreted in detail. Furthermore, entropy generation is analysed and its irreversibilty is calculated.

MHD Casson non-Newtonian fluid flow in a channel with expanding/contracting porous walls in the presence of thermal radiation

In this research, we explore the impact of changing viscosity in the context of the asymmetric laminar flow of Casson fluid with thermal radiation. The flow occurs within a channel that can either expand or contract, featuring porous walls. The flow equations are converted into ordinary differential equations (ODEs) through appropriate transformations to simplify the analysis. The velocity field and temperature profile expressions are obtained using Akbari-Ganji's method (AGM) and finite-element method (FEM). The graphs show the impact of different parameters on the flow characteristics, especially the viscosity-dependent parameter, Casson fluid parameter, and expansion ratio. The fluid velocity near the lower wall increases with the Casson fluid parameter but decreases after the mid-point. The fluid velocity is more affected by the temperature-dependent viscosity parameter for Newtonian fluid than non-Newtonian fluid. The results showed that as the Prandtl number increases, the temperature decreases, while the temperature increases with an increase in the Radiation parameter. Also, An increase in the wall expansion ratio leads to higher wall temperatures, whereas a decrease in the power-law index results in reduced temperatures. The results we've acquired were cross-referenced with prior studies, revealing that the employed methods exhibit high precision. The novelty of the present work is obtaining new results through the use of Akbari-Ganji's semi-analytical method.

Isothermal Oxidation and Thermal Shock Resistance of Thick and Porous LaMgAl11O19 Abradable Topcoat

An exploration of the plasma-sprayed abradable sealing coatings (ASCs) of a thick and porous LaMgAl11O19 topcoat onto SiC/SiC ceramic matrix composites (CMCs) is detailed in this study. Interlayers comprising Si/Si + Yb2Si2O7/Yb2SiO5 environmental barrier coatings (EBCs) were strategically employed, considering their function in protecting the SiC/SiC CMCs from recession and mitigating thermal expansivity misfit. An isothermal oxidation test was conducted at 1300 °C and resulted in the formation of bubble and glassy melt on the side surface of the coated sample, while a significant reaction layer emerged at the Yb2SiO5/LaMgAl11O19 interface near the edge. The localized temperature rise caused by the exothermic oxidation of the SiC/SiC substrate was determined to be the underlying factor for bubble generation. The temperature-dependent viscosity of the melt contributed to various bubble characteristics, and due to the enrichment of Al ions, the glassy melt exacerbated the degradation of the Yb2SiO5 layer. After a thermal shock test at 1300 °C, the substrate on the uncoated backside of the sample experienced fracture, while the front coating remained intact. However, due to the presence of a through-coating crack, an internal crack network also developed within the substrate.

Study of hybrid nanofluid flow in a stationary cone-disk system with temperature-dependent fluid properties

Cone-disk systems find frequent use such as conical diffusers, medical devices, various rheometric, and viscosimetry applications. In this study, we investigate the three-dimensional flow of a water-based Ag-MgO hybrid nanofluid in a static cone-disk system while considering temperature-dependent fluid properties. How the variable fluid properties affect the dynamics and heat transfer features is studied by Reynolds’s linearized model for variable viscosity and Chiam’s model for variable thermal conductivity. The single-phase nanofluid model is utilized to describe convective heat transfer in hybrid nanofluids, incorporating the experimental data. This model is developed as a coupled system of convective-diffusion equations, encompassing the conservation of momentum and the conservation of thermal energy, in conjunction with an incompressibility condition. A self-similar model is developed by the Lie-group scaling transformations, and the subsequent self-similar equations are then solved numerically. The influence of variable fluid parameters on both swirling and non-swirling flow cases is analyzed. Additionally, the Nusselt number for the disk surface is calculated. It is found that an increase in the temperature-dependent viscosity parameter enhances heat transfer characteristics in the static cone-disk system, while the thermal conductivity parameter has the opposite effect.

Thermal energy enhancement in blood conveying gold nanoparticles with temperature-dependent viscosity

Cancer is one of the universal popular healthcare problems, and there is a struggle to find advanced fresh medicines andidentify superior ways of distributing medications. Cancer is harmful and deadly to maximum of its patients. Cytotoxic agents are carried by cancer cells, to increase efficacy and protection. This reminds us that nanotechnology can be utilized for medicine. This current allegation has built into gold nanomaterials which could conquer and heal — it being the material considered like gold (atomic number 79). It gives a large amount of heat and contributes to the therapy of malignant tumors. Therefore, it is urgent to investigate the flow of blood-based gold nanoparticles over the porous medium for injection/suction effects. Time-dependent viscosity was used in Reynolds exponential model. The existence of magnetic field and nonlinear thermal radiation was integrated into the system. Ensuing equations were interpreted by its nondimensional model by applying comparison renovation. This Lobatto IIIA formula (known as bvp4c) was working to acquire multiple solutions. This findings indicate that temperature increases due to magnetic and radiation effects. Temperature and velocity profiles by injection are greater although related to the suction phenomenon. Further, the temperature and velocity augment by the inclusion of gold nanoparticles into blood flow.

Analysis of thermal conductivity variation in magneto-hybrid nanofluids flow through porous medium with variable viscosity and slip boundary

Hybrid nanoparticles, which are nanoparticles composed of multiple materials or phases, find applications in various fields due to their unique properties resulting from the combination of different materials. In such fluids, viscosity changes significantly in response to alterations in temperature or pressure. For example, these fluids become less viscous as they are heated and more viscous as they are cooled. Similarly, in certain situations, the application of a temperature variation can cause a change in viscosity. This property is commonly observed in materials like polymers and some oils. The article aims to investigate the heat transfer and flow behavior of fluid from an elastic sheet of hybrid nanoparticles, considering the temperature-dependent variable viscosity and thermal conductivity. The obtained equations for the mathematical model are partial differential equations converted to ODEs by applying a suitable similarity transformation. The findings show that the magnetic field opposes fluid motion. Our main findings are that adding nanoparticles to the base fluid significantly increased its heat conductivity. This improvement has great potential for uses requiring effective heat transmission, especially in engineering systems where heat dissipation plays a crucial role. The study also reveals the complex relationships that influence thermal conductivity, including slip boundary effects, viscosity fluctuations, magnetohydrodynamic effects, and porous media dynamics. Understanding these interactions is critical for optimizing heat transport processes in porous media applications. Comprehending these interplays is essential for refining heat transport mechanisms in applications involving porous media. The graphical representations are used to explain the physical behavior of various model parameters. Previous outcomes are also contrasted with the current ones. The findings show that the magnetic field opposes fluid motion.We range the subsequent list of values for parameters in every graph unless indicated accordingly.ϵ=0.1,Pr=2,M=0.5,R=0.2,K=5,fw=0.1,s=0.1 ,λ=1,φ1=0.02,φ2=0.04.

Temperature dependence of polymer melt viscosity obtained based on DSC data and the consistency between thermodynamic and kinetic fragility

AbstractThe viscosity of the polymer melt has an impact on both the processing and properties of the product. However, conventional viscosity measurement methods have limitations such as strict testing conditions, large sample sizes, and long response times. This paper proposes a simplified method that utilizes differential scanning calorimetry to determine the viscosity–temperature relationship of the polymer melt. The research subjects consist of four noncrystalline polymers and five crystalline polymers. A new thermodynamic fragility formula of crystalline polymer is obtained. Additionally, high‐temperature limiting viscosity shows a good linear relationship with fragility. Compared with the traditional viscosity measurement, this method is a simpler and more effective way to model the viscosity of polymer melt and has broad prospects in application.

Properties of Erythritol Tetranitrate from Molecular Dynamics Simulation.

The nonpolarizable force field for alkyl nitrates developed by Borodin et al. [J. Phys. Chem. B, 2008, 112, 734-742] has been employed to calculate selected properties of crystalline and liquid erythritol tetranitrate (ETN). The set of partial charges proposed by Borodin for pentaerythritol tetranitrate (PETN) was used except for a small correction to the H atom charges to ensure charge neutrality owing to the absence of the neopentyl carbon in ETN. The force field was used to compute the isothermal compression curve, lattice parameters, heat capacity, thermal expansivity, single crystal elastic constants, and Gruneisen parameters of crystalline ETN. The density- and temperature-dependent viscosities of liquid ETN are also reported. We anticipate that these data will be of some utility to the development of equations of state and thermomechanical models for ETN.