Surface Of Pipe Research Articles

Modeling and experimental comparison of pulsed-DC driven low-pressure plasma discharge in a metal tube

High-voltage pulsed-DC can be used to deposit films on the inner surfaces of tubes and pipes. However, the characteristics of the plasma discharge in the tubes and mechanisms of film deposition are not well understood. In this study, a discharge is formed in a metal tube inserted with a coaxial anode by microsecond (μs) pulsed power to explore the influence of the pulse parameters on the plasma characteristics, including the temporal and spatial evolution near the tube walls experimentally and by simulation. The discharge waveform is monitored by a voltage-current probe to analyze the impact of the electrical characteristics on the plasma. The plasma properties are diagnosed by a Langmuir probe and numerically calculated by the fluid model. The source voltage and current jointly influence the plasma density and electron temperature, and secondary electron emission by energetic ion bombardment affects not only the distribution of electron density measured by the probe, but also the temporal distribution during the pulse-on and pulse-off time. The electron temperature varies conversely with the density from the plasma zone to the cathode suggesting the typical glow discharge in the pulsed-DC tube. Secondary electron emission is created at a higher discharge frequency, and a sustained plasma between pulse cycles appears to be produced at a higher frequency. The results impart information about the pulsed-DC driven plasma discharge at low pressure as well as the role energetic ions play on the cathode and elucidate the mechanisms of plasma deposition on the interior tube wall.

Numerical study on heat and mass transfer performance of a natural draft wet cooling tower based on baffle optimization

In the natural draft wet cooling towers (NDWCTs), the resistance of the packing layer to air and the effect of the circular design of its cross-section, the air reaches the tower center area to overcome the maximum resistance. The air velocity in the center of the tower is low and the heat transfer is poor. To improve the performance of the cooling tower, the optimized design of the cooling tower distribution pipe surface with baffles is firstly investigated. Then, the three-dimensional numerical model of NDWCTs is developed and validated with power plant data. Finally, the effect of plates on cooling tower performance is analyzed through the influence of baffles on the cooling tower air field and combined with the circulating water temperature drop, evaporation, and ventilation. Results show that the air field uniformity inside the cooling tower is effectively improved by adding baffles. The cooling efficiency of the circulating water inside the cooling tower is improved. The air velocity in the packing zone is significantly increased by adding the a1a2 type baffle and the air temperature and circulating water in the central area of the tower decreases significantly and the a1a2 baffles performed best in terms of circulating water temperature drop in the packing zone and were able to significantly improve the cooling effect. The cooling tower with pro-wall baffles can cool the circulating water better than the conventional cooling tower. This study provides ideas for subsequent structural and energy efficiency studies.

Fabrication of silver nanoparticles loaded acacia gum/chitosan nanogel to coat the pipe surface for sustainable inhibiting microbial adhesion and biofilm growth in water distribution systems

Biofilm formation on the inner surfaces of pipes poses significant threats to water distribution systems, increasing maintenance costs and public health risks. To address this immense issue, we synthesized a nanogel formulation comprising acacia gum (AG) and chitosan (Cs), loaded with varying concentrations of silver nanoparticles (AgNPs), for using as an antimicrobial coating material. AgNPs were synthesized using AG as a reducing and stabilizing agent, exhibiting absorbance at 414 nm. The preparation of AgNPs was proved using TEM. Bactericidal efficacy was assessed against E. coli, Klebsiella pneumoniae, Enterococcus faecalis, and Bacillus subtilis. Using the dipping coating method, two pipe materials (polypropylene (PP) and ductile iron (DI)) were successfully coated. Notably, AgNPs2@AGCsNG nanogel exhibited potent antibacterial action against a wide range of pathogenic bacteria. Toxicity tests confirmed nanogel safety, suggesting broad applications. High EC50% values underscored their non-toxic nature. This research proposes an effective strategy for biofilm prevention in water systems, offering excellent antibacterial properties and biocompatibility. AG and Cs nanogels loaded with AgNPs promise to enhance water quality, reduce maintenance prices, and protect human public health in water distribution networks.

Assessing water quality in a distribution network based on hydraulic conditions

Abnormalities in hydraulic conditions inside a water distribution network are strongly related to the deterioration of drinking water quality. Leaking pipes and valves cause changes to the hydraulic conditions and allow the entry of impurities into the distribution system. Sudden flow and pressure shocks can detach soft deposits and biofilms from the pipe surface, resulting in deterioration of water quality. Online water quality measurements in a distribution network are scarce, but more common online flow and pressure measurements reveal the changes in hydraulic conditions in a distribution network and can be utilized to assess the water quality continuously and near real-time via modelling. Here, a data-driven model based solely on the online flow and pressure measurements in a distribution network for assessing the water quality at the end of an urban district metered area is presented. With the accuracy of R2 0.77, the developed data-driven model is able to assess the level of and the changes in potable water quality in a non-laborious and cost-effective way, also enabling proactive operations to ensure the distribution of high-quality drinking water to the consumers.

Experimental study on heat power of wet and pipe sections of wet/dry cooling tower with extended surface pipe exchanger

A hybrid system for recirculated water cooling of industrial enterprises is proposed. The major feature of the cooling system is a wet/dry cooling tower with an inner pipe exchanger. To enhance the heat transfer process, the outer surface of the heat exchanger pipe has fins. Design and function of the experimental setup are described. The goal of this work is to evaluate experimentally the heat power of the wet and pipe sections of the cooling tower. Results were presented as dependencies of the heat power in the wet/dry cooling tower on the mean gas velocity (from 0.89 to 3.20 m/s) and the ratio of the weight flow rates of the gas/liquid phases at various irrigation rates (13.7-35.6 m3/(m2.h)).

Enhancing heat transfer at low temperatures by laser functionalization of the inner surface of metal pipes

The latent heat transfer during vapour condensation in the condenser section of passive heat transport devices such as the two-phase closed thermosiphon is limited by film condensation. Dropwise condensation provides an increase of the heat transfer coefficient by up to one order of magnitude and can be achieved with a water-repellant surface. The inner surface of pipes made from stainless steel was functionalized by laser surface texturing with ultrashort laser pulses and subsequent storage in a liquid containing long-chained hydrocarbons. The pipes were separated into half-pipes by wire eroding to enable laser texturing of the inner surface, and were then joined by electron beam welding after laser texturing. As a result, superhydrophobic and water-repellent surfaces with a contact angle of 153° were obtained on the inner surface of the pipes with a length of up to 1 m. The functionalized pipes were used in the condenser section of a two-phase closed thermosiphon to demonstrate a heat transfer rate of 0.92 kW at 45 °C, which is approximately three times the heat transfer rate of 0.31 kW of a smooth reference pipe.

Advancement in understanding ultrasonic wave propagation in metallic pipes by simulation and experimental validation

ABSTRACT Ultrasonic gauging and defect detection of metallic pipes is a multi-disciplinary task, as it has to be performed in situ and involves several difficulties due to their curvature, limited access and corroded/eroded surface roughness due to harsh operating conditions. This research paper focuses on the investigation of employing a focused piezoelectric transducer in an immersion pulse-echo (PE) mode to measure the wall thickness (WT) from the inner side of the metallic pipes and to detect defects in the pipes. This paper also provides advances for understanding ultrasonic wave propagation in metallic pipes by simulation study using modern finite element technology and validating the results experimentally using battery-operated, water-immersible, IP67-grade stand-alone two-channel ultrasonic instrumentation that can move inside the pipe under test in flowing liquids such as water or oil. A simulation model has been established for time-of-flight (TOF) measurements for metallic pipes with various wall thicknesses, detection of standard defects and wall-thinning by inspecting the inner diameter (ID) surface of pipes and the pipe filled with water. The simulated results for the metallic pipes are in good agreement with the experimental data, providing an accurate and quantitative assessment of WT in the presence or absence of defects.

Micromechanical Analysis of Lateral Pipe–Soil Interaction Instability on Sloping Sandy Seabeds

The micromechanical mechanism of pipe instability under lateral force actions on sloping sandy seabeds is unclear. This study investigated the effects of slope angle and instability direction (upslope or downslope) on pipe–soil interaction instability for freely laid and anti-rolling pipes using coupled discrete element method and finite element method (DEM–FEM) simulations. The numerical results were analyzed at both macro- and microscales and compared with the experimental results. The findings revealed that the ultimate drag force on anti-rolling pipes increased with slope angle and was significantly larger than that on freely laid pipes for both downslope and upslope instabilities. Additionally, the rotation-induced upward traction force was proved to be the essential reason for the smaller soil deformation around freely laid pipes. Moreover, the shape differences in the motion trajectories of pipes were successfully explained by variations in the soil supporting force distributions under different slope conditions. Additionally, synchronous movement between the pipe and adjacent particles was identified as the underlying mechanism for the reduced particle collision and shear wear on pipe surfaces under a high interface coefficient. Furthermore, an investigation of particle-scale behaviors revealed conclusive mechanistic patterns of pipe–soil interaction instability under different slope conditions. This study could be useful for the design of pipelines in marine pipeline engineering.

Development of a Novel Water Jet Polisher Using Soft Abrasives for Small Complex-Structure Heat Pipes of Aluminum Alloy Produced Using Additive Manufacturing.

It is a challenge to polish the interior surface of a small bent pipe with complex structures and sizes less than 0.5 mm. This is because of the fact that traditional polishing methods could destroy, block, or break the small complex structures. For a small bent pipe made of aluminum alloy produced using additive manufacturing, the defects, such as adhered powders and spatters, are easy to jam the pipe without polishing, possibly resulting in catastrophic failure for aerospace applications. To overcome this challenge, a novel water jet polisher was developed using soft polymethyl methacrylate (PMMA) abrasives. After polishing a specific area, the adhered powders on the interior surface were reduced from over 140 to 2, 3, and 6 by the soft abrasives with mesh sizes of 200, 400, and 600, respectively. The surface roughness Sa was decreased from 3.41 to 0.92 μm after polishing using PMMA abrasives with a mesh size of 200. In comparison, silica abrasives were also employed to polish the small bent pipes, leading to the bent part of pipes breaking. However, this kind of failure was absent when using soft abrasives. Computational fluid dynamics calculations elucidate that a peak erosion rate of silica abrasives for a bent pipe with a turn angle of 30° is 2.18 kg/(m2·s), which is 17 times that of soft abrasives. This is why the small bent pipe was broken using silica abrasives, whereas it remained intact when polished with soft abrasives. In addition, water jet polishing has a lower erosion rate, a relatively smooth erosion curve, and less erosion energy, leaving the bent parts intact. The developed soft abrasive water jet polisher and the findings of this study suggest new possibilities for cleaning the adhered powders and spatters and polishing the interior surface of small bent pipes with complex structures.

Simulation of Pitting Corrosion Under Stress Based on Cellular Automata and Finite Element Method

Abstract A new cellular automaton (CA) program was written in python language to simulate the random pitting evolution process, which can not only obtain a variety of different corrosion products but also obtain a variety of common corrosion morphologies on the surface of metal pipes, bridge steel members, etc. In addition, commercial finite element (FE) software abaqus was redeveloped using python scripting language, and the FE mesh with the same size as the cellular mesh was established based on the consistent mesh algorithm, which ensured the efficiency and accuracy of the cyclic iterative algorithm. The stress and strain fields were calculated in real-time by applying the force load, the dissolution probability parameter P was updated in python according to the force-chemical coupling model, and a new corrosion morphology was obtained in python. At the same time, the birth and death element method was applied in abaqus to kill the corrosion elements in this iterative step simultaneously, and the new stress-strain field was recalculated in abaqus. The established consistent grid modeling strategy and cyclic iterative algorithm can significantly improve the solving efficiency of pitting evolution under the coupled action of corrosive medium and load. The results show that the stress concentration caused by pit expansion and the corrosion acceleration effect dominated by plastic deformation will promote each other, leading to the continuous growth of pitted pits. The established modeling strategy and cyclic iterative algorithm can significantly improve the solving efficiency of pitting evolution under the coupled action of corrosive medium and load.

A numerical study on control mechanism of heat transfer in a double pipe PCM heat exchanger by changing eccentricity

The thermal analysis of a double pipe phase change material heat exchanger is studied numerically. The study is done for three cases as; a) Case A: a melting process when inner pipe is maintained at a constant temperature higher than melting point, b) Case B: a solidification process when the inner pipe temperature is constant but less than melting temperature, and c) Case C: for a cyclic thermal storage when the inner pipe surface temperature periodically changes between temperatures of Cases A and B. The aim of this study is to find the optimum position of the inner pipe for each studied cases and to investigate the differences in heat transfer mechanism of the above cases for various Rayleigh numbers. The obtained results show that for Case A, the best position of the inner pipe depends on Rayleigh number, but the bottom region provides the shortest melting time for Ra>105. For the Cases B and C, the center must be preferred for all Reynolds numbers since the conduction heat transfer controls the process. In spite of many reported studies in literature, it is better to study on the enhancement of heat transfer for solidification rather than melting process.

Tracing the origins of plastics in biosolids: The role of sewerage pipe materials and trade waste

Plastics are ubiquitous in virtually every environment on earth. While the specific sources of plastics entering wastewater are not well known, growing evidence suggests sewage sludge (biosolids) can be a sink for plastics. One potential source could be the sewerage pipe materials used to transport sewage between premises and wastewater treatment plants (WWTPs). To evaluate the significance of sewerage piping as a source of biosolids plastics concentrations, we compared the proportion of the total network (by length and surface area) of polyethylene (PE), polyvinylchloride (PVC), and polypropylene (PP) pipes from 10 WWTPs against their biosolids mass concentrations (mg plastic/g biosolid). Among the 10 catchments, the percentage of the network consisting of PP piping ranged from 0 to 1 %, with 0.8–21 % for PE, and 8–73 % for PVC. Biosolids plastics concentrations ranged from 0.09 to 8.62 mg/g (mg plastic/g biosolid) for PP and PE, respectively. For all three plastics, there was no significant Pearson correlation (r < 0.4) between the biosolids concentration (dry weight mg/g) and the proportion of the network material of the sewerage piping as plastic (either length or surface area). A comparison of trade waste entering a subset of 6 WWTP showed the highest biosolid principal components analysis (PCA) associations between loads of plastics (g/day) and automotive wash bays, general manufacturing, hospitals, laboratories, food manufacturing, laundry and dry cleaning, and cooling towers. A stepwise regression analysis indicated pipe length and surface area, as well as automotive wash bays and food manufacturing may be significant. While our data gave mixed results on the attribution of the sources of plastics entering WWTPs, it suggests that sewerage infrastructure and trade waste may play some role. Future studies should investigate the leachability of sewerage infrastructure and contributions from specific trade waste categories to determine their significance in plastics entering WWTPs.

Process design for the laser functionalization of the inner surface of metal pipes for superhydrophobic wetting and enhanced heat transfer

Dropwise condensation in the condenser section of passive heat transport devices provides the potential for an improved heat transfer. In two-phased closed thermosiphons dropwise condensation can be achieved with a water-repellent surface on the inside of the pipes. However, the surface functionalization of the inner surface of the pipes is difficult due to the limited access to the inside of these pipes.Thus, the pipes with a length of up to 1 m were first separated into half-pipes by wire erosion, then functionalized by structuring with ultrashort laser pulses, subsequently stored in a solution of long-chained hydrocarbons, and finally rejoined by electron beam welding.As a result, superhydrophobic and water-repellent inner pipe surfaces with a contact angle of 153° were achieved. In the low temperature range at 45°C, the optimized thermosiphon allows for a heat transfer rate, which is three times the heat transfer rate of an untreated pipe surface.

ОЦЕНКА ЦЕЛЕСООБРАЗНОСТИ ИСПОЛЬЗОВАНИЯ ВОЗДУШНЫХ КОНДЕНСАТОРОВ С ДВИГАТЕЛЕМ СТИРЛИНГА В РЕКТИФИКАЦИОННЫХ УСТАНОВКАХ

Air cooling devices in which fans pumped the flow of atmospheric air have become widespread in industry. Many times, the energy cost of driving fans is less than the cost of water cooling, which includes the cost of both lifting water from reservoirs and moving water during circulating water supply. Also, most of the water losses are because of its evaporation. Using air cooling devices allows significant savings in cooling water, simplifies cleaning of the outer surface of heat exchange pipes. Currently, Stirling engines can contribute to global energy transformation, they are used as heat energy converters and can and can use any heat sources, the authors of the article propose a method for vapor condensation in rectification plants, where a Stirling engine is used as a fan drive and an estimated calculation method has been created. A schematic diagram of an upgraded rectification plant is presented. In the entire range of studies, under sufficiently favorable weather, the heat flow from steam in the proposed condenser with a Stirling engine can exceed 100 kW, which allows up to 300 tons of water per day to be withdrawn from the circulating water supply and will save over 15 kW of electricity. Studies have shown that the total heat flow does not depend on the efficiency of the Stirling engine, the energy of the condensing steam is spent on heating the air passing through the inter-tube space. With an increase in the power of the Stirling engine, an increase in thermal, heat transfer coefficient and minimum heat transfer surface area is observed.

In situ study of the interactions between metal surfaces and cationic surfactant corrosion inhibitors by surface-enhanced Raman spectroscopy coupled with visible spectroscopy.

Cationic surfactants are widely used as corrosion inhibitors for industrial tubings and pipelines. They protect the surface of steel pipes through a film-forming mechanism, providing both anodic and cathodic inhibition. To improve the efficiency of the corrosion protection, it is essential to understand the interactions between the surfactants and metal surfaces. To achieve this, surface enhanced Raman spectroscopy (SERS) can serve as a powerful tool due to its surface sensitivity and potential to detect trace amounts of analytes in complex media. In this contribution, we have investigated the behaviour of in situ prepared AgNPs in the presence of benzalkonium chloride as a model corrosion inhibitor using SERS coupled to visible spectroscopy and combined with light scattering methods. By combining these experimental methods, we were able to correlate the aggregation of silver particles with the concentration of added surfactant in the resulting mixture. Using this insight, we also established a SERS method for the detection of benzalkonium chloride traces in water. For this, we utilised the quenching of the SERS response of methylene blue by competitive adsorption of methylene blue and the surfactant on SERS active AgNPs. We believe that our approach can serve a variety of applications to improve the industrial water treatment. For example, the modelling of the interaction of different surfactants with SERS can be used for process intensification, and ultimately, to move towards the digital twinning of corrosion processes for more efficient corrosion inhibition. Furthermore, the ability to adapt our sensing protocol for on-line corrosion inhibitor monitoring allows a fast response to process changes, hence, enabling resource-efficient, continuous process control.

Determination of Thermal Conductivity of Nano-ceramic Thermal Insulation Coating on the Surface of a Heat Pipe

In the pursuit of conserving non-renewable fuel and energy resources and mitigating harmful emissions into the atmosphere, thermal insulation is commonly employed in practice for heated elements, including but not limited to building exteriors, boilers and furnaces, thermal power equipment, pipelines, and the like. The primary characteristic of any insulation material lies in its thermal conductivity, particularly under operational conditions. The research object is liquid nano-ceramic thermal insulation located on the surface of a round-section pipeline with a circulating heat carrier. The research subject is the thermal conductivity properties of the insulation material under operational conditions. The research aim is to determine the thermal conductivity coefficient of liquid nano-ceramic thermal insulation coating on the surface of the pipeline. The research method involves the laws of steady-state heat conduction and heat transfer for a two-layer cylindrical wall. Research findings indicate that for a steel pipeline measuring 76×3 mm with insulation thickness of 3.5 mm, the thermal conductivity coefficient of the liquid nano-ceramic thermal insulation material amounted to 0.0145 W/(m⋅K). Disregarding the radiative component, the thermal conductivity coefficient equals 0.0135 W/(m⋅K). Conclusions drawn suggest that the obtained value of the operational thermal conductivity coefficient of the liquid nano-ceramic thermal insulation material aligns with the manufacturer's claimed material thermal conductivity of 0.014 W/(m⋅K) and with the findings of other researchers. Minor discrepancies in magnitudes may be attributed to the extended period of insulation usage on the pipeline surface, which at the time of the conducted scientific investigations was approximately 1.5 years.

Landslide control in the excavation of a shallowly buried tunnel with a large front slope

The tunnel with a large front slope is a common type of entrance in mountain tunnels. Excavation of this type of tunnel disrupts the original balance of the slope, which can easily lead to landslides or collapses. It is therefore important to choose suitable support for early reinforcement. This paper presents a case study of landslide control during the tunnelling of a shallowly buried tunnel with a large front slope. Three types of pre-support, including anti-slide pile, pipe roof and surface grouting, were used to control the landslide. In addition, a three-dimensional analysis was carried out to investigate the reinforcing effect of single and multiple pre-supports on the landslide and tunnel structure. The results showed that the deformation of the landslide and tunnel structure at the end of the entrance was the greatest, that is, the most dangerous, and the maximum slope displacement without pre-support was 15.1 cm. In tunnel structures, the arch area was the most prone to instability, while the bottom area did not experience significant deformation. The horizontal displacement control effect of the landslide body was ranked from strong to weak as surface grouting, pipe roof, and anti-slide pile, which is a decrease of 4.8%, 20.5% and 40.8% compared to the maximum displacement. While the vertical displacement control effect of the landslide was ranked from strong to weak as pipe roof, surface grouting, and anti-slide pile, which is a decrease of 4.3%, 45.1% and 63.7% compared to the maximum displacement. The reinforcement effect when three types of pre-supports were applied simultaneously was basically equal to the sum of the reinforcement effects when each pre-support was applied separately. This is mainly due to the different reinforcement mechanisms and areas of the three pre-supports, resulting in better overall effects.

Experimental investigation of thermal performance and entropy analysis of sphere turbulators

In this study, the effects of different numbers of sphere turbulators placed in a circular-shaped test pipe under turbulent flow conditions on heat transfer, friction factor, thermal performance factor and entropy production were experimentally investigated. Water was used as the working fluid in the experiments carried out in the number range Re=8379-16701. Initially, plain pipe and supported plain pipe experiments were carried out by keeping the fluid inlet temperature and test pipe surface temperature constant. Then, 1, 2 and 3 sphere turbulator experiments were carried out under the same conditions, respectively. According to the findings, the maximum Nusselt number increase compared to the supported plain pipe was 83.34% for the test pipe with 3 sphere turbulators. The minimum and maximum Nu number increase rates of 3 sphere turbulators compared to 1 and 2 sphere turbulators were obtained as 42.61%-46.93% and 13.99%-17.11%, respectively. The increase rates of maximum friction factors of 1, 2 and 3 sphere turbulators compared to the supported plain pipe were 174.42%, 226.70% and 306.53%, respectively. In addition, the maximum total entropy rate for sphere turbulators was obtained as 0.058 W.m-1.K-1 for 1 sphere turbulator at Re = 8379. In terms of the second law, the maximum entropy generation of sphere turbulators compared to the supported plain pipe decreased by 79.39% for 3 sphere turbulators at Re = 8379. As a result, it was concluded that the optimum number of sphere turbulators is 3 sphere turbulators with the lowest entropy production number and the highest TPF value (1.28).

Evaluation of the Primary Pipe Network at Banua Anyar Booster Pump as an Effort to Reduce Water Loss in the Service area of Northern Banjarmasin, South Kalimantan

Recorded as the best PDAM in South Kalimantan in Banjarmasin City. PT. Bandarmasih Perseroda Drinking Water (PAM Bandarmasih) is still facing the problem of high water loss rates of 29.07% in 2022, which is still far above the National Medium Term Development Plan (RPJMN) target with a minimum water loss value of 20%. One of the ways PDAM can reduce water loss is by evaluating the pipe network in a District Meter Area (DMA). This research focuses on evaluating the primary pipe network in the area served by the Banua Anyar booster which serves 18 DMAs. Network evaluation using EPANET 2.0 software. The evaluation results show that the diameter of the primary pipe from the booster pump to the Banua Anyar pipe bridge has quite high unit-head loss and flow velocity values due to flow friction with the pipe surface. It is necessary to change the diameter of the primary pipe used in the Banua Anyar booster network from a diameter of 400 mm to 600 mm which can reduce the rate of water loss by 6.3%. In the future, it is hoped that the value of water loss at PDAM Banjarmasin City can be reduced and the affordability of drinking water services for the people of Banjarmasin City can increase.

Numerical and experimental investigations on quasi-static component generation of longitudinal wave propagation in isotropic pipes

In this paper, the quasi-static component (QSC) generation of longitudinal waves propagating in an isotropic pipe is investigated numerically and experimentally. The three-dimensional (3D) finite element (FE) simulations are first carried out to gain physical insights into the characteristics of QSC generation from longitudinal wave travelling in an isotropic pipe with weak material nonlinearity. By applying the axial displacement excitation in the FE model, L(0, 1) mode and L(0, 2) mode are excited simultaneously. Then, the generated QSC pulses are extracted using the phase reversal approach for analysis. It is found that the QSC pulses generated by L(0, 2) mode and L(0, 1) mode are L(0, 1) mode. Meanwhile, the shapes of QSC pulses at different locations are extracted and compared. In this study, a data pre-processing method is proposed to handle numerically calculated and subsequent experimentally measured displacement signals, and a nonlinear acoustic parameter is defined to evaluate the incipient damages. After that, an experiment is conducted to measure the QSCs induced by the propagation of longitudinal waves in an aluminum pipe. The experimental results indicate that the propagation of longitudinal waves in the aluminum pipe can induce the QSCs. Different levels of corrosion are created on the surface of the aluminum pipe and are assessed by the generated QSCs. The results show that the nonlinear acoustic parameter has a monotonically increasing trend with the growing severity of corrosion. The QSCs generated by longitudinal wave can be used to detect and evaluate the early-stage surface corrosion in the aluminum pipe.