Large Surface Area Research Articles

Pd Nanoparticle Supported on N‐Doped Carbon Derived from Sodium Alginate/Melamine Blends as Efficient Heterogeneous Catalyst for Heck Reactions

AbstractN‐doped porous carbon shows great potential in the field of heterogenous supports due to its high porosity, large surface area, rich active sites, and strong chelation with catalytic active metals species. Herein, we successfully prepared a novel N‐doped porous carbon derived from sodium alginate/melamine blends (SAMNC) with different mass ratio through a simple carbonization and activation process. Hierarchical porous structure of the derived N‐doped carbon has been confirmed with the SEM, TEM, and N2 adsorption characterization. After Na2PdCl4 solution impregnation and further reduction process, Pd0 nanoparticles have been uniformly immobilized on the SAMNC support to produce novel Pd@SAMNC catalyst. The optimal Pd@SAMNC‐0.6 possesses a high N content (5.13%), Pd content (5.90%), large BET specific surface area of 1884.5 m2·g−1. Positron annihilation lifetime spectroscopy (PALS) investigation of the porous carbon materials provided the sub‐nano level microporous information proofs of Pd@SAMNC‐0.6 had the capability to provide more active sites for reactions than commercial Pd supported on activated carbon (Pd@AC). Pd@SAMNC‐0.6 catalyst showed superior catalytic efficiency in Heck coupling reaction between aromatic halides and alkenes and can be recycled for 17 runs without significant decrease in catalytic efficiency.

Study on Freeze–Thaw Resistance of Cement Concrete with Manufactured Sand Based on BP Neural Network

In this study, experiments were conducted on the freeze–thaw performance of manufactured sand cement concrete with different sand ratios and fly ash contents. The research found that during 200 freeze–thaw cycles, as the fly ash content increased, the concrete exhibited a higher mass loss rate and a decline in the relative dynamic modulus of elasticity. This was due to the lower activity of SiO2 and Al2O3 in the fly ash, which reduced the hydration products. Incorporating an optimal amount of manufactured sand can increase the density of concrete, thereby improving its resistance to freeze–thaw cycles. However, when the content of manufactured sand was high, its large surface area could interfere with the hydration process and reduce strength, thereby diminishing the freeze–thaw resistance of the concrete. Given that studying the freeze–thaw resistance of manufactured sand concrete is time-consuming and influenced by many factors, a prediction model based on a BP (back propagation) neural network was developed to estimate the mass loss rate and the relative dynamic modulus of elasticity following freeze–thaw cycles. After validation, the model was found to be highly reliable and could serve as a foundation for mix design decisions and freeze–thaw performance prediction of manufactured sand cement concrete.

Silicon Nanowires via Metal-Assisted Chemical Etching for Energy Storage Applications.

Silicon nanowires (SiNWs) have demonstrated great potential for energy storage due to their exceptional electrical conductivity, large surface area, and wide compositional range. Metal-assisted chemical etching (MACE) is a widely used top-down technique for fabricating silicon micro/nanostructures. SiNWs fabricated by MACE exhibit significant surface areas and diverse surface chemistry. Since the material composition and surface chemistry have a significant impact on the electrochemical energy storage performance, integrating SiNWs with diverse materials like porous carbon, metal oxides/sulfides, and polymers, can establish composites with excellent properties. Hence, it is imperative to meticulously fabricate SiNW-based materials with customizable morphologies and enhanced electrochemical energy-storage performance. This review provides an in-depth study of recent advancements in SiNW-based materials with enhanced performance for energy storage systems, such as supercapacitors (SCs) and lithium-ion batteries (LIBs). It includes a concise overview of the history, MACE synthesis, and characteristics of SiNWs. Further, it also explores the key elements that influence the MACE process of SiNWs and delves into structural engineering. Additionally, we introduce recent advances in SiNW-based materials for the design of high-performance energy-storage devices, namely SCs and LIBs. Finally, we present the crucial future prospects of SiNW-based materials for energy-storage applications.

Influence of enhanced Laves phase shape and distribution on atomic-scale frictional wear mechanisms in nickel-based single crystal alloys

Abstract This study aims to simulate the influence of different shapes and distribution states of Laves phases on the friction-wear behavior of nickel-based alloys using molecular dynamics (MD). The investigation systematically examined the mechanical properties, friction coefficient, number of worn atoms, dislocations, temperature, and other micro-deformation behaviors of materials incorporating horizontally and vertically distributed short rod-shaped, spherical, and short strip-shaped Laves phases. The presence of the Laves phase significantly impedes temperature transfer, defect motion, and atomic displacement in the workpiece, resulting in reduced dislocation glide rate and shorter average dislocation lengths. High dislocation densities accumulate at the Laves/γ phase interface, enhancing surface wear resistance. The short rod-shaped Laves phase, due to its large surface area at the Laves/γ interface, impedes defect motion more effectively than spherical and short strip-shaped phases. dislocation tangle, higher friction force, fewer worn atoms, a higher friction coefficient, and improved wear resistance. However, vertically distributed short strip-shaped and short rod-shaped Laves phases exhibit less effective defect interaction, resulting in increased wear and significant deformation. The spherical Laves phase, with its geometric symmetry, shows consistent wear resistance regardless of distribution state. Short rod-shaped Laves phase provides the best reinforcement due to its effective defect motion impedance, while the spherical Laves phase offers stable performance across different distribution states, making it the most suitable shape for Laves phase reinforcement.

A Time-Interval Strategy to Prepare Porous SiO2 Spheres with Adjustable Core-Shell Ratio for Multiple Guest Loading.

Porous microspheres with desired pore size and distribution are in high demand for loading various guest materials, especially various pollutants that are several nanometers in size or stably suspended in liquid. Herein, multilevel porous SiO2 microspheres with arbitrarily adjustable core-shell ratios are prepared by solely regulating the time interval between the start of the hydrolysis reaction and the addition of organic solvent. The core-shell ratio of the SiO2 microspheres increases gradually with prolongation of the addition time interval; meanwhile, the specific surface area can be adjusted from 543.2 m2 g-1 to 992.9 m2 g-1, and the average pore diameter varies from 2.3 to 5.7 nm together with a high pore volume reaching 0.91 cm3 g-1. Moreover, the hierarchical core-shell SiO2 microspheres with an adjustable core-shell ratio, a large specific surface area, and a multilevel pore size could be obtained on a large scale. These SiO2 microspheres demonstrate excellent performance in coloading platinum nanoparticles and various dye molecules, suggesting their great potential in treating various pollutants in printing and dyeing wastewater.

Hydrophilic and Hydrophobic: Modified GeO2 Aerogels by Ambient Pressure Drying

An ever-increasing number of applications of oxide aerogels places a high demand on wettability-tuning techniques. This work explores the possibility to cheaply prepare GeO2 aerogels with controlled wettability by an ambient pressure drying (APD) method. GeO2 aerogels are prepared via two synthetic routes. Surface modification is carried out by soaking the gels in a silylating agent solution; type and concentration of the modifier are optimized to achieve a large surface area. The aerogels have been characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, nitrogen adsorption and contact angle measurements. The effect of surface modification on the phase composition and particle size of the aerogels is described. In summary, the work provides a new cheap production method for the preparation of both hydrophobic and hydrophilic GeO2 aerogels with contact angle varying from 30° to 141° and with surface area of 90–140 m2/g, which facilitates the expansion of their diverse applications. GeO2 aerogel synthesis by APD is reported for the first time.

Preparation of alkyl microporous organic network-based capillary column for an efficient gas chromatographic separation of position isomers.

The large surface area, excellent thermal stability and easy modification make microporous organic networks (MONs) good candidates in the field of gas chromatography (GC). Due to the limited species and highly conjugated networks of MONs, their applications are still in infancy and restricted. To accelerate their developments and to enrich their types in GC, here we report the first example of synthesizing alkyl MON and its capillary column for GC separation of position isomers. Linear 1,8-dibromooctane is used as the alkyl monomer instead of traditional aromatic ones to construct novel alkyl MON to decrease the inherent conjugated characteristic of MONs. The alkyl MON exhibits good thermal stability (up to 350°C), large surface area (1173m2g-1), and non-polar character, allowing good resolution for alkanes, alkyl benzenes, alcohols, ketones, and diverse position isomers, including dichlorobenzene, trichlorobenzene, bromotoluene, nitrotoluene, methylbenzaldehyde, and ionone with the limits of detection (0.003mgmL-1) and limits of quantitation of (0.10mgmL-1). The in situ growth-prepared alkyl MON column demonstrates remarkable duration time and precisions for the retention relative standard deviations, (RSDs%, intra-day, n=7), 0.06%-0.53% (intra-day, n=7), and 2.87%-10.59% (column-to-column, n=3). In addition, the fabricated alkyl MON-coated capillary column offers better resolution than three commercial GC columns for the resolution of methylbenzaldehyde, bromotoluene, and chlorotoluene isomers. This work reveals the practicability for synthesizing alkyl MONs and demonstrates their prospects for position isomers separation.

MoS2_CNTs_aerogel-based PEDOT nanocomposite electrochemical sensor for simultaneous detection of chloramphenicol and furazolidone in food samples

Toxic intermediates in food caused by chloramphenicol (CP) and furazolidone (FZ) have gained interest in research toward their detection. Hence, fast, reliable, and accurate detection of CP and FZ in food products is of utmost importance. Here, a novel molybdenum disulfide-connected carbon nanotube aerogel/poly (3,4-ethylenedioxythiophene) [MoS2/CNTs aerogel/PEDOT] nanocomposite materials are constructed and deposited on the pretreated carbon paste electrode (PCPE) by a facile eletropolymerization method. The characterization of MoS2/CNTs aerogel/PEDOT nanocomposite was analyzed by scanning electron microscopy (SEM), cyclic voltammetry, and differential pulse voltammetry. The modified MoS2/CNTs aerogel/PEDOT nanocomposite has improved sensing characteristics for detecting CP and FZ in PBS solution. For this work, we have studied various parameters like electrocatalytic activity, the effect of scan rates, pH variation studies, and concentration variation studies. Under optimum conditions, the modified electrode exhibited superior sensing ability compared to the bare and pretreated CPE. This improvement in electrocatalytic activity can be the higher conductivity, larger surface area, increased heterogeneous rate constant, and presence of more active sites in the MoS2/CNTs aerogel/PEDOT nanocomposite. The modified electrode demonstrated distinct electrochemical sensing toward the individual and simultaneous analysis of CP and FZ with a high sensitivity of 0.701 µA. µM−1 .cm−2 for CP and 0.787 µA. µM−1 .cm−2 for FZ and a low detection limit of 3.74 nM for CP and 3.83 nM for FZ with good reproducibility, repeatability, and interferences. Additionally, the prepared sensor effectively detects CP and FZ in food samples (honey and milk) with an acceptable recovery range and a relative standard deviation below 4%.

Enhanced Photocatalytic Degradation of Cr (VI) and Organic Pollutants Using Novel 3D/2D MoS2/SnS2 Heterostructures for Water Remediation

Abstract In this study, 3D flower-like MoS2 nanostructures were synthesized using a hydrothermal technique to form heterostructures with 2D porous SnS2 nanosheets. The resulting 3D/2D MoS2/SnS2 heterostructures were evaluated for their photocatalytic abilities in removing Cr (VI), tetracycline (TC), and methylene blue (MB) under simulated solar irradiation. The results demonstrate that the MoS2/SnS2 heterostructures significantly outperformed pristine MoS2 and SnS2 in photocatalytic efficiency. Specifically, the MoS2/SnS2 photocatalysts achieved 99.9% degradation of Cr (VI) within 50 minutes, 96% degradation of TC in the same timeframe, and 99.9% elimination of MB in just 10 minutes. The reduction rate constant for Cr (VI) reduction by MoS2/SnS2 photocatalysts was 0.117 min−1, surpassing that of pure SnS2 (0.007 min−1) and MoS2 (0.0034 min−1) by 16 and 30 times, respectively. This outstanding performance is attributed to the heterojunction formation between SnS2 and MoS2, which suppresses the recombination of photogenerated charge carriers and provides abundant reactive sites due to their large specific surface area. The proposed photodegradation mechanism illustrates the facilitated migration of photogenerated charge carriers under light irradiation, enabled by the energy band alignment at the MoS2/SnS2 interface. These findings represent a significant advancement in the development of photocatalysts based on 3D flower-like MoS2 and porous SnS2 nanostructures, offering promise for applications in wastewater treatment and environmental remediation.

Construction of MXene interlayer conductive ion transport channel by polypyrrole-coated cellulose nanofibers for ultralow voltage high-performance ionic soft actuators

Ionic soft actuators are extensively utilized in soft robotics and intelligent flexible devices due to their low-voltage actuation capability. MXene(Ti3C2Tx) has potential value as an electrode material for ionic soft actuators owing to its high conductivity and large specific surface area. However, the actuation performance of its ionic soft actuator is limited by poor extensibility and low capacitance caused by the stacking effect. Here, a high-performance ionic soft actuator with MXene\\polypyrrole-coated cellulose nanofibers (CNF@PPy) is reported. While gaining high flexibility of the electrode due to the great mechanical property of CNF, the fast conductive transport channel is constructed by doping CNF@PPy between MXene layers, which not only effectively reduces the loss of conductive properties and drastically improves the ion migration rate, but also prevents MXene from stacking and has additional chemical active sites, significantly increasing its ion storage capacity. Consequently, the actuator exhibits excellent actuation performance at the 0.5 V ultralow voltage: 0.79 % bending strain, 6 s rapid response, and 91.03 % high durability after 5 hours. Additionally, the potential for the actuating core of advanced flexible electronic devices is demonstrated by the application of flexible forceps and the flexible electronic eye.

Coating effect of polyurethane-layered double hydroxide nanocomposite on steel

The motivation behind this work is the preparation of polyurethane-magnesium aluminum layered double hydroxide (PU-LDH) nanocomposite and its application as a coating for steel protection. The coating was prepared with different doses of LDH, ranging from 0 to 2% of the coating weight. The effect of different concentrations on the mechanical, adhesion, and surface properties of PU coating is studied. Firstly, LDH was prepared via the coprecipitation process and then distributed in PU matrix. The nanocomposites were then crosslinked in the form of coating layers on steel. The preparation of the thermally stable crystalline LDH nanoparticles with 89 nm particle size was confirmed by FTIR, XRD, DLS, and TGA. SEM photos showed the dispersed and intercalated structure. The coating characteristics demonstrate that addition of LDH decreased the drying time and increased the dry film thickness of PU up to 1.5% due to the crosslinking between the large surface area nanofiller and polyurethane matrix. Furthermore, the prepared LDH nanofiller increased the adhesion strength, impact resistance, abrasion resistance, modulus, and flexibility of PU due to the strong polymeric network structure. The 2% nanocomposite coating shows poor properties due to the excess concentration and heterogeneous dispersion of nanoparticles within the PU polymer. The resistance to fire and some chemicals was supported by the thermally and physically stable LDH nanoclay. The former characterizations state that the proposed PU-LDH nanocomposite is an enhanced and applicable coating.

Electrospun Nanofiber-Based Biosensors for Foodborne Bacteria Detection

Food contamination has emerged as a significant global health concern, posing substantial challenges to the food industry. Bacteria are the primary cause of foodborne diseases. Consequently, it is crucial to develop accurate and efficient sensing platforms to detect foodborne bacteria in food products. Among various detection methods, biosensors have emerged as a promising solution due to their portability, affordability, simplicity, selectivity, sensitivity, and rapidity. Electrospun nanofibers have gained increasing popularity in enhancing biosensor performance. These nanofibers possess a distinctive three-dimensional structure, providing a large surface area and ease of preparation. This review provides an overview of the electrospinning technique, nanofibers and nanofiber-based biosensors. It also explores their mechanisms and applications in the detection of foodborne bacteria such as Salmonella, Listeria monocytogenes (L. monocytogenes), Escherichia coli (E. coli), Staphylococcus aureus (S. aureus) and Pseudomonas putida (P. putida).

Electrochemical Performance of Niobium MXenes with Lanthanum.

MXenes are the newest class of two-dimensional nanomaterials characterized by large surface area, high conductivity, and hydrophilicity. To further improve their performance for use in energy storage devices, heteroatoms or functional groups can be inserted into the Mxenes' structure increasing their stability. This work proposes insertion of lanthanum atoms into niobium-MXene (Nb-MX/La) that was characterized in terms of morphogy, structure, and electrochemical behavior. The addition of La to the Nb-MXene structure was essential to increase the spacing between the layers, improving the interaction with the electrolyte and enabling charge/discharge cycling in a higher potential window and at higher current densities. Nb-MX/La achieved a specific capacitance of up to 157 mF cm-2, a specific capacity of 42 mAh cm-2 at 250 mV s-1, a specific power of 37.5 mW cm-2, and a specific energy of 14.1 mWh cm-2 after 1000 charge/discharge cycles at 50 mA cm-2.

Investigation on a sustainable magnesium phosphate cement (MPC) with recycled waste MPC powders

Magnesium phosphate cement (MPC) has been used for the structure rapid-repair of damaged buildings. To reduce the cost and resource consumption during MPC preparation, recycled MPC powders were used to prepare an environmental-friendly MPC by replacing the dead burned MgO powders. The workability and early hydration temperature development of MPC paste with recycled powders were investigated. To characterize the effect of recycled powders on the performance of the MPC paste, the mechanical properties, volume stability, phase developments and microstructures were determined. The results showed that due to the small particle size and the large specific surface area, the recycled powders absorbed part of the water during the mixing and reduced the fluidity of the MPC paste. The chemical reaction activity of recycled powders was lower than that of MgO powders, resulting in the reduction of the hydration reaction rate and hydration products of MPC. With the recycled powder content increasing, the mechanical strength and volume stability of MPC decreased. The decreased strengths could be attributed to the poor MPC paste structure with increased pores and microcrack content caused by recycled powders. Nevertheless, when the recycled powder content was 40 %, MPC paste obtained a workability of 20.8 cm, setting time of 24.75 min, 3-h compressive strength of 30.9 and 28-d compressive strength of 50.3 MPa. Therefore, under this replacement rate, the MPC paste still had acceptable properties, which could still meet the rapid-repair requirements.

Preparation of an imidazolium-based poly(ionic liquid) functionalized magnetic three-dimensional graphene oxide for magnetic solid phase extraction of pyrethroids from tea samples

In this work, an imidazolium-based poly(ionic liquid) (poly(1-dodecyl-3-vinyl-imidazolium bromide) functionalized magnetic three-dimensional graphene oxide (Fe3O4@3D-GO@poly(ImC12+Br−)) was synthesized via a vacuum freezing-drying method and used as a magnetic solid phase extraction (MSPE) adsorbent for the efficient extraction of pyrethroid pesticides from tea samples. The prepared Fe3O4@3D-GO@poly(ImC12+Br−) was confirmed by scanning electron microscopy (SEM), Fourier transform infrared spectrometry (FT-IR), vibrating sample magnetometer (VSM) and X-ray photoelectron spectrogram (XPS). Due to its large specific surface area and the ability to offer multiple intermolecular interactions, including π-π stacking, hydrophobic and hydrogen bond interactions, the prepared Fe3O4@3D-GO@poly(ImC12+Br−) showed high extraction efficiency for pyrethroids. The experimental parameters were optimized by a combination of single-factor method and Box-Behnken design to improve the extraction efficiency. Under the optimum conditions, coupled with high performance liquid chromatography (HPLC), a sensitive analytical method was developed for the determination of pyrethroids, and the proposed method showed wide linear ranges (1.00–100 μg L−1) with correlation coefficients (R) ranging from 0.9980 to 0.9994, low limits of detection (0.100 μg L−1) and good repeatability with intra-day relative standard deviations (RSDs) in the range of 2.90–5.53 % and inter-day RSDs in the range of 1.83–7.76 %. Moreover, the developed method was successfully applied to the determination of pyrethroids in tea samples and satisfactory recoveries ranging from 82.37 % to 114.34 % were obtained. The results showed that the developed Fe3O4@3D-GO@poly(ImC12+Br−) was an ideal, effective and selective material for the extraction and enrichment of pyrethroids from tea samples.

Enhancing electricity generation from water evaporation through cellulose-based multiscale fibers network

Harvesting energy from the water − solid interface through natural water evaporation provides a promising approach for generating sustainable electricity to power self-powered electronics. Advancing the bio-based hydrovoltaic materials enhances sustainability, with wood as a viable candidate due to the inherent hydrophilic and charged properties. However, current wood-based water evaporation-induced electricity generators (WEIGs) mainly depend on the “top-down” construction strategies. Wherein, the improvement of power density is constrained by the limited structural regulation, nondiverse building blocks, and monolithic enhancement mechanisms. Here, the high-performance wood-based WEIGs based on multiscale fibers network (MFN) are reported by embedding the Ti4O7 nanofibers (T4NF) inside the assemblies of TEMPO-oxidized cellulose nanofibrils (TOCNF) through a “bottom-up” route. Benefiting from the large specific surface area, high surface potential, and photothermal effect of conductive T4NF, the WEIG achieves a high short-circuit current of ∼13.7 μA while delivering ∼0.94 V open-circuit voltage. This work presents an efficient method to boost performance while understanding the impact of functional MFN on water evaporation.

Transformation of waste thermocol into activated carbon for electrochemical detection of ammonia in an aqueous solution

In this study, waste thermocol sheets are used to synthesize activated carbon (AC) for the electrochemical detection of ammonia in an aqueous solution. The AC is characterized for its morphology, structure, and chemical composition via standard characterization techniques. AC shows promise for detecting ammonia in aqueous solutions due to its high adsorption capacity from large surface area and porosity. The electrochemical approach used to detect ammonia (NH3) in electrolyte solutions uses an AC electrode and is based mostly on the electro-oxidative conversion of ammonia species at the electrode's interface. AC electrodes fabricated on flexible conductive fabric (CF) are used for the electrochemical detection of ammonia at pH 6. The electrochemical sensing of ammonia in aqueous solutions involves its oxidation on the electrode's surface. Cyclic Voltammetry (CV) experiments were conducted over a pH range of 5 to 8, revealing optimal current responses at pH 6. Therefore, phosphate-buffered saline (PBS) at pH 6.0 was employed for all electrochemical analyses. Various concentrations of ammonia (10–100 ppm) were investigated within a voltage window of −0.3 V to 0.3 V, with current signals increasing proportionally with ammonia concentration. The limits of detection (LOD) and quantification (LOQ) were determined to be 28.55 ppm and 86.54 ppm, respectively. An incubation period of 3 min was observed for ammonia concentrations ranging from 0 to 40 ppm. Selectivity evaluations were conducted by assessing interference effects from ethanol (E), methanol (M), toluene (T), and uric acid (UA), revealing ammonia's distinctive peak, indicative of superior selectivity. Notably, the electrode exhibited remarkable stability, retaining approximately 95 % of the original signal over a 5-week duration. The reproducibility of the fabricated electrodes shows significant results. The repeatability was performed at room temperature in a buffer solution of pH 6 and at a 40-ppm concentration of ammonia and has shown almost similar results. Therefore, the fabricated AC sensing electrode has shown prominent stability, reproducibility, and repeatability. These sensing electrodes can be very beneficial for sensing applications.

Wood- and Manure-Derived Biochars Reduce Antibiotic Residues and Shift Antibiotic Resistance Genes and Microbial Communities in Manure Applied Forage–Soil Systems

The increasing use of antibiotics in livestock poses environmental risks, leading to contamination of agricultural soils and propagation of microbial antibiotic-resistant genes (ARGs). This study examined the impacts of wood- and manure-derived biochar (BC) on antibiotic residues, ARGs, and microbial communities in sandy loam and clay loam soils amended with manure in Cynodon dactylon pastures. We hypothesized that BC amendments would influence the degradation of antibiotics and the structure of microbial communities based on their physicochemical properties and soil types. Our results demonstrated that wood BC reduced the concentrations of tetracycline and sulfonamides, particularly in sandy loam soil, due to its larger surface area and hydrophobic properties. In contrast, manure BC provided additional nutrients and supported atmospheric nitrogen-fixing microbial groups, especially in clay loam soil, while exhibiting variable efficiency in reducing antibiotic residues due to its lower surface area and higher ash content. These findings underscore the differential impacts of each BC type, emphasizing the need for tailored BC applications based on soil type to effectively mitigate antibiotic contamination and promote sustainable agricultural practices. In conclusion, wood BC was more effective in enhancing soil health by reducing antibiotic residues and improving microbial diversity, particularly in sandy loam soils, while manure BC was beneficial for nutrient cycling in clay loam soils.

In-situ grown MXene@PDA/MOF composites constructed electrochemical sensor for detecting trace l-cysteine

In this study, novel honeycomb-like morphology MXene@PDA/MOF composites were prepared in situ on the surface of MXene@PDA (polydopamine), combined with 2-methylimidazole and Zn2+. The characterizations of morphology and electrochemical properties show that MXene@PDA/MOF has large specific surface areas and outstanding electroconductibility. Furthermore, the MXene@PDA/MOF-based sensor was fabricated to detect l-cysteine (L-Cys). The response of differential pulse voltammetry (DPV) shows the current intensity increases as l-Cys concentration. Under the optimum conditions, DPV response shows a fine linear relationship with l-Cys concentration in a range of 0.01 – 5.0 μmol L−1 with the detection limit of 3.74 × 10−9 mol L−1. This sensor was used to detect l-Cys in real samples with recoveries of 100.34 % – 101.68 %. Thus, the MXene@PDA/MOF-based electrochemical sensor exhibits excellent selectivity, reproducibility, stability, and practicability.

Zinc cobaltite embedded in binary metal-organic frameworks using a direct binder-free electrode fabrication approach for efficient energy storage devices and monosodium glutamate detection

There is an imperative need to develop high performance electrode for advance energy storage devices. This work represents the successful synthesis of zinc cobaltite (ZnCo2O4), nickel cobalt metal organic framework, and their composite (ZnCo2O4@NiCo-MOF). The materials are synthesized by using both hydrothermal and sonication techniques. The ZnCo2O4 offers eco-friendly and diffusion regulated properties, while NiCo-MOF provides large specific surface area and tunable pore structure. The ZnCo2O4@NiCo-MOF provide superior electrochemical performance compared to ZnCo2O4 and NiCo-MOF in a three electrode setup. The ZnCo2O4@NiCo-MOF provides a specific capacity of 984 C/g at 1.5 A/g. The ZnCo2O4@NiCo-MOF is also utilized in two electrode setup with activated carbon. The ZnCo2O4@NiCo-MOF//AC device demonstrates the energy density of 92.4 Wh/kg and a power density of 930 W/kg. Additionally, the real time application of ZnCo2O4@NiCo-MOF electrode is also tested in the detection of monosodium glutamate in food. This study highlights the importance of ZnCo2O4@NiCo-MOF electrode materials for future storage and detection devices.