Speckle Interferometry Research Articles

Suitability of DIC and ESPI optical methods for monitoring fatigue damage development in X10CrMoVNb9-1 power engineering steel

The aim of this research was to compare the effectiveness of two different optical measurement techniques (digital image correlation—DIC and electronic speckle pattern interferometry—ESPI) during fatigue damage development monitoring in X10CrMoVNb9-1 (P91) power engineering steel for pipes. The specimens machined from the as-received pipe were subjected to fatigue loadings and monitored simultaneously using DIC and ESPI techniques. It was found that DIC technique, although characterised by lower resolution, was more effective than ESPI. DIC allows to monitor the fatigue behaviour of steel specimens and accurately indicate the area of potential failure even within the initial stage of fatigue damage development.

Low-cycle fatigue damage accumulation near the cold-expanded hole by crack compliance data

Novel destructive method is implemented for quantitative assessment of fatigue damage accumulation in the stress concentration zone near the cold-expanded hole, which is characterized by residual stress influence. Damage accumulation is reached by preliminary push–pull loading of plane specimens with cold-expanded holes. Artificially introduced narrow notches, emanating from the hole edge at different stages of low-cycle fatigue, serve to manifest a damage level. Deformation response to local material removing is measured by electronic speckle pattern interferometry (ESPI) in terms of in-plane displacement components. Notches are inserted under constant external load to increase the measurement accuracy by reaching optimal fringe density. Normalized values of the notch mouth open displacement (NMOD), in-plane displacement component acting in the notch direction (U), the stress intensity factor (SIF), the T-stress and the biaxiality ratio are used as current damage indicator. Numerical integration of curves, describing an evolution of each fracture mechanics parameter, produces the damage accumulation function in an explicit form. It is established that all five fracture mechanics parameters give very close results. Developed approach is the essential link in predictable joints design to reach maximal beneficial effect of cold hole expansion on the fatigue life improvement of advanced aerospace structures.

Comparison Between Surface and Near-Surface Residual Stress Measurement Techniques Using a Standard Four-Point-Bend Specimen

BackgroundDetermination of near-surface residual stresses is challenging for the available measurement techniques due to their limitations. These are often either beyond reach or associated with significant uncertainties.ObjectiveThis study describes a critical comparison between three methods of surface and near-surface residual stress measurements, including x-ray diffraction (XRD) and two incremental central hole-drilling techniques one based on strain-gauge rosette and the other based on electronic speckle pattern interferometry (ESPI).MethodsThese measurements were performed on standard four-point-bend beams of steel loaded to known nominal stresses, according to the ASTM standard. These were to evaluate the sensitivity of different techniques to the variation in the nominal stress, and their associated uncertainties.ResultsThe XRD data showed very good correlations with the surface nominal stress, and with superb repeatability and small uncertainties. The results of the ESPI based hole-drilling technique were also in a good agreement with the XRD data and the expected nominal stress. However, those obtained by the strain gauge rosette based hole-drilling technique were not matching well with the data obtained by the other techniques nor with the nominal stress. This was found to be due to the generation of extensive compressive residual stress during surface preparation for strain gauge installation.ConclusionThe ESPI method is proven to be the most suitable hole-drilling technique for measuring near-surface residual stresses within distances close to the surface that are beyond the penetration depth of x-ray and below the resolution of the strain gauge rosette based hole-drilling method.

Analysis of the angular influence in the spatial study of mechanical displacements in highly anisotropic media

Tumors with anisotropy in their structural properties experience unpredictable and asymmetric growth along certain directions that can vary over time during the tumor progression. An early recognition of such anisotropy could provide information about their malignity, facilitating early diagnostics/prognostic. However, it is difficult to be observed by classic echography. Diverse studies of the literature show 3D images of elastic properties in media with anisotropy in a certain direction, but are transversely isotropic. However, for highly anisotropy media this assumption is no longer valid and requires specific measurements of shear velocities in the 3D directions. These media with 21 independent elastic material parameters and no symmetry plane. Techniques using ultrafast focused sound scanners present difficulties in covering immediate regions around the focused area and specific information for different incident beam orientations to obtain complete 3D spatial information, which is relevant in these types of media without planes of symmetry. It is the case of malignant tumors. The current paper presents a flexible spatial study of mechanical displacements induced in highly anisotropic soft media by low frequency shaker (including printed inorganic, pseudo-organic grids and cow fiber tissues respectively). Homogeneous and heterogeneous media without planes of symmetry have been tested in the experiments by using speckle ultrasonic interferometry. Velocities associated to the induced low frequency-mechanical displacements have been analyzed at a point of interest within the sample from different angles of propagation, covering a 3D angular space. These measurements show a high spatial-dependence of results, demonstrating the relevance of making spatial angular scans to derive parameters related to the anisotropy. This technique allows detection of anisotropies in small areas of analysis, even if they are weak.

Measuring guitar top plate resonances at stages of fabrication

This project investigates how the shape, quality, and boundary conditions of an object affect its normal modes of vibration. Here we report the results of electronic speckle pattern interferometry (ESPI) measurements on several potential guitar top plates in moving from a solid rectangle shape to the final top plate shape with a sound hole and bracing. The measured nodal patterns were similar for two distinct top plates as they were cut and sanded into final form. The measured frequencies of each normal mode were similar with typical variations of less than 10%. The experimental data was compared to theoretical data modeled in COMSOL to test the accuracy of the input parameters characterizing the wood. We found that the model results agree with the experimental data well at low frequencies, but the accuracy of the model decreases when higher frequency modes are considered.

Machine learning recognition of vibrational modes in ESPI data

We present a neural network (NN), constructed in Mathematica, that classifies images generated by electronic speckle pattern interferometry (ESPI). The goal of this project was to use the program to identify features in the images representing resonance behavior of the object. Much of our data was collected from unfinished wood surfaces, resulting in only the appearance of nodal lines in our ESPI data rather than the concentric rings that are hallmarks of data from finished instruments. The NN described here was trained to give four different output classifications: no resonant features, concentric ring patterns, clear nodal line patterns, and weak resonance features that correspond to ambiguous features observed at the high and low edges of the resonance band. The NN was trained using a collection of images from scans by an interferometer of multiple wood plates, an aluminium plate, and guitar top plates. In order to improve the accuracy of the classifier, we also explored image filtering techniques to increase the contrast of the images. This NN will eventually automate the process of finding resonant frequencies in real time when scanning new surfaces.

ConvNets for counting: Object detection of transient phenomena in steelpan drums

We train an object detector built from convolutional neural networks to count interference fringes in elliptical antinode regions in frames of high-speed video recordings of transient oscillations in Caribbean steelpan drums, illuminated by electronic speckle pattern interferometry (ESPI). The annotations provided by our model aim to contribute to the understanding of time-dependent behavior in such drums by tracking the development of sympathetic vibration modes. The system is trained on a dataset of crowdsourced human-annotated images obtained from the Zooniverse Steelpan Vibrations Project. Due to the small number of human-annotated images and the ambiguity of the annotation task, we also evaluate the model on a large corpus of synthetic images whereby the properties have been matched to the real images by style transfer using a Generative Adversarial Network. Applying the model to thousands of unlabeled video frames, we measure oscillations consistent with audio recordings of these drum strikes. One unanticipated result is that sympathetic oscillations of higher-octave notes significantly precede the rise in sound intensity of the corresponding second harmonic tones; the mechanism responsible for this remains unidentified. This paper primarily concerns the development of the predictive model; further exploration of the steelpan images and deeper physical insights await its further application.

Finite element modeling of guitar top plates

Here we describe the results of finite element method modeling of the resonant vibrations of a guitar top plate in various stages of construction using COMSOL. These models were completed in parallel with electronic speckle pattern interferometry ESPI measurements on three different top plates made of Engleman spruce purchased from Stewmac. The modeling was first set up for a thin piece of wood in a rectangular shape. Subsequent modeling was done at each step as the bode shape was cut, then a tone hold cut, and finally bracing was added. Care was taken to rotate the stiffness matrices for the braces in the model. Normal mode eigenfrequencies and mode shapes were calculated at each step in the fabrication process. Good agreement between the model and the measured data was obtained at low frequencies, but the model deviated from the measured results at higher frequencies.

Residual stress determination using full-field optical methods

Residual stresses are created in engineering components during fabrication and processing. Such stresses can strongly influence structural behavior. They are generally found by experimental means. A widely used way of finding residual stresses is removal of a small volume of material containing stresses and measurement of the strains that develop in surrounding material as a result of stresses being released. The strains can then be used to compute residual stresses. Drilling a small shallow hole is the most common way of implementing this approach, with strains measured by nearby strain gages adhered to the surface. This paper provides an overview of how full-field optical methods can be used instead of strain gages with hole drilling, overcoming limitations associated with gages and expanding capabilities of the hole drilling approach. The methods considered are holographic and electronic speckle pattern interferometry, Moire interferometry and digital image correlation. Advantages of using optical methods to find residual stresses are shown. A variety of applications is presented, ranging from determination of stresses in underground piping to stresses in microscale specimens. In addition, optical approaches employing different ways of material removal for stress release are reviewed, as well as several non-destructive optical methods for determining residual stresses.

Shape Measurement Method of Two-Dimensional Micro-Structures beyond the Diffraction Limit Based on Speckle Interferometry

A technique based on speckle interferometry for observing microstructures beyond the diffraction limit by detecting the spatial phase distribution of scattered light from microstructures has previously been reported. In this study, the development of this technique using a two-dimensional method is discussed. In order to observe general two-dimensional images, development of new technology in several stages is required. A two-dimensional filtering technique to reduce the noise component and a two-dimensional integration path to detect the three-dimensional shape of the surface are described in detail. As a first step toward observing complex two-dimensional structures in the future, it is investigated that directional two-dimensional information such as fibrous materials and micro-linear structures can be visually captured and treated as meaningful two-dimensional structures. As a result, it is shown that it is possible to observe fine two-dimensional letters with a line width of 100 nm, which is beyond the diffraction limit of the objective lens, demonstrating the effectiveness of the observation technique for microstructures by phase detection.

Corrigendum: The NASA High-Resolution Speckle Interferometric Imaging Program: Validation and Characterization of Exoplanets and Their Stellar Hosts

Corrigendum: The NASA High-Resolution Speckle Interferometric Imaging Program: Validation and Characterization of Exoplanets and Their Stellar Hosts

A joint occultation and speckle investigation of the binary star TYC 1947-290-1 and of the asteroid (87) Sylvia

ABSTRACT We report on the occultation of the star TYC 1947-290-1 by the asteroid (87) Sylvia. While asteroidal occultations occurring at fixed professional-level locations are relatively rare and are only recently starting to be observed with sufficiently high time resolution and sensitivity, they have the capability to measure sub-milliarcsecond angular diameters. The event described here was especially outstanding because the star was revealed to be a small-separation binary (≈10 mas at discovery), while at the same time the asteroid is not only one of the largest in size but it also has two satellite moons. The observations were carried out at the Russian 6-m telescope in 2019 December, and initially consisted of both a fast photometric series of the occultation itself, as well as of extensive speckle interferometry of the star and asteroid in the time immediately before and after the occultation. Subsequently, we obtained speckle data of TYC 1947-290-1 over a period of 1 yr after the event. We are able to present a detailed study of the binary star including measurements of the angular diameter of the stellar components, their geometry, and relative fluxes over several bandpasses, and to provide an accurate determination of the size of (87) Sylvia. We emphasize that we have been able to obtain the smallest ever directly measured stellar diameter, below the 100 micro-arcsecond level. Our data are also suitable for imaging of the asteroid by speckle holography, a task which we intend to carry out in a separate work.

Study of inhomogeneous fields of residual stresses using step-by-step enlarged crack method in combination with electronic speckle pattern interferometry (ESPI)

This article covers the development of methodological issues, software, experimental equipment, and practical application of the method of sequentially increasing cracks for studying inhomogeneous high-gradient fields of residual stresses (RS) that occur in areas of structural heterogeneity in flat construction parts (e.g., welded joints). Method of electronic speckle pattern interferometry (ESPI) is used to detect the deformation response in the form of the fields of displacement of the surface of the object under study arising from formation of successively increasing crack. ESPI provide contactless registration of movements directly in a digital form with high accuracy. The scheme of a specialized interferometer is described along with the features of the procedure for registering the displacement fields arising from a stepwise increase of the crack length. A return device provided removing of the object under study out of the optical zone and then return it to the initial position after performing the necessary mechanical operations. The accuracy of the procedure for calculating RS is estimated on the basis of mathematical processing of the experimentally obtained dependences of SIF on the crack length. An example of using the developed methods, equipment and programs for studying the RS distribution in stir welding joint of the sheets of aircraft alloy 1163T with a high level of crack resistance is given.

Speckle Interferometry of Nearby Multiple Stars. II. 2007–2020 Positional Measurements and Orbits of Sixteen Objects

Abstract Long-term monitoring at the 6 m telescope of the Special Astrophysical Observatory of the Russian Academy of Sciences made it possible to improve the orbits of 15 objects (HIP 689, HIP 3951, HIP 10438, HIP 43948, HIP 69962, HIP 95995, HIP 102029, HIP 102357, HIP 104383, HIP 105947, HIP 106255, HIP 108917, HIP 111546, HIP 113726, HIP 114922) and construct an orbital solution for HIP 65327 for the first time. Observations have been carried out since 2007; that is, the accumulated data correspond to an interval of 13 yr. As a result, most of the orbits were classified as “accurate” using the qualitative criteria by Worley & Heintz. A comparison of the mass sums and masses of the components calculated by two independent methods was made for objects with orbital solutions. The Gaia EDR3 parallax was used to obtain the fundamental parameters, as well as the Hipparcos and Gaia DR2 parallaxes.

Twin High-Resolution, High-Speed Imagers for the Gemini Telescopes: Instrument Description and Science Verification Results

Two new imaging instruments, ‘Alopeke and Zorro, were designed, built, and commissioned at the Gemini-North and Gemini-South telescopes in 2018 and 2019, respectively. Here we describe them and present the results from over a year of operation. The two identical instruments are based on the legacy of the DSSI (Differential Speckle Survey Instrument) instrument, successfully used for years at the WIYN and the Gemini telescopes in Hawaii and Chile. ‘Alopeke and Zorro are dual-channel imagers having both speckle (6.7″) and “wide-field” (∼1 arcminute) field-of-view options. They were built to primarily perform speckle interferometry providing diffraction-limited imagery at optical wavebands, yielding pixel scale uncertainties of ±0.21 mas, position angle uncertainties of ±0.7◦, and photometric uncertainties of Δm ± 0.02–0.04 magnitudes (for the blue and red channels, respectively) when run through the standard data reduction pipeline. One of their main scientific roles is the validation and characterization of exoplanets and their host stars as discovered by transit surveys such as the NASA Kepler, K2, and TESS missions. The limiting magnitude for speckle observations at Gemini can be quite faint (r ∼18 in good observing conditions) but typically the observed targets are brighter. The instruments can also function as conventional CCD imagers providing a 1 arc-minute field of view and allowing simultaneous two-color, high-speed time-series operation. These resident visitor instruments are remotely operable and are available for use by the community via the peer-reviewed proposal process.

Экспериментальное определение вибрационных характеристик рабочих лопаток турбин помехоустойчивым цифровым спекл-интерферометром

The paper notes the wide possibilities and high efficiency of vibration diagnostics of parts and assemblies of power units by the method of electronic speckle interferometry (ESI), shows the feasibility of developing and improving methods for obtaining speckle interferograms of vibrating objects. A patented by the authors' scheme of a digital speckle interferometer (DSI) for determining the dynamic parameters of products is presented. The diffuse reference wave greatly simplifies its alignment, mainly the aligned channels of propagation of interfering beams determine the resistance to mechanical and thermal disturbances, and the separate beam splitter and diffuser make it easy to optimize the optical scheme for the object under study. Speckle interferograms are obtained by speckle correlation methods and a developed method for determining the contrast of the dynamic speckle pattern. It does not impose special requirements on the parameters of the video system, does not require the use of a specialized video camera, and allows, by using a rotary platform, to organize a panoramic view of the oscillatory forms of asymmetric structures. The use of this method in combination with the proposed optical scheme provides an express analysis of products in off-bench conditions. The increased noise immunity of the installation allows the determination of the spectrum of frequencies and vibration modes (SFVM) of samples under free boundary conditions, which is rarely realized in interferometry. The paper presents examples of such speckle interferograms, the expediency of obtaining which is important in the resonance study of the elastic properties of the material and vibration resonance flaw detection. The implemented software and hardware solutions increase the resolution and visibility of the band patterns; facilitate their quantitative interpretation and the extraction of numerical information on the distribution of vibration amplitudes. The area of scientific interests and the specificity of the author's developments have determined the preferential adaptation of the proposed device with a complex of software and methodological developments for vibration testing of gas turbine engine (GTE) blades.

Damage evolution in sandwich components at different extreme temperatures

Composites' structures are subjected to various environmental conditions during their service life. However, only a few papers are focalized on analysing damage history after impact at shallow temperatures and among them, even less concern sandwich components. Futhermore, since the effect of any degradation phenomena may not be visible to the naked eye, the evolution of the damage is followed with non-destructive techniquest. In this paper, the damage suffered by sandwich structure composites was evaluated by three NDT techniques: Ultrasound, Lock-in Thermography and speckle interferometry. Sandwich structures investigated consist of carbon fibre reinforced face sheets surrounding a PVC core. Indentation and penetration tests (U = 7.5J, 10.5 J and 12 J) were carried out at room temperature and −55°C, +70°C. After tests, damage extension and propagation has been evaluated in terms of indentation depth and delamination by NDT. The results provided useful information about the influence of extreme temperature on both impact properties and damage evolution in the system investigated.

Determining Residual Stresses in Weld Joints of DN 850 Pipes by Spot Drilling Combined with Electronic Speckle Pattern Interferometry

Residual welding stresses affect significantly the strength, durability, and performance of structures. Therefore, there is an urgent need for developing and implementing techniques and equipment that allow reliably estimating stresses in experiments. This paper considers some aspects of the joint implementation of electronic speckle pattern interferometry and the spot drilling technique to determine these characteristics under the field conditions. The results of determining the distribution of residual stresses in the weld joint areas of DN 850 pipes are given for various welding modes. The study results are of independent significance and herewith, demonstrate the efficiency of the equipment developed to solve similar problems.

Use of laser speckle shearing interferometric vibration measurement system for acoustic-to-seismic landmine detection

To study the application of laser shearing speckle interferometric vibration measurement technology in acoustic resonance landmine detection, we present an experimental and theoretical study of the method for laser shearing speckle interferometric landmine detection based on time-average. The relationship between the out-of-plane displacement gradient generated by the sound wave on the ground and the phase change of the shearing interference laser is analyzed. A high-power loudspeaker is used as the source of sound wave excitation, and the laser shearing speckle interferometric vibration measurement system is used in landmine detection experiments to investigate the changes of laser shearing speckle interference fringes under different experimental conditions such as sound wave intensity, detection target, buried depth, and soil environment. The study reveals that it is feasible and effective to use laser shearing speckle interferometry to detect landmines, and it provides a theoretical and methodological basis for realizing the rapid scanning of acoustic-optic landmine detection.

Phase singularity reduction in speckle interferometry by tailoring the spatial coherence of light.

Reducing the number of phase singularities in speckle interferometry by physical means increases the quality of the phase deconvolution and enhances the separability of fringe systems, especially for highly dynamic fringe systems. The reduction is achieved by tailoring the spatial coherence of the light source at the entrance of the interferometer. The reduction mechanism is non-intuitive and rests on a change of size and of position of the speckle patterns as a result of the spatially shaped coherence. After demonstrating the amount of reduction that may be achieved, the reduction mechanism is explained theoretically and via simulations, and it is vindicated in an experiment using a Michelson-Mach-Zehnder interferometer hybrid.