Significant Differences In Strength Research Articles

Comparison of wrist range of motion and muscle strength in assembly workers with and without lateral epicondylitis.

Lateral epicondylitis (LE), also called tennis elbow, is a common musculoskeletal disorder that causes pain in the elbow area and is highly prevalent in assembly workers who repeatedly move their wrists. The purpose of this study was to compare the wrist ROM and muscle strength of assembly workers with and without LE. Forty-five male assembly line workers (23 with LE) participated in the study. Participants had their wrist range of motion (flexion, extension, ulnar deviation, and radial deviation) and strength (wrist flexors, extensors, and hand grip) measured using Smart KEMA sensors. Workers with LE showed significantly reduced wrist extension and radial deviation ROM compared to workers without LE, with no significant differences in wrist flexion and ulnar deviation ROM between groups. Workers with LE had significantly lower wrist extensor strength compared to workers without LE, and there was no significant difference in wrist flexor and grip strength between the two groups. For workers with LE, the difference in wrist ROM and muscle strength will be useful for planning intervention and evaluating treatment outcomes for assembly workers with LE.

Isokinetic strength testing with different biomechanical demands on core strength: a comparison of military competitive athletes and soldiers with high occupational physical strain

It is known that anthropometric data (weight, height, BMI, waist circumference and WHtR) and male gender are positively correlated with greater core strength, while age is negatively correlated. For competitive athletes with no significant differences in the anthropometric data stated above, there have hardly been any studies in which isometric core strength in a seated position is quantitatively compared among athletes in different sports. This study aimed to analyse different sports in well-trained athletes using military competitive sports as an example with regard to possible differences in core strength. For this purpose, Parachuting (n=28), Military Pentathlon (n=34) and Ski Platoon (n=38) groups were compared with regard to isokinetic core strength using dynamometry in seated position. In addition to the comparison of anthropometry and isokinetic results with descriptive statistics, ANOVA and Welch-ANOVA were used to compare the means of absolute and weight-adjusted core strength. It was shown that the Ski Platoon group had significantly higher flexion peak torque values than the Military Pentathlon and Parachuting groups. Even when adjusted for weight, the values were significantly higher than those measured in the Military Pentathlon group but not significantly higher than those in the Parachuting group. For extension peak torque, it was found that the Military Pentathlon group had significantly lower values than the Ski Platoon group and, in the weight-adjusted analysis, significantly lower values than the Parachuters. Using the example of competitive military sports, this study was able to show that there are significant differences in isokinetic core strength even among professional competitive athletes.This knowledge should be used to carry out detailed quantitative analyses of core strength, even in well-trained professional athletes, to find applications for prevention or to coordinate compensating exercises.

Delayed Onset Muscle Soreness Following Acute Resistance Exercise in Untrained Females: A Comparative Study Between Vegans and Omnivores.

This study aimed to assess the levels of delayed onset muscle soreness (DOMS) markers in individuals adhering to vegan and omnivore diets after engaging in acute resistance exercise. A total of 54 untrained young, healthy, normal-body-weight women (age: 26.8±4.1 years; body mass index: 22.5±2.7 kg/m2) participated in the study. Participants were categorized into two groups: vegans (n=27) and omnivores (n=27) based on their dietary preferences, with all subjects having adhered to their respective diets for a minimum of 2 years. DOMS was induced by a single eccentric resistance exercise session, comprising four exercises (leg press, chest press, leg curls, and arm curls), each consisting of four sets of 10 repetitions. Various measurements, including dietary factors, state of wellness, body composition, muscle circumferences, muscle pressure point thresholds (PPTs), and muscle strength, were recorded both before and 48 hours after the exercise session. The results showed that wellness and muscle circumferences remained unchanged or displayed similar changes between the vegan and omnivore groups following acute resistance exercise. However, notable differences were observed in PPTs in favor of vegans, specifically for the right biceps (95% CI: 1.4 to 10.2; p=0.01), the left vastus medialis (95% CI: 0.5 to 6.4; p=0.02), and the right vastus lateralis (95% CI: 3.2 to 12.1; p=0.001). Furthermore, significant differences in right grip strength were found in favor of vegans after the exercise session (95% CI: 3.1 to 26.2; p=0.01). In conclusion, our findings suggest that vegans may experience more favorable changes in DOMS levels following acute resistance exercise in comparison to omnivores. This discrepancy in DOMS markers may indicate enhanced muscle recovery in vegans.

Immediate effect of different herbal solutions on tensile strength of suture materials in oral cavity

This pilot study evaluated the immediate effect of different herbal solutions in oral use on the tensile strength of the sutures used in oral surgical procedures. Three frequently used suture materials, polyglactin 910 (PGA), poliglecaprone (PGCL), and polypropylene (PP), were chosen in a 4-0-gauge size. The sutures' tensile stress was evaluated before being immersed (baseline) and after immersion at 24 h, 1 week, and 2 weeks in four different media: artificial saliva, chlorhexidine, Commiphora myrrh, and frankincense. The tensile strength was assessed by applying a 50 N load at a standardized speed of 2 mm/min. The data were analyzed using one-way and three-way analysis of variance (ANOVA) and the Tukey post hoc test with a significance level of p ≤ 0.05 significance level. The mean values of the maximum load showed a significant statistical difference across the three types of sutures (PGA, PGCL, and PP). The mean tensile strength of the PP suture was statistically lower than that of the other sutures. There was a statistically significant difference in the mean tensile strength of the PGA suture when stored in chlorohexidine media and the PGCL suture for frankincense media. The tensile strength for all sutures was the lowest value when immersed in Commiphora myrrh media. Home-prepared herbal solutions can affect the tensile strength and maximum load of suture materials. Careful and controlled use of herbal solutions after any dental surgical procedures is advisable.

Differences of compressive strength between calcium carbonate from blood clam shells and calcium hydroxide as a candidate for pulp capping material

Background: Pulp capping is one of the treatments for reversible pulpitis and aims to maintain pulp vitality. This treatment requires a material that can protect the pulp with good biocompatibility. The physical and mechanical properties, bio interactivity and bioactivity of pulp capping materials are very important for the formation of reparative dentin. Calcium hydroxide (Ca(OH)2) as the gold standard material in pulp capping treatment also has some disadvantages. Another alternative for pulp capping material is blood clam shell because it contains 98% calcium carbonate (CaCO3), which is a compound with a bone-like structure and can induce pulp cell differentiation. Objective: To investigate and explain the difference in compressive strength between CaCO3 from blood clam shells and Ca(OH)2 as a candidate pulp capping material. Methods: This research is a laboratory experimental study with post test only control group design method. Ca(OH)2 and CaCO3 samples were formed with a mixture of powder and aquadest with 4x6 mm sample size. The samples were dried at room temperature and the compressive strength was measured using a universal testing machine (UTM). Result: There is a significant difference in compressive strength between Ca(OH)2 and CaCO3 blood clam shells in the Mann-Whitney test results (p<0.05). Conclusion: The results of the compressive strength test between the mixture of Ca(OH)2 with aquadest in a ratio of 1:1 are greater than the mixture of CaCO3 blood clam shells with aquadest in a ratio of 3:1 so that pure CaCO3 blood clam shells with distilled water without other additives cannot be used as a candidate for capping pulp material.

The Influence of Hip-Strengthening Program on Patients with Chronic Ankle Instability.

Background and Objectives: Repetitive ankle sprains lead to mechanical instability of the ankle. Patients with chronic ankle instability may experience decreased muscle strength and limited postural control. This study investigated the effects of a hip-strengthening exercise program on muscle strength, balance, and function in patients with chronic ankle instability. Materials and Methods: A total of 30 patients participated in the study and were randomly assigned to the two groups. Among the 30 participants, 14 were assigned to the hip joint-strengthening exercise group and 16 to the control group. The experimental group underwent a hip-strengthening exercise program and received training for 40 min per session twice a week for four weeks. The control group received the same frequency, duration, and number of sessions. Measurements were performed before and after the training period to assess changes in hip strength, balance, and function. Results: In the within-group and between-group comparisons, both groups showed significant differences in hip joint strength, static balance, dynamic balance, and function (FAAM; foot and ankle ability measures) (p < 0.05). Statistically significant differences were observed in the time × group interaction effects among the hip abductors and external rotation in hip joint strength, path length in static balance, posterolateral and posteromedial in dynamic balance, and FAAM-ADL and FAAM-SPORT functions (p < 0.05). Conclusions: Accordingly, this study confirmed that hip joint-strengthening exercises have a positive effect on the strength, balance, and function of patients with chronic ankle instability, and we believe that hip joint-strengthening exercises will be recommended as an effective intervention method for patients suffering from chronic ankle instability.

A 3 month nutrition and exercise program improved hallux strength among senior daycare center users in Korea: a cluster randomized controlled trial.

With a growing aging population, the focus on the health and well-being of older adults, especially in preventing falls, becomes crucial. This 3 month study, initiated in July 2022, aimed to assess the impact of a nutrition and exercise program in senior daycare centers in Chuncheon, South Korea. A 3 month study, beginning in July 2022, included 204 older adults from 10 senior daycare centers in Chuncheon, South Korea. Randomly assigned to intervention or control groups, the intervention involved nutrition, daily toe exercises, or both. Control centers received interventions post-measurements. Pre- and post-intervention analyses used paired t-tests and multiple linear regression, assessing metrics like toe grip strength for significance. While 204 were initially enrolled, the analysis included 151 participants due to dropouts. Participants, with a mean age of 83.3 years (43.1% aged ≥ 85 years), exhibited mild to moderate cognitive impairment and multiple chronic illnesses. Health data indicated that 37.3% were obese, and the average BMI was 24.0 kg/m2. Both the intervention and control groups showed significant improvements in toe grip strength post-intervention. Specifically, the exercise-only and combined exercise-nutrition groups demonstrated significant differences in hallux strength compared to the control group after adjusting for age and gender. The study showed that a basic nutrition and exercise program increased toe strength in older adults with chronic diseases, including mild cognitive impairments. This intervention holds potential to prevent muscle strength decline and reduce fall risks in older individuals. As the first of its kind in Korean senior daycare centers, it emphasizes the need for future research and standardized programs for senior daycare users.

Shear Bond Strength of Clear Aligner Attachment Using 4-META/MMA-TBB Resin Cement on Glazed Monolithic Zirconia.

Increasing demand for adult orthodontic treatment using clear aligners has highlighted challenges in bonding clear aligner attachments to various restorations. Specifically, the bond strength of clear aligner attachments to glazed monolithic zirconia has not been extensively studied. This study aims to compare the shear bond strength (SBS) and mode of failure (MOF) of conventional bonding methods versus Superbond C&B (4-META/MMA-TBB resin cement) for clear aligner attachments on glazed monolithic zirconia. Fifty sintered and glazed zirconia samples were divided into five groups and attached with clear aligner attachments: Si (silane), B (bonding agent), SiB (bonding agent and silane), SU (Superbond C&B), and SiSU (silane and Superbond C&B). SBS and MOF of these samples were analyzed. Results indicated a significant difference in bond strength among the groups. SiSU exhibited the highest bond strength, followed by SU, while B had the lowest bond strength. SEM analysis revealed that SiSU and SU predominantly exhibited mixed failure, indicating high bond strength without affecting the glazed layers of the zirconia. In contrast, B exhibited only adhesive failure at the interface, resulting in insufficient bond strength for effective orthodontic treatment. In conclusion, using 4-META/MMA-TBB resin cement provides high bond strength for clear aligner attachments on glazed zirconia with minimal material damage during debonding.

Sequential Comparison of Knee Muscle Strength after Anterior Cruciate Ligament Reconstruction between Hamstring Autograft and Tibialis Anterior Allograft: Propensity Score Matched Pair Analysis.

Among the graft options for anterior cruciate ligament reconstruction (ACLR), hamstring autografts are widely regarded as the preferred choice for primary ACLR among orthopedic surgeons worldwide. However, concerns persist regarding postoperative knee flexor weakness. We aimed to compare knee extensor and flexor strengths between hamstring autograft and tibialis anterior allograft groups in ACLR patients, who were propensity score-matched based on baseline characteristics. A retrospective analysis included 58 matched pairs who underwent isokinetic strength tests at 6 and 12 months post operation. Isokinetic muscle strength tests found no significant difference in knee extensor and flexor strength at 6 months post operation between the hamstring autograft and tibial anterior allograft groups. At 12 months, the hamstring autograft group exhibited significantly greater knee flexor deficit (total work and average power) compared to the allograft group, despite no differences in extensor strength or patient-reported outcomes. This study highlights the impact of hamstring autograft harvesting on muscle strength and recovery following ACLR in short-term period.

The relation between mental health and career-related stress among prospective graduates in higher education stage during the COVID-19 pandemic: an evidence based on network analysis.

The outbreak of the COVID-19 pandemic has disrupted people's routine, bringing uncertainty and stress, leading to mental health issues. This situation is particularly acute among Chinese prospective graduates in higher education stage as they cannot predict the outcomes of their studies, graduation, and career development, and therefore experience career-related stress. This study included 4041 prospective graduates in higher education stage (using handy sampling) recruited in March 2020 as participants (M Age = 22.56, SD = 1.865), utilizing a Sparse Gaussian Graphical Model for regularized partial correlation network analysis of depression symptoms (by PHQ-9), anxiety symptoms (by GAD-7), and career-related stress, which aims to explore the role of career-related stress in the symptom networks of depression and anxiety among prospective graduates in their final semester. The results revealed that fatigue, sad mood, and psychomotor symptoms in depression, as well as uncontrollable worry and trouble relaxing in anxiety, were central symptoms in the network. Additionally, sad mood and guilt belonging to depressive symptoms, and feeling afraid, restlessness, and irritability belonging to anxiety symptoms, served as bridge symptoms connecting symptom communities. Specifically, guilt as a depressive symptom showed a strong association with employment stress in career-related stress. There were no significant differences in network structure and global strength based on participants' gender. However, despite no significant differences in network structure, the global strength of prospective graduates from Wuhan was significantly lower than samples from non-Hubei provinces, possibly indicative of a Typhoon Eye Effect. The findings of this study can inspire psychological professionals in higher education institutions to provide support for mental interventions and therapies for prospective graduates, and addressing career development issues.

Shear bond strength and adhesive remnant index evaluation of three different orthodontic adhesive systems using three different light curing times

BackgroundSuccess of long orthodontic treatment using orthodontic brackets depends mainly on the efficiency of the adhesive system used and it's degree of resistance in the face of stresses and foresees applied during treatment. The aim of this study was to evaluate the shear bond strength of orthodontic brackets bonded with three adhesive systems using different light curing times. Materials and methodsThe 126 human extracted premolars were randomly divided into three equal groups (n = 42) depending on the type of adhesive system used; total-etch (Transbond XT), self-etch (Transbond Plus), and self-adhesive (GC-Ortho Connect) system. Then each group was randomly subdivided into three subgroups (n = 14) based on the curing time; 1-s, 3-s, and 20-s. The shear bond strength (SBS) and adhesive remnant index (ARI) were evaluated in each subgroup using universal testing machine and stereomicroscope respectively. The data were analyzed statistically by a two-way ANOVA for SBS, and Scheirer Ray Hare Test for ARI. The significance level was set at P ≤ 0.05. ResultsThe results showed a statistically significant difference in shear bond strength at the three-time points for each adhesive system (p < 0.001) with the highest SBS value in 20-sec groups followed by 3-sec groups while 1-sec groups was the lowest. However, there was no statistically significant difference in Shear bond strength between the three adhesive systems except 20-sec groups (p < 0.001). ARI showed a statistically significant difference between all adhesive systems with the highest scores in TE groups, while the lowest in SE groups. ConclusionAll adhesive systems provided acceptable values of SBS at all curing times except the 1-sec group in SE and SA adhesive systems where the SBS values were the lowest and below the acceptable range.

Ultrasound-guided gluteal nerves electrical stimulation to enhance strength and power in individuals with chronic knee pain: a randomized controlled pilot trial.

Various pathophysiological contexts can be accompanied by weakness, arthrogenic muscle inhibition, and even disability. In this scenario, peripheral nerve stimulation has been studied not only for pain management but also for the improvement of neuromuscular parameters. For this purpose, the use of Transcutaneous Electrical Nerve Stimulation (TENS) has typically been investigated, but recently, the use of ultrasound-guided percutaneous peripheral nerve stimulation (pPNS) has gained popularity. In this regard, electrical stimulation has a predisposition to activate Type II muscle fibers and has been shown to be capable of generating short-term potentiation by increasing calcium sensitivity. However, the evidence of pPNS applied in humans investigating such variables is rather limited. This pilot study aimed to assess the feasibility of the methodology and explore the potential of pPNS in enhancing hip extension performance in individuals suffering from knee pain, comparing it with TENS. Twelve participants were divided into pPNS and TENS groups, undergoing pre- and post-intervention assessments of peak concentric power (W), strength (N), execution speed (m/s), and one-repetition maximum (1RM) (kg) estimation. For pPNS, two needles were positioned adjacent to the superior and inferior gluteal nerves under ultrasound guidance. For TENS, electrodes were positioned between the posterosuperior iliac spine and the ischial tuberosity, and halfway between the posterosuperior iliac spine and the greater trochanter. The interventions consisted of 10 stimulations of 10 s at a frequency of 10 Hz with a pulse width of 240 μs, with rest intervals of 10 s between stimulations. Peripheral nerve stimulation significantly improved concentric power at 30% (p = 0.03) and 50% (p = 0.03) of 1RM, surpassing TENS, which showed minimal changes. No significant strength differences were observed post-intervention in either group. This work presents evidence where pPNS applied to the gluteal nerves results in an enhanced performance of hip extension at submaximal loads. However, this improvement does not seem to be reflected in short-term changes in the estimation of the 1RM by the force-velocity profile.

Effect of the percentage of MUF adhesive coverage on shear strength when bonding different wood species

Due to climate changes, it is necessary to consider the use of other wood species to replace currently used woods. This work deals with the determination of the shear strength of bonded veneers (eight European wood species: spruce, larch, pine, beech, oak, poplar, birch, and alder) with Silekol® 311 melamine-urea-formaldehyde adhesive (MUF) with a variable coverage on the surface of the samples: 10, 15, 20, 25, 30, 50, 75, and 100%. The Automated Bonding Evaluation System (ABES) was used to evaluate and compare adhesive bond strengths. The larch, beech, and oak samples exhibited greater single-lap shear strength than the control samples from spruce. There was no statistically significant difference in shear strength regarding the adhesive coverage from 100% to 20% on the surface of the samples, for almost all wood species. The results of the project provide basic information about the bonding strengths with different coverage in the adhesive layer, comparing non-commonly used wood species in wood-based composites such as oriented strand board and particleboard.

Is There a Relationship Between Grip Strength and Injuries in Professional Baseball Players?

Injuries in professional baseball players have become exceedingly common. Efforts to mitigate injury risk have focused on the kinetic chain, shoulder motion, and so forth. It is unclear whether grip strength is related to injury risk in professional baseball pitchers. The purpose of this study was to determine if grip strength was a risk factor for injury. It was hypothesized that pitchers with weaker grip strength would have a higher likelihood of sustaining a shoulder or elbow injury compared with pitchers with stronger grip strength. Case-control study; Level of evidence, 3. All professional pitchers from a single Major League Baseball organization were included. Dominant and nondominant grip strength were measured after each pitching outing throughout the 2022 season. Injuries over the course of the season were recorded, and data were compared between pitchers who sustained a shoulder or elbow injury and those who did not. Overall, 213 pitchers were included, of whom 53 (24.9%) sustained a shoulder or elbow injury during the season. The mean grip strength for all pitchers was 144.0 ± 20.8 lb (65.3 ± 9.4 kg). The mean dominant-arm grip strength was 142.6 ± 20.8 lb (64.7 ± 9.4 kg) for pitchers who did not sustain a shoulder or elbow injury and 148.2 ± 20.9 lb (67.2 ± 9.5 kg) for pitchers who did sustain an injury, with no significant group difference in grip strength (P > .05). Furthermore, there were no significant differences in change in grip strength over the course of the season between the groups. There was no significant difference in mean grip strength or change in grip strength over the course of a single season between professional baseball pitchers who sustained a shoulder or elbow injury and those who did not.

Effect of Instrument Lubricant on Mechanical Properties of Restorative Composite.

Using a wetting resin or adhesive system as an instrument lubricant when placing composite layers is commonly practiced to improve handling. This study investigated whether instrument lubricants affected strength, stiffness, or hardness. Composite beams (TPH Spectra) were fabricated using a stainless steel mold (25×2.5×2 mm) in two steps, where the second half (12.5 mm) was added and cured against a cured first half (n=15). The composite surface at the open end of the first half was smoothed using an instrument lubricated with wetting resin (Ultradent) or universal adhesive (ScotchBond Universal), enough to prevent sticking, or without lubrication. An additional beam of each group was characterized using scanning electron microscopy. Monolithic specimens were also fabricated. After 24 hour storage (37°C, 100% humidity), the beams' flexural strength and stiffness were determined by four-point bending. Vickers surface hardness was measured on 24-hour composite samples in 2 mm deep acrylic cavities, cured after the surface was smoothed with the two instrument lubricants or no lubricant (n=10). Hardness was remeasured after finishing with a series of contouring and polishing discs. Data were statistically analyzed using ANOVA followed by Student-Newman-Keuls post hoc test at 0.05 significance level. There were significant differences (p<0.001) in flexural strength and stiffness among groups. While strength and stiffness were not affected by using a wetting resin as instrument lubricant, use of a universal adhesive increased strength and stiffness significantly, achieving monolithic values. Scanning electron micrographs showed less porosities at the interface when using instrument lubricants. Surface hardness was significantly reduced in groups in which instrument lubricants were used, but finishing/polishing restored original hardness (p<0.001). Lubricating an instrument with a wetting agent did not adversely affect physical or surface properties, provided the surface was finished and polished. If a universal adhesive was used as lubricant, the strength and stiffness of a layered composite could be increased, reaching monolithic values.

Compressive Strengths of Cube vs. Cored Specimens of Cement Stabilized Rammed Earth Compared with ANOVA

Cement-stabilized rammed earth (CSRE) is a variation of the traditional rammed earth building material, which has been used since ancient times, strengthened by the addition of a stabilizer in the form of Portland cement. This article compares the compressive strength of CSRE determined from specimens cored from structural walls and those molded in the laboratory. Both types of specimens underwent a 120-day curing period. The tests were conducted on specimens with various grain sizes and cement content. An analysis of variance (ANOVA) was performed on the obtained results to determine whether it is possible to establish a conversion factor between the compressive strength values obtained from laboratory-molded cubic samples and those from cored samples extracted from the CSRE structure. The study revealed that the compressive strength of CSRE increases significantly over the curing period, with substantial strength gains observed up to 120 days. The results indicated no statistically significant difference in the mean unconfined compressive strength (UCS) between cubic and cored specimens for certain mixtures, suggesting that a shape coefficient factor may not be necessary for calculating CSRE compressive strength in laboratory settings. However, for other mixtures, normal distribution was not confirmed. These findings have implications for the standardization and practical application of CSRE in construction, highlighting the need for longer curing periods to achieve optimal strength and the potential to simplify testing protocols.

The Effect of Carbamide Peroxide Bleaching Gel with and without Remineralizing Agents on Microtensile Bond Strength of Resin Composites to Enamel

Introduction: Carbamide peroxide bleaching gel, along with remineralizing agents, can induce changes in the structure and mineral content of enamel, potentially leading to a decrease in the bond strength of resin composite to the enamel. Therefore, this laboratory study aimed to determine the effect of carbamide peroxide bleaching gel with and without remineralizing agents on the microtensile bond strength (µTBS) of resin composites with microhybrid and nanofill structures to enamel. Materials and Methods: Thirty extracted third molar teeth were randomly divided into five groups, each group subdivided into two equal subgroups: Group 1: Control group, Group 2: Bleaching gel without fluoride, Group 3: Bleaching gel containing fluoride, Group 4: Bleaching gel containing CPP-ACP, and Group 5: Bleaching gel containing fluoride and CPP-ACP. In the first subgroups, nanofilled resin composite Filtek Z350, while in the second subgroups, microhybrid resin composite Filtek Z250 were bonded to enamel surface. After specimen preparation, µTBS was measured using a universal testing machine. Data were analyzed using parametric tests (P value&lt;0.05). Results: The highest µTBS of resin composite to enamel was observed in the control group, while the lowest bond strength was seen in the fluoride-containing bleaching group. Comparisons of µTBS between the study groups pairwise, except for the comparison between the control group and the bleaching group, the bleaching group with (CPP-ACP+Fluoride), and the (CPP-ACP) group with the fluoride group, showed significant differences in bond strength. Although, the mean µTBS of the Filtek Z250 composite was higher than the Filtek Z350 composite in all groups, but this difference was not statistically significant. Conclusion: The use of carbamide peroxide bleaching gel with remineralizing agents leads to a decrease in µTBS of the resin composite to the enamel.

Effects of Magnesium in Physiotherapy Treatment for Patients with Knee Osteoarthritis

Background: Osteoarthritis (OA) is a complex joint degenerative disorder. Pain is a dominant characteristic, becoming persistent and more limiting as the disease progresses, resulting in reduced physical function, quality-of-life. Magnesium deficiency is considered to be a major risk factor for osteoarthritis development and progression. Oral magnesium presents unique challenges for many individuals to effectively restore intracellular magnesium levels. Transdermal magnesium absorption could be more effective than oral absorption due to its greater absorption rate and presents fewer negative effects due to its gastrointestinal tract-bypassing nature. Method: Total 40 subjects with knee osteoarthritis were selected as per the inclusion and exclusion criteria and randomly assigned to either Group A (intervention) or Group B (conventional), each having 20 patients. Assessment of the outcome measures was done pre and post 8 sessions. Outcome measures used were Visual Analogue Scale (VAS), Western Ontario and McMaster Universities Arthritis Index (WOMAC), Timed up and go test (TUG), 9 Step stair climb test, Knee ROM, Quadriceps strength using pressure biofeedback. Group A was given conventional therapy along with Epsom salt foot soak and Magnesium oil application. Group B was given conventional therapy alone. Result: There was statistically significant improvement seen in all the outcome measures in intragroup analysis with p&lt;0.05. Intergroup analysis showed statistically significant difference in VAS on activity, WOMAC, Knee ROM, Quadriceps strength with p &lt;0.05 indicating Group A performed better than Group B. Conclusion: The study found that Magnesium when used as an adjunct to conventional therapy shows significant difference in pain levels, knee mobility, quadriceps strength and better functionality in activities of daily living. KEYWORDS: Knee osteoarthritis, Epsom salt, Magnesium, Physiotherapy.

The surface charge of electroactive materials governs cell behaviour through its effect on protein deposition

The precise mechanisms underlying the cellular response to static electric cues remain unclear, limiting the design and development of biomaterials that utilize this parameter to enhance specific biological behaviours. To gather information on this matter we have explored the interaction of collagen type-I, the most abundant mammalian extracellular protein, with poly(vinylidene fluoride) (PVDF), an electroactive polymer with great potential for tissue engineering applications. Our results reveal significant differences in collagen affinity, conformation, and interaction strength depending on the electric charge of the PVDF surface, which subsequently affects the behaviour of mesenchymal stem cells seeded on them. These findings highlight the importance of surface charge in the establishment of the material–protein interface and ultimately in the biological response to the material. Statement of significanceThe development of new tissue engineering strategies relies heavily on the understanding of how biomaterials interact with biological tissues. Although several factors drive this process and their driving principles have been identified, the relevance and mechanism by which the surface potential influences cell behaviour is still unknown. In our study, we investigate the interaction between collagen, the most abundant component of the extracellular matrix, and poly(vinylidene fluoride) with varying surface charges. Our findings reveal substantial variations in the binding forces, structure and adhesion of collagen on the different surfaces, which collectively explain the differential cellular responses. By exposing these differences, our research fills a critical knowledge gap and paves the way for innovations in material design for advanced tissue regeneration strategies.

Clinical and Radiological Outcomes of Medial Meniscal Allograft Transplantation Combined With Realignment Surgery.

The outcomes of medial meniscal allograft transplantation (MMAT) combined with high tibial osteotomy (HTO) compared with isolated MMAT remain unclear. To compare the clinical and radiological results of MMAT combined with HTO and isolated MMAT. Cohort study; Level of evidence, 3. This retrospective study included 42 consecutive patients, who were divided into group M (isolated MMAT; n = 22) and group H (MMAT combined with HTO with a varus angle >3°; n = 20). Group differences in subjective knee scores, isokinetic muscle strength test, and radiological outcomes (Kellgren-Lawrence grade, mechanical axis, graft extrusion, graft status, and articular cartilage loss) were compared. The mean follow-up period was 29.2 ± 4.9 months and 27.4 ± 5.3 months for groups M and H, respectively. The Lysholm score improved from 55.4 ± 9.5 to 81.3 ± 9.7 and from 52.6 ± 8.9 to 84.2 ± 10.2 in groups M and H, respectively (both P < .001). The International Knee Documentation Committee subjective score improved from 51.4 ± 10.3 to 79.6 ± 9.4 and from 49.3 ± 11.4 to 81.4 ± 8.3 in groups M and H, respectively (both P < .001). Both groups showed no significant differences in subjective knee scores and isokinetic extensor strength at the final follow-up. The rate of preoperative and postoperative high International Cartilage Regeneration & Joint Preservation Society grade (≥3) did not differ between the 2 groups. Group M showed greater coronal graft extrusion than did group H (3.3 ± 0.7 mm vs 2.7 ± 0.8 mm; P = .014); the rate of pathologic graft extrusion (≥3 mm) was not higher in group M (40.9%) than in group H (20%) with the number of patients available (P = .143). Both groups showed no significant difference in the graft status. Graft tears were observed in 2 patients (9%) in group M and 1 patient (5%) in group H (P = .607). Clinical scores significantly improved after isolated MMAT and MMAT combined with HTO compared with preoperative values, and their short-term outcomes were similar. Postoperative graft extrusion was greater in patients who underwent isolated MMAT, implying that active correction of varus alignment during MMAT may help in intra-articular biomechanics.