Sideband Signals Research Articles

In situ mixer calibration for superconducting quantum circuits

Mixers play a crucial role in superconducting quantum computing, primarily by facilitating frequency conversion of signals to enable precise control and readout of quantum states. However, imperfections, particularly local oscillator leakage and unwanted sideband signal, can significantly compromise control fidelity. To mitigate these defects, regular and precise mixer calibrations are indispensable, yet they pose a formidable challenge in large-scale quantum control. Here, we introduce an in situ and scalable mixer calibration scheme using superconducting qubits. Our method leverages the qubit's response to imperfect signals, allowing for calibration without modifying the wiring configuration. We experimentally validate the efficacy of this technique by benchmarking single-qubit gate error and qubit coherence time.

SSBI counteraction technology in a single photodetector-based direct detection system receiving an independent dual-single sideband signal

To further meet the large capacity, high spectrum efficiency (SE), reduce the signal-signal beat interference (SSBI) of the independent dual single sideband (ISB) system and the complexity of the receiver, we propose an iterative signal-signal beat interference counteraction (ISSBIC) algorithm to suppress SSBI. The 16-Gbps left sideband and the 16-Gbps right sideband signals in the ISB system are quadrature phase-shift keying (QPSK) modulated. After standard single-mode fiber (SSMF) transmission, the LSB and RSB signals are synthesized to a 16-quadrature amplitude modulation (QAM) signal after conversion through the photodetector (PD) square law. The simulation results show that the ISSBIC with just 2 iterations is superior to Kramers–Kronig (KK) receiver in processing the system error bit. In the meantime, the ISSBIC requires a sampling rate of 20GSa/s, whereas KK requires 40GSa/s. Moreover, the proposed ISSBIC algorithm has a simpler complexity. According to the simulation results, the suggested ISSBIC receiver can lower the ADC requirements and system costs, which opens up a wide range of applications in multiplex and higher SE transmission systems.

Compact low-half-wave-voltage thin film lithium niobate electro-optic phase modulator fabricated by photolithography-assisted chemo-mechanical etching (PLACE).

We present a compact dual-arm thin-film lithium niobate (TFLN) electro-optic phase modulator fabricated using the photolithography-assisted chemo-mechanical etching (PLACE) technique. The design of the device doubles the modulation amount compared to single-arm modulators while maintaining the same chip length. Achieving a half-wave voltage of approximately 3 V, the device outperforms conventional single-arm phase modulators. Furthermore, the phase modulator exhibits low sensitivity to optical wavelengths in the range of 1510-1600 nm and offers a low insertion loss of 2.8 dB. The capability to generate multiple sideband signals for optical frequency comb applications is also demonstrated, producing 29 sideband signals at an input microwave power of 2 W.

A Scheme for Generating Millimeter Wave Signals through 32-Tupling Frequency Multiplication without Filtering Using Eight Mach-Zehnder Modulators

In this paper, a filterless 32-tupling millimeter wave generation scheme based on eight MZMs is proposed. The system has an upper and lower parallel two-branch structure. The upper branch consists of two subsystems Sub-A and Sub-B in cascade, each subsystem contains four MZMs, and the MZMs are all operating at maximum transfer point (MATP). Sub-A mainly generates ±8th order optical sideband signal as the incident light signal of Sub-B. After modulation of Sub−B, the output signal is mainly ±16th order optical sideband signal containing the central optical carrier component. The optical attenuator (OATT) and optical phase shifter (OPS) of the lower branch are used to regulate the phase and amplitude of the optical carrier. The upper and lower branches are coupled, and the central optical carrier component is superimposed and cancelled so only the ±16th order optical sideband signal is retained. Finally, the 32-tupling frequency millimeter is generated by the photodiode (PD) receiver after photoelectric detection which receives and generates a 32-tupling frequency millimeter wave signal. The simulation results show that the 160 GHz millimeter wave signal can be obtained by driving the MZM with a 5 GHz RF signal, and the optical sideband suppression ratio (OSSR) and the RF sideband suppression ratio (RFSSR) are 52.6 dB and 44.75 dB, respectively. Theoretical analysis and simulation experiments are carried out for the proposed scheme which proves the feasibility of the scheme.

Tunable UV ∼ IR frequency comb generation via high-order sideband generation

We propose the generation of a widely tunable UV-to-IR frequency comb by high-order sideband generation (HSB) spectrum emitted from semiconductors. In our theoretical simulations, we demonstrate the high-order sideband signals of two series (2m Ωseed + (2n + 1) ωdriver, and (2m + 1) Ωseed + 2 nωdriver ), where m and n are integers of a seed pulse and a driver laser frequency, respectively. The simulations also reveal the intensity of HSB scale with the driver laser power, both perturbatively and non-perturbatively. We find that the harmonic position and spacing of the high-order sideband emission can be controlled by varying the seed pulse and driver photon energies. In the experiment, we applied a visible ( ℏΩseed = 3.1 eV, ∼400 nm) seed pulse and mid-infrared (MIR, ℏωdriver = 0.4 eV, 3.1 μm) driver pulses to ZnSe target. Our experimental observations confirmed the UV (4.7 eV, 263 nm and 3.9 eV, 317 nm) HSB generation.

Low sidelobe cosecant-squared pattern time-modulated antenna array with harmonic suppression

In this paper, a pulse shifting approach with phase-only weighting is proposed for a cosecant-squared radiation pattern time-modulated linear array (TMLA) synthesis. The sidelobe level (SLL) of fundamental signal and maximum sideband levels (SBLs) of harmonic signals is simultaneously reduced. This is achieved by controlling both the phase and the periodic switching time sequence of each element of the TMLA. In pulse shifting, the on–off switching sequence of each radiating element is characterized by a switch-on instant and interval within the modulation period which increases the degrees of freedom. A genetic algorithm (GA) is employed to optimize the switch-on and switch-off instants of each time pulse along with the phase weight for each element in the antenna array. The simulation results reveal that the proposed method can achieve the required patterns with very low SLL and SBLs.

Compact silicon-based Ka-band tunable-phase photonic microwave frequency downconverter.

In this paper, a compact silicon-based photonic microwave frequency downconverter with broadband operation capability and continuous phase shift tunability is proposed and experimentally demonstrated. The photonic converter mainly comprises two micro-ring modulators (MRMs) connected in parallel and a cascaded resonator-based optical bandpass filter (OBPF) whose size is merely 200 × 700 µm2. In the proposed device, a radio frequency (RF) signal and a local oscillator (LO) signal drive the two MRMs for realizing the electro-optic conversion. The OBPF is utilized for selecting the first-order sidebands of both RF and LO signals. By manipulating the phase difference between the RF and LO optical sidebands through thermal-optic effect, the phase of the obtained intermediate frequency (IF) signal from a photodiode can be tuned continuously. Experimental results demonstrate a 137° phase shift while the RF signals of 20 and 40 GHz are downconverted to an IF signal of 0.4 GHz, which indicates the photonic microwave downconverter can be used in the Ka-band phased-array receiver.

Microwave-multiplexed qubit controller using adiabatic superconductor logic

Cryogenic qubit controllers (QCs) are the key to build large-scale superconducting quantum processors. However, developing scalable QCs is challenging because the cooling power of a dilution refrigerator is too small (~10 μW at ~10 mK) to operate conventional logic families, such as complementary metal-oxide-semiconductor logic and superconducting single-flux-quantum logic, near qubits. Here we report on a scalable QC using an ultra-low-power superconductor logic family, namely adiabatic quantum-flux-parametron (AQFP) logic. The AQFP-based QC, referred to as the AQFP-multiplexed QC (AQFP-mux QC), produces multi-tone microwave signals for qubit control with an extremely small power dissipation of 81.8 pW per qubit. Furthermore, the AQFP-mux QC adopts microwave multiplexing to reduce the number of coaxial cables for operating the entire system. As a proof of concept, we demonstrate an AQFP-mux QC chip that produces microwave signals at two output ports through microwave multiplexing and demultiplexing. Experimental results show an output power of approximately −80 dBm and on/off ratio of ~40 dB at each output port. Basic mixing operation is also demonstrated by observing sideband signals.

High-accuracy optical vector network analyzer for optical notch and bandpass responses

A high-accuracy optical vector network analyzer (OVNA) based on optical carrier-suppressed double sideband (CS-DSB) modulation is proposed and experimentally demonstrated. The ±1st-order sideband signals are generated by CS-DSB modulation and then pass through the symmetric optical device under test (DUT). The band-stop or band-pass responses can be realized by detecting and processing the double frequency of the driven RF signal. Compared with the conventional symmetrical DSB-based OVNA, the measurement accuracy is improved by eliminating the errors caused by the even-order sidebands, and the complexity is reduced as the proposed method with only one step measurement can avoid the complex postprocessing. In addition, the optical carrier is aligned to the center frequency of the DUT by employing the Pound–Drever–Hall (PDH) technique, which provides stable measurement. At the same time, the limitation that the band-pass responses cannot be measured by the traditional single-sideband (SSB)-based OVNA is overcome. Additionally, accurate magnitude and phase responses of the DUT near the optical carrier can be also achieved since the proposed OVNA is optical filter-immune. The proposed method is theoretically analyzed and verified by experiment. A Fabry–Perot (FP) interferometer serves as the symmetric DUT; the band-stop responses in a frequency range of 6 GHz are obtained with a resolution of 1.2 MHz; and the band-pass responses with the range from 0 to 13 GHz offsetting the optical carrier are also obtained. The measurement time can reach up to 30 min with high stability. The proposed OVNA offers enhanced accuracy and a stable approach for applications in photonic systems and other innovations.

Joint signal-to-signal beat interference mitigation for the field recovery of symmetric carrier-assisted differential detection with low carrier-to-signal power ratio

As a combination of direct detection and coherent detection technologies, self-coherent detection has the advantages of low cost and optical field recovery ability. However, most of the self-coherent detection techniques are limited to single sideband (SSB) signals. Recently, carrier-assisted differential detection (CADD) has been proposed to realize complex-valued double sideband (DSB) signals, but it requires a high carrier-to-signal power ratio (CSPR) to mitigate the signal-to-signal beat interference (SSBI). Later, a more cost-effective symmetric CADD (S-CADD) has been proposed while the required CSPR is still high. In order to alleviate the high requirements of CSPR, we propose a scheme based on the joint of digital pre-distortion (DPD) at transmitter and clipping at receiver to further improve the S-CADD system performance. This joint processing can not only solve the problem of non-uniform distribution of subcarrier signal-to-noise ratio (SNR) caused by non-ideal transfer function, but also the error propagation problem caused by enhanced SSBI under low CSPR. After the validation of the 64 Gbaud 16-ary quadrature amplitude modulation (16-QAM) orthogonal frequency division multiplexing (OFDM) signal transmitted over 80 km standard single mode fiber (SSMF), the CSPR required by the proposed scheme to reach the 20% soft decision-forward error correction (SD-FEC) and 7% hard decision-forward error correction (HD-FEC) can be reduced by 1.3 dB and 2.8 dB, respectively, with a comparison of the conventional S-CADD. The results show the potential of the proposed scheme in the short-reach optical transmissions.

A Novel Frequency Doubling Radio on Fiber System Without Bit Walk-Off Effect by Inserting a Pilot Frequency Signal

A novel insertion pilot-frequency signal method for doubling frequency radio on fiber (ROF) system is proposed. At the center station (CS), the carrier emitting from the continuous wave (CW) laser is split into two branches. In one branch, a composite RF drive signal formed by combining the data modulated by a phased modulator (PM) and the data gained by an electrical gainer (EG) is loaded to the Mach-Zehnder modulator (MZM) to produce ± 1th order sideband signals. The data signal of down link is modulated only on −1th order sideband. The other branch is used as the pilot signal. At the base station (BS), the pilot signal is reflected out using a fiber Bragg grating (FBG) and used as the carrier for the uplink. The signal passing through the FBG is sent into the photodetector, and the twofold millimeter wave signal is generated. The mathematical analysis and simulated experiment are given. The innovation of this paper is to introduce the pilot optical signal method for carrier reuse in ROF, it can overcome the poor tunability and degraded downlink performance in the conventional carrier reuse in ROF. The effect of bit walk-off is eliminated due to the data of downlink and uplink being modulated on the −1th and 0th order sideband respectively.

Photon Generation Scheme of 32‐Fold Millimeter‐Wave Signal Based on Mach‐Zehnder Modulator

AbstractThis paper proposes a 32‐tupling frequency millimeter‐wave (MMW) filter‐free system based on four Mach‐Zehnder Modulators (MZM) connected in parallel and cascaded with a simple radio‐fiber (RoF) link structure. The four MZMs are all at the maximum transmission point (MATP), and the radio frequency (RF) driving voltage phase difference between MZMs is π /2. The center carrier is suppressed by using an optical attenuator (OATT) and an optical phase shifter (OPS). Two parallel MZMs can generate ±8th order and ±12th order optical sidebands, and the ±4th order optical sidebands can be suppressed by adjusting the modulation index m of the MZM, using cascaded two dual‐parallel MZMS(DPMZM) and the phase difference of the RF signal source is π/4 to generate ±16th order optical sidebands. The theoretical analysis and simulation experiments are performed for the scheme proposed in this paper. The results show that the simulated and theoretical values of the optical sideband suppression ratio (OSSR) for ±16th order optical sideband signals are 60.02 and 59.96 dB, respectively, and the simulated and theoretical values of the RF sideband suppression ratio (RFSSR) for the 32‐tupling MMW signal are 56.34 and 53.94 dB, respectively.

High resolution acoustic sensing based on microcavity optomechanical oscillator.

In this paper, a simple sensing method based on a silicon oxide microcavity optomechanical oscillator (OMO) is proposed and demonstrated for the detection of acoustic signals. Firstly, the resonance damping was reduced by improving the optical quality factor (Qo) and increasing the sphere-to-neck ratio. After optimizing the process, a microsphere OMO was fabricated, which has an ultra-high mechanical quality factor (6.8 × 106) and greater sphere-to-neck ratio (∼11:1), based on which ultra-narrow linewidth phonon laser (∼1 Hz) is constructed. Secondly, by changing the refractive index of the coupling interval, the low-frequency acoustic pressure signal is efficiently coupled into the microcavity OMO to construct a high-resolution acoustic sensor. This sensing mechanism can not only measure the acoustic pressure, but also use the sideband signal in the modulation mechanism to measure the frequency of acoustic signals (15 Hz∼16 kHz), the sensitivity is 10.3 kHz/Pa, the minimum detectable pressure is 1.1 mPa, and noise-limited minimum detectable pressure is 28.8 µPa/Hz1/2. It is the highest detection resolution compared with the same type of low-frequency acoustic signal detection currently reported. This OMO-based acoustic sensing detection method opens up a new path for future miniaturized, ultra-high-precision, and cost-effective acoustic sensing.

Preliminary searches for spin-dependent interactions using sidebands of nuclear spin-precession signals.

Various theories beyond the Standard Model predict new particles with masses in the sub-eV range with very weak couplings to ordinary matter. A new P-odd and T-odd interaction between polarized and unpolarized nucleons proportional to s⃗⋅r̂ is one such possibility, where r⃗=rr̂ is the spatial vector connecting the nucleons, and s⃗ is the spin of the polarized nucleon. Such an interaction involving a scalar coupling gsN at one vertex and a pseudoscalar coupling gpn at the polarized nucleon vertex can be induced by the exchange of spin-0 pseudoscalar bosons. We describe a new technique to search for interactions of this form and present the first measurements of this type. We show that future improvements to this technique can improve the laboratory upper bound on the product gsNgpn by two orders of magnitude for interaction ranges at the 100 micron scale.

Dual-heterodyne Kelvin probe force microscopy.

We present a new open-loop implementation of Kelvin probe force microscopy (KPFM) that provides access to the Fourier spectrum of the time-periodic surface electrostatic potential generated under optical (or electrical) pumping with an atomic force microscope. The modulus and phase coefficients are probed by exploiting a double heterodyne frequency mixing effect between the mechanical oscillation of the cantilever, modulated components of the time-periodic electrostatic potential at harmonic frequencies of the pump, and an ac bias modulation signal. Each harmonic can be selectively transferred to the second cantilever eigenmode. We show how phase coherent sideband generation and signal demodulation at the second eigenmode can be achieved by using two numerical lock-in amplifiers configured in cascade. Dual-heterodyne KPFM (DHe-KPFM) can be used to map any harmonic (amplitude/phase) of the time-periodic surface potential at a standard scanning speed. The Fourier spectrum (series of harmonics) can also be recorded in spectroscopic mode (DHe-KPFM spectroscopy), and 2D dynamic images can be acquired in data cube mode. The capabilities of DHe-KPFM in terms of time-resolved measurements, surface photovoltage (SPV) imaging, and detection of weak SPV signals are demonstrated through a series of experiments on difference surfaces: a reference substrate, a bulk organic photovoltaic heterojunction thin film, and an optoelectronic interface obtained by depositing caesium lead bromide perovskite nanosheets on a graphite surface. The conclusion provides perspectives for future improvements and applications.

Mitigating Quantum Decoherence in Force Sensors by Internal Squeezing.

The most efficient approach to laser interferometric force sensing to date uses monochromatic carrier light with its signal sideband spectrum in a squeezed vacuum state. Quantum decoherence, i.e., mixing with an ordinary vacuum state due to optical losses, is the main sensitivity limit. In this Letter, we present both theoretical and experimental evidence that quantum decoherence in high-precision laser interferometric force sensors enhanced with optical cavities and squeezed light injection can be mitigated by a quantum squeeze operation inside the sensor's cavity. Our experiment shows an enhanced measurement sensitivity that is independent of the optical readout loss in a wide range. Our results pave the way for quantum improvements in scenarios where high decoherence previously precluded the use of squeezed light. Our results hold significant potential for advancing the field of quantum sensors and enabling new experimental approaches in high-precision measurement technology.

Adaptive spectrum segmentation Ramanujan decomposition and its application to gear fault diagnosis

Ramanujan Fourier mode decomposition (RFMD) is a novel non-stationary signal decomposition method, which can decompose a complex signal into several components and extract the periodic characteristics of the signal. However, the mode generation method adopted by RFMD does not consider the physical meaning of the component signal, which makes over-decomposition when dealing with real-life gear signals with complex modulation characteristics, thus destroying the integrity of the signal sideband, increasing the difficulty of subsequent analysis, and even losing key fault information. The iterative envelope-segmentation algorithm combines the modulation characteristics of the local fault gear signal and divides the original signal into a limited number of dominant frequency bands containing the modulation region in the Fourier spectrum, thereby ensuring that the obtained frequency bands contain rich fault information. Based on the above algorithm, a new adaptive decomposition method is proposed in this paper, which is adaptive spectrum segmentation Ramanujan decomposition (ASSRD). ASSRD uses fault envelope harmonic noise ratio as the index to evaluate the fault information content of component signals and uses it to assist the iterative envelope-segmentation algorithm to complete the adaptive segmentation of the Fourier spectrum. Finally, based on the segmentation result, the inverse RFT reconstruction of each frequency band is performed. Thus, the signal is decomposed into a finite number of component signals containing rich fault information. In addition, through the experiment on the gear simulation signal and the measured crack fault gear signal, the ASSRD method is compared with the original RFMD method and the existing ensemble empirical mode decomposition (EMD), variational mode decomposition, empirical wavelet transform, and singular spectrum decomposition method, verifying the feasibility and superiority of ASSRD in gear fault diagnosis. Besides, a comparative experiment based on compound faults diagnosis is carried out, in which ensemble EMD, Fourier decomposition method, empirical wavelet transform, and sparse decomposition are involved. The results show that the proposed method can extract the local fault information in the gear signal more effectively, and the performance is better than the comparison method.

High rejection self-oscillating up-conversion mixer for fifth-generation communications

<span lang="EN-US">This paper presents the design of a pseudomorphic high electron mobility transistor (pHEMT) self-oscillating mixer (SOM) for millimeter wave wireless communication systems. The 180° out-of-phase technique is chosen to both improve the desired lower sideband (LSB) signal and to achieve a satisfactory rejection of the unwanted signals (LO, USB and IF). This SOM is designed on the PH15 process of UMS foundry which is based on 0.15 µm GaAs pHEMT. The signal is up-converted from 2 GHz-IF frequency to 26 GHz-LSB frequency, using an autogenerated 28 GHz-LO signal. Simulations were performed using the advanced design system (ADS) workflow. They show 6.4 dB conversion gain and a signal rejection rate of 29.7 dB for the unwanted USB signal. the chip size is 3.6 mm<sup>2</sup>.</span>

High-average-power single-longitudinal-mode pulse laser based on a pulse saturation seed-injection locking OPO.

A high-average-power and narrow-linewidth nanosecond (ns) pulse 824 nm laser is a crucial source for the generation of deep-ultraviolet (DUV) 248 nm laser by means of the sum-frequency process with the 354.5 nm laser. To this purpose, in this Letter, we present a seed-injection-locked high-average-power ns pulse single-longitudinal-mode (SLM) 824 nm laser. By developing a novel, to the best of our knowledge, pulse-saturated seed-injection locking method, disturbance of the pulse laser on the locking of the injected seed laser is successfully eliminated. As a result, the output power of 824 nm laser is up to 21.2 W at the incident pump power of 48.1 W, and the pulse width is 15 ns. Especially, the signal-to-noise ratio of the detected modulated sideband signal exceeds 28 dB, which ensures that the achieved linewidth of the 824 nm laser is as narrow as 38.8 MHz. These results demonstrate the potential of the proposed pulse saturation seed-injection locking OPO cavity for high-power and narrow-linewidth laser applications.

On measurements of spurious components of heterodyne signal in radiometric receivers

With a heterodyne frequency conversion, a significant contribution to the intrinsic noise of the radiometric receiver is made by a heterodyne. The spectral components generated by the heterodyne will be present in the processed signal at the output of the radiometric receiver and may manifest themselves when analyzing the received signal in spectral lines when high frequency resolution is required for processing. The purpose of the work is to analyze various types of modulation of the heterodyne signal, including modulation with an arbitrary phase shift between the components in the lower and upper side bands of the heterodyne signal. In this article, the methods of frequency transfer used in determining the spectral composition of the signal received by a radiometric receiver are considered. For heterodyne frequency conversion, in addition to the classical types of parasitic modulation of the heterodyne signal described in the literature – amplitude, phase (frequency) and single-band modulation, modulation with an arbitrary phase shift between the components in the lower and upper side bands of the heterodyne signal is considered. It is shown that with a small deviation of the frequencies of the modulating signal, ambiguity is possible in determining the level of components when using signal analyzers to measure the characteristics of heterodynes of radiometric receivers. The results of the analysis performed in the article can be used in the design of heterodynes with multiple output frequencies, taking into account the spectral comtent of the synthesized signal. The study was carried out at the expense of the grant of the Russian Science Foundation No. 22-19-00063 dated 13.05.2022. https://rscf.ru/project/22-19-00063.