Segregation Rate Research Articles

Anisotropic radiation-induced segregation in 316L austenitic stainless steel with grain boundary character

Radiation-induced segregation (RIS) and subsequent depletion of chromium along grain boundaries has been shown to be an important factor in irradiation-assisted stress corrosion cracking in austenitic face-centered cubic (fcc)-based alloys used for nuclear energy systems. A full understanding of RIS requires examination of the effect of the grain boundary character on the segregation process. Understanding how specific grain boundary structures respond under irradiation would assist in developing or designing alloys that are more efficient at removing point defects, or reducing the overall rate of deleterious Cr segregation. This study shows that solute segregation is dependent not only on grain boundary misorientation, but also on the grain boundary plane, as highlighted by markedly different segregation behavior for the Σ3 incoherent and coherent grain boundaries. The link between RIS and atomistic modeling is also explored through molecular dynamic simulations of the interaction of vacancies at different grain boundary structures through defect energetics in a simple model system. A key insight from the coupled experimental RIS measurements and corresponding defect–grain boundary modeling is that grain boundary–vacancy formation energy may have a critical threshold value related to the major alloying elements’ solute segregation.

Simulation of particle mixing and segregation in bidisperse gas fluidized beds

The mixing and segregation of particles of various types in gas–solid fluidized beds is a common phenomenon that is observed in experimental investigations. Generally, it is necessary to understand the phenomenon of mixing and segregation in gas-fluidized beds for the optimal design operation and scale-up of many industrial processes. To gain more insight into these, bed dynamics have been studied using a fully coupled Computational Fluid Dynamics/Discrete Element Method model (CFD/DEM), in which the particles are tracked individually using Newton's law of motion, and a newly developed continuum-based Multi-Fluid Model [MFM, van Sint Annaland et al. (2009a). Chem. Eng. Sci. 64, 4222–4236]. Rigorous comparisons have been made between results from laboratory experiments and the CFD/DEM and MFM. The CFD/DEM was found to reliably predict the segregation rates in low beds, provided that an appropriate gas-particle drag relation is used that accounts for the effect of polydispersity.

Segregation and African-American imprisonment rates for drug offenses

Scholars argue that the dramatic increase in the African-American incarceration rate that occurred after the civil rights era was in part a reflection of the declining utility of residential segregation as a modern form of social control. Existing research has not thoroughly investigated the association between racial segregation and prison admission rates. Using 2002 data for 198 metropolitan counties, this research examines the relationship between two dimensions of racial residential segregation and African-American prison admission rates for drug offenses. The results from a multivariate regression analysis reveal that the prison admission rates of African-Americans for drug offenses are lower in counties where White residents are more residentially isolated from African-Americans. The admission rates are unaffected by the dissimilarity index. Consistent with recent research on the level of coercive control, the findings suggest that the effect of the percentage of African-Americans residing in an area is nonlinear.

Fluidized bed desliming in fine particle flotation – Part II: Flotation of a model feed

This is second in a series of papers concerned with the performance of a novel technology, the Reflux Flotation Cell. Part I examined the system hydrodynamics, commencing with a gas–liquid system and examination of the fluidization boundary condition. The desliming, or potential to reject entrained fine gangue particles from the product overflow, was investigated by introducing hydrophilic particles. In Part II, a model feed consisting of hydrophobic coal particles and hydrophilic silica was introduced. The separation of these two components was investigated across an extreme range in the applied gas and wash water fluxes, well beyond the usual limits of conventional flotation.The Reflux Flotation Cell challenges conventional flotation cell design and operation in three ways. Firstly, the upper free-surface of the flotation cell is enclosed by a fluidized bed distributor in order to fluidize the system in a downwards configuration, counter-current to the direction of the rising air bubbles. Secondly, a system of inclined channels is located below the vertical section of the cell, providing a foundation for increasing bubble–liquid segregation rates. Thirdly, the system is operated with a bubbly zone, hence in the absence of a froth zone. This combination of conditions provides for the establishment of a high volume fraction of bubbles in the bubbly zone, of high permeability, ideal for promoting enhanced counter-current washing of the rising bubbles, and hence high quality desliming. The arrangement permitted operation at extreme levels in the value of the fluidization (wash water) flux and the gas flux, with the fluidization flux set at up to 2.1cm/s and the gas flux set at up to 4.7cm/s for a mean bubble size, db, of 1.5mm. These gas and wash water fluxes corresponded to a bubble surface flux of 188m2/m2s and a positive bias flux of 1.7cm/s. Thus the operating regime was shown to be far broader than that achieved by conventional flotation, thereby confirming the robust nature of the system. The model flotation feed provided a basis for establishing the flotation performance across this vast regime of operation. Full combustible recovery of fine coal and full rejection of mineral matter were achieved, with good agreement with the Tree Flotation curve. At extreme levels of wash water addition it was possible to selectively strip poorer floating coal particles from the bubble surface, and in turn achieve beneficiation results significantly better than those defined by the Tree Flotation method.

Segregation and the Social Relations of Place, Bombay, 1890–1910

For many, a defining feature of the colonial Indian city is the high rate of segregation of its European and Indians residents. Building on recent work that explores the messy realities of social and spatial relations, this paper argues that the social geographies of the colonial city were built on the social relations of place—the network of social relations that are bound up with a particular material setting. The result was that social spaces were centred on overlapping geographic patterns, intense negotiations over space, and heterogeneous lived-in spaces. In this paper, these points are examined through the case of Bombay's Modern Town at the turn of the twentieth century. Modern Town was supposedly the home of the city's European population and it stood in sharp contrast to the city's Native Town. However, Modern Town did not conform to the spatial topographies described by most writers. While formal residential segregation existed, social and economic articulation and interaction ensured that the district's social spaces were meshed in differentiated and complex ways.

Metropolitan racial residential segregation and cardiovascular mortality: exploring pathways.

Racial residential segregation has been associated with an increased risk for heart disease and stroke deaths. However, there has been little research into the role that candidate mediating pathways may play in the relationship between segregation and heart disease or stroke deaths. In this study, we examined the relationship between metropolitan statistical area (MSA)-level segregation and heart disease and stroke mortality rates, by age and race, and also estimated the effects of various educational, economic, social, and health-care indicators (which we refer to as pathways) on this relationship. We used Poisson mixed models to assess the relationship between the isolation index in 265 U.S. MSAs and county-level (heart disease, stroke) mortality rates. All models were stratified by race (non-Hispanic black, non-Hispanic white), age group (35-64 years, ≥ 65 years), and cause of death (heart disease, stroke). We included each potential pathway in the model separately to evaluate its effect on the segregation-mortality association. Among blacks, segregation was positively associated with heart disease mortality rates in both age groups but only with stroke mortality rates in the older age group. Among whites, segregation was marginally associated with heart disease mortality rates in the younger age group and was positively associated with heart disease mortality rates in the older age group. Three of the potential pathways we explored attenuated relationships between segregation and mortality rates among both blacks and whites: percentage of female-headed households, percentage of residents living in poverty, and median household income. Because the percentage of female-headed households can be seen as a proxy for the extent of social disorganization, our finding that it has the greatest attenuating effect on the relationship between racial segregation and heart disease and stroke mortality rates suggests that social disorganization may play a strong role in the elevated rates of heart disease and stroke found in racially segregated metropolitan areas.

A SNP-Based Genetic Linkage Map of Soybean Using the SoyS - NP6K Illumina Infinium BeadChip Genotyping Array

This study reports a high density genetic linkage map based on the ‘Maryland 96-5722’ by ‘Spencer’ recombinant inbred line (RIL) population of soybean [Glycine max (L.) Merr.] and constructed exclusively with single nucleotide polymorphism (SNP) markers. The Illumina Infinium SoySNP6K BeadChip genotyping array produced 5,376 SNPs in the mapping population, with a 96.75% success rate. Significant level of goodness-of-fit for each locus was tested based on the observed vs. expected ratio (1:1). Out of 5,376 markers, 1,465 SNPs fit the 1:1 segregation rate having ≤20% missing data plus heterozygosity among the RILs. Among this 1,456 just 657 were polymorphic between the parents DNAs tested. These 657 SNPs were mapped using the JoinMap 4.0 software and 550 SNPs were distributed on 16 linkage groups (LGs) among the 20 chromosomes of the soybean genome. The total map length was just 201.57 centiMorgans (cM) with an average marker density of 0.37 cM. This is one of the high density SNP-based genetic linkage maps of soybean that will be used by the scientific community to map quantitative trait loci (QTL) and identify candidate genes for important agronomic traits in soybean.

Experimental Research on Coal Gangue Grouting Material for Gob Filling

Grouting fill is one of the main methods of coal gob treatment. The grouting properties directly affect the effect of grouting treatment. Cement-fly ash grout is widely used in the treatment of coal gob. But in many gob grouting fill projects, due to the lack of fly ash, we need to look for other low-cost grouting materials. Study was made through laboratory experiment on the properties of cement-coal gangue materials used for the gob grouting. In this paper, the correlation of water-solid ratio, cement content, admixture, concretion compression strength, setting time, viscosity, water segregation rate and hardening rate is discussed in the case of use of large gangue content cement. The test results show that compared with the grout not go through the activation process, the blended cement grout mixed with coal gangue powder activated by low temperature and mechanical crushing has high concretion compression strength. Water glass has a great effect on the viscosity, initial setting time and final setting time, which can be used to adjust the grout properties to accommodate grouting environment requirements. This grout has the advantage of wide range sources of raw materials, and can be used to solve the lack of fly ash and gangue resource utilization problems.

Sex ratio, spatial segregation, and fertilization rates of the epiphyllous moss Crossomitrium patrisiae (Brid.) Müll.Hal. in the Brazilian Atlantic rainforest

In order to investigate which mechanisms the epiphyllous moss Crossomitrium patrisiae employs to overcome the typical constraints of dioicy in light of its spatially isolated habitat, we tested the predictions that high fertilization rates are achieved due to (1) high rates of sexual expression, (2) balanced sex ratios, and (3) high co-occurrence of both sexes in the same colony (leaf). Seven hundred and ninety-seven ramets were studied for total length, presence, and number of gametoecia and number of fertilized perichaetia in the female according to spatial segregation at leaf- and shrub-scales. High rates of sexual expression (76%) were confirmed. The other two predictions, however, were not upheld as C. patrisae exhibited a strong male bias (0·43 ♀∶1 ♂ at ramet level, n = 604). Despite considerable spatial segregation (co-occurrence of sexes was seen in 36·7% of shrubs and 12·8% of colonies), this species revealed one of the highest fertilization rates ever reported for a dioicous bryophyte at three spatial scales: nearly 90% of the mixed colonies bore sporophytes, 40% of all female ramets, and 74% of female ramets occurring in mixed colonies bore sporophytes. Thus, the relative rareness of females may be a phenotypic response due to heavy investment in sporophyte maturation as demonstrated by the high fertilization success of females. High rates of sexual expression and the occurrence of fertilization in nearly all cases of coincidence of sexes in common colonies, with low levels of abortion, contribute to the sexual reproductive success and, subsequently, the long-term survival of this species.

Residential Segregation and Gonorrhea Rates in US Metropolitan Statistical Areas, 2005–2009

The residential segregation of black populations, often in areas of high-economic disadvantage and low social status, may play a crucial role in the observed racial inequities in sexually transmitted disease rates. An ecological analysis of 2005 to 2009 average gonorrhea rates was performed across 277 US metropolitan statistical areas (MSAs). The black isolation index and Gini index of income inequality were used as proxy measures for racial and economic residential segregation respectively, derived from 2005 to 2009 US Census estimates. We used logistic regression modeling to produce estimates of odds ratios (ORs) and 95% confidence intervals (CIs) for the association between the segregation indices, both independently and in combination, on gonorrhea rates in MSAs. Effect measure modification was assessed by calculating the relative excess risk due to interaction between the 2 indices. Compared with MSAs with low levels of racial segregation, MSAs with high levels of racial segregation had increased odds of high gonorrhea rates (adjusted OR, 3.37; 95% CI, 1.23-9.21). Similarly, higher levels of income inequality predicted higher gonorrhea rates, although this association did not persist after adjustment for potential confounders (adjusted OR, 1.54; 95% CI, 0.74-3.24). In combined models, the influence of racial residential segregation on gonorrhea rates was stronger than that of income inequality-based segregation; there was no evidence of additivity or a multiplicative interaction. Residential segregation by race or income equality may be a key component in the perpetuation of high rates of gonorrhea and other sexually transmitted diseases among black populations in the United States.

Discrete particle simulation of solid separation in a jigging device

This paper presents a numerical study of solid separation in a jigging device, which is a high yield and high recovery gravity separation device widely used in ore processing. The mathematical model adopted is a combination of computational fluid dynamics (CFD) for the liquid flow and discrete element method (DEM) for particle motion. The motion of individual particles is 3 dimensional (3D) and the flow of continuous liquid is 2 dimensional (2D), considering the bed thickness is only 1/3rd of the bed width, and one CFD computational cell is used through the thickness. Periodic boundary conditions are applied on the front and rear walls to emulate a bed of larger thickness using a relatively small number of particles. Stratification is heavily dependent on fluid motion through the jig. The study explores 5 different pulsation profiles. The profiles used are — sinusoidal, triangle, sawtooth-backward, sawtooth-forward, and trapezoidal. The initial packing conditions consist of a binary-density particle system where the light particles and heavy particles, have respective densities of 2540 and 4630kg/m3. There are 1130 particles each 1cm in diameter. As an initial comparison, all simulations are conducted using a fixed peak–peak amplitude and pulsation period. Their relative performances are compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. The underlying mechanisms are explained in terms of particle–fluid interaction force. These quantitative comparisons demonstrate significant differences in the segregation rate and energy used for various pulsation profiles.

Segregación residencial socioeconómica en la Gran Área Metropolitana de Costa Rica. Niveles y patrones entre 1984 y 2000

The paper examines the socio-economic residential segregation indices in three scales, and analyzed the levels and patterns of segregation and its trend over time by comparing the indices1984 and 2000. Among the most notable findings, is the correspondence with the trends in residential segregation in other Latin American cities: greater segregation on a smaller scale and a decrease in the time of the levels of segregation. Furthermore, the Greater Metropolitan Area (GAM) has lower overall rates of segregation that several Latin American cities, particularly Santiago de Chile, a difference that is explained by the origin and historical structure of the city, because GAM is characterized as an urban space less polarized, more heterogeneous, with a concentration of elites in small areas scattered throughout the city and a more dispersed distribution of a large middle class.

CFD–DEM investigation of particle separations using a sinusoidal jigging profile

This paper presents a numerical investigation of solid separation in jigging device. Jigging is a gravity separation method commonly used by the minerals industry to separate coal, iron ore, diamonds and other minerals on the basis of particle size and/or density. Separation is recognised as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile in relation to a wide criterion on jigging performance. Modelling of the liquid–solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1cm in diameter. A range of jigging profiles have been implemented in mineral processing. In this study the sinusoidal pulsation profile is selected adopting variations in both amplitude and frequency. The performance of profile variants are compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system. In addition, boundaries of operation are found in terms of frequency and amplitude limits and the concentration mechanics are investigated in these regions.

Reduced Life- and Healthspan in Mice Carrying a Mono-Allelic BubR1 MVA Mutation

Mosaic Variegated Aneuploidy (MVA) syndrome is a rare autosomal recessive disorder characterized by inaccurate chromosome segregation and high rates of near-diploid aneuploidy. Children with MVA syndrome die at an early age, are cancer prone, and have progeroid features like facial dysmorphisms, short stature, and cataracts. The majority of MVA cases are linked to mutations in BUBR1, a mitotic checkpoint gene required for proper chromosome segregation. Affected patients either have bi-allelic BUBR1 mutations, with one allele harboring a missense mutation and the other a nonsense mutation, or mono-allelic BUBR1 mutations combined with allelic variants that yield low amounts of wild-type BubR1 protein. Parents of MVA patients that carry single allele mutations have mild mitotic defects, but whether they are at risk for any of the pathologies associated with MVA syndrome is unknown. To address this, we engineered a mouse model for the nonsense mutation 2211insGTTA (referred to as GTTA) found in MVA patients with bi-allelic BUBR1 mutations. Here we report that both the median and maximum lifespans of the resulting BubR1 +/GTTA mice are significantly reduced. Furthermore, BubR1 +/GTTA mice develop several aging-related phenotypes at an accelerated rate, including cataract formation, lordokyphosis, skeletal muscle wasting, impaired exercise ability, and fat loss. BubR1 +/GTTA mice develop mild aneuploidies and show enhanced growth of carcinogen-induced tumors. Collectively, these data demonstrate that the BUBR1 GTTA mutation compromises longevity and healthspan, raising the interesting possibility that mono-allelic changes in BUBR1 might contribute to differences in aging rates in the general population.

The influence of end walls on the segregation pattern in a horizontal rotating drum

The influence of end walls on segregation of bidisperse granular beds in a short rotating horizontal drum is studied by a discrete element method. Whereas non-closed periodically continued drums segregate radially, all simulations of drums with end walls resulted in axial segregation with two bands at low friction between the particles and the end-wall, and three bands at high friction. Various simulations show irregular transitions between two approximately equally stable states, with rapid oscillations preceding the conversions. The formation of two axial bands decreases the energy dissipation by the bed, whereas neither radial segregation nor axial segregation into three bands reduced the power absorption at constant angular velocity. Roughening up the end-walls also increased the rate of axial segregation.

Segregation Behaviour of Particles in Gas Solid Fluidized Beds at Elevated Pressure

A comprehensive mathematical model based on the discrete particle model and computational fluid dynamics was utilized to investigate mixing and segregation of particles in fluidized beds at high pressure. To quantify the extent of mixing in the bed, the Lacey mixing index was used. Simulations were carried out with different mass fractions of small particles at various pressures ranging from 1 to 64 bar and at various superficial gas velocities. The results showed that the bed transforms from a segregated state to a fully mixed condition when the operating pressure is increased. Vertical segregation of particles at low pressure was replaced by horizontal segregation of particles at high pressures in which small particles were collected mainly near the walls and large particles at the center of the bed. At the same pressure, the rate of segregation decreased with increasing the mass fraction of small particles.

Optimization of the electrical properties of Ti–Nb stabilized ferritic stainless steel SOFC interconnect alloy upon high-temperature oxidation: The role of excess Nb on the interfacial oxidation at the oxide–metal interface

Interfacial oxidation of Nb and Si at 650 °C on Laves phase forming Ti–Nb stabilized ferritic stainless steel (Fe–19Cr–0.9Si–0.2Nb–0.1Ti (at.%), grade EN 1.4509) was studied by electrochemical impedance spectroscopy and photoelectron spectroscopy. It was found that excess Nb efficiently hinders the formation of electrically resistive SiO2 layer at the oxide–metal interface. The beneficial role of Nb was attributed to its high segregation rate and the formation of conductive oxides at the interface. However, the oxidation was strongly influenced by age-precipitation of the Laves (FeNbSi)-type intermetallic phase, which removed free Nb from the alloy solution and thus allowed SiO2 layer to form more easily. These results can be applied to optimize the oxide scale composition by Nb alloying of the ferritic stainless steel to maintain high performance under various operation conditions, particularly in solid oxide fuel cell applications.

Study on the Diffusion Coefficient in NGS under Low Tensile Stress

In this paper, the diffusion coefficient of vacancy-solute complex and diffusion coefficient of solute atoms, P, in non-equilibrium grain-boundary segregation under low tensile stress in steel 12Cr1MoV are calculated based on the model developed by Xu. Both the simulation and experimental kinetics curves are achieved. Results show that the calculated result with the kinetic equations perfectly fits with the experimental observations for phosphorus in steel 12Cr1MoV under low tensile stress. In the segregation process, the rate of phosphorus segregation is high due to a large diffusivity of the complex. In the de-segregation process, the level of phosphorus segregation decreases with increasing stress aging time. But the rate of phosphorus desegregation from grain boundaries to centre is slower compared with that in segregation for the diffusion coefficient of phosphorus atoms is far lower than the complexes.

Heteroplasmy of Mouse mtDNA Is Genetically Unstable and Results in Altered Behavior and Cognition

Maternal inheritance of mtDNA is the rule in most animals, but the reasons for this pattern remain unclear. To investigate the consequence of overriding uniparental inheritance, we generated mice containing an admixture (heteroplasmy) of NZB and 129S6 mtDNAs in the presence of a congenic C57BL/6J nuclear background. Analysis of the segregation of the two mtDNAs across subsequent maternal generations revealed that proportion of NZB mtDNA was preferentially reduced. Ultimately, this segregation process produced NZB-129 heteroplasmic mice and their NZB or 129 mtDNA homoplasmic counterparts. Phenotypic comparison of these three mtDNA lines demonstrated that the NZB-129 heteroplasmic mice, but neither homoplasmic counterpart, had reduced activity, food intake, respiratory exchange ratio; accentuated stress response; and cognitive impairment. Therefore, admixture of two normal but different mouse mtDNAs can be genetically unstable and can produce adverse physiological effects, factors that may explain the advantage of uniparental inheritance of mtDNA.

Chromosome Segregation Analysis in Human Embryos Obtained from Couples Involving Male Carriers of Reciprocal or Robertsonian Translocation

The objective of this study was to investigate the frequency and type of chromosome segregation patterns in cleavage stage embryos obtained from male carriers of Robertsonian (ROB) and reciprocal (REC) translocations undergoing preimplantation genetic diagnosis (PGD) at our reproductive center. We used FISH to analyze chromosome segregation in 308 day 3 cleavage stage embryos obtained from 26 patients. The percentage of embryos consistent with normal or balanced segregation (55.1% vs. 27.1%) and clinical pregnancy (62.5% vs. 19.2%) rates were higher in ROB than the REC translocation carriers. Involvement of non-acrocentric chromosome(s) or terminal breakpoint(s) in reciprocal translocations was associated with an increase in the percent of embryos consistent with adjacent 1 but with a decrease in 3∶1 segregation. Similar results were obtained in the analysis of nontransferred embryos donated for research. 3∶1 segregation was the most frequent segregation type in both day 3 (31%) and spare (35%) embryos obtained from carriers of t(11;22)(q23;q11), the only non-random REC with the same breakpoint reported in a large number of unrelated families mainly identified by the birth of a child with derivative chromosome 22. These results suggest that chromosome segregation patterns in day 3 and nontransferred embryos obtained from male translocation carriers vary with the type of translocation and involvement of acrocentric chromosome(s) or terminal breakpoint(s). These results should be helpful in estimating reproductive success in translocation carriers undergoing PGD.