Detail Reproduction Research Articles

Influence of delayed pouring on irreversible hydrocolloid properties

The aim of this study was to evaluate the physical properties of irreversible hydrocolloid materials poured immediately and after different storage periods. Four alginates were tested: Color Change (Cavex); Hydrogum (Zhermack); Hydrogum 5 (Zhermack); and Hydro Print Premium (Coltene). Their physical properties, including the recovery from deformation (n = 3), compressive strength (n = 3), and detail reproduction and gypsum compatibility (n = 3), were analyzed according to ANSI/ADA specification no. 18. Specimens were stored at 23ºC and humidity and were then poured with gypsum immediately and after 1, 2, 3, 4, and 5 days. The data were analyzed by two-way analysis of variance (ANOVA) and Tukey's test at p < 0.05. All of the alginate impression materials tested exhibited detail reproduction and gypsum compatibility at all times. Hydro Print Premium and Hydrogum 5 showed recovery from deformation, as established by ANSI/ADA specification no. 18, after 5 days of storage. As the storage time increased, the compressive strength values also increased. Considering the properties of compounds' recovery from deformation, compressive strength, and detail reproduction and gypsum compatibility, irreversible hydrocolloids should be poured immediately.

Effect of disinfection on irreversible hydrocolloid and alternative impression materials and the resultant gypsum casts

Many new products have been introduced and marketed as alternatives to traditional irreversible hydrocolloid materials. These alternative materials have the same structural formula as addition reaction silicone, also known as vinyl polysiloxane (VPS), impression materials. Currently, there is limited in vitro and in vivo research on these products, including on the effects of chemical disinfectants on the materials. The purpose of this study was to compare the effects of a spray disinfecting technique on a traditional irreversible hydrocolloid and 3 new alternative impression materials in vitro. The tests were performed in accordance with the American National Standards Institute/American Dental Association (ANSI/ADA) Specification Nos. 18 and 19. Under standardized conditions, 100 impressions were made of a ruled test block with an irreversible hydrocolloid and 3 alternative impression materials. Nondisinfected irreversible hydrocolloid was used as the control. The impressions were examined for surface detail reproduction before and after disinfection with a chloramine-T product. Type III and Type V dental stone casts were evaluated for linear dimensional change and gypsum compatibility. Comparisons of linear dimensional change were analyzed with 2-way ANOVA of mean ranks with the Scheffé post hoc comparisons (α=.05). Data for surface detail reproduction were analyzed with the Wilcoxon Signed-Rank procedure and gypsum compatibility with the Kruskal-Wallis Rank procedure (α=.05). The alternative impression materials demonstrated significantly better outcomes with all 3 parameters tested. Disinfection with chloroamine-T did not have any effect on the 3 alternative impression materials. The irreversible hydrocolloid groups produced the most variability in the measurements of linear dimensional change. All of the tested materials were within the ADA's acceptable limit of 1.0% for linear dimensional change, except for the disinfected irreversible hydrocolloid impression material. The alternative impression materials performed best for the parameters tested. Spray disinfection had no effect on the alternative impression materials.

Surface detail reproduction under simulated pulpal pressure: A 3-dimensional optical profilometer and scanning electron microscopy evaluation

It is not clear whether more hydrophilic impression materials are better able to copy and transfer dentin surface detail than less hydrophilic ones. The purpose of this study was to evaluate the reproduction of dentin surface detail by means of hydrophobic and hydrophilic elastomeric impression materials under simulated pulpal pressure and their ability to transfer surface detail onto casts produced from such impressions. The wettability of the impression materials (n=8) was determined by contact angle measurement with an evolution period of 135 seconds. Dentin moisture was provided by means of pulpal pressure simulation, and objective analyses were performed by measuring the average roughness value (Ra) with a 3-D optical profilometer (n=10). One specimen from each group was analyzed with scanning electron microscopy. Contact-angle values were analyzed with a repeated measures ANOVA, and detail reproduction was tested with 3-way ANOVA (α=.05). The Bonferroni correction was used to control Type I error for follow-up analyses. Contact angle measurements revealed significant differences depending on the impression material used and time of the measurement (P<.001). The Ra values of the hydrophilic impression materials, which were made from dry specimens, and the pulpal pressure simulated dentin surfaces did not differ from the dentin surfaces (P>.013). The hydrophobic impression material showed similar detail reproduction ability in a dry field, but loss of detail (evaluated subjectively) and increased roughness values (evaluated objectively) were recorded in a moisturized field (P=.004). Polyurethane-based cast material successfully reproduced the surface texture (P≥.006), whereas Type IV gypsum material was unable to reproduce this texture to the same extent. The hydrophilic impression materials tested showed similar ability to reproduce detail under simulated pulpal pressure. Polyurethane-based cast material successfully reproduced the surface texture.

The influence of mixing methods and disinfectant on the physical properties of alginate impression materials

The aims of this in vitro study were to quantify the effect of manual versus automatic mixing and of using a disinfectant on mechanical properties of three different alginate impression materials. Two of the three alginates tested were especially developed for orthodontic use: Orthotrace® and Orthofine® while the third was a conventional alginate CA37FS®. Alginates were mixed by hand or automatically using a Cavex alginate mixer II®. Mixing was performed at room temperature using tap water. The material was allowed to set in a water bath at 35°C (±1°C), simulating intra-oral setting conditions, and half of the samples were disinfected before testing. For each tested material, 10 standardized samples were used. The disinfectant used was the CavexImpreSafe® that has a bactericide, virucide, and fungicide function. The specimens were exposed for 3 minutes in a 3% solution and were then tested according to the ISO 1563: 1990 (E) standard specifications. Descriptive statistics and three-way analysis of variance were performed, and a 5% significance level was used for statistical analysis. Evaluation of tensile strength and elastic recovery of different alginate samples, hand versus automatical mixing or disinfected versus not disinfected, resulted in significant differences for all materials except for Orthofine®. Considering detail reproduction, all three alginates evaluated reproduced the 50-μm line successfully without interruption. The mixing method can significantly affect the elastic recovery and tensile strength of the alginates tested while the effect of using a disinfectant is less explicit.

Effect of disinfection and accelerated ageing on dimensional stability and detail reproduction of a facial silicone with nanoparticles

The aim of the present study was to evaluate the effect of disinfection and accelerated ageing on the dimensional stability and detail reproduction of a facial silicone with different types of nanoparticle. A total of 60 specimens were fabricated with Silastic MDX 4-4210 silicone and they were divided into three groups: colourless and pigmented with nanoparticles (make-up powder and ceramic powder). Half of the specimens of each group were disinfected with Efferdent tablets and half with neutral soap for 60 days. Afterwards, all specimens were subjected to accelerated ageing. Both dimensional stability and detail reproduction tests were performed after specimen fabrication (initial period), after chemical disinfection, and after accelerated ageing periods (252, 504 and 1008 hours). The dimensional stability test was conducted using AutoCAD software, while detail reproduction was analysed using a stereoscope magnifying glass. Dimensional stability values were statistically evaluated by analysis of variance (ANOVA) followed by Tukey’s test (p < 0.01). Detail reproduction results were compared using a score. Chemical disinfection and also accelerated ageing affected the dimensional stability of the facial silicone with statistically significant results. The silicone’s detail reproduction was not affected by these two factors regardless of nanoparticle type, disinfection and accelerated ageing.

Influence of autoclave sterilization on dimensional stability and detail reproduction of 5 additional silicone impression materials

To evaluate the dimensional stability and detail reproduction of five additional silicone impression materials after autoclave sterilization. Impressions were made on the ISO 4823 standard mold containing several marking lines, in five kinds of additional silicone. All the impressions were sterilized by high temperature and pressure (135 °C, 212.8 kPa) for 25 min. Linear measurements of pre-sterilization and post-sterilization were made with a measuring microscope. Statistical analysis utilized single-factor analysis with pair-wise comparison of mean values when appropriate. Hypothesis testing was conducted at alpha = 0.05. No significant difference was found between the pre-sterilization and post-sterilization conditions for all locations, and all the absolute valuse of linear rate of change less than 8%. All the sterilization by the autoclave did not affect the surfuce detail reproduction of the 5 impression materials. The dimensional stability and detail reproduction of the five additional silicone impression materials in the study was unaffected by autoclave sterilization.

Evaluation of Outgassing, Tear Strength, and Detail Reproduction in Alginate Substitute Materials

To compare three alginate substitute materials to an alginate impression material for cast surface porosity (outgassing), tear strength, and detail reproduction. Detail reproduction tests were performed following American National Standards Institute/American Dental Association (ANSI/ADA) Specification No. 19. To measure tear strength, 12 samples of each material were made using a split mold, placed in a water bath until testing, and loaded in tension until failure at a rate of 500 mm/min using a universal testing machine. For cast surface porosity testing, five impressions of a Teflon mold with each material were placed in a water bath (37.8°C) for the in-mouth setting time and poured with vacuum-mixed Silky Rock die stone at 5, 10, 30, and 60 minutes from the start of mixing. The gypsum samples were analyzed with a digital microscope for surface porosity indicative of hydrogen gas release by comparing the surface obtained at each interval with four casts representing no, little, some, and significant porosity. Data analysis was performed using parametric and Kruskal-Wallis analysis of variance (ANOVA), Tukey/Kramer post-hoc tests (α=0.05), and individual Mann-Whitney U tests (α=0.0167). All alginate substitute materials passed the detail reproduction test. Tear strength of the alginate substitute materials was significantly better than alginate and formed three statistically different groups: AlgiNot had the lowest tear strength, Algin-X Ultra had the highest tear strength, and Position Penta Quick had intermediate tear strength. Significant variation in outgassing existed between materials and pouring times (p<0.05). All alginate substitute materials exhibited the least outgassing and cast porosity 60 minutes after mixing. Detail reproduction and tear strength of alginate substitute materials were superior to traditional alginate. The outgassing effect was minimal for most materials tested. Alginate substitute materials are superior replacements for irreversible hydrocolloid.

Transition dipole moments of charge transfer excitations in one-component molecular crystals

Owing to the peculiar structure of oligothiophene crystals, their low-energy b-polarized spectra are dominated by the contributions from charge transfer states almost free from Frenkel state admixtures, offering a unique opportunity for in-depth studies of the former. Here, a simple model, rooted in the Mulliken theory of charge transfer transitions, is proposed to estimate the relevant transition dipole moments. For sexithiophene, the resultant estimate agrees with the value used in the recent detailed theoretical reproduction of the absorption and electroabsorption spectra, and is found to be consistent with other input parameters. The approach presented here is readily applicable for other one-component molecular crystals, providing a simple method to estimate the intrinsic transition dipoles of charge transfer configurations.

Argumentative use of reported speech in British newspaper discourse

AbstractA reported utterance cannot be incorporated into the new discourse without undergoing certain transformations and losing some of its initial properties. Decision of representing or omitting information on certain aspects of the quoted utterance is not arbitrary, and this choice is subordinated to the writer's goals. In argumentative discourse the overall aim of convincing the addressee determines the way reported speech is presented to the readers. The present work analyzes those features of other discourses which are reproduced in argumentative discourse of the quality British press. Research revealed that of the six linguistic levels characterizing the initial utterance (phonetic, lexical, syntactic, semantic, pragmatic, and rhetorical), journalists choose only those relevant for the argumentative function the quotation performs. When reported speech is used as the thesis, the writer retains maximum control of the quotation by reproducing fewer levels, and focusing mainly on global semantics and pragmatics. When reported speech is used as an argument, the journalist, on the contrary, aims to show minimum control of the quoted utterance to increase its argumentative credibility. This is achieved by detailed reproduction of local semantics, lexica, and syntax of the quotation.

The effect of addition of calcium hypochlorite disinfectant on some physical and mechanical properties of dental stone

Background: The potentially damaging effects of the immersion technique, the difficulty in covering the entire surface of the cast with the spray disinfecting solution, and the inability to assume that every impression presented to the laboratory has been disinfected has led to the need for incorporating a disinfectant directly into the calcium sulfate hemihydrate. This study was designed to evaluate the effect of the addition of Calcium Hypochorite disinfectant on some physical and mechanical properties of the dental stone. Materials and methods: Calcium Hypochlorite disinfectant in aqueous solution in different concentrations 0.5, 1.0, 1.5 and 2.0% was added to type III dental stone. Setting time, setting expansion, reproduction of details, compatibility with impression materials and consistency are physical properties which were evaluated. The compressive strength and surface hardness as mechanical properties were also determined. Results: The results of this study showed that the addition of 1 % of calcium hypochlorite improved some of the physical and mechanical properties of dental stone (Setting Expansion, Compressive Strength and Surface Hardness) while its adversely affected the other properties (Setting Time) Conclusions: The 1 % of calcium hypochlorite disinfectant solution could be used to disinfect dental cast with the least effect when compared with the other concentrations of calcium hypochlorite .

Comparative Evaluation of Few Physical Properties of Epoxy Resin, Resin-Modified Gypsum and Conventional Type IV Gypsum Die Materials: An in vitro Study

To compare and evaluate few physical properties of epoxy resin, resin-modified gypsum and conventional type-IV gypsum die material. In the present study, dimensional accuracy, surface detail reproduction and transverse strength of three die materials like epoxy resin (Diemet-E), resin-modified gypsum (Synarock) and conventional type-IV gypsum (Ultrarock) are analyzed. For dimensional accuracy, master die (Bailey's die) is used and calibrations were made with digital microscope. For surface detail reproduction and transverse strength, rectangular stainless steel master die (Duke's die) was used and calibrations were made with Toolmaker's microscope and Instron universal testing machine respectively. One-way analysis of variance (ANOVA) was performed on the means and standard deviation for groups of each test. The results of the study showed statistically significant difference among these materials in dimensional accuracy, surface detail reproduction and transverse strength. Epoxy resin exhibited superiority in dimensional accuracy, surface detail reproduction and transverse strength and is nearest to the standards of accurate die material.

Surface detail reproduction and dimensional accuracy of stone models: influence of disinfectant solutions and alginate impression materials

This study compared the surface detail reproduction and dimensional accuracy of stone models obtained from molds disinfected with 2% sodium hypochlorite, 2% chlorhexidine digluconate or 0.2% peracetic acid to models produced using molds which were not disinfected, with 3 alginate materials (Cavex ColorChange, Hydrogum 5 and Jeltrate Plus). The molds were prepared over matrix containing 20-, 50-, and 75-µm lines, performed under pressure with perforated metal tray. The molds were removed following gelation and either disinfected (using one of the solutions by spraying followed by storage in closed jars for 15 min) or not disinfected. The samples were divided into 12 groups (n=5). Molds were filled with dental gypsum Durone IV and 1 h after the start of the stone mixing the models were separated from the tray. Surface detail reproduction and dimensional accuracy were evaluated using optical microscopy on the 50-µm line with 25 mm in length, in accordance with the ISO 1563 standard. The dimensional accuracy results (%) were subjected to ANOVA. The 50 µm-line was completely reproduced by all alginate impression materials regardless of the disinfection procedure. There was no statistically significant difference in the mean values of dimensional accuracy in combinations between disinfectant procedure and alginate impression material (p=0.2130) or for independent factors. The disinfectant solutions and alginate materials used in this study are no factors of choice regarding the surface detail reproduction and dimensional accuracy of stone models.

Kaon and pion femtoscopy at top RHIC energy in hydrokinetic model

The hydrokinetic model is applied to restore the initial conditions and space-time picture of the matter evolution in central Au + Au collisions at the top RHIC energy. The analysis is based on the detailed reproduction of the pion and kaon momentum spectra and femtoscopic data in whole interval of the transverse momenta studied by both STAR and PHENIX collaborations. A good description of the pion and kaon transverse momentum spectra and interferometry radii is reached with both initial energy density profiles motivated by the Glauber and Color Glass Condensate (CGC) models, however, at different energy densities.

Influence of Pigment and Opacifier on Dimensional Stability and Detail Reproduction of Maxillofacial Silicone Elastomer

We evaluated the influence of chemical disinfection and accelerated aging on the dimensional stability and detail reproduction of a silicone elastomer containing an opacifier and/or a pigment. A total of 120 samples were fabricated from Silastic MDX 4-4210 silicone and divided into groups (n = 10) according to pigment and/or opacifier (ceramic powder and/or barium sulfate) and disinfectant solution (neutral soap, Efferdent, or 4% chlorhexidine). The specimens were disinfected 3 times per week during 60 days and then subjected to accelerated aging for 1008 hours. Dimensional stability and detail reproduction tests were performed after specimens' fabrication (baseline) and chemical disinfection and periodically during accelerated aging (252, 504, and 1008 hours). The results were analyzed using 3-way repeated-measures analysis of variance and the Tukey Honestly Significant Difference test (a = 0.05). All groups exhibited dimensional changes over time. The disinfectant, pigment, and time (P < 0.0001) affected the dimensional stability of silicone. Statistically significant dimensional differences were not observed between the tested groups. Accelerated aging influenced the dimensional stability of the samples. All groups scored 2 in the detail reproduction tests, which represents the full reproduction of 3 test grooves with accurate angles. Incorporation of opacifier and/or pigment alters the dimensional stability of silicones used in facial prosthetics but seems to have no influence on detail reproduction. Accelerated aging is responsible for most of the dimensional changes in Silastic MDX4 4210, but all dimensional changes measured in this study remained within the limits of stability necessary for this application.

Model-Based Reproduction of Articulatory Trajectories for Consonant–Vowel Sequences

We present a novel quantitative model for the generation of articulatory trajectories based on the concept of sequential target approximation. The model was applied for the detailed reproduction of movements in repeated consonant-vowel syllables measured by electromagnetic articulography (EMA). The trajectories for the constrictor (lower lip, tongue tip, or tongue dorsum) and the jaw were reproduced. Thereby, we tested the following hypotheses about invariant properties of articulatory commands: (1) The target of the primary articulator for a consonant is invariant with respect to phonetic context, stress, and speaking rate. (2) Vowel targets are invariant with respect to speaking rate and stress. (3) The onsets of articulatory commands for the jaw and the constrictor are synchronized. Our results in terms of high-quality matches between observed and model-generated trajectories support these hypotheses. The findings of this study can be applied to the development of control models for articulatory speech synthesis.

Genome‐wide association mapping in Norwegian Red cattle identifies quantitative trait loci for fertility and milk production on BTA12

Reproductive performance is a critical trait in dairy cattle. Poor reproductive performance leads to prolonged calving intervals, higher culling rates and extra expenses related to multiple inseminations, veterinary treatments and replacements. Genetic gain for improved reproduction through traditional selection is often slow because of low heritability and negative correlations with production traits. Detection of DNA markers associated with improved reproductive performance through genome-wide association studies could lead to genetic gain that is more balanced between fertility and production. Norwegian Red cattle are well suited for such studies, as very large numbers of detailed reproduction records are available. We conducted a genome-wide association study for non-return rate, fertility treatments and retained placenta using almost 1 million records on these traits and 17 343 genome-wide single-nucleotide polymorphisms. Genotyping costs were minimized by genotyping the sires of the cows recorded and by using daughter averages as phenotypes. The genotyped sires were assigned to either a discovery or a validation population. Associations were only considered to be validated if they were significant in both groups. Strong associations were found and validated on chromosomes 1, 5, 8, 9, 11 and 12. Several of these were highly supported by findings in other studies. The most important result was an association for non-return rate in heifers in a region of BTA12 where several associations for milk production traits have previously been found. Subsequent fine-mapping verified the presence of a quantitative trait loci (QTL) having opposing effects on non-return rate and milk production at 18 Mb. The other reproduction QTL did not have pleiotropic effects on milk production, and these are therefore of considerable interest for use in marker-assisted selection.

Aggregation of Color Pigments by Surface Fixation Treatment

The quality of a printed image is strongly influenced by the physical and the chemical interactions between the ink and the paper. Print quality can be evaluated either by objective measure- ments using instruments or by visual assessment studies involving panel of observers judging the final print. In this article, the print qual- ity on commercial papers as well as on non-commercial papers with different amounts of salt for surface fixation has been studied. Per- ceived detail reproduction depends not only on sharp edge definition but also on the level of color saturation (Chroma). Color saturation and edge definition originate from two different ink and paper interac- tion processes. Color saturation is heavily dependent on ink penetra- tion while edge definition correlates to ink spreading. In order to gain understanding of the performance of surface treatment by salt, large efforts have been put on splitting up of the increase in color satura- tion (Chroma) and improved edge definition. The printouts have been made with a desktop printer using pigmented inks. Cross sec- tion images have been taken with a light microscope to analyze the ink penetration depth. SEM analysis has been made to analyze the aggregation of the pigments on the surface. The print quality meas- urements have been both objective measurements such as print density and subjective image evaluation using a test panel of observ- ers in a perceptual study. The perceptual study focused on detail reproduction, and efforts were made to separate the influence of the print density from the edge definition on the detail reproduction. The result from this study shows that an increased level of salt as surface fixation improves the detail reproduction due to aggregation of the pigments on the surface and that the ink penetration depth can be reduced by adding salt as surface fixation resulting in a higher print density. V C 2011 Society for Imaging Science and Technology.

An Effective Technique to Posterior Resin Composite Restorations

The aim of this study is to present a clinical case in which an occlusal matrix device was used in a patient who needed to restore a posterior tooth. A direct duplicate occlusal appliance was used (biteperf) in a patient who needed an occlusal restoration in two posterior teeth. Using the matrix helps having fast and accurate reproduction of the original anatomical details of the occlusal surface. The final result surprised with the presented restoration in terms of esthetic quality, despite the simplicity of the technique. Posterior teeth with initial lesions were confined to the occlusal surface of anatomically complex or fissured anatomy with or without signs of proximal caries wich are ideal candidates for this technique. The overlying enamel surface must be relatively intact; lesions of hidden or occult caries. The aesthetic and time-saving benefits of the occlusal device (biteperf) are immediately clear. The matrix allows the fast and accurate reproduction of the anatomic details of the original occlusal surface of the tooth. The professionals who lack an artistic penchant and marked manual ability will be able to carry out excellent posterior resin composite restorations.

Dimensional accuracy and detail reproduction of two hydrophilic vinyl polysiloxane impression materials tested under different conditions

A limitation of vinyl polysiloxane (VPS) impression materials is hydrophobicity, and manufacturers have added surfactants and labeled these new products as "hydrophilic." The purpose of this investigation was to evaluate and compare the dimensional accuracy and surface detail reproduction of two hydrophilic VPS impression materials under dry, moist, and wet conditions. Ten impressions were made under dry, moist, and wet conditions respectively, with monophase, and regular body VPS impression material using a stainless steel metal die similar to that described in American Dental Association (ADA) specification 19, with lines scribed on it. Dimensional accuracy was measured by comparing the average length of the middle horizontal line in each impression to the same line on the metal die, by using a measuring microscope. The surface detail was evaluated. A one-way analysis of variance and Student t-test were used to compare mean dimensional changes (α = 0.05). Conditions (dry, moist, and wet) did not cause significant adverse effects on the dimensional accuracy of either material. The mean dimensional changes were 0.00084% (+0.00041%) for monophase and 0.00119% (+0.00033%) for regular body. Monophase material was satisfactory in detail reproduction 100% of the time in dry conditions, 90% in moist, and only 20% in wet conditions. The regular body showed 100% satisfactory impressions in dry, 80% in moist, and 10% in wet conditions. With the additional smooth surface evaluation, only under dry conditions impressions with clinically acceptable surface quality were produced. Dimensional changes for both materials were well within ADA standards of minimal shrinkage value of 0.5%.

Semont's maneuver for treatment of benign paroxysmal positional vertigo

Along with Epley's canalith repositioning maneuver, the Semont maneuver is also recognized as an effective physical therapy for benign paroxysmal positional vertigo. However, the details of this maneuver are not well known, presumably because of the obscurity of the original description by Semont et al. In Japan, the “Semont liberatory maneuver,” as described by Brandt, is accepted as the “original” Semont maneuver. However, the two maneuvers are not identical. The aim of this paper was to reproduce the original procedure of Semont's as presented by A. Semont himself at the 10th Nagoya Otorhinolaryngological Forum held in Nagoya, Japan, in 2006. This lecture clarified some obscure points in the original paper; however, the procedure described at the forum was not a detailed reproduction of the original Semont maneuver, but was somewhat more complicated. Also of note, Semont decisively denied the cupulolithiasis theory and explained the usefulness of his maneuver according to the canalolithiasis theory.