Reduced Graphene Oxide Nanocomposites Research Articles

Eco-friendly Synthesis of Silver-Doped Reduced Graphene Oxide Nanocomposite, The Characterization, and Evaluation of Electrochemical Activity

In this study, Orobanche aegyptiaca Pers., which is an important holoparasite plant, was used for green synthesis of reduced graphene oxide silver nanocomposites (rGO-AgNCs). The obtained rGO-AgNCs were characterizated using UV–Vis spectroscopy, Fourier transformation infrared spectroscopy (FT-IR), X-Ray diffractiometer (XRD), Scanning electron microscope (SEM), Transmission electron microscope (TEM), and X-Ray photoelectron spectroscopy (XPS). The synthesized rGO-AgNCs structure were used to modify carbon paste electrode (rGO-AgNCs@CPE) for electrochemical determination of metronidazole (MNZ). It was observed that the obtained rGO-AgNCs@CPE showed higher sensitivity in MNZ determination than the unmodified CPE, and DPV measurements showed a low detection limit of 0.039 μM over a linear concentration range of 5–300 μM. Real sample analysis of the proposed sensor shows that it responds well in MNZ analysis of human urine.

Cu3(HHTP)2 decorated over rGO nanocomposites for flexible NH3 and H2S dual sensing at room temperature

Ammonia (NH3) and hydrogen sulfide (H2S) are both poisonous and corrosive gases, and thus timely detecting their leakage is thus required. Ideally, employing individual flexible sensor to simultaneously detect NH3 and H2S dual gases at room temperature could contribute to their miniaturization and integration, however, remains challenging. Here, flexible NH3 and H2S dual sensing at room temperature has been developed by utilizing Cu3(HHTP)2 decorated over reduced graphene oxide nanocomposites {Cu3(HHTP)2//rGO NCPs, HHTP=2,3,6,7,10,11-hexahydroxytriphenylene}, which have been synthesized via oxidation–reduction reaction of GO and Cu3(HHTP)2 metal–organic frameworks (MOFs). Typically, the Cu3(HHTP)2 MOFs are observed with spiny surface, and as-synthesized Cu3(HHTP)2//rGO NCPs present amorphous crystallization. Beneficially, Cu3(HHTP)2//rGO NCPs exhibit the NH3 and H2S dual sensing with the resistance-increasing response toward 10–50000 ppm NH3 and resistance-decreasing response to 0.1–20 ppm H2S. Further, the sensor prototype shows 40 days-long stability and 75 % high relative humidity tolerance, respectively. Remarkably, the ternary-NCPs show excellent flexibility, along with excellent sensing performance against various bending ways. Theoretically, rGO with high specific surface ratio and Cu3(HHTP)2 MOFs with enriched adoption sites might contribute to NH3 and H2S diffusion and adsorption. Practically, the simulation utilizing Cu3(HHTP)2//rGO NCPs to monitor H2S and NH3 has been conducted with reliable sensing.

Polyaniline/reduced graphene oxide nanocomposites for electrochemical and solar cell applications

Polyaniline nanocomposites are synthesized via in situ chemical oxidation method by reinforcing reduced graphene oxide nanoparticles of various weight percentage. Structural, optical, thermal and electrochemical studies are performed to know the significance of introducing reduced graphene oxide into polyaniline and to analyse the importance of filler weight percentage in determining various properties of the nanocomposites. X-ray diffraction peak intensity is appeared to be maximum for nanocomposite doped with 2% filler. This composite shows minimum crystallite size and maximum photoluminescence intensity. Maximum ID/IG ratio obtained for 2% filler added nanocomposite from Raman spectroscopy studies proved that the presence of more surface defects and recombination of charge carriers are the reasons for enhanced photoluminescence. Thermal stability is found to be better for a nanocomposite with 1% reduced graphene oxide and obtained a mass retention of 60% even after heating up-to 600 °C. SEM images give various shapes of nanocomposite such as nanorods, spherical nanoparticles and button shaped nanocomposites for different filler weight percentage. Carbon to oxygen ratio is observed to be decreased as the filler percentage increased from 1% to 4% in SEM-EDAX analysis. Polymer nanocomposite with 1% reinforcement possess maximum UV and visible absorption and is found to be decreased as filler concentration increased from 1 to 4%. Electrochemical analysis is performed for polyaniline and 1% reduced graphene oxide reinforced polyaniline nanocomposite. Specific capacitance of the electrode is obtained as 212 F g−1 and 609 F/g for polyaniline and nanocomposite respectively at a scan rate of 0.01 V/S. Solar cell device performance study shows that power conversion efficiency is 5.54% for 1% reduced graphene oxide nanocomposite, 4.7% for 2% reinforced, 4.16% for 3% filler and 3.61% for 4% nanocomposite.

In2O3 electrochemical transistors based on PtAu4/RGO nanocomposites functionalized gate for highly sensitive nitrite detection

Nitrite is commonly found in the environment, but its overuse and potential toxicity pose serious health risks. There is a strong need to develop robust and reliable methods for detecting nitrite. Herein, a novel In2O3 solution-gated electrochemical transistor (SGET) nitrite sensor was designed and fabricated for highly sensitive detection of nitrite. Different thicknesses of In2O3 thin films were prepared by sol–gel method, which were used as the channel of transistors and optimized through evaluating the electronic and electrochemical properties. To improve the catalytic oxidation of nitrite, PtAu4 nanoparticles modified reduced graphene oxide nanocomposites (PtAu4/RGO) were fabricated on the gate of transistors through electrodeposition approach. The developed sensor exhibited exceptional sensing performance in nitrite detection, which featured with low detection limit (0.1 nM nitrite) and ultra-wide linear range from 0.1 nM to 1 mM. The developed In2O3 SGET sensor displayed excellent stability and high resistance to common interfering ions, thereby demonstrating superior anti-interference performance. Nitrite in real samples of natural lake water has been accurately measured, suggesting that the designed sensor could act as an ideal transducer platform for highly sensitive and selective nitrite detection in food and environmental fields.

Palladium–reduced graphene oxide nanocomposites enhance neurite outgrowth and protect neurons from Ishemic stroke

Currently, the construction of novel biomimetic reduced graphene oxide (RGO)-based nanocomposites to induce neurite sprouting and repair the injured neurons represents a promising strategy in promoting neuronal development or treatment of cerebral anoxia or ischemia. Here, we present an effective method for constructing palladium-reduced graphene oxide (Pd-RGO) nanocomposites by covalently bonding Pd onto RGO surfaces to enhance neurite sprouting of cultured neurons. As described, the Pd-RGO nanocomposites exhibit the required physicochemical features for better biocompatibility without impacting cell viability. Primary neurons cultured on Pd-RGO nanocomposites had significantly increased number and length of neuronal processes, including both axons and dendrites, compared with the control. Western blotting showed that Pd-RGO nanocomposites improved the expression levels of growth associate protein-43 (GAP-43), as well as β-III tubulin, Tau-1, microtubule-associated protein-2 (MAP2), four proteins that are involved in regulating neurite sprouting and outgrowth. Importantly, Pd-RGO significantly promoted neurite length and complexity under oxygen-glucose deprivation/re-oxygenation (OGD/R) conditions, an in vitro cellular model of ischemic brain damage, that closely relates to neuronal GAP-43 expression. Furthermore, using the middle cerebral artery occlusion (MCAO) model in rats, we found Pd-RGO effectively reduced the infarct area, decreased neuronal apoptosis in the brain, and improved the rats’ behavioral outcomes after MCAO. Together, these results indicate the great potential of Pd-RGO nanocomposites as a novel excellent biomimetic material for neural interfacing that shed light on its applications in brain injuries.

Biosynthesis of microrubble-shaped nanoporous Co3O4/rGO NCs using leaves extract of Neolamarckia cadamba and its antibacterial/antioxidant performance

Nowadays, the whole globe is paying great attention for the sustainable development, eco-friendly and economical production of nanostructures materials. With this motivation, the present work portrayed one-step ‘in-situ’ bioinspired green fabrication of Co3O4–reduced graphene oxide nanocomposites (Co3O4–rGO NCs) for the first time utilizing an aqueous leaf extract of Neolamarckia cadamba. As-fabricated NCs were characterized by several analytical and electron microscopic techniques viz. X-ray diffraction (XRD), Fourier Transform-Infrared (FT-IR), Energy dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), BET (Brunauer-Emmett-Teller), Scanning electron microscopy (SEM), and Transmission electron microscopy (TEM) to evaluate their phases, structure, shape, composition, chemical state, porosity, optical and morphological aspects. The XRD study revealed a cubic spinel symmetry of NCs, while crystallite size estimated around 25 nm. TEM spectroscopy exposed an average particle size 8–10 nm of Co3O4 grown on the surface of reduced graphene oxide (rGO NCs), whereas SEM analysis showed sharped microrubble-shaped morphology. The formation of NCs by doping metal oxide with rGO through in-situ method were confirmed by XRD, EDS, Raman, and XPS spectroscopy. The BET study estimated the specific surface area and pore size of NCs as 98 m2/g and 8.9 nm respectively. The Co3O4–rGO NCs demonstrated an effective bactericidal activity against S. aureus, E. coli, K. pneumoniae, and B. subtillis. Prominently it was found that, a significant antibacterial activity seen against E. coli and S. aureus at a concentration 0.1 mg/100 µL may be due to scaffold morphology, nanoscale-structures and nanoporosity of the NCs. Due to receiving significant antibacterial activity, material’s molecular docking was assessed. Furthermore, an antioxidant activity of leaf extract and NCs was evaluated by DPPH method. An outstanding biological study of bioinspired NCs revealed that material could be used as a potent antimicrobial agent.

Boosting the tribological properties by developing a g-C3N4/RGO nanocomposite as lubricant additive

Herein, the graphitic carbon nitride (g-C3N4) nanosheets are protonated treatment and then electrostatically self-assembled with reduced graphene oxide (RGO) to obtain g-C3N4/RGO nanocomposite. When employed as a lubricant additive, the amino groups in g-C3N4 can accelerate the formation of friction films, while the cataclastic RGO nanosheets can repair worn surface and reduce wear. Meanwhile, the weak interaction between g-C3N4 and RGO sheets possesses low shear stress, producing interlayer slip, which can effectively reduce friction and anti-wear. As expected, the coefficient of friction (COF) of 0.103 and the wear volume of 0.86 × 105 μm3 for the lubricant containing 2.0 wt% g-C3N4/RGO are 62.3 % and 96.0 % lower than PAO-10 base oil, respectively.

Samarium-doped vanadium pentoxide nanorods anchored reduced graphene oxide nanocomposite as a bi-functional electrode material for supercapacitor and direct methanol oxidation fuel cell applications

In this work, we demonstrate a novel, facile synthesis of reduced graphene oxide nanosheets decorated samarium-doped vanadium pentoxide (RGO/Sm:V2O5) nanocomposite material and explore its application toward supercapacitor and direct methanol oxidation process. As-fabricated material and electrode were well-characterized to evaluate its surface morphology and functionalities. Results indicate a maximum capacitance value of 544 F/g for RGO/Sm:V2O5 modified electrode than the 2% Sm:V2O5 (346 F/g) and V2O5 (133 F/g) modified electrodes. In addition, an excellent Rct value (3.2 Ω) was achieved for the RGO-loaded Sm:V2O5 electrode than the 2% Sm:V2O5 electrode (4.7Ω). The RGO/Sm:V2O5 electrode also shows higher cyclic efficiency (98 %) at the 1000th cycle than the non-RGO loaded Sm:V2O5 electrodes. Furthermore, the fabricated electrodes were also examined for the direct methanol oxidation performances, and the results indicate a higher current density value of 181 mA/cm2 for RGO/Sm:V2O5 electrode than 2% Sm:V2O5 electrode (139 mA/cm2). The excellent electrochemical performance of the RGO/Sm: V2O5 electrode is mainly due to the presence of RGO nanosheet in the synthesized nanocomposite material. Therefore, as-prepared material can be applied as an excellent alternative electrode material for energy storage and conversion systems.

Two-photon absorption induced optical limiting action of Ag-doped lanthanum molybdate decorated reduced graphene oxide nanocomposites

In this research, we aimed to investigate the linear and non-linear optical properties of Ag-La2(MoO4)3@RGO nanocomposites. For this purpose, Graphene Oxide (GO) was synthesized by Modified Hummer’s method after which GO was chemically reduced to Reduced graphene oxide (RGO). The nanocomposite Ag-doped La2(MoO4)3 is prepared by a simple and facile co-precipitation method. The prepared nanocomposite was characterized by Fourier transform infrared (FTIR), Ultraviolet-Visible (UV-Vis) absorption, X-ray diffraction (XRD), Scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDX). XRD and EDX analysis indicated the reduction of GO and successful synthesis of Ag-doped La2(MoO4)3 nanocomposite. FESEM images portray the presence of thin layers of graphene sheets and Ag-doped La2(MoO4)3 on the sheets of reduced graphene oxide. Ground state absorption studies show that the reduction of graphene oxide causes a hypsochromic shift in the absorption maxima of the graphene layers. The photoluminescence of Ag- La2(MoO4)3@RGO demonstrates the utmost emission in the UV range caused by the valence band and conduction band's direct transitions in the band gap region. Z-scan method using Nd: YAG laser exposes that both nanocomposite and specific counterparts hold reverse saturable absorption behaviour. The source of optical limiting action is attributed to the excited state absorption process, emerging from the influence of the plasmon resonance state of Ag nanoparticles. Strong nonlinear absorption and lower onset limiting threshold make the Ag-La2(MoO4)3@RGO nanocomposite desirable material for laser safety devices.

Designing the redox activity of CuMoO4 electrodes on N-rich reduced graphene oxide nanocomposite for high performance supercapacitor

In this investigation, environmentally friendly supercapacitor electrode materials of CuMoO4 coated on nitrogen-doped reduced graphene oxide (CMO/NRGO) nanocomposite were fabricated using a low-cost hydrothermal method. This supercapacitor has currently attracted devices and long-time stability. The electrochemical behavior of the system was investigated with working electrodes coated on Ni foam substrate in a 6 M KOH electrolyte. The findings revealed substantial advancements in specific capacitance for the fabricated electrode, attaining a value of 629.6 F g−1 at 1 A g−1. An asymmetric capacitor was fabricated by using CMO/NRGO (CuMoO4/N doped rGO) and activated carbon (AC). It design enables the hybrid capacitor to attain a balance between EDLC and PC characteristics, making it suitable for applications requiring both efficient energy storage and rapid charge/discharge capabilities. In 1.4 voltage range, an asymmetric capacitor shows good energy and power (42.85 Wh kg−1 at 580.36 W kg−1) density. After 6000 cycles, it retains 87.2 % of capacitance value. The obtained results suggest that CMO/NRGO electrode exhibits significant for developing the effective and long-lasting energy storage systems.

Hybrid 1D titanium oxide nanowire – Reduced graphene oxide nanocomposites as efficient catalyst support for PEMFC

With hydrogen being projected as the fuel of the future, proton exchange membrane fuel cells (PEMFC) have regained prominence as a zero-emission power source. Researchers are focusing on replacing the conventional carbon support used for the platinum catalysts with alternative materials to improve the durability of the electrocatalysts. Despite being a potential candidate, graphene-based materials have been limited by their lower limiting current density, possibly due to restacking of the graphene sheets. On this note, we introduced varying quantities of metal-oxide based 1D TiO2 nanowires to reduced graphene oxide (rGO) support and analysed their impact on the performance of the electrocatalyst. The optimized support with an initial content of 60 wt.% GO and 40 wt.% TiO2 exhibited higher mass transfer limiting current density, after Pt incorporation (Pt/TiO2-rGO), in comparison to the other composites. The catalyst showed higher retention in electrochemical surface area (1.42 times) and mass activity (1.48 times) compared to the commercial Pt/C after an accelerated durability test. Polarization studies carried out in a 25 cm2 fuel cell fixture exhibited a peak power density close to 720 mW cm−2 and almost two times higher current density (at 0.6 V) than the catalyst without TiO2. These results reaffirm the role of TiO2 in overcoming the limitations of graphene-based support.

A green approach to synthesis of Ag-doped CeO2 nanorods embedded reduced graphene oxide nanocomposite for excellent photocatalytic and antimicrobial activity

In this paper, the Ag-doped cerium oxide nanorods embedded reduced graphene oxide (Ag@CeO2/rGO) nanocomposite was synthesized via Punica Granatum peel extract for for photocatalytic degradation of methylene blue (MB) and 4-nitrophenol (4-NP). The microstructural results confirmed the successful decoration of Ag-doped CeO2 nanorods on rGO matrix. The photocatalytic properties, including photocatalytic degradation, charge transfer kinetics and photocurrent generation, are systematically investigated using electrochemical impedance spectroscopy (EIS), photocurrent transient response (PCTR) and open circuit voltage decay (OCVD). The results of photocatalytic dye degradation measurements indicated that Ag@CeO2/rGO nanocomposite is more effective than pristine CeO2 to degrade the MB dye, and the degradation rate reached 100 % in 60 min. The decomposition of MB with Ag@CeO2/rGO nanostructure followed first-order reaction kinetics with a reaction rate constant (Ka) of 0.0198 min−1. The EIS and OCVD measurements revealed that the Ag doping and incorporation of rGO could suppress the recombination probability in CeO2 by the separation of photo-generated electron–hole pairs, which leads to the enhanced photocurrent generation and photocatalytic activity. The photocurrent density of Ag@CeO2/rGO, CeO2/rGO and pristine CeO2 are 215, 167.4 and 98.8 mAcm−2, respectively.

Ag-doped CuO nanoparticles embedded reduced graphene oxide nanocomposite from Punica granatum peel extract and evaluation of their photocatalytic activity and antimicrobial potential

The present study explored Punica granatum peel extract as a reducing and capping agent for synthesis of Ag-doped CuO nanoparticles embedded reduced graphene oxide (rGO) nanocomposite. The crystalline nature of the Ag doped CuO/rGO was identified utilizing X-ray diffraction (XRD) analysis. The surface morphology of Ag doped CuO/rGO was investigated by Scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. The surface elemental composition of the prepared material was investigated by the Energy dispersive spectra (EDS) analysis. Ag resulted in enhanced absorbance in the visible range as well as a reduction in band gap energy. The catalytic activity of the green synthesized Ag doped CuO/rGO photocataltyst was evaluated in the reduction of organic pollutants such as 4-nitrophenol (4-NP) and methylene blue (MB) in water at mild conditions. The results indicated that the biosynthesized Ag-CuO/rGO composites have very high and effective catalytic activity over MB dye (99.5 %), high rate constant (0.9871 min−1) and long term stability with 60 min irradiation of UV light. In addition, initial process parameters of catalyst dosage and MB concentration, and pH of the solution were also examined. Differential antimicrobial effects of doped and undoped CuO nanoparticles (NPs) against selected strains of bacteria and fungi were confirmed.

Synthesis and Characterization of Palladium/Silver Modified Reduced Graphene Oxide–Nanocomposite Platform for Electrochemical Sensors

AbstractMetal nanoparticles incorporated into carbon nanostructures have tremendous applications in the field of nanosensors and other technologies. Herein, a nanohybrid of reduced graphene oxide modified with silver and/or palladium nanoparticles (Ag/Pd/rGO) was prepared by impregnation of Pd and Ag into the rGO platform and deposited on a glass carbon electrode. Palladium and silver nanoparticles improve the stability and durability of the sensor platform by preventing the agglomeration of graphene oxide sheets and providing chemical stability against environmental factors. This ensures long‐term reliability and repeatability of the sensor performance. The morphologies and microstructures of the as‐prepared nanohybrid were characterized by X‐ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, UV–visible and infrared spectroscopy. The average crystallite size of PdAgNPs was found to be between 12 and 15 nm and demonstrated good dispersion across reduced graphene oxide sheets with high‐loading capacities. Thorough investigation of the electrochemical properties of the nanomaterial surfaces through cyclic voltammetry (CV) experiments, revealed distinct redox peaks for Ag+/Ag0 and Pd2+/Pd0 processes and demonstrated the excellent electrochemical properties of the prepared nanocomposites. The rGO‐PdAgNPs‐GCE had a diffusion coefficient value of 1.14×10−14 cm2 s−1 which is acceptable for electrochemical sensors as it is indicative of a fast response time and enhanced sensitivity to changes in gas concentration. The results obtained through thorough characterizations contributes to the novelty of the research by offering a deeper understanding of the material properties and the potential of the nanohybrid material for a broad application scope.

Synthesis of Niobium Pentoxide and Its Reduced Graphene Oxide Nanocomposite for Enhanced Supercapacitor Applications

Synthesis of Niobium Pentoxide and Its Reduced Graphene Oxide Nanocomposite for Enhanced Supercapacitor Applications

Cytosine-Rich Oligonucleotide and Electrochemically Reduced Graphene Oxide Nanocomposite for Ultrasensitive Electrochemical Ag+ Sensing.

Silver ions (Ag+) are crucial in various fields, but pose environmental and health risks at high concentrations. This study presents a straightforward approach for the ultra-trace detection of Ag+, utilizing a composite of a cytosine-rich oligonucleotide (CRO) and an electrochemically reduced graphene oxide (ERGO). Initially, ERGO was synthesized on a glassy carbon electrode (GCE) through the reduction of graphene oxide (GO) via cyclic voltammetry. A methylene blue-tagged CRO (MB-CRO) was then anchored to the ERGO surface through π-π interactions, resulting in the formation of an MB-CRO-modified ERGO electrode (MB-CRO/ERGO-GCE). The interaction with Ag+ ions induced the formation of silver-mediated C-Ag+-C coordination, prompting the MB-CRO to adopt a hairpin structure. This conformational change led to the desorption of the MB-CRO from the ERGO-GCE, causing a variation in the redox current of the methylene blue associated with the MB-CRO. Electrochemical assays revealed that the sensor exhibits extraordinary sensitivity to Ag+ ions, with a linear detection range from 1 femtomolar (fM) to 100 nanomolars (nM) and a detection limit of 0.83 fM. Moreover, the sensor demonstrated high selectivity for Ag+ ions and several other benefits, including stability, reproducibility, and straightforward fabrication and operational procedures. Additionally, real sample analyses were performed using the modified electrode to detect Ag+ in tap and pond water samples, yielding satisfactory recovery rates.

One-Pot Synthesis of Alkyl Functionalized Reduced Graphene Oxide Nanocomposites as the Lubrication Additive Enabling Enhanced Tribological Performance.

Recently, aiming for the enhanced dispersibility of graphene-based nanomaterials in lubricating oil matrices to serve as highly efficient lubricant additives, numerous modification approaches have been extensively studied. However, these previous modification routes usually involve a tedious multistep modification process or multitudinous toxic reagents, restricting their extensive practical application. In this work, novel graphene oxide (GO) nanoadditives (RGO-g-BO) featuring excellent durable dispersion capability and remarkable tribological performance were successfully prepared via an environmentally friendly one-step approach consisting of surface grafting of long-chain bromooctadecane (BO) and in situ chemical reduction. Benefiting from the greatly improved lipophilicity (resulting from the introduction of hydrophobic long-chain alkane groups and chemical reduction), along with the miniaturization effect, RGO-g-BO exhibits superior long-term dispersion stability in the finished oil. Moreover, the tribological properties results demonstrated that the finished oil filled with RGO-g-BO nanolubricants achieved an outstanding friction-reducing and antiwear performance. Particularly, under the optimum content of RGO-g-BO (as low as 0.005 wt%), the friction coefficient as well as the wear volume of the composite finished oil were greatly reduced by 13% and 53%, respectively, as compared with nascent finished oil. Therefore, in view of the advantages of low-cost, one-step facile synthesis, desirable dispersion capability, and remarkable tribological performance, RGO-g-BO holds great prospects as a highly efficient lubrication additive in the tribology field.

Polythiophene/nitrogen-doped reduced graphene oxide nanocomposite as a hybrid supercapacitor electrode

In this study polythiophene/nitrogen-doped reduced graphene oxide (Pth/n-rGO) was synthesized by in situ chemical polymerization. The correct synthesis of Pth/n-rGO nanocomposite was checked and confirmed through different spectral, elemental and morphological analysis. The supercapacitor performance of the Pth/n-rGO was higher than those of pure Pth and n-rGO in a neutral medium containing 1 M sodium sulfate. The highest energy density, specific capacitance, and power density values of 13.1 Wh kg−1, 455 F g−1, and 279 W kg−1 were achieved for the Pth/n-rGO nanocomposite. The Pth/n-rGO electrode also revealed commendable cyclic stability which it maintained 94% of its original specific capacitance and 125% coulombic efficiency during 1500 galvanostatic charge-discharge cycles. The superior charge-storage property of Pth/n-rGO is ascribed to the double-layer/pseudocapacitance charge storage synergistic effect. By considering the results of performance and stability for the Pth/n-rGO nanocomposite in this study, it could be good candidate for development of new supercapacitors electrode material.

Evaluation of Electrochemical and Antimicrobial Efficacy of Green Synthesized Silver Functionalized Reduced Graphene Oxide Nanocomposites

Evaluation of Electrochemical and Antimicrobial Efficacy of Green Synthesized Silver Functionalized Reduced Graphene Oxide Nanocomposites

Biocompatible adipose extracellular matrix and reduced graphene oxide nanocomposite for tissue engineering applications

Despite the immense need for effective treatment of spinal cord injury (SCI), no successful repair strategy has yet been clinically implemented. Multifunctional biomaterials, based on porcine adipose tissue-derived extracellular matrix (adECM) and reduced graphene oxide (rGO), were recently shown to stimulate in vitro neural stem cell growth and differentiation. Nevertheless, their functional performance in clinically more relevant in vivo conditions remains largely unknown. Before clinical application of these adECM-rGO nanocomposites can be considered, a rigorous assessment of the cytotoxicity and biocompatibility of these biomaterials is required. For instance, xenogeneic adECM scaffolds could still harbour potential immunogenicity following decellularization. In addition, the toxicity of rGO has been studied before, yet often in experimental settings that do not bear relevance to regenerative medicine. Therefore, the present study aimed to assess both the in vitro as well as in vivo safety of adECM and adECM-rGO scaffolds. First, pulmonary, renal and hepato-cytotoxicity as well as macrophage polarization studies showed that scaffolds were benign invitro. Then, a laminectomy was performed at the 10th thoracic vertebra, and scaffolds were implanted directly contacting the spinal cord. For a total duration of 6 weeks, animal welfare was not negatively affected. Histological analysis demonstrated the degradation of adECM scaffolds and subsequent tissue remodeling. Graphene-based scaffolds showed a very limited fibrous encapsulation, while rGO sheets were engulfed by foreign body giant cells. Furthermore, all scaffolds were infiltrated by macrophages, which were largely polarized towards a pro-regenerative phenotype. Lastly, organ-specific histopathology and biochemical analysis of blood did not reveal any adverse effects. In summary, both adECM and adECM-rGO implants were biocompatible upon laminectomy while establishing a pro-regenerative microenvironment, which justifies further research on their therapeutic potential for treatment of SCI.