Reconfigurable Array Research Articles

PV Array Reconfiguration for Global Maximum Power Optimizing under Partial Shading Conditions based on PV Switched System

Background: Due to the partial shading effects on different photovoltaic (PV) modules in a PV array, PV module operating conditions are inconsistent, and PV array output power is significantly reduced. Although the maximum power point (MPP) of a non-uniform irradiance PV array can be observed through global maximum power point tracking (GMPPT), no evaluation of the array's energy potential has been done. Objective: One of the most effective solutions to overcome the negative effects of partial shading in PV systems is the PV array reconfiguration process. To optimize the electrical structure of the PV array as the PV modules are partially shaded in a non-uniform manner, this study proposes a promising technique for dynamic reconfiguring a PV array in order to improve the extracted maximum power from a PV array under partial shading conditions (PSC). Methods: PV modules are rearranged by iteratively sorting them to allow the PV array with nonuniform irradiance to produce as much power as possible. This is conducted by applying a switching matrix to implement a PV-switched system approach. The proposed system with different PV array dimensions (e.g., 3×4, 4×6, and 5×8) is assessed in order to validate the proposed algorithm. A MATLAB/Simulink PV array developed model is used to find the global maximum power point for the different PV array dimensions in both pre-reconfiguration and post-reconfiguration states. Results: A detailed numerical comparison of the extracted power from the proposed system has been provided. Conclusion: The results show that the proposed system has the potential to extract the exact global maximum power for a PV-switched system under PSC, irrespective of array dimensions, according to simulation results.

Ultrasensitive dim-light neuromorphic vision sensing via momentum-conserved reconfigurable van der Waals heterostructure

Reconfigurable phototransistors featuring bipolar photoresponses are favorable for manipulating high-performance neuromorphic vision sensory. Here, we present a momentum-conserved reconfigurable phototransistor based on the van der Waals heterojunction between methylammonium lead iodide perovskite and two-dimensional Bi2O2Se semiconductor, which exhibits a synergistic interplay of interband hot-carrier transitions and reconfigurable heterointerface band alignments, eventually achieving the ultrahigh bipolar optoelectronic performances with the photoresponsivity of 6×107 AW−1, accompanied by the specific detectivity of 5.2×1011 Jones, and the dynamic range of 110 dB. Moreover, A 3×3 heterotransistor array is fabricated to perform in-sensor analog multiply-accumulate operations even under the challenging dim illumination of 0.1 μWcm−2 that comparable to natural moonlight. The reconfigurable heterotransistor array can be further adopted to enhance the traffic-light detection under dim-light conditions. Our advancement in momentum-conserved reconfigurable heterotransistor signifies a leap forward in real-time, energy-efficient, and low-light image processing for neuromorphic vision sensors.

Reconfigurable dielectric resonator antenna and array with frequency and polarization flexibility

To implement frequency and polarization hybrid reconfiguration, a 4 × 4 array has been investigated. The radiation elements of the antenna array consist of cylindrical dielectric resonators, Wilkinson power divider, PIN diode, and dielectric substrate. The PIN diode controls the states of each branch in the Wilkinson power divider to achieve frequency and polarization reconfigurability. To verify the feasibility of the design, a fabricated sample of the proposed antenna array has been measured. The results demonstrate that the antenna array can be switched freely between its operating frequencies and polarizations. It operates within a bandwidth of 1.93 to 4.6 GHz for frequency reconfiguration, and three common polarization states—linear polarization, left-handed circular polarization, and right-handed circular polarization—can be continuously tuned from 2.96 to 3.39 GHz.

FlowCert: Translation Validation for Asynchronous Dataflow via Dynamic Fractional Permissions

Coarse-grained reconfigurable arrays (CGRAs) have gained attention in recent years due to their promising power efficiency compared to traditional von Neumann architectures. To program these architectures using ordinary languages such as C, a dataflow compiler must transform the original sequential, imperative program into an equivalent dataflow graph, composed of dataflow operators running in parallel. This transformation is challenging since the asynchronous nature of dataflow graphs allows out-of-order execution of operators, leading to behaviors not present in the original imperative programs. We address this challenge by developing a translation validation technique for dataflow compilers to ensure that the dataflow program has the same behavior as the original imperative program on all possible inputs and schedules of execution. We apply this method to a state-of-the-art dataflow compiler targeting the RipTide CGRA architecture. Our tool uncovers 8 compiler bugs where the compiler outputs incorrect dataflow graphs, including a data race that is otherwise hard to discover via testing. After repairing these bugs, our tool verifies the correct compilation of all programs in the RipTide benchmark suite.

FPGA-based measurements of the relative arrival time of a high-repetition rate, quasi-cw fourth generation light source.

In this paper, we demonstrate the successful implementation of reconfigurable field-programmable gate array technology into a pulse-resolved data acquisition system to achieve a femtosecond temporal resolution in ultrafast pump-probe experiments in real-time at large scale facilities. As proof of concept, electro-optic sampling of terahertz waveforms radiated by a superradiant emitter of a quasi-cw accelerator operating at a 50kHz repetition rate and probed by an external laser system is performed. Options for up-scaling the developed technique to a MHz range of repetition rates are discussed.

Hardware Acceleration for High-Volume Operations of CRYSTALS-Kyber and CRYSTALS-Dilithium

Many high-demand digital services need to perform several cryptographic operations, such as key exchange or security credentialing, in a concise amount of time. In turn, the security of some of these cryptographic schemes is threatened by advances in quantum computing, as quantum computer could break their security in the near future. Post-quantum cryptography (PQC) is an emerging field that studies cryptographic algorithms that resist such attacks. The National Institute of Standards and Technology (NIST) has selected the CRYSTALS-Kyber Key Encapsulation Mechanism and the CRYSTALS-Dilithium Digital Signature algorithm as primary PQC standards. In this article, we present field-programmable gate array (FPGA)-based hardware accelerators for high-volume operations of both schemes. We apply high-level synthesis (HLS) for hardware optimization, leveraging a batch processing approach to maximize the memory throughput and applying custom HLS logic to specific algorithmic components. Using reconfigurable FPGAs, we show that our hardware accelerators achieve speedups between 3 \(\times\) and 9 \(\times\) over software baseline implementations, even over ones leveraging CPU vector architectures. Furthermore, the methods used in this study can also be extended to the new CRYSTALS-based NIST FIPS drafts, ML-KEM and ML-DSA, with similar acceleration results.

On-line Configuration Identification and Control of Modular Reconfigurable Flight Array

With the increasing complexity of the working environment and the diversification of mission requirements of UAVs, traditional UAVs have a fixed structure and single function. It is difficult to be applied in occasions with complex environments and changing load demands. The modular reconfigurable flight array (MRFA) is composed of no less than four isomorphic unit modules that are freely spliced together. By adding or removing flight unit modules and adjusting the arrangement of flight unit modules, the configuration of the MRFA can be changed, so that it can adapt to complex environments and then complete different flight missions. In the process of MRFA research and development, online configuration identification has become one of important problem to be solved. In this paper, a configuration recognition algorithm is designed based on the breadth-first searching method to identify the online structure of MRFA firstly. Then, the dynamic model of the aircraft is carried out according to the obtained configuration information. At the same time, the mathematical model and configuration information of the MRFA are combined to establish an optimization control allocation mechanism to allocate suitable rotational speed for multiple rotors. Finally, several examples are carried out to show that the proposed technology can recognize the configuration with 100% recognition rate and average online recognition time 569.4ms. Then a cascade PID controller is designed to realize the flight control of the irregular MRFA with faster tracking performance of no more than 40 seconds.

Rotation-invariant image recognition using interconnected floating-gate phototransistor

Rotational invariance is fundamental for robust image recognition systems, ensuring accurate analysis irrespective of image orientation. However, existing systems predominantly reliant on software often encounter challenges such as increased computational demands and compromises between processing speed and accuracy. In this study, we propose leveraging the interconnected floating-gate (FG) structure as an effective hardware-level solution to achieve rotational invariance in image recognition. Our design features a reconfigurable two-dimensional material FG phototransistor array, where each processing unit integrates four sensory devices sharing a common FG. This configuration facilitates uniform distribution of stored charges across the interconnected FG layer, which is typically made of metal, enabling consistent application of a single weight matrix to images across varied rotational conditions. The photoactive material, tungsten diselenide (WSe2), possesses a distinctive bipolar property that facilitates both hole and electron tunneling into the FG layer. This property directly contributes to the efficiency of state transition within the setup and improves its overall adaptability. In this manner, our design achieves stable and predictable outputs in recognizing identical digital numbers regardless of their rotation, while also demonstrating variable performance essential for accurately distinguishing between different digital numbers. This dual capability guarantees both the adaptability and precision required for rotation-invariant image recognition, suggesting that our work may open up a promising venue for exploring advanced hardware designs, such as optimized interconnected FG architectures, tailored for enhancing recognition accuracy and efficiency in the field of intelligent visual systems.

Design of high performances electronically reconfigurable antenna arrays by means of parasitic structures and RF-MEMS switches

AbstractThis work explores the development of smart array antennas, able to electronically change their beam patterns through reconfigurable linear, planar, or conformal parasitic structures controlled by mean of a set of electronic switches namely the radio frequency micro-electromechanical switches (RF-MEMS). The motivation of this study is to extend and make competitive the use of reconfigurable antenna arrays in areas such as the Internet of Things (IoT) and wireless sensor networks. These hot research areas require a capillary distribution of sensors characterized by compact dimensions and limited cost. The radiating systems play a key role in such applications since the improvement of the radiating properties can dramatically reduce the power consumption of such sensors and extend their operative range. Standard smart antenna arrays such as phased, or fully adaptive arrays are extremely expensive, expensive and difficult to control. In this work, the use of smart reconfigurable antenna arrays that do not require expensive digital variable phase shifters and attenuators has been considered. The proposed antenna structures are based on reconfigurable parasitic structures, that thanks to suitable RF-MEMs switches are able to obtain a desired beam pattern, by steering the main beam in a given direction, removing eventually interfering signals and maximizing the signal-to-noise ratio SNR. The versatility, simplicity, and low cost of such antennas make them particularly suitable for the emergent wireless sensor networks and IoT applications. Theoretical background, design guidelines, and suggestions for their fabrication are detailed in this work. Some antenna models for different practical applications are designed, optimized, numerically assessed with commercial electromagnetic simulators, and commented to provide a valid alternative to researchers involved in antenna design for IoT applications.

Miniaturized Hyperspectral Imager Utilizing a Reconfigurable Filter Array for Both High Spatial and Spectral Resolutions.

Miniaturized hyperspectral imaging based on filter arrays has attracted much attention in consumer applications, such as food safety and biomedical applications. In this Letter, we demonstrate a miniaturized hyperspectral imager using a reconfigurable filter array to tackle the existing trade-off issue between the spectral and spatial resolutions. Utilizing tens of intermediate states of a vanadium dioxide cavity, we increase the total number of physical spectral channels by tens of times from a 2 × 2 mosaic filter unit, providing both high spatial and spectral resolutions for spectral imaging. The reconfigurable filter has a good spectral resolvability of 10 nm in the visible range with a wavelength inaccuracy of less than 2.1 nm. Hyperspectral imaging is demonstrated with a frame rate of 4.5 Hz.

A reconfigurable ultra-wideband high-purity multimode terahertz OAM antenna array based on graphene and vanadium dioxide

A reconfigurable ultra-wideband multimode terahertz OAM antenna array based on graphene and vanadium dioxide (VO2) is presented in this paper. The uniform circular array (UCA) composed of circularly polarized (CP) antennas, which include a ring radiation patch, a parasitic patch, a perovskite substrate and an irregular VO2 ground plane. The radiation patch is covered with a layer of graphene, by changing the chemical potential of graphene, the working bandwidth and axial ratio bandwidth of the antenna can be changed. By changing the phase state of VO2 (metal state / insulation state) to control the working state of the antenna. The impedance bandwidth (IBW) of the CP antenna proposed is 115.09% (1.73–6.42 THz), the axial ratio bandwidth (ARBW) is 43.97% (2.36–3.69 THz). Using the CP antenna unit can simplify the complex feed network, and only feeding the equal amplitude and equal phase excitation can realize the vortex wave. Changing the number and rotation angle of the antenna unit can realize multimode vortex waves with the l= 0, ±1, ±2, ±3, the purity is approximately 1, respectively. The proposed UCA has excellent application prospect in the 6G communication.

Research on PV array reconstruction and Full-cycle maximum power point tracking technology of space solar power station

Space solar power station is an energy system that converts solar energy into electrical energy in the space environment and then transmits it to the space platform or ground using wireless power transmission technology. To improve the power generation and system efficiency of the space solar power station, an adaptive and reconfigurable photovoltaic array with multi-configuration is proposed, which can avoid large attenuation of the output power and efficiency of the photovoltaic array when the photovoltaic modules have a fault occurs or the receive different irradiation intensity. Then, according to the orbit area and light condition of the space solar power station, the operation mode are divided in detail. Furthermore, a novel full-cycle and multi-mode GMPPT (maximum power point tracking) strategy is proposed. Compared to the single mode MPPT, the control strategy has shorter response time, faster convergence and higher tracking accuracy. Through the above research, the output power and photoelectric conversion efficiency of space solar power station can be significantly improved.

Optimizing biphoton generation via reconfigurable nonlinear waveguide arrays based on scattering tensor

Optimizing biphoton generation via reconfigurable nonlinear waveguide arrays based on scattering tensor

Field-Programmable Gate Array Architecture for the Discrete Orthonormal Stockwell Transform (DOST) Hardware Implementation

Time–frequency analysis is critical in studying linear and non-linear signals that exhibit variations across both time and frequency domains. Such analysis not only facilitates the identification of transient events and extraction of key features but also aids in displaying signal properties and pattern recognition. Recently, the Discrete Orthonormal Stockwell Transform (DOST) has become increasingly utilized in many specialized signal processing tasks. Given its growing importance, this work proposes a reconfigurable field-programmable gate array (FPGA) architecture designed to efficiently implement the DOST algorithm on cost-effective FPGA chips. An accompanying MATLAB app enables the automatic configuration of the DOST method for varying sizes (64, 128, 256, 512, and 1024 points). For the implementation, a Cyclone V series FPGA device from Intel Altera, featuring the 5CSEMA5F31C6N chip, is used. To provide a complete hardware solution, the proposed DOST core has been integrated into a hybrid ARM-HPS (Advanced RISC Machine–Hard Processor System) control unit, which allows the control of different peripherals, such as communication protocols and VGA-based displays. Results show that less than 5% of the chip’s resources are occupied, indicating a low-cost architecture that can be easily integrated into other FPGA structures or hardware systems for diverse applications. Moreover, the accuracy of the proposed FPGA-based implementation is underscored by a root mean squared error of 6.0155 × 10−3 when compared with results from floating-point processors, highlighting its accuracy.

A Geometric Phase Presetting Technique for CP Agile and Beam-Steering Reconfigurable Array With Enhanced AR Bandwidth

A Geometric Phase Presetting Technique for CP Agile and Beam-Steering Reconfigurable Array With Enhanced AR Bandwidth

SAT-Based Exact Modulo Scheduling Mapping for Resource-Constrained CGRAs

Coarse-Grain Reconfigurable Arrays (CGRAs) represent emerging low-power architectures designed to accelerate Compute-Intensive Loops (CILs). The effectiveness of CGRAs in providing acceleration relies on the quality of mapping: how efficiently the CIL is compiled onto the platform. State-of-the-Art (SoA) compilation techniques utilize modulo scheduling to minimize the Iteration Interval (II) and use graph algorithms like Max-Clique Enumeration to address mapping challenges. Our work approaches the mapping problem through a satisfiability (SAT) formulation. We introduce the Kernel Mobility Schedule (KMS), an ad hoc schedule used with the Data Flow Graph and CGRA architectural information to generate Boolean statements that, when satisfied, yield a valid mapping. Experimental results demonstrate SAT-MapIt outperforming SoA alternatives in almost 50% of explored benchmarks. Additionally, we evaluated the mapping results in a synthesizable CGRA design and emphasized the runtime metrics trends, i.e., energy efficiency and latency, across different CILs and CGRA sizes. We show that a hardware-agnostic analysis performed on compiler-level metrics can optimally prune the architectural design space, while still retaining Pareto-optimal configurations. Moreover, by exploring how implementation details impact cost and performance on real hardware, we highlight the importance of holistic software-to-hardware mapping flows, as the one presented herein.

Anti-distortion bioinspired camera with an inhomogeneous photo-pixel array

The bioinspired camera, comprising a single lens and a curved image sensor—a photodiode array on a curved surface—, was born of flexible electronics. Its economical build lends itself well to space-constrained machine vision applications. The curved sensor, much akin to the retina, helps image focusing, but the curvature also creates a problem of image distortion, which can undermine machine vision tasks such as object recognition. Here we report an anti-distortion single-lens camera, where 4096 silicon photodiodes arrayed on a curved surface in a nonuniform pattern assimilated to the distorting optics are the key to anti-distortion engineering. That is, the photo-pixel distribution pattern itself is warped in the same manner as images are warped, which correctively reverses distortion. Acquired images feature no appreciable distortion across a 120° horizontal view, as confirmed by their neural-network recognition accuracies. This distortion correction via photo-pixel array reconfiguration is a form of in-sensor computing.

Backpropagation artificial neural network-based maximum power point tracking controller with image encryption inspired solar photovoltaic array reconfiguration

The enhancement of photovoltaic (PV) arrays through reconfiguration presents a promising avenue for increasing the global maximum power (GMP) and improving overall array performance. This enhancement is achieved by minimizing differences between rows, thereby reducing the computational load on Maximum Power Point Tracking (MPPT) systems. However, many existing reconfiguration methods face various challenges, including scalability issues, inadequate shading dispersion, distortion of array characteristics, emergence of multiple power peaks, increased mismatch, and more. In order to overcome these obstacles, this study presents a novel method for array reconfiguration that is modelled after the widely used Kolakoski Sequence Transform in picture encryption. The suggested approach is assessed in eight different scenarios with 9 × 9 and 5 × 5 PV arrays shaded differently. Its performance is compared against seven established techniques. Due to its intelligent reconfiguration aimed at minimizing shade dispersion, the suggested approach consistently outperforms alternative methods. It results in substantial improvements in GMP, enhancing it by 32.79%, 14.98%, 10.15%, and 4.13% for 9 × 9 arrays, and 37.10%, 14.36%, and 9.88% for 5 × 5 arrays across diverse conditions. Furthermore, this study comprehensively investigates three separate Artificial Neural Network algorithms, specifically the Levenberg-Marquardt (LMB), Scaled Conjugate Gradient, and Bayesian Regularization algorithms for MPPT. A Levenberg-Marquardt Backpropagation-based MPPT controller for a 250Wp standalone PV system is used to validate the effectiveness of the recommended configuration. This integrated approach, which combines reconfiguration and LMB-based MPPT utilizes only two sensors regardless of array size. It achieves accelerated convergence tracking within a short 0.13 s, displaying minimal steady-state oscillations.

High-stiffness reconfigurable surfaces based on bistable element assembly and bi-compatible truss attachment

Reconfigurable surfaces contribute to multi-task robotic platforms, such as reconfigurable phased array antennas with variable aperture, by morphing between multiple specified shapes. Controlling each tile to approximate the variating shape of target surfaces requires a large number of accurate actuators. Previous research has demonstrated employing bistable-element-assembly to form reconfigurable surfaces for significant actuation simplification but suffering from low out-of-plane stiffness resulting in the lack of load-bearing capacity for carrying functional units with good mechanical accuracy. This paper proposes a design framework for tile-assembling bistable (TAB) surfaces with bi-compatible truss attachment for two prescribable stable configurations. The bistability comes from joining surface tiles with bistable elements, which contributes to easy actuation with fewer inaccurate actuators. Bi-compatible truss structures, which are only kinematically compatible at the two prescribed states, are introduced to enhance the out-of-plane stiffness of the TAB surface and improve its load-bearing capacity. Additionally and consequently, the kinematic determinacy of the reconfigurable surfaces is increased by the truss introduction, where bistable elements control the metric while truss structures dictate the principal curvature of the surface. This diminishes the redundant degrees of freedom with enhanced shape-approximation and reconfiguration-coordination. Four prototypes are designed and manufactured, which are a three-tile by three-tile (3 × 3) TAB surface that is stable at flat and spherical configurations, a 5 × 5 TAB surface with flat and spherical stable configurations, a 3 × 3 TAB surface that is stable at the flat and saddle configurations, and a 3 × 3 TAB surface that is stable at the sphere and saddle shapes. The out-of-plane stiffness, easiness of actuation, and shape accuracy of all prototypes are evaluated and show promises for real engineering applications.

High-accuracy beam generation and scanning using reconfigurable coding metasurface

Metasurface technology has attracted widespread attention, owing to its remarkable capability to control electromagnetic properties. In this paper, we design a reconfigurable reflective metasurface array operating at 5 GHz for beam generation and scanning based on coding metasurface. Field programmable gate array (FPGA) is equipped for switching the states of PIN (positive-intrinsic-negative) diodes loaded on the metasurface in real-time, resulting in a 180° phase difference. To obtain multi-beam radiation and high-accuracy beam steering, the coding sequence to produce the target radiation pattern is calculated by an algorithm program. We design the fitness function of a genetic algorithm (GA) to optimize the sequence corresponding to the target directions. The simulation result shows that with the accuracy of 1°, the proposed metasurface is capable of generating multi-beam and scanning two-dimensional beams within the 50° range. Further, we fabricate and measure a prototype sample of 15 × 15 elements, which is verified feasible by comparing the measured result and the simulation. This work demonstrates the great potential of applying this reflective metasurface to wireless communication or radar.