Protein Film Voltammetry Research Articles

Unraveling the Mechanism of Catalytic Reduction of O2 by Microperoxidase-11 Adsorbed within a Transparent 3D-Nanoporous ITO Film

Nanoporous films of indium tin oxide (ITO), with thicknesses ranging from 250 nm to 2 μm, were prepared by Glancing Angle Deposition (GLAD) and used as highly sensitive transparent 3D-electrodes for quantitatively interrogating, by time-resolved spectroelectrochemistry, the reactivity of microperoxidase-11 (MP-11) adsorbed within such films. The capacitive current densities of these 3D-electrodes as well as the amount of adsorbed MP-11 were shown to be linearly correlated to the GLAD ITO film thickness, indicating a homogeneous distribution of MP-11 across the film as well as homogeneous film porosity. Under saturating adsorption conditions, MP-11 film concentration as high as 60 mM was reached. This is equivalent to a stack of 110 monolayers of MP-11 per micrometer film thickness. This high MP-11 film loading combined with the excellent ITO film conductivity has allowed the simultaneous characterization of the heterogeneous one-electron transfer dynamics of the MP-11 Fe(III)/Fe(II) redox couple by cyclic voltammetry and cyclic voltabsorptometry, up to a scan rate of few volts per second with a satisfactory single-scan signal-to-noise ratio. The potency of the method to unravel complex redox coupled chemical reactions was also demonstrated with the catalytic reduction of oxygen by MP-11. In the presence of O(2), cross-correlation of electrochemical and spectroscopic data has allowed us to determine the key kinetics and thermodynamics parameters of the redox catalysis that otherwise could not be easily extracted using conventional protein film voltammetry. On the basis of numerical simulations of cyclic voltammograms and voltabsorptograms and within the framework of different plausible catalytic reaction schemes including appropriate approximations, it was shown possible to discriminate between different possible catalytic pathways and to identify the relevant catalytic cycle. In addition, from the best fits of simulations to the experimental voltammograms and voltabsorptograms, the partition coefficient of O(2) for the ITO film as well as the values of two kinetic rate constants could be extracted. It was finally concluded that the catalytic reduction of O(2) by MP-11 adsorbed within nanoporous ITO films occurs via a 2-electron mechanism with the formation of an intermediate Fe(III)-OOH adduct characterized by a decay rate of 11 s(-1). The spectroelectroanalytical strategy presented here opens new opportunities for characterizing complex redox-coupled chemical reactions not only with redox proteins, but also with redox biomimetic systems and catalysts. It might also be of great interest for the development and optimization of new spectroelectrochemical sensors and biosensors, or eventually new photoelectrocatalytic systems or biofuel cells.

Menaquinone-7 Is Specific Cofactor in Tetraheme Quinol Dehydrogenase CymA

Little is known about enzymatic quinone-quinol interconversions in the lipid membrane when compared with our knowledge of substrate transformations by globular enzymes. Here, the smallest example of a quinol dehydrogenase in nature, CymA, has been studied. CymA is a monotopic membrane tetraheme c-type cytochrome belonging to the NapC/NirT family and central to anaerobic respiration in Shewanella sp. Using protein-film electrochemistry, it is shown that vesicle-bound menaquinone-7 is not only a substrate for this enzyme but is also required as a cofactor when converting other quinones. Here, we propose that the high concentration of quinones in the membrane negates the evolutionary pressure to create a high affinity active site. However, the instability and reactivity of reaction intermediate, semiquinone, might require a cofactor that functions to minimize damaging side reactions.

Voltammetric study of the adsorbed thermophilic plastocyanin from Phormidium laminosum up to 90 °C

Redox thermodynamics and kinetics of plastocyanin from Phormidium laminosum, and of azurin from Pseudonomas aeruginosa, have been investigated as a function of temperature by protein film voltammetry. To this purpose, both proteins have been physisorbed on a pyrolytic graphite edge electrode. A pronounced negative shift of the plastocyanin standard potential, compared to a slight shift in the case of azurin, has been found upon increasing the temperature. Hence, significant conformational and/or solvation changes accompany the redox conversion of plastocyanin. Lower electron transfer rate constants (by c.a. one order of magnitude) and higher activation enthalpies have been found for plastocyanin as compared to azurin. The voltammetric response of azurin vanishes irreversibly at temperatures close to 60°C, whereas the redox properties of plastocyanin remain unaltered, except for some loss of electroactive protein, after heating the electrode at temperatures as high as 90°C.

Theoretical aspects of several successive two-step redox mechanisms in protein-film cyclic staircase voltammetry

Protein-film voltammetry (PFV) is a versatile tool designed to provide insight into the enzymes physiological functions by studying the redox properties of various oxido-reductases with suitable voltammetric technique. The determination of the thermodynamic and kinetic parameters relevant to protein's physiological properties is achieved via methodologies established from theoretical considerations of various mechanisms in PFV. So far, the majority of the mathematical models in PFV have been developed for redox proteins undergoing a single-step electron transfer reactions. However, there are many oxido-reductases containing quinone moieties or polyvalent ions of transition metals like Mo, Mn, W, Fe or Co as redox centers, whose redox chemistry can be described only via mathematical models considering successive two-step electron transformation. In this work we consider theoretically the protein-film redox mechanisms of the EE (Electrochemical–Electrochemical), ECE (Electrochemical–Chemical–Electrochemical), and EECat (Electrochemical–Electrochemical–Catalytic) systems under conditions of cyclic staircase voltammetry. We also propose methodologies to determine the kinetics of electron transfer steps by all considered mechanisms. The experimentalists working with PFV can get large benefits from the simulated voltammograms given in this work.

Laue crystal structure of Shewanella oneidensis cytochrome c nitrite reductase from a high-yield expression system.

The high-yield expression and purification of Shewanella oneidensis cytochrome c nitrite reductase (ccNiR) and its characterization by a variety of methods, notably Laue crystallography, are reported. A key component of the expression system is an artificial ccNiR gene in which the N-terminal signal peptide from the highly expressed S. oneidensis protein "small tetraheme c" replaces the wild-type signal peptide. This gene, inserted into the plasmid pHSG298 and expressed in S. oneidensis TSP-1 strain, generated approximately 20 mg crude ccNiR per liter of culture, compared with 0.5-1 mg/L for untransformed cells. Purified ccNiR has nitrite and hydroxylamine reductase activities comparable to those previously reported for Escherichia coli ccNiR, and is stable for over 2 weeks in pH 7 solution at 4 °C. UV/vis spectropotentiometric titrations and protein film voltammetry identified five independent one-electron reduction processes. Global analysis of the spectropotentiometric data also allowed determination of the extinction coefficient spectra for the five reduced ccNiR species. The characteristics of the individual extinction coefficient spectra suggest that, within each reduced species, the electrons are distributed among the various hemes, rather than being localized on specific heme centers. The purified ccNiR yielded good-quality crystals, with which the 2.59-Å-resolution structure was solved at room temperature using the Laue diffraction method. The structure is similar to that of E. coli ccNiR, except in the region where the enzyme interacts with its physiological electron donor (CymA in the case of S. oneidensis ccNiR, NrfB in the case of the E. coli protein).

Developing the mechanism of dioxygen reduction catalyzed by multicopper oxidases using protein film electrochemistry

We present electrochemical and computational evidence of additional features in the mechanism for the reduction of O2 catalyzed by enzymes known as the multicopper oxidases (MCOs). Using protein film electrochemistry, we show that the dormant “Resting Oxidized” state of the enzyme must be in equilibrium with a catalytically active form. In four different MCOs turning over O2 at pH values several units above their respective optima, we observed electrocatalytic behavior consistent with a second reversible resting state that lies outside the main catalytic cycle (the “X State”). We describe how electrochemistry alone can be used to determine all the rate constants incorporated in our expanded mechanism for MCO-catalyzed O2 reduction, using fully catalytically competent enzyme. We compare high-potential MCOs (laccases from Trametes versicolor and Coriolopsis gallica, and bilirubin oxidase from Myrothecium verrucaria) and low-potential MCOs (laccase from Rhus vernicifera and CotA from Bacillus subtilis), and explain how the same scheme and analysis can be used in both cases, even though specific rate constants vary widely between species. For example, the rate of formation of the Resting Oxidized state is ∼1000 times faster in high-potential MCOs than in low-potential analogues. In contrast, all the MCOs showed similar X State fractions. For laccase from Trametes versicolor, about a quarter of the enzyme molecules occupy the X State during catalysis at high pH values. These findings are elucidated through computational finite time difference modeling and numerical analysis, which allows the X State to be positioned in the catalytic cycle as a dead-end state from the Peroxy Intermediate.

Characterization of Binding and Electron Transfer Between Shewanella Cytochrome C Peroxidase and its Monoheme Electron Donor C5

Bacterial diheme cytochrome c peroxidases are a critical part of the detoxification pathways in the periplasmic space that convert hydrogen peroxide to water. The turnover of peroxide requires a two-electron reduction, and these reducing equivalents must be delivered to the peroxidase by soluble electron transfer proteins. This study focuses on the diheme cytochrome c peroxidase from Shewanella oneidensis (So CcP). We have shown previously that a monoheme electron transfer protein from Shewanella oneidensis, So c5, is capable of both activating and turning over the So CcP protein during in vitro peroxidase assays. The nature of the protein-protein interface is not known, especially since two different molecules of So c5 must bind So CcP, either sequentially or simultaneously, during the catalytic cycle. We postulate that for efficient in vivo activity, oxidized So CcP should preferentially bind to the reduced So c5, and the interaction should weaken substantially once the electron has been transferred. In our current work, we show that charge-reversal amino acid mutations on the putative protein-protein interface failed to substantially change the Km for So c5 in peroxidase activity assays. However, surface charge-reversal mutations did have subtle effects consistent with changes in the electron transfer pathways as measured by protein film voltammetry. We further investigated the interaction between So c5 and So CcP using a surface acoustic wave binding method. Binding between So CcP and So c5 is very weak, with observed dissociation constants around 20 μM, and the interaction can be modulated by surface charge-reversal mutations. However, the rate of dissociation of oxidized So CcP from oxidized So c5 is surprisingly slow, suggesting our current models of the in vivo catalytic cycle of So CcP may need to be revisited.

Spectroscopic analysis of immobilised redox enzymes under direct electrochemical control

This article reviews recent developments in spectroscopic analysis of electrode-immobilised enzymes under direct, unmediated electrochemical control. These methods unite the suite of spectroscopic methods available for characterisation of structural, electronic and coordination changes in proteins with the exquisite control over complex redox enzymes that can be achieved in protein film electrochemistry in which immobilised protein molecules exchange electrons directly with an electrode. This combination is particularly powerful in studies of highly active enzymes where redox states can be controlled even under fast electrocatalytic turnover. We examine examples in which UV-visible, IR, Raman and MCD spectroscopy have been combined with direct electrochemistry to probe redox-dependent chemistry, and consider future opportunities for 'direct' spectroelectrochemistry of immobilised enzymes.

Catalytic Properties of the Isolated Diaphorase Fragment of the NAD+-Reducing [NiFe]-Hydrogenase from Ralstonia eutropha

The NAD+-reducing soluble hydrogenase (SH) from Ralstonia eutropha H16 catalyzes the H2-driven reduction of NAD+, as well as reverse electron transfer from NADH to H+, in the presence of O2. It comprises six subunits, HoxHYFUI2, and incorporates a [NiFe] H+/H2 cycling catalytic centre, two non-covalently bound flavin mononucleotide (FMN) groups and an iron-sulfur cluster relay for electron transfer. This study provides the first characterization of the diaphorase sub-complex made up of HoxF and HoxU. Sequence comparisons with the closely related peripheral subunits of Complex I in combination with UV/Vis spectroscopy and the quantification of the metal and FMN content revealed that HoxFU accommodates a [2Fe2S] cluster, FMN and a series of [4Fe4S] clusters. Protein film electrochemistry (PFE) experiments show clear electrocatalytic activity for both NAD+ reduction and NADH oxidation with minimal overpotential relative to the potential of the NAD+/NADH couple. Michaelis-Menten constants of 56 µM and 197 µM were determined for NADH and NAD+, respectively. Catalysis in both directions is product inhibited with K I values of around 0.2 mM. In PFE experiments, the electrocatalytic current was unaffected by O2, however in aerobic solution assays, a moderate superoxide production rate of 54 nmol per mg of protein was observed, meaning that the formation of reactive oxygen species (ROS) observed for the native SH can be attributed mainly to HoxFU. The results are discussed in terms of their implications for aerobic functioning of the SH and possible control mechanism for the direction of catalysis.

Oxygen-Tolerant [NiFe]-Hydrogenases: The Individual and Collective Importance of Supernumerary Cysteines at the Proximal Fe-S Cluster

An important clue to the mechanism for O(2) tolerance of certain [NiFe]-hydrogenases is the conserved presence of a modified environment around the iron-sulfur cluster that is proximal to the active site. The O(2)-tolerant enzymes contain two cysteines, located at opposite ends of this cluster, which are glycines in their O(2)-sensitive counterparts. The strong correlation highlights special importance for electron-transfer activity in the protection mechanism used to combat O(2). Site-directed mutagenesis has been carried out on Escherichia coli hydrogenase-1 to substitute these cysteines (C19 and C120) individually and collectively for glycines, and the effects of each replacement have been determined using protein film electrochemistry and electron paramagnetic resonance (EPR) spectroscopy. The "split" iron-sulfur cluster EPR signal thus far observed when oxygen-tolerant [NiFe]-hydrogenases are subjected to oxidizing potentials is found not to provide any simple, reliable correlation with oxygen tolerance. Oxygen tolerance is largely conferred by a single cysteine (C19), replacement of which by glycine removes the ability to function even in 1% O(2).

The [NiFe]-Hydrogenase of the Cyanobacterium Synechocystis sp. PCC 6803 Works Bidirectionally with a Bias to H2 Production

Protein film electrochemistry (PFE) was utilized to characterize the catalytic activity and oxidative inactivation of a bidirectional [NiFe]-hydrogenase (HoxEFUYH) from the cyanobacterium Synechocystis sp. PCC 6803. PFE provides precise control of the redox potential of the adsorbed enzyme so that its activity can be monitored under changing experimental conditions as current. The properties of HoxEFUYH are different from those of both the standard uptake and the "oxygen-tolerant" [NiFe]-hydrogenases. First, HoxEFUYH is biased toward proton reduction as opposed to hydrogen oxidation. Second, despite being expressed under aerobic conditions in vivo, HoxEFUYH is clearly not oxygen-tolerant. Aerobic inactivation of catalytic hydrogen oxidation by HoxEFUYH is total and nearly instantaneous, producing two inactive states. However, unlike the Ni-A and Ni-B inactive states of standard [NiFe]-hydrogenases, both of these states are quickly (<90 s) reactivated by removal of oxygen and exposure to reducing conditions. Third, proton reduction continues at 25-50% of the maximal rate in the presence of 1% oxygen. Whereas most previously characterized [NiFe]-hydrogenases seem to be preferential hydrogen oxidizing catalysts, the cyanobacterial enzyme works effectively in both directions. This unusual catalytic bias as well as the ability to be quickly reactivated may be essential to fulfilling the physiological role in cyanobacteria, organisms expected to experience swings in cellular reduction potential as they switch between aerobic conditions in the light and dark anaerobic conditions. Our results suggest that the uptake [NiFe]-hydrogenases alone are not representative of the catalytic diversity of [NiFe]-hydrogenases, and the bidirectional heteromultimeric enzymes may serve as valuable models to understand the diverse mechanisms of tuning the reactivity of the hydrogen activating site.

Geobacter sulfurreducens Cytochrome c Peroxidases: Electrochemical Classification of Catalytic Mechanisms

Bacterial cytochrome c peroxidase (CcP) enzymes are diheme redox proteins that reduce hydrogen peroxide to water. They are canonically characterized by a peroxidatic (called L, for "low reduction potential") active site heme and a secondary heme (H, for "high reduction potential") associated with electron transfer, and an enzymatic activity that exists only when the H-heme is prereduced to the Fe(II) oxidation state. The prereduction step results in a conformational change at the active site itself, where a histidine-bearing loop will adopt an "open" conformation allowing hydrogen peroxide to bind to the Fe(III) of the L-heme. Notably, the enzyme from Nitrosomonas europaea does not require prereduction. Previously, we have shown that protein film voltammetry (PFV) is a highly useful tool for distinguishing the electrocatalytic mechanisms of the Nitromonas type of enzyme from other CcPs. Here, we apply PFV to the recently described enzyme from Geobacter sulfurreducens and the Geobacter S134P/V135K double mutant, which have been shown to be similar to members of the canonical subclass of peroxidases and the Nitrosomonas subclass of enzymes, respectively. Here we find that the wild-type Geobacter CcP is indeed similar electrochemically to the bacterial CcPs that require reductive activation, yet the S134P/V135K mutant shows two phases of electrocatalysis: one that is low in potential, like that of the wild-type enzyme, and a second, higher-potential phase that has a potential dependent upon substrate binding and pH yet is at a potential that is very similar to that of the H-heme. These findings are interpreted in terms of a model in which rate-limiting intraprotein electron transfer governs the catalytic performance of the S134P/V135K enzyme.

Analysis of the activation mechanism of Pseudomonas stutzeri cytochrome c peroxidase through an electron transfer chain

The activation mechanism of Pseudomonas stutzeri cytochrome c peroxidase (CCP) was probed through the mediated electrochemical catalysis by its physiological electron donor, P. stutzeri cytochrome c-551. A comparative study was carried out, by performing assays with the enzyme in the resting oxidized state as well as in the mixed-valence activated form, using cyclic voltammetry and a pyrolytic graphite membrane electrode. In the presence of both the enzyme and hydrogen peroxide, the peak-like signal of cytochrome c-551 is converted into a sigmoidal wave form characteristic of an E(r)C'(i) catalytic mechanism. An intermolecular electron transfer rate constant of (4 ± 1) × 10(5) M(-1) s(-1) was estimated for both forms of the enzyme, as well as a similar Michaelis-Menten constant. These results show that neither the intermolecular electron transfer nor the catalytic activity is kinetically controlled by the activation mechanism of CCP in the case of the P. stutzeri enzyme. Direct enzyme catalysis using protein film voltammetry was unsuccessful for the analysis of the activation mechanism, since P. stutzeri CCP undergoes an undesirable interaction with the pyrolytic graphite surface. This interaction, previously reported for the Paracoccus pantotrophus CCP, induces the formation of a non-native conformation state of the electron-transferring haem, which has a redox potential 200 mV lower than that of the native state and maintains peroxidatic activity.

Protein film voltammetry: electrochemical enzymatic spectroscopy. A review on recent progress

This review is focused on the basic principles, the main applications, and the theoretical models developed for various redox mechanisms in protein film voltammetry, with a special emphasis to square-wave voltammetry as a working technique. Special attention is paid to the thermodynamic and kinetic parameters of relevant enzymes studied in the last decade at various modified electrodes, and their use as a platform for the detection of reactive oxygen species is also discussed. A set of recurrent formulas for simulations of different redox mechanisms of lipophilic enzymes is supplied together with representative simulated voltammograms that illustrate the most relevant voltammetric features of proteins studied under conditions of square-wave voltammetry.

Catalytic mechanism in successive two-step protein-film voltammetry—Theoretical study in square-wave voltammetry

Protein-film voltammetry is established as an effective tool that provides insight to the redox features of various lipophilic proteins by using a simple methodology. Although the protein-film experimental set up is relatively simple, the redox mechanisms of many proteins are quite complicated, and very often they cannot be resolved without having support from adequate mathematical models. In this work we continue our contribution to modeling relevant redox mechanisms in protein-film voltammetry. We present results from the theoretical simulations of catalytic mechanism at the two-step successive surface redox reaction under conditions of square-wave voltammetry. This mechanism is assigned as a surface EEC′, and it can be presented by the following simplified scheme: A(ads) + ne− ⇄ B(ads) + ne− ⇄ C(ads) + Substrate → k cat B(ads). Our attention is focused on several phenomena of this complex protein-film mechanism, while we give set of qualitative criteria to distinguish this mechanism from similar ones studied under voltammetric conditions. Moreover, we also provide hints to use methodologies for the determination of thermodynamic and kinetic parameters relevant to the protein-film EEC′ mechanism. The considered protein-film EEC′ mechanism is applicable to all lipophilic redox proteins that undergo electrochemical transformations in more than one successive electron steps. Such examples exist by proteins containing quinone moiety and some polyvalent ions of transition metals as redox active sites.

Direct electrochemistry of cytochrome c entrapped in agarose hydrogel by protein film voltammetry

Cytochrome c (cyt-c) entrapped in agarose hydrogel was electrostatically bound to the edge plane pyrolytic graphite electrode (EPPGE), and then stable agarose-cyt-c/EPPGE was prepared. Direct electrochemistry between cyt-c and the EPPGE was monitored by protein film voltammetry. The effects of ionic strength, pH and exterior substances on the direct electrochemistry, and electrocatalytic properties of cyt-c were also studied. Results show that the electrochemical behavior of heme Fe(III)/Fe(II) in cyt-c is quasireversible. Its electrochemical performance is the best when the concentration of supporting electrolyte phosphate buffer solution is 0.2 mol/l and pH is 7.0, and greatly inhibited by exterior metal ions. Catalytic reduction of oxygen could also be achieved at the agarose-cyt-c/EPPGE.

CO Disrupts the Reduced H-Cluster of FeFe Hydrogenase. A Combined DFT and Protein Film Voltammetry Study

Carbon monoxide is often described as a competitive inhibitor of FeFe hydrogenases, and it is used for probing H(2) binding to synthetic or in silico models of the active site H-cluster. Yet it does not always behave as a simple inhibitor. Using an original approach which combines accurate electrochemical measurements and theoretical calculations, we elucidate the mechanism by which, under certain conditions, CO binding can cause permanent damage to the H-cluster. Like in the case of oxygen inhibition, the reaction with CO engages the entire H-cluster, rather than only the Fe(2) subsite.

Electrocatalytic reduction of nitrate and selenate by NapAB

Bacterial cellular metabolism is renowned for its metabolic diversity and adaptability. However, certain environments present particular challenges. Aerobic metabolism of highly reduced carbon substrates by soil bacteria such as Paracoccus pantotrophus presents one such challenge since it may result in excessive electron delivery to the respiratory redox chain when compared with the availability of terminal oxidant, O2. The level of a periplasmic ubiquinol-dependent nitrate reductase, NAP, is up-regulated in the presence of highly reduced carbon substrates. NAP oxidizes ubiquinol at the periplasmic face of the cytoplasmic membrane and reduces nitrate in the periplasm. Thus its activity counteracts the accumulation of excess reducing equivalents in ubiquinol, thereby maintaining the redox poise of the ubiquinone/ubiquinol pool without contributing to the protonmotive force across the cytoplasmic membrane. Although P. pantotrophus NapAB shows a high level of substrate specificity towards nitrate, the enzyme has also been reported to reduce selenate in spectrophotometric solution assays. This transaction draws on our current knowledge concerning the bacterial respiratory nitrate reductases and extends the application of PFE (protein film electrochemistry) to resolve and quantify the selenate reductase activity of NapAB.

Formaldehyde—A Rapid and Reversible Inhibitor of Hydrogen Production by [FeFe]-Hydrogenases

Dihydrogen (H(2)) production by [FeFe]-hydrogenases is strongly inhibited by formaldehyde (methanal) in a reaction that is rapid, reversible, and specific to this type of hydrogenase. This discovery, using three [FeFe]-hydrogenases that are homologous about the active site but otherwise structurally distinct, was made by protein film electrochemistry, which measures the activity (as electrical current) of enzymes immobilized on an electrode; importantly, the inhibitor can be removed after addition. Formaldehyde causes rapid loss of proton reduction activity which is restored when the solution is exchanged. Inhibition is confirmed by conventional solution assays. The effect depends strongly on the direction of catalysis: inhibition of H(2) oxidation is much weaker than for H(2) production, and formaldehyde also protects against CO and O(2) inactivation. By contrast, inhibition of [NiFe]-hydrogenases is weak. The results strongly suggest that formaldehyde binds at, or close to, the active site of [FeFe]-hydrogenases at a site unique to this class of enzyme--highly conserved lysine and cysteine residues, the bridgehead atom of the dithiolate ligand, or the reduced Fe(d) that is the focal center of catalysis.

The relationship between redox enzyme activity and electrochemical potential—cellular and mechanistic implications from protein film electrochemistry

In protein film electrochemistry a redox protein of interest is studied as an electroactive film adsorbed on an electrode surface. For redox enzymes this configuration allows quantification of the relationship between catalytic activity and electrochemical potential. Considered as a function of enzyme environment, i.e., pH, substrate concentration etc., the activity-potential relationship provides a fingerprint of activity unique to a given enzyme. Here we consider the nature of the activity-potential relationship in terms of both its cellular impact and its origin in the structure and catalytic mechanism of the enzyme. We propose that the activity-potential relationship of a redox enzyme is tuned to facilitate cellular function and highlight opportunities to test this hypothesis through computational, structural, biochemical and cellular studies.