Polymethylpentene Research Articles

Characterization of anisotropic pore structure and dense selective layer of capillary membranes for long-term ECMO by cross-sectional ion-milling method.

Since the COVID-19 pandemic of 2020-2023, extracorporeal membrane oxygenator (ECMO) has attracted considerable attention worldwide. It is expected that ECMO with long-term durability is put into practical use in order to prepare for next emerging infectious diseases and to facilitate manufacturing for novel medical devices. Polypropylene (PP) and polymethylpentene (PMP) capillary membranes are currently the mainstream for gas exchange membrane for ECMO. ECMO support days for COVID-19-related acute hypoxemic respiratory failure have been reported to be on average for 14 or 24days. It is necessary to improve opposing functions such that promoting the permeation of oxygen and carbon dioxide and inhibiting the permeation of water vapor or plasma to develop sufficient durability for long-term use. For this purpose, accurately controlling the anisotropy of the pore structure of the entire cross section and functions of capillary membrane is significant. In this study, we focused on the cross-sectional ion-milling (CSIM) method, to precisely clarify the pore structure of the entire cross section of capillary membrane for ECMO, because there is less physical stress on the porous structure applied during the preparation of cross-sectional samples of porous capillary membranes. We attempted to observe the cross sections of commercially available PMP membranes using the CSIM method. As a result, we succeeded in fabricating fine-scale flat cross-sectional samples of PMP capillary membranes. The pore structures and the degree of anisotropy of the cross sections are quantitatively clarified. The achievements and the approaches of this study are being applied to the development of next-generation gas exchange membranes.

Comparative analysis of oxygenator dysfunction in polymethylpentene oxygenators: A pilot study.

Polymethylpentene (PMP) oxygenators serve as the primary oxygenator type utilized for ECMO. With the number of PMP oxygenators available, it has become increasingly important to determine differences among each oxygenator type that can lead to varying metrics of oxygenator dysfunction. This study was a retrospective, single-center analysis of adult patients supported on ECMO between December 2020 to December 2021 with varying PMP oxygenators including the Medtronic Nautilus Smart (Minneapolis, MA), the Eurosets AMG PMP (Medolla, Italy) and Getinge Quadrox-iD and the Getinge Cardiohelp HLS Module Advanced System (Gothenberg, Sweden). A total of 19 patients were included in our study. 10 patients (52.6%) were supported with a Medtronic Nautilus Smart oxygenator, 5 patients (26.3%) were supported with an Eurosets AMG PMP Oxygenator, and 4 patients (21.1%) were supported with either a Getinge Quadrox-iD oxygenator or Getinge Cardiohelp HLS system. Patients supported with Eurosets AMG PMP oxygenators experienced higher resistance and lower post-oxygenator PaO2 in comparison to other cohorts (p < .02 and < .002 respectively). There was no difference in measured oxygen transfer between cohorts (p = .667). Two patients, both supported by Eurosets AMG PMP, experienced oxygenator failure (p = .094). Radial flow oxygenators are prone to higher resistance and lower post-oxygenator PaO2when compared to transverse flow oxygenators. Future larger multicenter studies are required to fully discern the differences between flow-varying polymethylpentene oxygenators and their appropriate cutoffs for oxygenator dysfunction.

Stability Enhancement by Hydrophobic Anchoring and a Cross-Linked Structure of a Phospholipid Copolymer Film for Medical Devices.

Surface modification using zwitterionic 2-methacryloyloxyethylphosphorylcholine (MPC) polymers is one of the most reasonable ways to prepare medical devices that can suppress undesired biological reactions such as blood coagulation. Usable MPC polymers are hydrophilic and water soluble, and their surface modification strategy involves exploiting the copolymer structures by adding physical or chemical bonding moieties. In this study, we developed copolymers composed of MPC, hydrophobic anchoring moiety, and chemical cross-linking unit to clarify the role of hydrophobic interactions in achieving biocompatible and long-term stable coatings. The four kinds of MPC copolymers with cross-linking units, such as 3-methacryloxypropyl trimethoxysilane (MPTMSi), and four different hydrophobic anchoring moieties, such as 3-(methacryloyloxy)propyltris(trimethylsiloxy)silane (MPTSSi) named as PMMMSi, n-butyl methacrylate (BMA) as PMBSi, 2-ethylhexyl methacrylate (EHMA) as PMESi, and lauryl methacrylate as PMLSi, were synthesized and coated on polydimethylsiloxane, polypropylene (PP), and polymethyl pentene. These copolymers were uniformly coated on the substrate materials PP and poly(methyl pentene) (PMP), to achieve hydrophilic and electrically neutral coatings. The results of the antibiofouling test showed that PMBSi repelled the adsorption of fluorescence-labeled bovine serum albumin the most, whereas PMLSi repelled it the least. Notably, all four copolymers suppressed platelet adhesion similarly. The variations in protein adsorption quantities among the four copolymer coatings were attributed to their distinct swelling behaviors in aqueous environments. Further investigations, including 3D scanning force microscopy and neutron reflectivity measurements, revealed that the PMLSi coating exhibited a higher water intake under aqueous conditions in comparison to the other coatings. Consequently, all copolymer coatings effectively prevented the invasion of platelets but the proteins penetrated the PMLSi network. Subsequently, the dynamic stability required to induce shear stress was evaluated using a circulation system. The results demonstrated that the PMMMSi and PMLSi coatings on PMP and PP exhibited exceptional platelet repellency and maintained high stability during circulation. This study highlights the potential of hydrophobic moieties to improve hemocompatibility and stability, offering potential applications in medical devices.

Prototyping in Polymethylpentene to Enable Oxygen-Permeable On-a-Chip Cell Culture and Organ-on-a-Chip Devices Suitable for Microscopy.

With the rapid development and commercial interest in the organ-on-a-chip (OoC) field, there is a need for materials addressing key experimental demands and enabling both prototyping and large-scale production. Here, we utilized the gas-permeable, thermoplastic material polymethylpentene (PMP). Three methods were tested to prototype transparent PMP films suitable for transmission light microscopy: hot-press molding, extrusion, and polishing of a commercial, hazy extruded film. The transparent films (thickness 20, 125, 133, 356, and 653 µm) were assembled as the cell-adhering layer in sealed culture chamber devices, to assess resulting oxygen concentration after 4 days of A549 cell culture (cancerous lung epithelial cells). Oxygen concentrations stabilized between 15.6% and 11.6%, where the thicker the film, the lower the oxygen concentration. Cell adherence, proliferation, and viability were comparable to glass for all PMP films (coated with poly-L-lysine), and transparency was adequate for transmission light microscopy of adherent cells. Hot-press molding was concluded as the preferred film prototyping method, due to excellent and reproducible film transparency, the possibility to easily vary film thickness, and the equipment being commonly available. The molecular orientation in the PMP films was characterized by IR dichroism. As expected, the extruded films showed clear orientation, but a novel result was that hot-press molding may also induce some orientation. It has been reported that orientation affects the permeability, but with the films in this study, we conclude that the orientation is not a critical factor. With the obtained results, we find it likely that OoC models with relevant in vivo oxygen concentrations may be facilitated by PMP. Combined with established large-scale production methods for thermoplastics, we foresee a useful role for PMP within the OoC field.

Effect of Height and Weight on Heel Fat Pad Movements Between Microchamber and Macrochamber Layers in Loading and Unloading

Background: The purpose of this study was to clarify the differences in the movement of the superficial microchambers and deep macrochambers of the heel fat pad during loading and unloading movements, and to clarify the influence of height and weight on this movement. Methods: The subjects were 21 healthy adults. The right foot was placed on an evaluation instrument stand made of polymethylpentene (PMP) resin plate, and the left foot was placed on a scale stand used to adjust the amount of load. When measuring, the heel fat pad is divided into the superficial microchamber layer and the deep macrochamber layer, and the thickness due to loading from 0% to 100% of the body weight and unloading from 100% to 0% is measured. Measurement was performed every 20% using an ultrasound imaging device. We also examined the rate of change in the thickness of the superficial and deep layers of the heel fat pad when applying 100% load (end load) from 0% load (unload). Results: No changes were observed in the superficial layer of the heel fat pad during unloading, but significant changes were observed in the deeper layers. Additionally, the thickness of the microchamber and macrochamber layers tended to increase under each loading condition as the height and weight increased. On the other hand, the rate of change in the thickness of the macrochamber layer tended to decrease. Conclusion: The microchamber layer and the macrochamber layer of the heel fat pad may have different functions. As height and weight increase, the thickness of the microchamber and macrochamber layers may increase, and the rate of change in the thickness of the macrochamber layer appears to decrease. Although the thickness increases as the load increases, we found that the related elasticity decreases. Level of Evidence: Level Ⅳ, cross-sectional survey study.

Efficient sulfide and methane removal in anaerobic secondary effluent using a pilot-scale membrane-aerated biofilm reactor

Anaerobic secondary treatment can enable energy-efficient removal of organic matter but may produce effluent containing dissolved methane and sulfide that must be managed before discharge or reuse. In this study, we operated a Membrane-aerated Biofilm Reactor (MABR) to achieve reliable removal of dissolved sulfide and methane from anaerobic secondary effluent at pilot-scale. The pilot-scale MABR was equipped with gas permeable polymethyl pentene (PMP) membranes, promoting surface growth of aerobic biofilm via diffusion-based aeration (lumen-to-surface diffusion). The system treated anaerobic secondary effluent from a demonstration-scale anaerobic membrane bioreactor (AnMBR) processing 90 m3/d primary effluent. MABR influent flow rate was increased from 8.2 to 32.7 m3/d to elevate substrate loading rates to the biofilm. The MABR consistently achieved >99 % removal of sulfide and dissolved methane, even at the maximum substrate loading rate: 2.3 g-S/m2/d for sulfide and 2.5 g-CH4/m2/d for dissolved methane. Despite effective sulfide and methane removal, incomplete nitrification (<25 % ammonia removal) occurred, with a portion of ammonia converted into nitrous oxide (N2O), a greenhouse gas 298 times more potent than CO2. Operating the MABR incurred low energy costs: 0.01 to 0.05 kWh/m3 for the compressor supplying air to the membrane lumen and 0.01 kWh/m3 for the influent pump. An in-depth mass balance of N2O emissions from the MABR revealed that N2O was subject to counter-diffusion (surface-to-lumen diffusion) in which >99 % of the N2O produced within the biofilm was recovered in off-gas from the gas permeable membranes (hollow fibers).

Outcomes of ECMO support with polypropylene membrane during pandemic times: a retrospective cohort study

BackgroundThe SARS-CoV-2 pandemic resulted in shortages of supplies, which limited the use of extracorporeal membrane oxygenation (ECMO) support. As a contingency strategy, polypropylene (PP) oxygenation membranes were used. This study describes the clinical outcomes in patients on ECMO with PP compared to poly-methylpentene (PMP) oxygenation membranes.MethodsRetrospective cohort of patients in ECMO support admitted between 2020 and 2021.ResultsA total of 152 patients with ECMO support were included, 71.05% were men with an average age of 42 (SD 9.91) years. Veno-venous configuration was performed in 75.6% of cases. The PP oxygenation membranes required more changes 22 (63.1%), than the PMP Sorin® 24 (32,8%) and Euroset® 15 (31,9%) (p.0.022). The main indication for membrane change was low oxygen transfer for PP at 56.2%, Sorin® at 50%, and Euroset® at 14.8%. Renal replacement therapy was the most frequent complication with PP membrane in 22 patients (68.7%) Sorin® 25 patients (34.2%), and Euroset® 15 patients (31.9%) (p 0.001) without statistically significant differences in mortality.ConclusionPP oxygenation membranes was a useful and feasible strategy. It allowed a greater disponibility of ECMO support for critically ill in a situation of great adversity during the SARS-CoV-2 pandemic.

Superhydrophobic polydimethylsiloxane dip-coated polycaprolactone electrospun membrane for extracorporeal membrane oxygenation

Extracorporeal membrane oxygenation (ECMO) is a technique that delivers gas exchange to cardiopulmonary surgery patients. Membrane oxygenation failure may result in serious health problems for patients due to ECMO membrane wetting and surface fouling problems. Thus, in this work, the superhydrophobic membrane is designed to improve the resistance to wetting and long-term fouling of the ECMO membrane. The hydrophobic biocompatible polycaprolactone (PCL) was used to fabricate an electrospun nanofiber membrane. Polydimethylsiloxane (PDMS) was dip-coated on the PCL electrospun membrane to enhance the membrane hydrophobicity, which lifts the water contact angle from 136 to 160°. The PDMS90 membrane shows low protein adsorption under 10 mg/mL BSA incubation, inhibiting the platelet activation and intensifying long-term antifouling of the membrane. The lab-scale blood oxygenation results indicate that the developed membrane is competitive with the commercial polypropylene (PP) and lab-made polymethyl pentene (PMP) membranes. In conclusion, the conducted experiments verify that the developed membrane has the potential to be applied to the ECMO membrane.

Centrifugal or Roller Blood Pumps for Neonatal Venovenous Extracorporeal Membrane Oxygenation: Extracorporeal Life Support Organization Database Comparison of Mortality and Morbidity.

To investigate outcomes associated with conventional roller or centrifugal pumps during neonatal venovenous extracorporeal membrane oxygenation (ECMO). Our primary hypothesis is that in comparison with conventional roller-pump support, centrifugal pump use is associated with greater odds of survival. Our secondary hypothesis is that centrifugal pump use is associated with lesser odds of complications. Retrospective cohort identified using the Extracorporeal Life Support Organization (ELSO) registry 2016 to 2020 dataset. All ECMO centers reporting to the ELSO registry. All neonates (≤ 28 d) supported with venovenous ECMO and cannulated via right internal jugular vein using dual-lumen venovenous cannulas and polymethyl pentene membrane oxygenators. None. A total of 612 neonates (centrifugal, n = 340; conventional roller, n = 272) were included in the analysis. Using a multivariable logistic regression model, centrifugal pump use-as opposed to roller pump use-was associated with lesser odds of survival (odds ratio [OR], 0.53; 95% CI, 0.33-0.84; p < 0.008). Thrombosis and clots in the circuit components were also associated with lesser odds of survival (OR, 0.28; 95% CI, 0.16-0.60; p < 0.001). We failed to show that hemolysis was an independent variable for survival (OR, 0.60; 95% CI, 0.31-1.19; p = 0.14). The primary diagnosis of neonatal aspiration/meconium aspiration is associated with more than seven-fold greater odds of survival (OR, 7.57; 95% CI, 4.02-15.74; p < 0.001). Contrary to our hypotheses, conventional roller pump use was associated with greater odds of survival. While thrombosis and clots in circuit components were independent variables for lesser odds of survival, further research is needed better to understand the use of centrifugal pumps in neonatal practice.

In situ thermal characterisation and filamentary modification in Polymethylpentene

Polymethylpentene (PMP) polymers can be used to make advanced optics, especially for midinfrared (MIR) ultrafast optics. In this study, an optical parametric converter pumped by a Ti sapphire femtosecond laser was used to investigate the polymer. The thermal effect generated by loosely focused femtosecond near mid-infrared (MIR) pulses in bulky materials is observed in real-time, and the polymer exhibits thermal stability and conformability. To avoid strong linear absorption and to increase the nonlinear damage threshold, the spectral region for ultrafast applications is 1310 nm (0.95 eV)–1350 nm (0.92 eV). For the process in region VI, there is a sign of stronger coupling for short-wavelength photons, and the pulse duration is recommended to be lower than 160 fs. In the ultraviolet (UV) region, filamentary writing using a low-focused beam, the laser peak power was selected in the range of 2.2 MW–9.2 MW. High-density bulky gratings were written. The refractive-index modulation was significant, and the polymer exhibited highly nonlinear features. This study provides insights into the applications and production of PMP polymers in laser optics and laser engineering.

Methane-Induced SPR Shifts of Cryptophane A-Doped Polymer Layers

The macromolecular cage cryptophane A can host methane molecules in its cavity and is thus suited as methane-sensing molecules for sensors based on refractive index (RI) sensitive analytical methods such as surface plasmon resonance (SPR). In this work, we assessed the methane response of different cryptophane A-doped polymer membranes by using a custom-made, angular-based SPR device with an RI resolution of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2.4\cdot 10\,\,^{\mathrm{ -5}}$ </tex-math></inline-formula> . We show that cryptophane A needs to be dissolved in doped polymer coatings for successful methane detection. For membranes made of poly(methylmethacrylate) (PMMA), polycarbonate (PC), polystyrene (PS), and polymethylpentene (PMP), cryptophane A could be dissolved, and the solution could not be achieved with polydimethylsiloxane (PDMS) polymers, irrespective of the solvent used. Signal responses and response times toward a methane atmosphere were quantified for different layer thicknesses and cryptophane A contents. The best results were observed for thin but highly doped polymer layers, which could be achieved best for PS layers.

Application of Polymethylpentene, an Oxygen Permeable Thermoplastic, for Long-Term on-a-Chip Cell Culture and Organ-on-a-Chip Devices

The applicability of a gas-permeable, thermoplastic material polymethylpentene (PMP) was investigated, experimentally and analytically, for organ-on-a-chip (OoC) and long-term on-a-chip cell cultivation applications. Using a sealed culture chamber device fitted with oxygen sensors, we tested and compared PMP to commonly used glass and polydimethylsiloxane (PDMS). We show that PMP and PDMS have comparable performance for oxygen supply during 4 days culture of epithelial (A549) cells with oxygen concentration stabilizing at 16%, compared with glass control where it decreases to 3%. For the first time, transmission light images of cells growing on PMP were obtained, demonstrating that the optical properties of PMP are suitable for non-fluorescent, live cell imaging. Following the combined transmission light imaging and calcein-AM staining, cell adherence, proliferation, morphology, and viability of A549 cells were shown to be similar on PMP and glass coated with poly-L-lysine. In contrast to PDMS, we demonstrate that a film of PMP as thin as 0.125 mm is compatible with high-resolution confocal microscopy due to its excellent optical properties and mechanical stiffness. PMP was also found to be fully compatible with device sterilization, cell fixation, cell permeabilization and fluorescent staining. We envision this material to extend the range of possible microfluidic applications beyond the current state-of-the-art, due to its beneficial physical properties and suitability for prototyping by different methods. The integrated device and measurement methodology demonstrated in this work are transferrable to other cell-based studies and life-sciences applications.

Impact of Plastic-Wrap Properties and Cleaning Intervals on the Disinfection of Elevator Buttons.

Fomite transmission is a possible route by which different pathogens spread within facilities. In hospital settings, elevator buttons are widely observed to be covered with various types of plastic wraps; however, limited information is available concerning the impact of different plastic materials on cleaning. Our study aimed to identify which plastic material is suitable for the coverage of elevator buttons and the optimal intervals for their cleaning. We tested six plastic covers, including polyethylene (PE), polymethylpentene (PMP), polyvinyl chloride (PVD), and polyvinylidene chloride (PVDC) plastic wraps; a thermoplastic polyurethane (TPU) keyboard cover; and a polyethylene terephthalate-ethylene vinyl acetate (PET-EVA) laminating film, which are plastic films. The bioburden on the elevator buttons at different time intervals was measured using an adenosine triphosphate (ATP) bioluminescence assay. Our results show that wraps made of PVDC had superior durability compared with those of PMP, PVC, and PVDC, in addition to the lowest detectable ATP levels among the six tested materials. Regarding different button locations, the highest ATP values were found in door-close buttons followed by door-open, and first-floor buttons after one- and three-hour intervals (p = 0.024 and p < 0.001, respectively). After routine disinfection, the ATP levels of buttons rapidly increased after touching and became more prominent after three hours (p < 0.05). Our results indicate that PVDC plastic wraps have adequate durability and the lowest residual bioburden when applied as covers for elevator buttons. Door-close and -open buttons were the most frequently touched sites, requiring more accurate and precise disinfection; therefore, cleaning intervals of no longer than three hours may be warranted.

Factors to control the alignment of surface-treated titanium dioxide powders to maximize performance of sunscreens.

Titanium dioxide powders are contained in a large class of colour cosmetics and sunscreen formulas. When they are used, the formation of a uniform functional powder layer on the skin is an important factor to show their functionality, such as aesthetic and UV protection. Attempts were made to extract the factors that affect the UV shielding ability of the deposited powder layer. Seven kinds of surface treatments were conducted on nano-sized titanium dioxide powder to modify the surface characteristics. Dispersion samples were prepared by mixing these powders with liquids, such as mixed solutions of cyclopentasiloxane, isododecane, coconuts alkane and dimethicone using a disperser and a bead mill. The dispersions were applied using an applicator on cellulose triacetate film, polycarbonate film and polymethyl pentene film. Laser microscope observation and micro-gloss glossmeter analysis were carried out to assess the flatness of the deposited powder layers, and the UV shielding ability was evaluated using SPF analyser. Factors whose influences on the structure and UV shielding ability of the deposited powder layer being analysed were pseudo-HLB of the powders, liquids for preparing the dispersions and material of the substrates. Higher UV shielding ability was attained when powders having pseudo-HLB at around 6 were employed independent from the kinds of liquids and substrates. Flatness of the deposited layer was found to enhance the UV shielding ability of the UV-B region, while that of the UV-A region was scarcely influenced by the flatness. Employing lower surface tension liquids for preparing the dispersions and materials exhibiting lower polar components of surface free energy as substrates tended to enhance the UV shielding ability. Surface treatments conducted on the powders in this study were found to change UV shielding ability, especially UV-B shielding ability, and the relation between pseudo-HLB and UV shielding ability was scarcely influenced by the kinds of liquids. Both surface tension of liquids and the polar component of surface free energy of substrates affected the UV shielding ability. It was suggested that pseudo-HLB calculated based on chemical structure becomes useful information to choose optimum surface treatment to make uniform powder alignment independent from the surrounding environment.

Insights into Gradient and Anisotropic Pore Structures of Capiox® Gas Exchange Membranes for ECMO: Theoretically Verifying SARS-CoV-2 Permeability.

When using the extracorporeal capillary membrane oxygenator (sample A) for ECMO treatments of COVID-19 severely ill patients, which is dominantly used in Japan and worldwide, there is a concern about the risk of SARS-CoV-2 scattering from the gas outlet port of the membrane oxygenator. Terumo has launched two types of membranes (sample A and sample B), both of which are produced by the microphase separation processes using polymethylpentene (PMP) and polypropylene (PP), respectively. However, the pore structures of these membranes and the SARS-CoV-2 permeability through the membrane wall have not been clarified. In this study, we analyzed the pore structures of these gas exchange membranes using our previous approach and verified the SARS-CoV-2 permeation through the membrane wall. Both have the unique gradient and anisotropic pore structure which gradually become denser from the inside to the outside of the membrane wall, and the inner and outer surfaces of the membrane have completely different pore structures. The pore structure of sample A is also completely different from the other membrane made by the melt-extruded stretch process. From this, the pore structure of the ECMO membrane is controlled by designing various membrane-forming processes using the appropriate materials. In sample A, water vapor permeates through the coating layer on the outer surface, but no pores that allow SARS-CoV-2 to penetrate are observed. Therefore, it is unlikely that SARS-CoV-2 permeates through the membrane wall and scatter from sample A, raising the possibility of secondary ECMO infection. These results provide new insights into the evolution of a next-generation ECMO membrane.

A phantom study regarding the formation mechanism of mucosal epithelial echo on intraoral ultrasonography

AbstractObjectivesThis study is aimed to perform imaging of phantoms to simulate intraoral ultrasound and to investigate the formation mechanism of mucosal epithelial echo.MethodsIn this study, we used phantoms, simulated mucosal layer (SML) with thickness of 0.5, 1.0, 3.0 mm and no SML, and an intraoperative small linear probe as ultrasound transducer. Acoustic coupling polymer gel and agar gel were used as the coupling material, and polyvinylidene chloride (PVDC), polyethylene (PE) and polymethylpentene (PMP) plastic wrap were used. The thicknesses of a surface echo and mucosal epithelial echo were measured on B‐mode images.ResultsA surface echo approximately 0.5 mm thick and a hyperechoic line structure approximately 1.0 mm deep in the 3.0‐mm SML, which were presumed to be artifacts, were visualized with all combinations of acoustic coupling material and plastic wrap except with acoustic coupling agar gel and PMP wrap. When using acoustic coupling polymer gel, a hypoechoic line approximately 0.2 mm thick was observed, even when no SML was present. Thickness of the SML appeared to be lesser on ultrasound images than its actual depth, and the most accurate measurement of thickness was obtained using acoustic coupling agar gel together with PMP wrap.ConclusionWhen using acoustic coupling polymer gel, artifacts may have prevented accurate visualization over an area that is approximately 0.6–0.7 mm thick. This shows that when intraoral ultrasound is performed by this method, it may not be possible to accurately visualize the mucosal epithelium.

A new potential polymeric cladding material for polycarbonate fibre optic core for high temperature use

The selection of a suitable cladding material for a fibre optic is crucial, and the application of polymeric material in high temperature conditions is garnering much attention from many researchers. However, polymer suffers from a weak thermal resistance, limiting its use in high temperature conditions. Therefore, this study aims to develop a new potential cladding material that has a good balance between optical and thermal properties. Two sets of cladding materials are proposed, namely the blend of polycarbonate/polymethyl methacrylate (PC/PMMA) and polymethylpentene (PMP). The cladding materials were dissolved in different solvents, followed by the casting on a glass plate to form a flat sheet cladding layer. PC/PMMA blend showed a miscible blending with a single Tg value and physical blending. Both PC/PMMA blend and PMP claddings demonstrated more than 90% of luminous transparency. The materials also showed high thermal stability with the onset degradation temperature of ∼ 300 °C. The optimum ratio for PC/PMMA was 80/20. Next, the cladding layer was fabricated by coating the core in 80/20 PC/PMMA and PMP. The scanning electron microscopy (SEM) image reveals that core–clad ratio for the PC fibre is 1.02 for both materials. The maximum tensile strength for the PC with PMP cladding was higher than that of the PC with PC/PMMA cladding. PMP-clad fibre has higher power output, which was a 60% increment from bare PC fibre output compared to PC/PMMA-clad fibre, with only 28.8% power output increment. Though both materials have huge potential to be used as the cladding for PC core, PMP cladding showed superior performance compared to PC/PMMA cladding.

Gamma-Ray Attenuation and Exposure Buildup Factor of Novel Polymers in Shielding Using Geant4 Simulation.

Polymers are often used in medical applications, therefore, some novel polymers and their interactions with photons have been studied. The gamma-ray shielding parameters for Polymethylpentene (PMP), Polybutylene terephthalate (PBT), Polyoxymethylene (POM), Polyvinylidenefluoride (PVDF), and Polychlorotrifluoroethylene (PCTFE) polymers were determined using the Geant4 simulation and discussed in the current work. The mass attenuation coefficients (μ/ρ) were simulated at low and high energies between 0.059 and 1.408 MeV using different radionuclides. The accuracy of the Geant4 simulated results were checked with the XCOM software. The two different methods had good agreement with each other. Exposure buildup factor (EBF) was calculated and discussed in terms of polymers under study and photon energy. Effective atomic number (Zeff) and electron density (Neff) were calculated and analyzed at different energies. Additionally, the half-value layer (HVL) of the polymers was evaluated, and the results of this parameter showed that PCTFE had the highest probability of interaction with gamma photons compared to those of the other tested polymers.

Electron Microscopic Confirmation of Anisotropic Pore Characteristics for ECMO Membranes Theoretically Validating the Risk of SARS-CoV-2 Permeation.

The objective of this study is to clarify the pore structure of ECMO membranes by using our approach and theoretically validate the risk of SARS-CoV-2 permeation. There has not been any direct evidence for SARS-CoV-2 leakage through the membrane in ECMO support for critically ill COVID-19 patients. The precise pore structure of recent membranes was elucidated by direct microscopic observation for the first time. The three types of membranes, polypropylene, polypropylene coated with thin silicone layer, and polymethylpentene (PMP), have unique pore structures, and the pore structures on the inner and outer surfaces of the membranes are completely different anisotropic structures. From these data, the partition coefficients and intramembrane diffusion coefficients of SARS-CoV-2 were quantified using the membrane transport model. Therefore, SARS-CoV-2 may permeate the membrane wall with the plasma filtration flow or wet lung. The risk of SARS-CoV-2 permeation is completely different due to each anisotropic pore structure. We theoretically demonstrate that SARS-CoV-2 is highly likely to permeate the membrane transporting from the patient’s blood to the gas side, and may diffuse from the gas side outlet port of ECMO leading to the extra-circulatory spread of the SARS-CoV-2 (ECMO infection). Development of a new generation of nanoscale membrane confirmation is proposed for next-generation extracorporeal membrane oxygenator and system with long-term durability is envisaged.

Design of acoustic Fresnel zone plate for contact stress measurement of aero-engine rotor mating surface

• PR-FZP made of non-metallic materials with the acoustic impedance closer to that of water all have a strong focusing ability. • Adding matching layers can improve the focus gain of PR-FZP to a certain extent. • Adding a reflecting layer can significantly improve the focus gain of PR-FZP. Accurate measurement of the contact stress on the mating surface of the core engine's multi-stage rotor is of great significance for improving the structural connection quality and comprehensive performance of aero-engines. The phase reversal Fresnel zone plate (PR-FZP) can realize the focusing of ultrasonic wave and its focusing ability has an important influence on the measurement accuracy of contact stress based on ultrasonic method. To improve the focusing ability of PR-FZP, this paper compares the focusing effect of PR-FZP made of different materials and designs PR-FZP with different structures based on the in-depth analysis of the focusing principle of PR-FZP. Numerical simulation results show that among the six selected materials, the single material PR-FZP made of polymethyl pentene (PMP) is always the highest with the change of working conditions. For PR-FZP with matching layer structure (M-PR-FZP), the focus gain is 0.21 dB higher than that of PR-FZP made of a single material. The focus gain of PR-FZP with reflecting layer structure (R-PR-FZP) can reach 24.84 dB, which is 6.01 dB and 1.45 dB higher than that of single metal (brass) Soret Fresnel zone plate (Soret FZP) and single non-metallic material (PMP) PR-FZP, respectively. This study has important guiding significance for improving the focusing ability of PR-FZP and realizing the accurate measurement of contact stress of aero-engine rotor mating surface.