Polyelectrolyte Multilayer Films Research Articles

Single-Molecule Fluorescence Imaging of DNA at a Potential-Controlled Interface

Many interfacial chemical phenomena are governed in part by electrostatic interactions between polyelectrolytes and charged surfaces; these phenomena can influence the performance of biosensors, adsorption of natural polyelectrolytes (humic substances) on soils, and production of polyelectrolyte multilayer films. In order to understand electrostatic interactions that govern these phenomena, we have investigated the behavior of a model polyelectrolyte, 15 kbp fluorescently labeled plasmid DNA, near a polarized indium tin oxide (ITO) electrode surface. The interfacial population of DNA was monitored in situ by imaging individual molecules through the transparent electrode using total-internal-reflection fluorescence microscopy. At applied potentials of +0.8 V versus Ag/AgCl, the DNA interfacial population near the ITO surface can be increased by 2 orders of magnitude relative to bulk solution. The DNA molecules attracted to the interface do not adsorb to ITO, but rather they remain mobile with a diffusion coefficient comparable to free solution. Ionic strength strongly influences the sensitivity of the interfacial population to applied potential, where the increase in the interfacial population over a +300 mV change in potential varies from 20% in 30 mM ionic strength to over 25-fold in 300 μM electrolyte. The DNA accumulation with applied potential was interpreted using a simple Boltzmann model to predict average ion concentrations in the electrical double layer and the fraction of interfacial detection volume that is influenced by applied potential. A Gouy-Chapman model was also applied to the data to account for the dependence of the ion population on distance from the electrode surface, which indicates that the net charge on DNA responsible for interactions with the polarized surface is low, on the order of one excess electron. The results are consistent with a small fraction of the DNA plasmid being resident in the double-layer and with counterions screening much of the DNA excess charge.

Polyelectrolyte/silver nanocomposite multilayer films as multifunctional thin film platforms for remote activated protein and drug delivery

We demonstrate a nanoparticle loading protocol to develop a transparent, multifunctional polyelectrolyte multilayer film for externally activated drug and protein delivery. The composite film was designed by alternate adsorption of poly(allylamine hydrochloride) (PAH) and dextran sulfate (DS) on a glass substrate followed by nanoparticle synthesis through a polyol reduction method. The films showed a uniform distribution of spherical silver nanoparticles with an average diameter of 50±20nm, which increased to 80±20nm when the AgNO3 concentration was increased from 25 to 50mM. The porous and supramolecular structure of the polyelectrolyte multilayer film was used to immobilize ciprofloxacin hydrochloride (CH) and bovine serum albumin (BSA) within the polymeric network of the film. When exposed to external triggers such as ultrasonication and laser light the loaded films were ruptured and released the loaded BSA and CH. The release of CH is faster than that of BSA due to a higher diffusion rate. Circular dichroism measurements confirmed that there was no significant change in the conformation of released BSA in comparison with native BSA. The fabricated films showed significant antibacterial activity against the bacterial pathogen Staphylococcus aureus. Applications envisioned for such drug-loaded films include drug and vaccine delivery through the transdermal route, antimicrobial or anti-inflammatory coatings on implants and drug-releasing coatings for stents.

Visible‐Light‐Induced Disruption of Diselenide‐Containing Layer‐by‐Layer Films: Toward Combination of Chemotherapy and Photodynamic Therapy

A photoresponsive polyelectrolyte multilayer film containing a diselenide functional group is fabricated using an unconventional layer-by-layer method. The polycation backbone is constructed through copolymerization of di-(1-hydroxylundecyl) diselenide and 1,4-bis(2-hydroxyethyl)piperazine with 2,4-diisocyanatotoluene. A common polyanion poly(styrene sulfonate) is selected as the polyanion. The obtained film can be gradually disrupted under the irradiation of mild visible light, and this process can be monitored with UV-vis spectroscopy. The residue of the film is estimated to be 17% after 5 h of irradiation. The intensity of the visible light can be as low as 50 mW cm⁻², which is even weaker than the sunlight. The cytotoxicity of the building blocks is evaluated in MTT assays using human hepatic cell line (L-02), and the results are satisfactory. Further tests show that cells can grow in a regular manner on this film, indicating good biocompatibility. In addition, the film can be used to achieve cargo loading and controlled release. Considering that light can not only trigger controlled release but also act as part of the therapy itself (photodynamic therapy), this system shows hope for further development into a platform for the combination of chemotherapy and photodynamic therapy, especially for applications concerning skin.

Molecular Weight Dependence on the Disintegration of Spin-Assisted Weak Polyelectrolyte Multilayer Films

We present the effect of molecular weight (MW) of polyelectrolytes (PEs) on the disintegration behavior of weak PE multilayer films consisting of linear poly(ethylene imine) (LPEI) and poly(methacrylic acid) (PMAA). The multilayer films prepared by the spin-assisted layer-by-layer deposition have well-ordered internal structures and also show the linear thickness growth behavior regardless of MWs of PMAA. The well-defined weak PE multilayer films were subject to disintegration into bulk solution when the electrostatic interactions between LPEI and PMAA layers were reduced by treatment at pH 2. However, we demonstrated the change in the disintegration mode and kinetics (i.e., from burst erosion to controlled surface erosion) as a function of MW of PMAA based on neutron reflectivity and quartz crystal microbalance with dissipation, revealing the correlation between the structural changes and the viscoelastic responses of the weak PE films upon pH treatment. Also, the unique swelling behavior as well as the ...

Encapsulation and surface charge manipulation of organic and inorganic colloidal substrates by multilayered polyelectrolyte films

Employing layer-by-layer (LbL) technique we could encapsulate both organic and inorganic nano- and microparticulate substrates by multilayer polyelectrolyte films of variable thicknesses. It has been observed that the uniformity of the polyelectrolyte multilayer does not depend severely on the chemical nature of particulate substrate; rather it depends on the initial surface charge density or ζ-potential of their bare surface. Higher ζ-potential of organic albumin nanoparticles helps to keep the polyelectrolyte chains unfolded. On the other hand, a lower ζ-potential of inorganic microparticles such as SiO2 induces a folding of dangling polyelectrolyte chains, forming domains of their aggregates or complexes at the particle surface, making the encapsulating multilayer inhomogeneous.

Adsorbed BMP-2 in polyelectrolyte multilayer films for enhanced early osteogenic differentiation of mesenchymal stem cells

The present work was focused on the development of multilayer films to adsorb and stabilize growth factors initially for delivery to mesenchymal stem cells (MSCs). The multilayer was constructed by poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS) via layer-by-layer assembly. The adsorption and bioactivity of bone morphogenetic protein 2 (BMP-2) in the films were explored. Then, the response of MSCs to the adsorbed BMP-2 was evaluated. It was demonstrated that the adsorbed BMP-2 could retain its activity toward enhanced early osteogenic differentiation of MSCs. Alkaline phosphatase (ALP) activity of MSCs seeded on the BMP-2 loaded film was even higher than that on the non-loaded film with BMP-2 added to the culture media. The results confirmed that a localized and sustained delivery of BMP-2 was more effective in vivo. It is noteworthy that these films can be deposited on a wide range of substrates with different shapes, sizes and composition, and can load other growth factors for facilitating stem cell differentiation toward specific lineages. Thus, such a system may find diverse applications in local delivery of immobilized growth factors for medical implants and for tissue-engineered constructs.

The stability of BMP loaded polyelectrolyte multilayer coatings on titanium

Immobilization of bone morphogenetic proteins (BMP) onto material surfaces is a promising, but still challenging, strategy for achieving dependable and consistent osseointegration of long-term metal implants. In the present study, we have developed an osteoinductive coating of a porous titanium implant using biomimetic polyelectrolyte multilayer (PEM) films loaded with BMP-2. The amount of BMP-2 loaded in these films was tuned – over a large range – depending on the cross-linking extent of the film and of the BMP-2 initial concentration. The air-dried PEM films were stable for at least one year of storage at 4 °C. In addition, they resisted exposure to γ-irradiation at clinically approved doses. The preservation of the growth factor bioactivity upon long-term storage and sterilization were evaluated both in vitro (using C2C12 cells) and in vivo (in a rat ectopic model) for the perspective of industrial and clinical development. BMP-2 loaded in dried PEM films exhibited shelf-life stability over one year. However, their bioactivity in vitro decreased from 50 to 80% after irradiation depending on the γ-irradiation dose. Remarkably, the in vivo studies showed that the osteoinductive potential of BMP-2 contained in PEM-coated Ti implants was fully preserved after air-drying of the implants and sterilization at 25 kGy. Film drying or irradiation did not affect the amount of new bone tissue formation. This “off-the-shelf” novel technology of functionalized implants opens promising applications in prosthetic and tissue engineering fields.

Thickness and morphology of polyelectrolyte coatings on silica surfaces before and after protein exposure studied by atomic force microscopy

Analyte–wall interaction is a significant problem in capillary electrophoresis (CE) as it may compromise separation efficiencies and migration time repeatability. In CE, self-assembled polyelectrolyte multilayer films of Polybrene (PB) and dextran sulfate (DS) or poly(vinylsulfonic acid) (PVS) have been used to coat the capillary inner wall and thereby prevent analyte adsorption. In this study, atomic force microscopy (AFM) was employed to investigate the layer thickness and surface morphology of monolayer (PB), bilayer, (PB-DS and PB-PVS), and trilayer (PB-DS-PB and PB-PVS-PB) coatings on glass surfaces. AFM nanoshaving experiments providing height distributions demonstrated that the coating procedures led to average layer thicknesses between 1nm (PB) and 5nm (PB-DS-PB), suggesting the individual polyelectrolytes adhere flat on the silica surface. Investigation of the surface morphology of the different coatings by AFM revealed that the PB coating does not completely cover the silica surface, whereas full coverage was observed for the trilayer coatings. The DS-containing coatings appeared on average 1nm thicker than the corresponding PVS-containing coatings, which could be attributed to the molecular structure of the anionic polymers applied. Upon exposure to the basic protein cytochrome c, AFM measurements showed an increase of the layer thickness for bare (3.1nm) and PB-DS-coated (4.6nm) silica, indicating substantial protein adsorption. In contrast, a very small or no increase of the layer thickness was observed for the PB and PB-DS-PB coatings, demonstrating their effectiveness against protein adsorption. The AFM results are consistent with earlier obtained CE data obtained for proteins using the same polyelectrolyte coatings.

Development of polyelectrolyte multilayer thin film composite membrane for water desalination application

Thin film composite membranes were fabricated via spin assisted layer by layer (SA-LbL) assembly by depositing alternate layers of poly(allyl amine hydrochloride) (PAH) and poly(acrylic acid) (PAA) on a polysulfone (PSF) ultrafiltration membrane as support. The suitability of these membranes for potential water purification applications was explored by testing the stability of the deposited thin films and their permeation characteristic using cross-flow permeation cell. Permeation test conducted at a pressure of 40bar, temperature of 25°C, pH of 6 and feed water concentration of 2000ppm NaCl demonstrated that the PAH/PAA multilayer film deposited on polysulfone support remained stable and intact under long-term test conditions. The 120 bilayers of PAH/PAA membrane tested at the above condition showed flux of 15L/m2.h and salt rejection of 65%. The membrane performance evaluation also revealed that SA-LbL PAH/PAA membrane follows the characteristics of the solution diffusion membrane.

Chitosan/alginate multilayer film for controlled release of IDM on Cu/LDPE composite intrauterine devices

To reduce such side effects as pain and bleeding caused by copper-containing intrauterine device (Cu-IUD), a novel medicated intrauterine device, which is coated with an indomethacin (IDM) delivery system on the surface of copper/low-density polyethylene (Cu/LDPE) composite intrauterine device, has been proposed and developed in the present work. The IDM delivery system is a polyelectrolyte multilayer film, which is composed of IDM containing chitosan and alginate layer by layer, is prepared by using self-assembled polyelectrolyte multilayer method, and the number of the layers of this IDM containing chitosan/alginate multilayer film can be tailored by controlling the cyclic repetition of the deposition process. After the IDM containing chitosan/alginate multilayer film is obtained on the surface of Cu/LDPE composite intrauterine device, its release behavior of both IDM and cupric ion has been studied in vitro. The results show that the release duration of IDM increase with the increasing of thickness of the IDM containing chitosan/alginate multilayer film, and the initial burst release of cupric ion cannot be found in this novel medicated Cu/LDPE composite IUD. These results can be applied to guide the design of novel medicated Cu-IUD with minimal side effects for the future clinical use.

Nanoparticle Film Assemblies as Platforms for Electrochemical Biosensing—Factors Affecting the Amperometric Signal Enhancement of Hydrogen Peroxide

Factors affecting the enhanced amperometric signal observed at electrodes modified with polyelectrolyte-gold nanoparticle (Au-NP) composite films, which are potential interfaces for first-generation biosensors, were systematically investigated and optimized for hydrogen peroxide (H2O2) detection. Polyelectrolyte multilayer films embedded with citrate-stabilized gold nanoparticles exhibited high sensitivity toward the oxidation of H2O2. From this Au-NP film assembly, the importance of Au-NP ligand protection, film permeability, the density of Au-NPs within the film, and electronic coupling between Au-NPs (interparticle) and between the film and the electrode (interfacial) were evaluated. Using alternative Au-NPs, including those stabilized with thiols, polymers, and bulky ligands, suggests that the amperometric enhancement of H2O2 is optimized at poly-L-lysine-linked film assemblies embedded with Au-NPs possessing small, charged, and conductive (conjugated) peripheral ligands. As a potential application of these Au-NP film assemblies, an enhanced amperometric signal for H2O2 oxidation was shown for modified "needle" electrodes. The overall aim of this research is to gain a greater understanding of designing electrochemical sensing strategies that incorporate Au-NPs and target specific analytes.

Study of the platinum nanoparticle synthesis in polyelectrolyte multilayer films and their electrical and morphological surface properties

Study of the platinum nanoparticle synthesis in polyelectrolyte multilayer films and their electrical and morphological surface properties

Increased protein sorption in poly(acrylic acid)-containing films through incorporation of comb-like polymers and film adsorption at low pH and high ionic strength.

In principle, incorporation of comb-like block copolymers in multilayer polyelectrolyte films can both increase film thickness relative to coatings containing linear polymers and provide more swollen films for increased sorption of proteins. In the absence of added salt, alternating adsorption of 5 bilayers of protonated poly(allylamine) (PAH) and comb-like poly(2-hydroxyethyl methacrylate)-graft-poly(acrylic acid) (PHEMA-g-PAA) leads to ∼2-fold thicker coatings than adsorption of PAH and linear PAA, and the difference in the thicknesses of the two coatings increases with the number of bilayers. Moreover, the (PAH/PHEMA-g-PAA)n films sorb 2- to 4-fold more protein than corresponding films prepared with linear PAA, and coatings deposited at pH 3.0 sorb more protein than coatings adsorbed at pH 5.0, 7.0, or 9.0. In fact changes in deposition pH and addition of 0.5 M NaCl to polyelectrolyte adsorption solutions alter protein sorption more dramatically than variations in the constituent polymer architecture. When deposited from 0.5 M NaCl at pH 3.0, both (PAH/PHEMA-g-PAA)5 and (PAH/PAA)5 films increase in thickness more than 400% upon adsorption of lysozyme. These films contain a high concentration of free -COOH groups, and subsequent deprotonation of these groups at neutral pH likely contributes to increased protein binding. Lysozyme sorption stabilizes these films, as without lysozyme films deposited at pH 3.0 from 0.5 M NaCl desorb at neutral pH. Films deposited at pH 9.0 from 0.5 M NaCl are more stable and also bind large amounts of lysozyme. The high binding capacities of these films make them attractive for potential applications in protein isolation or immobilization of enzymes.

Bioaffinity Sensor Based on Nanoarchitectonic Films: Control of the Specific Adsorption of Proteins through the Dual Role of an Ethylene Oxide Spacer

The identification and quantification of biomarkers or proteins is a real challenge in allowing the early detection of diseases. The functionalization of the biosensor surface has to be properly designed to prevent nonspecific interactions and to detect the biomolecule of interest specifically. A multilayered nanoarchitecture, based on polyelectrolyte multilayers (PEM) and the sequential immobilization of streptavidin and a biotinylated antibody, was elaborated as a promising platform for the label-free sensing of targeted proteins. We choose ovalbumin as an example. Thanks to the versatility of PEM films, the platform was built on two types of sensor surface and was evaluated using both optical- and viscoelastic-based techniques, namely, optical waveguide lightmode spectroscopy and the quartz crystal microbalance, respectively. A library of biotinylated poly(acrylic acids) (PAAs) was synthesized by grafting biotin moieties at different grafting ratios (GR). The biotin moieties were linked to the PAA chains through ethylene oxide (EO) spacers of different lengths. The adsorption of the PAA-EOn-biotin (GR) layer on a PEM precursor film allows tuning the surface density in biotin and thus the streptavidin adsorption mainly through the grafting ratio. The nonspecific adsorption of serum was reduced and even suppressed depending on the length of the EO arms. We showed that to obtain an antifouling polyelectrolyte the grafting of EO9 or EO19 chains at 25% in GR is sufficient. Thus, the spacer has a dual role: ensuring the antifouling property and allowing the accessibility of biotin moieties. Finally, an optimized platform based on the PAA-EO9-biotin (25%)/streptavidin/biotinylated-antibody architecture was built and demonstrated promising performance as interface architecture for bioaffinity sensing of a targeted protein, in our case, ovalbumin.

Synthesis and tribological properties of CuS/ZnS nanoparticles doped polyelectrolyte multilayers

Polyelectrolyte multilayer thin films [poly(diallyl dimethylammonium chloride) (PDDA) and poly(acrylic acid) (PAA)] for the synthesis of CuS and ZnS nanoparticles were prepared. The CuS/ZnS nanoparticles in situ synthesised by immersing the PDDA/PAA polyelectrolyte multilayer thin films into Cu2+(or Zn2+) and Na2S aqueous solutions alternately, which were characterised in detail by UV visible absorption spectroscopy, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. The CuS and ZnS nanoparticles doped polyelectrolyte multilayer thin films were synthesised by the layer-by-layer molecular deposition technology and in situ synthesis method. The coefficient of friction (COF) decreased with the in situ synthesis CuS and ZnS nanoparticles doped into the polyelectrolyte layers. The in situ nanoparticles exhibited enhanced wear resistance performance of the plain polyelectrolyte multilayers.

The Effect of Heparin-VEGF Multilayer on the Biocompatibility of Decellularized Aortic Valve with Platelet and Endothelial Progenitor Cells

The application of polyelectrolyte multilayer films is a new, versatile approach to surface modification of decellularized tissue, which has the potential to greatly enhance the functionality of engineered tissue constructs derived from decellularized organs. In the present study, we test the hypothesis that Heparin- vascular endothelial growth factor (VEGF) multilayer film can not only act as an antithrombotic coating reagent, but also induce proliferation of endothelial progenitor cells (EPCs) on the decellularized aortic heart valve. SEM demonstrated the adhesion and geometric deformation of platelets. The quantitative assay of platelet activation was determined by measuring the production of soluble P-selectin. Binding and subsequent release of heparin and VEGF from valve leaflets were assessed qualitatively by laser confocal scanning microscopy and quantitatively by ELISA methods. Human blood derived EPCs were cultured and the adhesion and growth of EPCs on the surface modified valvular scaffolds were assessed. The results showed that Heparin-VEGF multilayer film improved decellularized valve haemocompatibility with respect to a substantial reduction of platelet adhesion. Release of VEGF from the decellularized heart valve leaflets at physiological conditions was sustained over 5 days. In vitro biological tests demonstrated that EPCs achieved better adhesion, proliferation and migration on the coatings with Heparin-VEGF multilayer film. Combined, these results indicate that Heparin-VEGF multilayer film could be used to cover the decellularized porcine aortic valve to decrease platelet adhesion while exhibiting excellent EPCs biocompatibility.

Polyelectrolyte modification of ultrafiltration membrane for removal of copper ions

Alternating electrostatic adsorption of polyanions and polycations onto porous substrates, using the layer-by-layer technique, provides a convenient way to modify ultrafiltration membranes. That is why polyethersulfone ultrafiltration membranes have been coated by alternating deposition of poly(allylamine hydrochloride) and poly(acrylic acid) to modify the membranes by a thin polyelectrolyte multilayer film. The polyelectrolyte-modified membranes were characterized by using infrared spectroscopy, water angle measurements and laser reflectometry. In an attempt to develop membrane modification as a new alternative method allowing the removal of heavy metal ions by ultrafiltration, these modified membranes were used to perform the filtration of aqueous solutions contaminated by copper (II) cations. These filtration experiments led to a good retention of the copper ions by the modified membranes, thus proving the usefulness of polyelectrolytes adsorption on organic membranes. It also demonstrated the importance of several operating conditions including: polyelectrolyte concentration, polyelectrolyte pH, polyelectrolyte multilayer film thickness, number of polyelectrolyte layers and pH of copper solutions.

Reversing charges or how to improve Wharton's jelly mesenchymal stem cells culture on polyelectrolyte multilayer films

Polyelectrolyte multilayer (PEMs) films made of poly(allylamine hydrochloride) (PAH) as polycation and poly(styrene sulfonate) (PSS) as polyanion, with a PAH ending layer, can be used as a coating in order to improve the anti-thrombogenicity and patency of vascular grafts in vascular engineering field. They induce strong adhesion of mature endothelial cells on glass, expanded polytetrafluoroethylene and cryopreserved arteries. Despite their outstanding effect on mature and progenitor endothelial cells, PEMs ending with PAH showed a poor outcome on Wharton's jelly mesenchymal stem cells (WJ-MSCs) culture. The aim of this work was to examine the influence of the ending charge of PEMs on WJ-MSCs behavior. WJ-MSCs amplified until the 3rd passage were seeded and cultured on (PAH-PSS)3-PAH and on (PAH-PSS)4 coated glass for 10 days. Stem cell phenotype was checked by flow cytometry and cell morphology was followed by bright field microscopy. Flow cytometry analysis showed that WJ-MSCs were positive for MSC's markers CD73, CD90 and CD105 and negative for hematopoietic markers CD34 and CD45. Light microscopy showed development of nodule-like structures after 10 days of culture on (PAH-PSS)3-PAH, which resulted in a disturbance of cell monolayer. Whereas WJ-MSCs cultured on (PAH-PSS)4 ending with PSS showed a normal cell growth like on collagen and reached confluence after 10 days. The culture surface seems to have a determining role in WJ-MSC's "spatial" behavior, which could be considered in the field of tissue engineering.

Brillouin spectroscopy: A new tool to decipher viscoelastic properties of biological scaffold functionalized with nanoscale films

In tissue engineering, the endothelialization of vascular scaffold can be a crucial step to improve graft patency. A functional cellularization requires coating surfaces. Since 2003, our group used polyelectrolyte multilayer films (PEMFs) made of poly(allylamine hydrochloride) and polystyren sulfonate to coat luminal surface of blood vessel. Previous results showed that PEMFs have remarkable effect on cellular behavior: adhesion, proliferation, differentiation. However, no method seems adapted for in vitro measurement of the viscoelastic shift after PEMFs buildup. In this present work, we proposed to use a new analytical method based on Brillouin spectroscopy (BS) to investigate the influence PEMFs coating on vessel intrinsic viscoelasticy. On human umbilical arteries and rabbit vessels, PEMFs were buildup and the luminal surfaces viscoelasticy were measuring by BS. It seems that these films do not alter dynamic functionality and BS could be an interesting method for understanding the role of the tissue architecture, the interrelation between the different structures constituting the wall and the influence of this architecture on the tissue behavior, especially with the characterized components of the different vascular wall. The ability of BS to characterize biological samples opens potential applications in tissue engineering field, especially as a tool for a better understanding of vascular diseases.

Influence of serum percentage on the behavior of Wharton's jelly mesenchymal stem cells in culture

Mesenchymal stem cells (MSCs) are multipotent cells able to differentiate into several lineages with valuable applications in regenerative medicine. MSCs differentiation is highly dependent on physicochemical properties of the culture substrate, cell density and on culture medium composition. In this study, we assessed the influence of fetal bovine serum (FBS) level on Wharton's jelly (WJ)-MSCs behavior seeded on polyelectrolyte multilayer films (PEMF) made of four bilayers of poly-allylamine hydrochloride (PAH) as polycation and poly-styrene sulfonate (PSS) as polyanion. MSCs isolated from WJ by explants method were amplified until the third passage. Their phenotypic characterization was performed by flow cytometry analyses. MSCs were seeded on PEMF, in Endothelial growth medium-2 (EGM-2) supplemented by either 5% or 2% FBS. Cell's behavior was monitored for 20 days by optical microscopy and immunofluorescence. Until 2 weeks on glass slides, no difference was observed whatever the FBS percentage. Then with 5% FBS, MSCs formed three-dimensional spheroids on PSS/PAH after 20 days of culture with a nuclear aggregate. Whereas, with 2% FBS, these spheroids did not appear and cells grown in 2D conserved the fibroblast-like morphology. The decrease of FBS percentage from 5% to 2% avoids 3D cell spheroids formation on PAH/PSS. Such results could guide bioengineering towards building 2D structures like cell layers or 3D structures by increasing the osteogenic or chondrogenic differentiation potential of MSCs.