Precipitation Of Phase Research Articles

Phase Preparation of Xiao-chai-hu Decoction and its Pharmacodynamics of Acute Liver Injury.

Self-emulsifying nano-phase of traditional Chinese medicine are a research hotspot. Xiao-Chai-Hu decoction is a commonly used compound decoction in clinical practice, which is of great research significance. The aim of this study was to isolate and characterize the self-emulsifying nano-phase and other phases of Xiao-Chai-Hu decoction, and to study the effects of each phase on acute liver injury. The liquid medicine was prepared employing centrifugation followed by dialysis. Single- factor investigation methodology was utilized to optimize the preparation parameters for both phases. Characterization of the formulated phase involved analyses such as surface morphology assessment, measurement of nanoparticle size and Zeta potential using an analyzer, observation of the Tyndall effect, conducting diffusion and dilution tests, examination under a microscope, and structural visualization via transmission electron microscopy (TEM). Furthermore, an acute liver injury model was established in rats through intraperitoneal injection of D-Galactosamine (D-Gal- N). To assess hepatic function and oxidative stress status, serum levels of alanine aminotransferase (ALT) and aspartate aminotransferase (AST), superoxide dismutase (SOD) activity, and malondialdehyde (MDA) content in liver tissue were quantified. The liver coefficients for each group were calculated as an additional parameter. For histopathological evaluation, liver tissue sections from the experimental group were stained with Hematoxylin and Eosin (H&E) and examined microscopically under light conditions. These revisions aim to enhance clarity, correct minor grammatical errors (such as capitalization of "HE" to "H&E"), and ensure a smoother flow of information without altering the scientific content of your original text. Successful establishment and separation of four distinct phases were achieved, including the self-emulsifying nano-phase, precipitation phase, suspension phase, and true solution phase. The self-emulsifying nano-phase was characterized as spherical particles with an average diameter of approximately 100 nm. Pharmacodynamic assessments revealed that both Xiao-Chai-Hu decoction and its self-emulsifying nano-phase significantly reduced liver coefficients and alanine aminotransferase (ALT) levels compared to controls (P<0.05). However, no statistically significant differences were observed in regards to aspartate aminotransferase (AST) concentrations, malondialdehyde (MDA) content, or superoxide dismutase (SOD) activity between the treatment groups and control (P>0.05). These findings indicate that both Xiao-Chai-Hu decoction and its self-emulsifying nano-formulation ameliorated D-GalN-induced acute liver injury, albeit without statistically distinguishable efficacy between them (P>0.05). The presence of a self-emulsifying nano-phase within Xiao-Chai-Hu decoction is confirmed, and this nano-phase emerges as a therapeutically efficacious component in mitigating acute liver injury.

In vitro digestion study comparing a predigested glycerolysis product versus long-chain polyunsaturated fatty acid-rich oils (LCPUFA) as a strategy for administering LCPUFA to preterm neonates

Background & aimsMaintaining an adequate supply of arachidonic acid (ARA) and docosahexaenoic acid (DHA) is essential for optimal growth of preterm infants. This study aims to evaluate and compare the digestibility and bioaccessibility of ARA and DHA oils compared to their predigested product through an in vitro digestion model. MethodsAn in vitro gastrointestinal digestion model was used in two stages: gastric digestion and intestinal digestion. Samples of two polyunsaturated rich oils (ARA and DHA oils) and their predigested product (2:1, ARA: DHA) produced by enzymatic glycerolysis have been digested for 120 min. The final digestion product obtained was composed of three phases: an upper oily phase (OP) containing the undigested species, an intermediate micellar phase (MP) containing digested and bioaccessible lipids, and a precipitate phase (PP) with insoluble compounds. The reaction was monitored by taking aliquots and their subsequent lipid extraction and analysis. ResultsPoorer digestibility for ARA and DHA oils was observed based on the percentage of the oily phase (26.7% and 20%, respectively) found compared to the glycerolysis product (GP) oily phase (13.9%). The highest micellar phase was found in the GP (approx. 83%). On the other hand, the monoglyceride (MAG) content was lower in the digestion product (DP) from ARA and DHA oils, 4.3% and 9.2%, respectively, compared to the MAG observed in the DP of GP (15%). ConclusionConsidering the percentage of oily phase, micellar phase, and the MAG content, it can be concluded that the GP is more digestible and ARA and DHA are more bioaccessible than in its precursor oils.

Thermal stability of a newly developed Mn containing β-solidifying γ-TiAl intermetallic compound at 750 °C

A newly low-cost β-solidifying γ-TiAl alloy Ti-44Al-3Mn-0.4Mo-0.4W-0.1B-0.1C (in at. %, named as TMMW) was invented. The rolled bars with a diameter of 12 mm were successfully fabricated by conventional hot rolling process, directly carrying out from the ingot without the pre-forging or hot-packing. The heat-treated TMMW rolled bar, which had a fine-grained nearly lamellar (NL) microstructure, was then air-exposed at 750 °C for up to 3000 h. The changes of the microstructure during this exposure were characterized using electron probe X-ray micro-analyzer (EPMA), transmission electron microscope (TEM), electron backscattered diffraction (EBSD) and high-energy X-ray diffraction (HEXRD). The tensile properties of the samples before and after thermal exposure were also tested. The fine-grained NL microstructure is found to be thermodynamically stable during the exposure. Meanwhile, the combined addition of Mo and W shows a positive effect on the stabilization of βo phase at colony boundaries, with only slight precipitation of the nanometer βo phases with no other brittle phases, such as Laves, in the metastable α2 lamellae. It is found that the thickness of the α2 lamellae decreases after 500 h exposure, while remains basically unchanged from 500 h to 3000 h, which is contributed by the effective pinning effect of the precipitated βo phase in α2 lamellae. As a result, the exposure-induced embrittlement under room temperature and elevated temperature does not take place. Interestingly, the ductility tested at 800 °C improves significantly after exposure. As for the tensile strength, it is only reduced by less than 10 % after 500 h exposure, while it remains essentially unchanged when increasing the exposure time from 500 h to 3000 h. Finally, the mechanisms of the precipitation of βo phases in the α2 lamellae and the tensile properties evolution during the exposure were carefully discussed.

Microstructure, hardness and creep properties for P91 steel after long-term service in a ultra-supercritical power plant

3 P91 pipes enduring 5∼6 × 104 h service had been found in an ultra-supercritical power plant. Hardness tests, microstructure observation(OM, SEM/EBSD, TEM/EDS) and creep rupture tests were performed, and the relationship between hardness, microstructure and creep rupture strength were discussed. Results showed that 1 of the 3 pipes still featured lath martensite, and its mechanical properties complied with relevant criteria. Other 2 pipes were characteristic of a mixture of ferrite and highly recovered martensite. Their hardness and creep rupture strength experienced severe degradation. Laves phase was observed in all 3 pipes. The most distinctive feature of the 2 low hardness pipes was their coarse and intragranularly distributed M23C6. This might be caused by abnormal heat treatments which could lead to the mixed microstructure of martensite and ferrite, and this kind of microstructure would degrade fast during service. Thus the low hardness had nothing to do with the precipitation of Laves phase.

Machine learning-assisted design of refractory high-entropy alloys with targeted yield strength and fracture strain

In order to improve the traditional “trial and error” material design method, machine learning-yield strength and machine learning-fracture strain models are incorporated into one system to predict yield strength and fracture strain in refractory high-entropy alloys (RHEAs) under compression. The ML-yield strength model and ML-fracture strain model achieve excellent predictions (R2 = 0.942, RMSE=0.35) and (R2 = 0.892, RMSE=0.41) in the testing set, respectively. Based on the machine learning model, Nb0.22Ta0.22Ti0.24V0.23W0.09, Nb0.24Ta0.22Ti0.26V0.04W0.24, Nb0.26Ta0.24Ti0.21V0.24W0.05, and Nb0.18Ta0.26Ti0.22V0.21W0.13 RHEAs in the Nb-Ta-Ti-V-W RHEA system were screened and synthesized. The yield strength (1915 MPa, 1983 MPa) of the Nb0.22Ta0.22Ti0.24V0.23W0.09 and Nb0.24Ta0.22Ti0.26V0.04W0.24 RHEAs are higher than that (1689 MPa) of the NbTaTiVW RHEA. The unfractured Nb0.18Ta0.26Ti0.22V0.21W0.13 and Nb0.26Ta0.24Ti0.21V0.24W0.05 RHEAs under compression exhibit superior performance than the fracture strain (16.6 %) of the NbTaTiVW RHEA. The mixing enthalpy of RHEAs is negatively correlated with the yield strength, whereas a negative relationship exists between electronegativity difference and fracture strain through the SHAP analysis. Decreasing the mixing enthalpy and increasing the electronegativity difference promote the formation of the precipitated phase. The electron probe microanalysis reveals that the differences in mechanical properties (yield strength and fracture strain) in the NbTaTiVW RHEAs primarily stem from the fraction of the precipitated phase.

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Zn microalloying made great contributions to microstructures evolution and performances enhancement. The effects of various contents of Zn on the precipitate microstructure, tensile property and corrosion behavior of Al-3.2Cu-1.5Li alloys with medium Cu/Li mass ratio were examined by tensile testing and corrosion measurement. Experimental results demonstrated that the tensile strength of the Zn microalloyed samples dropped slightly as the Zn content increased due to the number density of precipitates with minor size variation showed a downward trend within the grains. Corrosion testing revealed that the corrosion type of Zn microalloyed samples was primarily localized intragranular corrosion, slight intergranular corrosion and local pitting corrosion was also partially involved. The emergence of Zn element in grain boundary (GB) coarse (T1) phases and the suppressed precipitation of intragranular phases in the alloys with higher content Zn were found to reduce corrosion sensitivity with the increase of Zn content, which was ascribed to the decreased potential difference between the GB and adjacent matrix, and between the GB precipitates and precipitation free zone (PFZ).

Study on dynamic recrystallization and precipitation behavior of hot compressed Al-20Zn-0.5Mg-0.5Sc alloy

The dynamic recrystallization (DRX) behavior of the Al-20Zn-0.5Mg-0.5Sc alloy was investigated under specific conditions using a Gleeble-3500 thermal simulator. The resultant grain size, recrystallization degree and precipitated phases were studied. The results indicate that the sensitivity of DRX grain size is highly affected by temperature, feebly influenced by strain and intermediately affected by strain rate. The DRX grains are grown by an average of 3.49 μm with increasing temperature. The DRX behavior is sensitive to temperature, strain and strain rate, resulting in changes in average grain size, percentage of HAGBs and degree of recrystallization under different parameters. At 400 ℃ / 40 % / 0.1 s−1, the average grain size is refined to 12.90 μm, and the corresponding HAGBs and recrystallization degree are approximately 46.2 % and 34.3 %, respectively. The Al3Sc, Zn and η (MgZn2) phases are precipitated in the hot-compressed alloy. The Al3Sc phase promotes the precipitation of the Zn and η phases. The size, amount and morphology of Al3Sc, Zn and η phases at different parameters have an important influence on the movement of dislocations and nucleation of grains, which leads to changes in DRX grain size and the degree of recrystallization. The fine precipitated phase particles Al3Sc and η inhibit the growth of recrystallized grain by pinning grain boundaries and exerting a blocking force on dislocations. Dynamic precipitation is the dominant mechanism for the changes in DRX grain size and degree of recrystallization. To achieve the refined grains and homogeneous microstructures, the optimum parameters are recommended as 400 ℃, 0.1 s−1 and 50 %.

Tailoring the Crystalline structures and mechanical properties of IN718 alloy repaired by wire-fed electron beam directed energy deposition through a custom-designed heat treatment process

Wire-fed electron beam directed energy deposition (EB-DED) is a cost-effective technique for repairing damaged metal components. However, a large number of Laves phases precipitated in the deposited zone impair the mechanical properties of the repaired IN718 alloy parts. This study investigated the microstructural evolution and mechanical properties of IN718 alloy repaired by EB-DED, emphasizing a custom-designed heat treatment combining homogenization and double aging to enhance deformation coordination. Two homogenization durations, 15 min (HA15) and 60 min (HA60), were tested. The research utilized advanced characterization techniques, including scanning electron microscopy, electron backscatter diffraction, transmission electron microscopy, and digital image correlation, to analyze microstructural evolution and deformation behavior. These findings revealed that, in the as-repaired condition, the deposited zone exhibited columnar grains with inter-dendritic Laves phase, while the substrate zone contained equiaxed grains and δ phase precipitation at the grain boundaries. Post-HA treatment led to the dissolution of Laves and δ phases and the precipitation of γ'/γ'' strengthening phases. Furthermore, the HA60-repaired sample showed recrystallization in the deposited zone, markedly improving plastic deformation uniformity. Tensile tests exhibited that the HA samples achieved yield strength and elongation matching wrought standards, with ultimate tensile strength reaching 95 % of wrought values. This work presents a novel method for achieving high-quality repair in IN718 alloy, advancing the potential for broader industrial applications.

The effect of pre-heat parameters and final-heat parameters on microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

In this study, an ultra-high strength Mg-13Gd-4Y–0Zn-0.5Zr (wt.%) alloy with tensile yield strength (TYS) of 456 MPa and ultimate tensile strength (UTS) of 486 MPa was prepared by using different pre-heat parameters and subsequent final-heat treatment combined with backward extrusion (BE) deformation process. It was shown that the pre-heat teratment could significantly enhance the UTS and TYS of the secondary backward extruded (BEed) alloy compared with none treatment. The reason was that the pre-heat treatment promoted the particle stimulated nucleation (PSN) mechanism and continuous dynamic recrystallization (CDRX), significantly increasing the fraction of dynamic recrystallization (DRX). The strengthening of the secondary BEed alloy was attributed to the unique microstructure characteristics: (I) the fine DRXed grains pinned by dynamic precipitates, (II) the dense dynamic precipitation phases, (III) the effect of the fine-grain strengthening. However, the overly densely distributed second phase, which increased the local dislocation density due to the narrower spacing, made it difficult to prevent crack propagation and caused premature fracture of the alloy. In addition, the subsequent final-heat treatment also facilitated the precipitation of the second phases of the secondary BEed alloys and brought in the ultra-high mechanical properties.

Dynamic plastic deformation at liquid nitrogen temperature and aging effects on microstructure and properties of Cu-0.3Zr-0.15Cr alloys

The 9R phase is rarely formed in copper alloys because of its high stacking fault energy. In this study, we generated a large amount of 9R phase in Cu-0.3Zr-0.15Cr alloys by dynamic plastic deformation (DPD) at liquid nitrogen temperature for the first time, and revealed the transformation mechanism of 9R to nanotwins. The process of DPD + aging treatment enables the alloy to obtain excellent comprehensive properties (strength of 657 MPa, electrical conductivity of 75.2 % IACS, and elongation of 14.6 %), which are derived from the heterogeneous microstructure composed of ultrafine structures, coarse grains, and nano precipitated phases. In addition, we have evaluated the phase transformation kinetics after DPD at liquid nitrogen temperature. This work provides a new way to better understanding the microstructure transition and precipitation kinetics under dynamic plastic deformation with aging treatment at liquid nitrogen temperature.

Deposition of highly crystalline AlScN thin films using synchronized high-power impulse magnetron sputtering: From combinatorial screening to piezoelectric devices

With the integration of 5G in day-to-day devices and the foreseeable 6G revolution, demand for advanced radio frequency (RF) microelectromechanical systems (MEMS) is growing. Aluminum scandium nitride (AlScN) has emerged as the material of choice for many of those applications due to its superior piezoelectric and electromechanical properties compared to aluminum nitride (AlN). However, synthesizing high-quality, textured AlScN thin films is challenging. Alloying of Sc in AlN induces structural frustration leading to strain, defects, disoriented grains, and disrupted crystal symmetry during growth. Higher deposition temperatures, while improving crystalline quality, risk undesirable phase precipitation and limit industrial sustainability. In addition, future MEMS technologies also demand conformal and textured coatings over diverse topographies. Addressing these challenges collectively requires new and innovative synthesis approaches. In this study, we investigate the feasibility of ionized physical vapor deposition to deposit highly oriented AlScN films with minimal defects at lower temperatures. To this end, we employ combinations of different deposition approaches, such as metal-ion synchronized (MIS) high-power impulse magnetron sputtering (HiPIMS). Leveraging the high ionization rates of HiPIMS and optimally timed substrate bias potentials, we selectively bombard the growing film with Al and/or Sc ions to enhance the adatom mobility at low temperatures while simultaneously providing the ability to tune stress and coat complex structures conformally. The nonequilibrium solubility of Sc in wurtzite AlN under different conditions is investigated using a combinatorial deposition approach. Promising candidates with ∼20% Sc composition are isolated and characterized for crystallinity and residual stress. Disoriented grains, a significant issue in growing AlScN films, are observed through atomic force microscopy and found to be completely removed by substrate rotation and application of substrate biasing. The measured piezoelectric response of the films with approximately 20% Sc concentration ranges from 6.3 to 8.8 pm/V, in line with density functional theory predictions and experimentally reported values for films deposited in a production tool with coplanar geometry. At the same time, MIS-HiPIMS-deposited films offer unique properties and flexibility to tune their stress state and structural properties, thus presenting exciting opportunities for the fabrication of advanced RF filters and next-generation MEMS devices. Published by the American Physical Society 2024

Achieving high mechanical and corrosion properties of AA2050 Al-Li alloy: The creep aging under plastic loading

The influences of elastic/plastic loading (100–220 MPa) on the creep behavior, mechanical properties, and corrosion behavior of creep-aged AA2050 alloys were investigated. The results show that the creep rate increased from 0.35 % to 0.61 % with the increase of stress from 100 MPa to 220 MPa. The creep rate was increased rapidly under plastic loading (220 MPa) due to the increased dislocation density. Meanwhile, the plastic loading shortened the peak-aged time of creep-aged alloys and achieved outstanding strength (UTS=534 MPa, YS=496 MPa, peak aged), which increased by 33 MPa and 32 MPa compared with elastic loading, respectively. The strength enhancement was attributed to the increase in dislocation density, weak oriented precipitation effect, and dense precipitation of T1 phases. Additionally, compared with elastic loading, GBPs under plastic loading coarsened and distributed discretely, their elements content distributed evenly, and the Cu content increased. Therefore, the intergranular corrosion (IGC) depth and stress corrosion cracking (SCC) susceptibility index (ISSRT) decreased from 174 μm, and 8.7 % to 121 μm, and 5.9 %, respectively. These findings pave a way in breaking curvature limit of creep aging technology.

Effect of intermittent non-isothermal aging on the microstructure and properties of Al–Zn–Mg–Cu alloy

The proposition of an intermittent non-isothermal aging (IM-NIA) is an innovative approach to address the challenge of balancing the mechanical properties and corrosion resistance of Al–Zn–Mg–Cu alloys. The effects of IM-NIA on the hardness, corrosion resistance and microstructure morphology of Al–Zn–Mg–Cu alloys were investigated by hardness test, intergranular corrosion test (IGC), exfoliation corrosion test (EXCO), electrochemical corrosion test and combined with transmission electron microscopy (TEM) observation. The results showed that the hardness of the alloy was the highest at 186HV after intermittent post-tempering to 180 °C (IM-H180). The intergranular corrosion depth is the smallest, the corrosion rate is the slowest, and the exfoliation corrosion rating is EA. In addition, the alloy matrix precipitated phase has the smallest average diameter, the highest volume fraction, the strongest ability to repair the passivation film, and the strongest resistance to Cl− erosion; At the same time, the grain boundary precipitation phase is intermittent and multilinear parallel distribution, PFZ is the widest, hindering the anodic corrosion channel, slow corrosion progress and improve corrosion resistance.

Effect of multi-element synergistic addition on the microstructure evolution and performance enhancement of laser hot-wire cladded Fe-based alloy

To satisfy the requirements of hardness and corrosion resistance for laser additive manufacturing of hydraulic supports, this study applied the synergistic addition of C, B, Cr, Ni, Nb and Mo elements in Fe-based alloys. The multi-phases, martensite + austenite + ferrite were designed. The microstructure, hardness and corrosion resistance of the coatings were analyzed. Increasing the C and B contents could significantly increase the hardness of the coatings, while the corrosion resistance was decreased. The corrosion resistance of the coatings was determined by the Cr contents. However, increasing the Cr contents to 20.0 wt % resulted in the ferrite structure with lower hardness (21 HRC). The coatings with 0.25 wt % C, 1.2 wt % B and 19.0 wt % Cr showed the optimal matching of hardness (56 HRC) and corrosion resistance (survived in neutral salt spray test≥300h). The resulted coatings were mainly consisted of dendritic structure. Fine lath martensite phase was dominant in the dendrite regions. The interdendritic regions were consisted of nano-sized intermetallics with a mixture of σ+Nb + FeNb + Cr2Nb+(Fe,Cr)2B + NbC compounds. These interdendritic regions (14.2 GPa) showed higher hardness than that of the dendritic regions (7.1 GPa). The high Cr contents with finer dendritic structures were the major mechanisms for the excellent combination of hardness and corrosion resistance. The precipitation and growth mechanisms of the interdendritic phases were elaborated. This work provides a valuable reference for laser hot-wire cladding to prepare Fe-based alloys with high hardness and excellent corrosion resistance.

Effect of Mo addition on microstructure and mechanical properties of Cu-12.5Ni-5Sn alloy

Cu-12.5Ni-5Sn-xMo (x=0, 0.5, 1.0, 1.5 wt%) alloys were prepared using Spark Plasma Sintering (SPS) technology. The effect of Mo addition on the microstructure and mechanical properties of Cu-12.5Ni-5Sn alloy was investigated. The results indicate that adding trace amounts of Mo significantly refines the grain structure of Cu-12.5Ni-5Sn alloy, attributed to the formation of Mo-rich phases. Mo addition also inhibited the growth of discontinuous precipitation (DP) after aging treatment, reducing the DP volume fraction from approximately 25 % to 6 %. This effect is attributed to the precipitation of micron-sized Mo-rich phases at grain boundaries, which inhibit DP nucleation and growth by occupying γ-phase nucleation sites and pinning grain boundaries, thus impeding grain boundary diffusion. In addition, the interlamellar spacing of the discontinuous precipitation increases and the growth rate of lamellae decreases with increasing Mo content. Furthermore, an optimized combination of hardness (310 HB) and yield strength (586 MPa) was achieved in the Cu-12.5Ni-5Sn-1.0Mo alloy after aging treatment.

Quantification of Deleterious Phase Precipitation in a Hyper Duplex Stainless Steel Aged at 700-950 °C Using Optimized Linear Sweep Voltammetry: Effect of KOH Concentration

Quantification of Deleterious Phase Precipitation in a Hyper Duplex Stainless Steel Aged at 700-950 °C Using Optimized Linear Sweep Voltammetry: Effect of KOH Concentration

Effects of extrusion temperature on the microstructure and mechanical properties of low-alloyed Mg-Bi-Ca-Mn alloy

A new rare earth-free low-alloyed Mg-0.5Bi-0.8Ca-0.8Mn (wt.%) alloy was prepared at three extrusion temperatures (225, 250 and 275 °C). The effects of low-temperature extrusion on the microstructure and mechanical properties of the alloy were studied. Experimental results show that the dynamic recrystallization (DRX) grains are significantly refined by low-temperature extrusion, and the dynamic recrystallization process is further delayed by the Mn precipitate phase, resulting in a bimodal structure composed of ultrafine DRXed grains and coarse undynamic recrystallized (unDRXed) regions. At an extrusion temperature of 225 °C, the grain size was significantly refined, with an average DRXed grain size of 0.84 μm and a tensile yield strength of 418 MPa. Compared with other extruded magnesium alloys, the ultra-fine DRXed grains, strong basal fiber texture, high Schmid Factors of pyramidal <c + a> slip in the unDRXed regions, and along with a certain amount of second phase (Mg2Ca) distributed along the grain boundaries and nano-Mn particles uniformly distributed in the matrix, are the main reasons for the strength enhancement of low-temperature extruded magnesium alloys. The orientation of the DRXed grains in the alloy after extrusion at 250 °C is more random, which improves ductility. In addition, when the extrusion temperature reaches 275 °C, the alloy shows a fully recrystallized structure and exhibits rare earth (RE)-texture, obtaining high ductility but decreasing strength. This study provides a new idea for the development of high-strength Mg-Bi-based magnesium alloys by adjusting the extrusion temperature and alloying elements. This new high-strength and low-alloyed Mg-Bi-based alloy will help to enrich the series of high-performance, rare-earth free, low-cost extruded Mg alloy with certain application prospects.

Effect of Trace Element B on the Microstructure and Mechanical Properties of 8Cr4Mo4V Bearing Steel

By means of salt‐bath austempering treatment, microstructure observation, X‐Ray diffraction analysis, microhardness measurement, and friction and wear performance tests for 8Cr4Mo4V steels with standard composition and with trace addition of 0.005% boron, the effect of boron on the phase composition and mechanical properties of the steel is studied. The results show that trace element boron greatly increases the content of needle‐like lower bainite in the quenched microstructure, promotes the dissolution of undissolved carbides, reduces the content of M/A island, but coarsens grains. After tempering, trace element B increases the amount of bainite generation, refines the lath martensite, and significantly promotes the precipitation of carbides, whose size is finer, and the distribution is more dispersed. In terms of mechanical properties, trace element B improves the hardness by promoting the precipitation of the second phase and refining the lath martensite, and the increase in the bainite content changes the wear mechanism and enhances the wear resistance.

Effect of P2O5 on the viscous flow and crystallisation behaviour of slag in the double slag converter steelmaking process

In the current study, the effect of P2O5 on the viscous flow and crystallisation behaviour of slag in the double slag converter steelmaking process was investigated in laboratory. The results indicated that with the increase of P2O5 content, the softening temperature, hemispherical temperature and flowing temperature of steelmaking slag showed a decreasing trend, however, the viscosity increased. The FactSage thermodynamic software was used to predict the types and contents of crystallisation phases in the crystallisation process of steelmaking slag. It showed that with the increase of P2O5 content, the precipitation content of Ca5P2SiO12 increased, while the precipitation content of melilite decreased. The composition and microstructure of crystallisation phases were analysed using X-ray diffraction and scanning electron microscopy. The phase composition did not change with the increase of P2O5 content, but the diffraction peak intensity of each crystallisation phase was different. Besides, the precipitation of phosphorus-enriched phase was enhanced with the increase of P2O5 content.

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

In practical applications, intermetallic compounds like Laves phase and metal carbides adversely affect the performance of nickel‐based superalloys. Using a high‐temperature confocal laser scanning microscope, the solidification process of as‐cast GH3625 alloy containing Mg at different cooling rates (−20, −35, and −50 °C min−1) is studied. Fitting curves of the volume fraction of the solid phase with solidification temperature before and after Mg treatment are obtained. Trends of solid phase transformation rates with solidification temperature are determined. Differential scanning calorimetry is employed to analyze and statistically evaluate the melting temperature range and enthalpy of each phase during the melting process. Experimental results demonstrate that Mg treatment significantly accelerates the alloy solidification at the cooling rates of −20 and −35 °C min−1, while reducing the area of residual liquid phase at the same solidification temperature, disrupting the Laves/NbC eutectic relationship, and regularizing NbC morphology, transitioning its distribution from aggregation to dispersion. After Mg treatment, the precipitation of the Laves phase is significantly reduced. As a result, the influence mechanism of Mg treatment on the phase transformation and microstructure of GH3625 is clarified based on homogeneous nucleation theory.