PEO Brush Research Articles

KT-Scale Interactions and Stability of Colloids with Adsorbed Zwitterionic and Ethylene Oxide Copolymers

We report synthesis of novel zwitterionic triblock copolymers and direct measurements of their interactions when adsorbed to colloids and surfaces. We investigate triblock copolymers with poly(2-methacryloyloxyethylphosphorylcholine) (PMPC) end blocks separated by a poly(propylene oxide) (PPO) center block, with comparison to poly(ethylene oxide) PEO–PPO–PEO analogues. Interaction potentials are measured for a molecular weight series of PMPC and PEO copolymers adsorbed to hydrophobic colloids of varying diameter and planar surfaces. Findings indicate that, for the same number of repeat units, PMPC brushes generate repulsion at several times the distance of PEO brushes. PEO brush dimensions and interactions show good agreement with polymer brush models, whereas PMPC interactions suggest layer architectures with chain extensions approaching the PMPC block contour length. While PEO blocks must have 2–3 times as many repeat units to generate the same thickness as PMPC blocks, PMPC and PEO layers of the same t...

Structural Diversity and Phase Behavior of Brush Block Copolymer Nanocomposites

Brush block copolymers (BBCPs) exhibit attractive features for use as templates for functional hybrid nanomaterials including rapid ordering dynamics and access to broad ranges of domain sizes; however, there are relatively few studies of the morphology of the BBCPs as a function of their structural variables and fewer still studies of BBCP composite systems. Here we report the structural diversity and phase behavior of one class of BBCP nanocomposites as a function of the volume fractions of their components and the side chain symmetry of the BBCPs. We conducted a systematic investigation of gold nanoparticle (NP) (∼2 nm) assembly in a series of poly(tert-butyl acrylate)-block-poly(ethylene oxide) (PtBA-b-PEO) BBCPs with a fixed side chain length of PtBA (Mn = 8.2 kg/mol) but with different PEO brush lengths (Mn = 5.0, 2.0, or 0.75 kg/mol) as well as volume fractions (fPEO = 0.200–0.484). The gold NPs are selectively incorporated within the PEO domain via hydrogen bond interactions between the 4-mercapto...

Switching the Interpenetration of Confined Asymmetric Polymer Brushes

The interpenetration of two polymer brushes on approaching flat surfaces has been investigated. When compacting polymer brushes with an asymmetric charge on each surface, one neutral and the other weakly charged, we find that the brush interpenetration becomes a parameter that can be controlled by the pH of the hydrating solution. The switching between high and low degrees of brush interpenetration was investigated with numerical self-consistent field theory (nSCF) and experimentally using a sample environment which combines neutron reflectometry with a surface force type apparatus. Initially, a pair of uncharged poly(ethylene oxide), PEO, brushes are examined, where one of the brushes is deuterated to distinguish it from a hydrogenous counterpart. We find in both nSCF and these experiments that there is no significant overlap between the brushes as both compact into polymer blocks with little hydration. However, when a weak polyelectrolyte poly(2-(dimethylamino)ethyl methacrylate), PDMAEMA, brush is confined against a deuterated neutral PEO brush and the pH of the hydrating solution is below the polycation’s pKa of 7.5, then the presence of charged groups on the PDMAEMA allows significant interpenetration to occur between the two polymer brushes on contact. This interpenetration remains once the polymer brushes dehydrate due to the confining pressure that is applied. Raising the pH to a value above the pKa, removes the charges from the polyelectrolyte brush resulting in little to no interpenetration between the two brushes. Therefore, by simply adjusting the pH of the hydrating solution the interpenetration state between polymer brush pairs can be switched when one brush is a weak polyelectrolyte. Since polymer brushes are widely investigated and used to reduce friction between solid surfaces, this effect may have significant implications in the design and operation of polymer brushes with controllable friction properties.

Late stage drainage of block copolymer stabilized emulsion drops.

Polymer covered emulsion droplets have a considerable number of applications ranging from active cosmetics to advance drug delivery systems. In many of these systems the emulsion droplets do not exist in isolation but interact with other drops, surfaces and particles. In a step towards understanding how these complex mechanical interactions take place, we examine the interaction between a block copolymer covered emulsion droplet (polystyrene-b-poly(ethylene oxide) (PS-PEO) covered toluene) and a flat mica interface. As buoyancy pushes the droplet upwards, it buckles in as it nears the mica and traps a droplet of the surrounding fluid. The trapped outer fluid (water/glycerine in our experiment) drains out through an annular region of PEO brush. This study focuses on the late stage drainage, unique to large molecule surfactants, and examines the effects of the polymer and droplet size on the drainage rate. We introduce a scaling model of the drainage which highlights the importance of three lengthscales in the problem - the brush height, the slip length along the emulsion drop interface and the width of the annular contact region.

Amphiphilic brush polymers produced using the RAFT polymerisation method stabilise and reduce the cell cytotoxicity of lipid lyotropic liquid crystalline nanoparticles.

Self-assembled lipid lyotropic liquid crystalline nanoparticles such as hexosomes and cubosomes contain internal anisotropic and isotropic nanostructures, respectively. Despite the remarkable potential of such nanoparticles in various biomedical applications, the stabilisers used in formulating the nanoparticles are often limited to commercially available polymers such as the Pluronic block copolymers. This study explored the potential of using Reversible Addition-Fragmentation chain Transfer (RAFT) technology to design amphiphilic brush-type polymers for the purpose of stabilising phytantriol and monoolein-based lipid dispersions. The synthesised brush-type polymers consisted of a hydrophobic C12 short chain and a hydrophilic poly(ethylene glycol)methyl ether acrylate (PEGA) long chain with multiple 9-unit poly(ethylene oxide) (PEO) brushes with various molecular weights. It was observed that increasing the PEO brush density and thus the length of the hydrophilic component improved the stabilisation effectiveness for phytantriol and monoolein-based cubosomes. Synchrotron small-angle X-ray scattering (SAXS) experiments confirmed that the RAFT polymer-stabilised cubosomes had an internal double-diamond cubic phase with tunable water channel sizes. These properties were dependent on the molecular weight of the polymers, which were considered in some cases to be anisotropically distributed within the cubosomes. The in vitro toxicity of the cubosomes was assessed by cell viability of two human adenocarcinoma cell lines and haemolytic activities to mouse erythrocytes. The results showed that phytantriol cubosomes stabilised by the RAFT polymers were less toxic compared to their Pluronic F127-stabilised analogues. This study provides valuable insight into designing non-linear amphiphilic polymers for the effective stabilisation and cellular toxicity improvement of self-assembled lipid lyotropic liquid crystalline nanoparticles.

Molecular arrangement of symmetric and non-symmetric triblock copolymers of poly(ethylene oxide) and poly(isobutylene) at the air/water interface

The behavior of a series of amphiphilic triblock copolymers of poly(ethylene oxide) (PEO) and poly(isobutylene) (PIB); including both symmetric (same degree of polymerization (DP) of the terminal PEO blocks) PEOm-b-PIBn-b-PEOm and non-symmetric (different DP of the terminal PEO blocks) PEOm-b-PIBn-b-PEOz, is investigated at the air/water interface by measuring surface pressure vs mean molecular area isotherms (π vs mmA), Langmuir–Blodgett (LB) technique, and infrared reflection–absorption spectroscopy (IRRAS). The block copolymer (PEO32-b-PIB160-b-PEO32) with longer PEO segments forms a stable monolayer and the isotherm reveals a pseudo-plateau starting at π∼5.7mN/m, also observed in the IRRAS, which is assigned to the pancake-to-brush transition related to the PEO dissolution into the subphase and subsequent PEO brush dehydration. Another plateau is observed at π∼40mN/m, which is attributed to the film collapse due to multilayer formation. The pancake-to-brush transition could not be observed for samples with smaller PEO chains. The isotherms for block copolymers, with short PEO chains, both symmetric (PEO3-b-PIBn-b-PEO3) and non-symmetric (PEO12-b-PIBn-b-PEO3), reveal another transition at π∼20–25mN/m. This is interpreted to be due to the conformational transition from a folded state where the middle PIB block is anchored to the water surface at both ends by the terminal hydrophilic segments to an unfolded state with PIB anchored to the water surface at one end. It is assumed that this transition involves the removal of PEO3 chains from the water surface in case of non-symmetric PEO12-b-PIB85-b-PEO3 and in case of symmetric, probably one PEO3 of each PEO3-b-PIB85-b-PEO3 chain. Because of the weaker interaction of the short PEO3 chains with the water surface as compared with the relatively longer PEO12 chains, the film of PEO3-b-PIB85-b-PEO3 collapses at much lower surface pressure after the transition as compared with the PEO12-b-PIB85-b-PEO3. The AFM images reveal the formation of microdomains of almost uniform height (6–7nm) in LB films of PEO3-b-PIB85-b-PEO3 and PEO12-b-PIB85-b-PEO3 after transferring onto silicon surfaces. These domains are assumed to be the mesomorphic domains of ordered and folded PIB chains.

Adsorption, structural alteration and elution of peptides at pendant PEO layers

An experimentally based, quantitative understanding of the entrapment and function of small peptides within PEO brush layers does not currently exist. Earlier work provided a rationale for expecting that an ordered, compact peptide will enter the PEO phase more readily than a peptide of similar size that adopts a less ordered, less compact form, and that amphiphilicity will promote peptide retention within the hydrophobic region of the PEO brush. Here we more deliberately describe criteria for peptide integration and structural change within the PEO brush, and discuss the reversibility of peptide entrapment with changing solvent conditions. For this purpose, circular dichroism (CD) was used to record the adsorption and conformational changes of (amphiphilic) WLBU2 and (non-amphiphilic) polyarginine peptides at uncoated (hydrophobic) and PEO-coated silica nanoparticles. Peptide conformation was controlled between disordered and α-helical forms by varying the concentration of perchlorate ion. We show an initially more ordered (α-helical) structure promotes peptide adsorption into the PEO layer. Further, a partially helical peptide undergoes an increase in helicity after entry, likely due to concomitant loss of capacity for peptide-solvent hydrogen bonding. Peptide interaction with the PEO chains resulted in entrapment and conformational change that was irreversible to elution with changing solution conditions in the case of the amphiphilic peptide. In contrast, the adsorption and conformational change of the non-amphiphilic peptide was reversible. These results indicate that responsive drug delivery systems based on peptide-loaded PEO layers can be controlled by modulation of solution conditions and peptide amphiphilicity.

“Click & Seed” Approach to the Biomimetic Modification of Material Surfaces

A simple, versatile, protein-repulsive, substrate-independent biomimetic surface modification is presented that is based on the creation of a PEO brush on a polydopamine anchoring layer and its capacity for selective follow-up modifications with various ligands using a copper-catalyzed alkyne-azide cycloaddition reaction. The desired surface concentration of peptide biomimetic ligands can be controlled by adjusting the peptide concentration in the reaction mixture, then measuring the activity of (125)I-radiolabeled peptides that are immobilized on the substrates. The performance of the prepared substrates is tested in cell cultures with MEF cells and a human ECC line.

A Facile Method to Form a Densely Grafted PEO‐b‐P4VP Brush on Gold Surface

AbstractHere we report a facile method for the preparation of a PEO113‐b‐P4VP93 brush on gold surface with a grafting density as high as 1.32 chains/nm2; the P4VP blocks were physically adsorbed on gold surface forming an inner layer while the PEO blocks stretched towards the solution forming PEO brush. PEO113‐b‐P4VP93 micelles with P4VP core and PEO shell formed in methanol/water mixed solvents were used as the precursor. By adsorbing PEO113‐b‐P4VP93 micelles from pure water, in which the density of the micelles is the largest, maximum amount of the micelles was adsorbed onto gold surface, and the adsorbed micelles existed as individual domains on the surface. To prepare the polymer brush with a density as high as possible, we annealed the adsorbed micelles by methanol/water mixed solvent at the volume fraction of methanol (VF) of 20%, which was the proper proportion at which the core‐forming P4VP chains began to be flexible but the integrity of the micelles was remained. At this volume fraction, almost all the adsorbed micelles originally existing as individual domains were transformed into a dense polymer brush.

Water Is a Poor Solvent for Densely Grafted Poly(ethylene oxide) Chains: A Conclusion Drawn from a Self-Consistent Field Theory-Based Analysis of Neutron Reflectivity and Surface Pressure–Area Isotherm Data

By use of a combined experimental and theoretical approach, a model poly(ethylene oxide) (PEO) brush system, prepared by spreading a poly(ethylene oxide)-poly(n-butyl acrylate) (PEO-PnBA) amphiphilic diblock copolymer onto an air-water interface, was investigated. The polymer segment density profiles of the PEO brush in the direction normal to the air-water interface under various grafting density conditions were determined by using the neutron reflectivity (NR) measurement technique. To achieve a theoretically sound analysis of the reflectivity data, we used a data analysis method that utilizes the self-consistent field (SCF) theoretical modeling as a tool for predicting expected reflectivity results for comparison with the experimental data. Using this data analysis technique, we discovered that the effective Flory-Huggins interaction parameter of the PEO brush chains is significantly greater than that corresponding to the θ condition in Flory-Huggins solutions (i.e., χ(PEO-water)(brush chains)/χ(PEO-water)(θ condition) ≈ 1.2), suggesting that contrary to what is more commonly observed for PEO in normal situations (χ(PEO-water)(free chains)/χ(PEO-water)(θ condition) ≈ 0.92), the PEO chains are actually not "hydrophilic" when they exist as polymer brush chains, because of the many body interactions that are forced to be effective in the brush situation. This result is further supported by the fact that the surface pressures of the PEO brush calculated on the basis of the measured χ(PEO-water) value are in close agreement with the experimental surface pressure-area isotherm data. The SCF theoretical analysis of the surface pressure behavior of the PEO brush also suggests that even though the grafted PEO chains experience a poor solvent environment, the PEO brush layer exhibits positive surface pressures, because the hydrophobicity of the PEO brush chains (which favors compression) is insufficient to overcome the opposing effect of the chain conformational entropy (which resists compression).

Reduced Water Density in a Poly(ethylene oxide) Brush.

A model poly(ethylene oxide) (PEO) brush system, prepared by spreading a poly(ethylene oxide)-poly(n-butyl acrylate) (PEO-PnBA) amphiphilic diblock copolymer onto an air-water interface, was investigated under various grafting density conditions by using the X-ray reflectivity (XR) technique. The overall electron density profiles of the PEO-PnBA monolayer in the direction normal to the air-water interface were determined from the XR data. From this analysis, it was found that inside of the PEO brush, the water density is significantly lower than that of bulk water, in particular, in the region close to the PnBA-water interface. Separate XR measurements with a PnBA homopolymer monolayer confirm that the reduced water density within the PEO-PnBA monolayer is not due to unfavorable contacts between the PnBA surface and water. The above result, therefore, lends support to the notion that PEO chains provide a hydrophobic environment for the surrounding water molecules when they exist as polymer brush chains.

Control of the PEO Chain Conformation on Nanoparticles by Adsorption of PEO-block-Poly(l-lysine) Copolymers and Its Significance on Colloidal Stability and Protein Repellency

The physical adsorption of PEO(n)-b-PLL(m) copolymers onto silica nanoparticles and the related properties of poly(ethylene oxide) (PEO)-coated particles were studied as a function of the block copolymer composition. Copolymers adopt an anchor-buoy conformation at the particle surface owing to a preferential affinity of poly(L-lysine) (PLL) blocks with the silica surface over PEO blocks when a large excess of copolymer is used. The interdistance between PEO chains at particle surface is highly dependent on the size of PLL segments; a dense brush of PEO is obtained for short PLL blocks (DP = 10), whereas PEO chains adopt a so-called interacting "mushroom" conformation for large PLL blocks (DP = 270). The size of the PEO blocks does not really influence the copolymer surface density, but it has a strong effect on the PEO layer thickness as expected. Salt and protein stability studies led to similar conclusions about the effectiveness of a PEO layer with a dense brush conformation to prevent colloidal aggregation and protein adsorption. Besides, a minimal PEO length is required to get full stabilization properties; as a matter of fact, both PEO(45)-b-PLL(10) and PEO(113)-b-PLL(10) give rise to a PEO brush conformation but only the latter copolymer efficiently stabilizes the particles in the presence of salt or proteins.

Fabrication of high performance polyethersulfone UF hollow fiber membranes using amphiphilic Pluronic block copolymers as pore-forming additives

The amphiphilic Pluronic triblock copolymers of poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) have received much attention recently as both the surface modifier and pore former in membrane fabrication. In this study, a systematical study has been carried out to investigate the effect of Pluronics with different molecular architectures and contents as a pore-forming additive on the fabrication of polyethersulfone (PES) ultrafiltration (UF) hollow fibers, and to identify the most preferential features of Pluronic for making high performance membranes. The as-spun hollow fibers were characterized in terms of cross-sectional membrane morphology, membrane surface chemistry, mechanical properties, pure water permeation (PWP), molecular weight cut-off (MWCO), and pore size distribution. It was observed that the PWP and MWCO of the as-spun hollow fibers are dependent on the structure of additives. Among all the membranes spun with 5 wt% additives, the hollow fibers spun using Pluronic F127 and F108 as the additives possess the highest PWP, the lowest MWCO, and the narrowest pore size distribution. It is possible that the PEO brush layer formed on the internal pore surface by Pluronic F127 and F108 might reduce the apparent pore size and hence improved the solute rejection of the resultant membranes. A comparison between Pluronic and poly(ethylene glycol) (PEG) as additives also confirmed the importance of the presence of PPO chain in Pluronic in the formation of high-performance membranes. When Pluronic F127 concentration was 10 wt%, the as-spun hollow fiber exhibited the highest PWP of 113.8 L/m 2 h bar and the lowest MWCO of 9 kDa.

Microbial Bioavailability of Covalently Bound Polymer Coatings on Model Engineered Nanomaterials

By controlling nanoparticle flocculation and deposition, polymer coatings strongly affect nanoparticle fate, transport, and subsequent biological impact in the environment. Biodegradation is a potential route to coating breakdown, but it is unknown whether surface-bound polymers are bioavailable. Here we demonstrate, for the first time, that polymer coatings covalently bound to nanomaterials are bioavailable. Model poly(ethylene oxide) (PEO) brush-coated nanoparticles (densely cross-linked bottle brush copolymers) with hydrophobic divinyl benzene cross-linked cores and hydrophilic PEO brush shells, having ~ 30 nm hydrodynamic radii, were synthesized to obtain a nanomaterial in which biodegradation was the only available coating breakdown mechanism. PEO-degrading enrichment cultures were supplied with either PEO homopolymer or PEO brush nanoparticles as the sole carbon source, and protein and CO₂ production were monitored as a measure of biological conversion. Protein production after 90 h corresponded to 14% and 8% of the total carbon available in the PEO homopolymer and PEO brush nanoparticle cultures, respectively, and CO₂ production corresponded to 37% and 3.8% of the carbon added to the respective system. These results indicate that the PEO in the brush is bioavailable. Brush biodegradation resulted in particle aggregation, pointing to the need to understand biologically mediated transformations of nanoparticle coatings in order to understand the fate and transport of nanoparticles in the environment.

Adsorption of Anionic Surfactants in a Nonionic Polymer Brush: Experiments, Comparison with Mean-Field Theory, and Implications for Brush−Particle Interaction

The adsorption of the anionic surfactants sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS) in poly(ethylene oxide) (PEO) brushes was studied using a fixed-angle optical flow-cell reflectometer. We show that, just as in solution, there is a critical association concentration (CAC) for the surfactants at which adsorption in the PEO brush starts. Above the critical micelle concentration (CMC) the adsorption is found to be completely reversible. At low brush density the adsorption per PEO monomer is equal to the adsorption of these surfactants in bulk solution. However, with increasing brush density, the number of adsorbed surfactant molecules per PEO monomer decreases rapidly. This decrease is explained in terms of excluded volume interactions plus electrostatic repulsion between the negatively charged surfactant micelles. Experimentally, a plateau value in the total adsorption is observed as a function of grafting density. The experimental results were compared to the results of an analytical self-consistent field (aSCF) model, and we found quantitative agreement. Additionally, the model predicts that the plateau value found is in fact a maximum. Both experiments and model calculations show that the adsorption scales directly with the polymerization degree of the polymers in the brush. They also show that an increase in the ionic strength leads to an increase in the adsorbed amount, which is explained as being due to a decrease in the electrostatic penalty for the adsorption of the SDS micelles. The adsorption of SDS micelles changes the interactions of the PEO brush with a silica particle. This is illustrated by atomic force microscopy (AFM) measurements of the pull-off force of a silica particle from a PEO brush: at high enough PEO densities, the addition of SDS leads to a very strong reduction in the force necessary to detach the colloidal silica particle from the PEO brush. We attribute this effect to the large amount of negative charge incorporated in the PEO brush due to SDS adsorption.

Nisin adsorption to hydrophobic surfaces coated with the PEO–PPO–PEO triblock surfactant Pluronic ® F108

The adsorption and elution of the antimicrobial peptide nisin at hydrophobic, silanized silica surfaces coated with the poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) surfactant Pluronic ® F108 were measured in situ, with ellipsometry. While such layers are known to inhibit protein adsorption, nisin was observed to adsorb in multilayer quantities, to an extent similar to its adsorption at uncoated, hydrophobic surfaces. The rates of nisin adsorption and elution were generally slower at F108-coated surfaces. And, the sequential adsorption of nisin, including two adsorption–elution cycles at each surface, showed greater differences in adsorption rates between the first and second adsorption cycles, when evaluated at identical mass density, for uncoated relative to F108-coated surfaces. These results indicate that nisin adsorption occurs via “entrapment” within the PEO brush layer at F108-coated surfaces, in this way slowing adsorption and spontaneous elution, and inhibiting post-adsorptive molecular rearrangements by reducing the lateral mobility of nisin. While F108-coated layers rejected adsorption of serum albumin, sequential adsorption experiments carried out with nisin and albumin showed a low level of albumin adsorption when nisin was present at the interface.

Anti-fouling ultrafiltration membranes containing polyacrylonitrile- graft-poly(ethylene oxide) comb copolymer additives

Membrane fouling is one of the most important challenges faced in membrane ultrafiltration (UF) operations. In this study, polyacrylonitrile- graft-poly(ethylene oxide) (PAN- g-PEO), an amphiphilic comb copolymer with a water-insoluble polyacrylonitrile (PAN) backbone and hydrophilic poly(ethylene oxide) (PEO) side chains, was used as an additive in the manufacture of novel PAN UF membranes. During casting, the PAN- g-PEO additive segregates to form a PEO brush layer on all membrane surfaces, including internal pores. Wettability, pure water permeability, and resistance to irreversible fouling increased when either the amount of PAN- g-PEO added to the membrane or the PEO content of the comb copolymer was increased. These trends were consistent with measured adhesion forces between the membranes and a carboxylated latex particle probe in an atomic force microscopy (AFM) analysis, and with the near-surface PEO coverage as determined by X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) revealed further effects of additive incorporation on membrane morphology. In 24-h dead-end filtration studies, blend membranes prepared with 20 wt% PAN- g-PEO (comb PEO content: 39 wt%) were found to resist irreversible fouling by 1000 ppm solutions of bovine serum albumin (BSA), sodium alginate, and humic acid, recovering the initial pure water flux completely by a pure water rinse, or a backwash in the case of humic acid. This exceptional anti-fouling performance holds promise for extending UF membrane lifetimes without need for aggressive cleaning procedures.

Protein antifouling mechanisms of PAN UF membranes incorporating PAN- g-PEO additive

The antifouling mechanism of a novel polyacrylonitrile (PAN) ultrafiltration (UF) membrane incorporating the amphiphilic comb copolymer additive, polyacrylonitrile- graft-polyethylene oxide (PAN- g-PEO), has been investigated using a laboratory-scale cross-flow test unit and atomic force microscopy (AFM). In fouling tests with a bovine serum albumin (BSA) solution, PAN UF membranes incorporating 20% PAN- g-PEO possessed excellent antifouling characteristics, whereas a commercial PAN UF membrane showed severe pore blocking that followed with surface cake formation. The PAN- g-PEO/PAN blend membranes also exhibited fouling reversibility and constant BSA retention, which indicate their ability to separate macromolecules without altering the molecular weight cut-off. An AFM analysis with a model carboxylated colloid-probe measured no adhesion force with the blend membrane, while the commercial PAN membrane exhibited strong adhesion to the probe, consistent with the fouling properties of the membranes. The antifouling character of the blend membrane is attributed to the surface segregation and local orientation of PAN- g-PEO molecules at the membrane surface and pore walls during membrane casting, creating a dense PEO brush layer that provides a steric barrier to protein adsorption.

Formation of Large PEE Domains in PEE212−PEO112 Diblock Copolymer Monolayers: Shift of the PEO-Desorption Transition

PEE212-PEO112 diblock copolymer monolayers are studied at the air/water interface. At large molecular areas, with X-ray reflectivity, PEE domains are observed, which are partly immersed into the water. The domain thickness increases on compression (28 to 40 A). With off-specular X-ray reflectivity, an average domain radius of 750 A is found, but there are also smaller domains. Due to these space constraints, most PEO blocks form a brush beneath the PEE domains. Only a few PEO blocks form a corona surrounding the domains and adsorb flatly onto the air/water interface. The PEO desorption transition is observed at the typical pressure of 9 mN/m, when the flatly adsorbed PEO is compressed at a domain fraction of 95%. It occurs at 6 A2/EO monomer, about half the value found for lipopolymers or diblock copolymers with NPEE approximately NPEO or NPEE < NPEO. Apparently, the thickness of the PEE domains is determined by the forces from the two interfaces, not by the PEO block, for which flat adsorption beneath the domain would be more favorable instead of formation of a PEO brush.

Interaction of Bovine Serum Albumin and Human Blood Plasma with PEO-Tethered Surfaces: Influence of PEO Chain Length, Grafting Density, and Temperature

Solid surfaces are modified by grafting poly(ethylene oxide), PEO, to influence their interaction with indwelling particles, in particular molecules of bovine serum albumin and human plasma proteins. As a rule, the grafted PEO layers suppress protein adsorption. The suppression is most effective when the PEO layer is in a molecular brush conformation having a reciprocal grafting density (area per grafted PEO chain) less than the dimensions of the protein molecules. Nevertheless, the protein molecules may penetrate the PEO brush to some extent. For a given grafting density, the penetration is facilitated by increasing thickness of the brush. Tenuous brushes of reciprocal grafting densities exceeding the protein molecular dimensions enhance protein adsorption. The results point to a weak attractive interaction between PEO and protein. The protein repellency of a densely PEO-brushed surface is ascribed to a high activation energy for the protein molecules to enter the brush. Varying the temperature between 22 and 38 degrees C does not significantly affect the range of grafting density over which the brush changes from protein-attractive to protein-repellent.