Peak Intensity Measurements Research Articles

Experimental determination of reference intensity ratio essential for accurate thickness measurement of HfO2 ultrathin films by XPS

When measuring the thickness of ultrathin overlayer films using X‐ray photoelectron spectroscopy (XPS), accurate values of the reference intensity ratio (R0) and the effective attenuation length (L) are essential. By definition, R0 is the peak intensity ratio for an overlayer and the substrate in “bulk” phases. Two issues need to be addressed in experimental determining R0 for ultrathin films: (i) How might a contamination layer on the sample used for measuring peak intensities impact R0? And (ii) do differences in the structure or chemistry of an ultrathin film make it inappropriate to determine R0 using bulk forms of the overlayer? In this study, we demonstrate the experimental determination of the R0 for an ultrathin HfO2 film on a Si(100) substrate with a 2 nm SiO2 layer. The values of R0 were determined using (i) the bulk materials of the HfO2 film and substrate and (ii) the ultrathin HfO2 films after different cleaning treatments. The results show that the R0 determined by the ultrathin films is higher than that determined by the bulk materials. Also, keeping the same level of carbonaceous contamination on the sample surface by cleaning as much as possible is essential for an accurate experimental determination of R0. In addition, the effective attenuation length was obtained using samples with known thicknesses measured by X‐ray reflectometry. The thicknesses and uncertainty budget of the ultrathin HfO2 films were then evaluated.

Screening of volatile organic compounds (VOCs) from liquid fungal cultures using ambient mass spectrometry

The potential of fungi for use as biotechnological factories in the production of a range of valuable metabolites, such as enzymes, terpenes, and volatile aroma compounds, is high. Unlike other microorganisms, fungi mostly secrete secondary metabolites into the culture medium, allowing for easy extraction and analysis. To date, the most commonly used technique in the analysis of volatile organic compounds (VOCs) is gas chromatography, which is time and labour consuming. We propose an alternative ambient screening method that provides rapid chemical information for characterising the VOCs of filamentous fungi in liquid culture using a commercially available ambient dielectric barrier discharge ionisation (DBDI) source connected to a quadrupole-Orbitrap mass spectrometer. The effects of method parameters on measured peak intensities of a series of 8 selected aroma standards were optimised with the best conditions being selected for sample analysis. The developed method was then deployed to the screening of VOCs from samples of 13 fungal strains in three different types of complex growth media showing clear differences in VOC profiles across the different media, enabling determination of best culturing conditions for each compound-strain combination. Our findings underline the applicability of ambient DBDI for the direct detection and comparison of aroma compounds produced by filamentous fungi in liquid culture.Graphical abstract

Pain-free default mode network connectivity contributes to tonic experimental pain intensity beyond the role of negative mood and other pain-related factors.

Alterations in the default mode network (DMN) connectivity across pain stages suggest a possible DMN involvement in the transition to persistent pain. This study examined whether pain-free DMN connectivity at lower alpha oscillations (8-10 Hz) accounts for a unique variation in experimental peak pain intensity beyond the contribution of factors known to influence pain intensity. Pain-free DMN connectivity was measured with electroencephalography prior to 1 h of capsaicin-evoked pain using a topical capsaicin patch on the right forearm. Pain intensity was assessed on a (0-10) numerical rating scale and the association between peak pain intensity and baseline measurements was examined using hierarchical multiple regression in 52 healthy volunteers (26 women). The baseline measurements consisted of catastrophizing (helplessness, rumination, magnification), vigilance, depression, negative and positive affect, sex, age, sleep, fatigue, thermal and mechanical pain thresholds and DMN connectivity (medial prefrontal cortex [mPFC]-posterior cingulate cortex [PCC], mPFC-right angular gyrus [rAG], mPFC-left Angular gyrus [lAG], rAG-mPFC and rAG-PCC). Pain-free DMN connectivity increased the explained variance in peak pain intensity beyond the contribution of other factors (ΔR2 = 0.10, p = 0.003), with the final model explaining 66% of the variation (R2 = 0.66, ANOVA: p < 0.001). In this model, negative affect (β = 0.51, p < 0.001), helplessness (β = 0.49, p = 0.007), pain-free mPFC-lAG connectivity (β = 0.36, p = 0.003) and depression (β = -0.39, p = 0.009) correlated significantly with peak pain intensity. Interestingly, negative affect and depression, albeit both being negative mood indices, showed opposing relationships with peak pain intensity. This work suggests that pain-free mPFC-lAG connectivity (at lower alpha) may contribute to individual variations in pain-related vulnerability. These findings could potentially lead the way for investigations in which DMN connectivity is used in identifying individuals more likely to develop chronic pain.

Quantitative proteomics I.: Concept, design, and planning of quantitative proteomics experiments.

Quantitative proteomics I.: Concept, design, and planning of quantitative proteomics experiments.

Ultrasonographic scores for ileal Crohn’s disease assessment: Better, worse or the same as contrast-enhanced ultrasound?

BackgroundIntestinal ultrasound (IUS) is an increasingly used non-invasive tool to evaluate Crohn’s disease (CD) activity. Recently, two IUS scores that evaluate inflammatory activity have emerged: the Simple Ultrasound Activity Score for CD (SUS-CD) and the International Bowel Ultrasound Segmental Activity Score (IBUS-SAS). We aimed to compare the accuracy of SUS-CD, IBUS-SAS and contrast-enhanced ultrasound (CEUS) in predicting inflammatory activity in the terminal ileum in ileocolonoscopy in CD patients.MethodsRetrospective study including all consecutive CD patients submitted to IUS with CEUS directed to the terminal ileum performed by a single operator between April 2016 and March 2020. Segmental SUS-CD and IBUS-SAS were calculated. A time-intensity curve of the contrast bowel wall enhancement was created with measurement of peak intensity using CEUS. The CD endoscopic activity in ileocolonoscopy was graded by Simple Endoscopic Score for CD (SES-CD) as inactive (SES-CD < 7) or active (SES-CD ≥ 7).ResultsFifty patients were included, 54.0% were female, with mean age of 34 ± 12 years, and most had isolated ileal disease (60.0%), and a nonstricturing, nonpenetrating behaviour (44.0%). Most of the patients (60.0%) had active endoscopic disease (SES-CD ≥ 7). SUS-CD and IBUS-SAS were not different between patients with active or inactive endoscopic disease (p = 0.15; 0.57, respectively), having a poor accuracy to correlate endoscopic activity (area under de curve (AUC) 0.62; 0.55, respectively). Peak intensity in CEUS was significantly different in patients with active or inactive endoscopic disease (p = 0.004), having a good accuracy to correlate endoscopic activity (AUC 0.80).ConclusionUnlike CEUS, SUS-CD and IBUS-SAS were not able to accurately correlate endoscopic activity in terminal ileum in CD. Therefore, CEUS is a non-invasive emerging method that should be increasingly integrated in the ultrasonographic evaluation of CD patients.

Interobserver reproducibility of contrast-enhanced ultrasound in diabetic nephropathy.

To investigate the interobserver reproducibility of contrast-enhanced ultrasound (CEUS) in patients with diabetic nephropathy. A total of 40 patients with diabetic nephropathy were enrolled in this retrospective study. We measured peak intensity (PEAK), time-to-peak (TP), area under the curve (AUC) and mean transit time (MTT) of renal CEUS in each patient. Each parameter was performed by two independent observers. The interobserver reproducibility was assessed using intraclass correlation coefficients (ICCs) with 95% confidence intervals (CIs) and Bland-Altman plots by mean difference with 95% limits of agreement (LOAs). The parameters of the left and right kidneys showed moderate or good reliability. The best was the left kidney AUC parameters (ICC,0.945),with a 95% CI of 0.896-0.971.The Bland-Altman plots showed that the mean differences between the right renal parameters (PEAK, TP, AUC and MTT) obtained between the observers 1 and 2 were -6.63%,2.54%,-11.30%,-2.22%, and the 95% LOAs are -30.78 to 17.52%, -30.15 to 35.23%, -43.95 to 21.35%, -44.50 to 40.06%. While the left ones were -2.89%, 0.32%, -8.26%, 1.25% , and the 95% LOAs were -38.50 to 32.72%, -31.98 to 32.62%, -57.89 to 41.37%, -37.21 to 39.71%, respectively. Quantitative CEUS can show good interobserver reproducibility, which is better for the right kidney. It seems necessary to establish standardized techniques for obtaining contrast-enhanced quantitative analysis of renal blood perfusion. Quantitative assessment of renal perfusion by CEUS in patients with diabetic nephropathy provides diagnostic information. Furthermore, renal perfusion assessment in patients with diabetic nephropathy using CEUS has good reproducibility.

A multi-sensor evaluation of precipitation uncertainty for landslide-triggering storm events.

Extreme precipitation can have profound consequences for communities, resulting in natural hazards such as rainfall‐triggered landslides that cause casualties and extensive property damage. A key challenge to understanding and predicting rainfall‐triggered landslides comes from observational uncertainties in the depth and intensity of precipitation preceding the event. Practitioners and researchers must select from a wide range of precipitation products, often with little guidance. Here we evaluate the degree of precipitation uncertainty across multiple precipitation products for a large set of landslide‐triggering storm events and investigate the impact of these uncertainties on predicted landslide probability using published intensity–duration thresholds. The average intensity, peak intensity, duration, and NOAA‐Atlas return periods are compared ahead of 177 reported landslides across the continental United States and Canada. Precipitation data are taken from four products that cover disparate measurement methods: near real‐time and post‐processed satellite (IMERG), radar (MRMS), and gauge‐based (NLDAS‐2). Landslide‐triggering precipitation was found to vary widely across precipitation products with the depth of individual storm events diverging by as much as 296 mm with an average range of 51 mm. Peak intensity measurements, which are typically influential in triggering landslides, were also highly variable with an average range of 7.8 mm/h and as much as 57 mm/h. The two products more reliant upon ground‐based observations (MRMS and NLDAS‐2) performed better at identifying landslides according to published intensity–duration storm thresholds, but all products exhibited hit ratios of greater than 0.56. A greater proportion of landslides were predicted when including only manually verified landslide locations. We recommend practitioners consider low‐latency products like MRMS for investigating landslides, given their near‐real time data availability and good performance in detecting landslides. Practitioners would be well‐served considering more than one product as a way to confirm intense storm signals and minimize the influence of noise and false alarms.

Measurements of the optical and thermal properties of the 2D black phosphorus coating

Black phosphorus is a 2D material, which properties are still being discovered. In this paper, the sensitivity to the temperature of a few-layer black phosphorus coating deposited, on the surface of a microsphere-based fiber-optic sensor, by a dip-coating method is presented. The coating was investigated after 2, 3, and 5 deposition cycles and during temperature growth from 50 °C to 300 °C in an interferometric setup. The intensity of the reflected signal increases with each applied layer. During the investigation of the thermal properties, in the range of 50 °C–200 °C, the polynomial growth rate of the reflected signal can be observed, whereas, for the temperatures over 200 °C, the measured peak intensity of the reflected signal stabilizes at a nearly constant level.

Direct Multielement Analysis of Polydisperse Microparticles by Classification-Single-Particle ICP-OES in the Field of Lithium-Ion Battery Electrode Materials

The chemical and structural complexity of lithium-ion battery electrodes and their constituting materials requires comprehensive characterization techniques to reveal degradation phenomena at the mesoscale. For the first time, application of single-particle inductively coupled plasma-optical emission spectroscopy enables the investigation of the chemomechanical interplay on the particle level of lithium transition-metal oxide [e.g., Li(Ni1/3Co1/3Mn1/3)O2] cathode materials. The sample-inherent polydisperse size distribution of particles ranging up to 10 μm was effectively restricted with the use of a custom-made gravitational-counter-flow classifier to facilitate complete particle vaporization and excitation. After classification, the particles were transported directly to the plasma by means of an argon flow to prevent chemical alterations in aqueous media due to potentially occurring Li+-H+ exchange reactions. The size-separated particles were monitored online by flow cell particle analysis (FPA). The influence of different gas flow settings and plasma parameters on the peak emission intensity of Li and Mn was evaluated. A particle size detection limit of ∼0.5 μm was estimated based on the 3σ criterion of the baselines and the measured peak intensities for Li and Mn considering the particle size distribution as obtained by FPA. The corresponding analyte masses at the detection limits were ∼30 and ∼180 fg for Li and Mn, respectively. Furthermore, an approach for a matrix-matched external calibration with electrochemically delithiated lithium transition-metal oxides is presented.

High-Sensitivity Glycan Profiling of Blood-Derived Immunoglobulin G, Plasma, and Extracellular Vesicle Isolates with Capillary Zone Electrophoresis-Mass Spectrometry

We developed a highly sensitive method for profiling of N-glycans released from proteins based on capillary zone electrophoresis coupled to electrospray ionization mass spectrometry (CZE-ESI-MS) and applied the technique to glycan analysis of plasma and blood-derived isolates. The combination of dopant-enriched nitrogen (DEN)-gas introduced into the nanoelectrospray microenvironment with optimized ionization, desolvation, and CZE-MS conditions improved the detection sensitivity up to ∼100-fold, as directly compared to the conventional mode of instrument operation through peak intensity measurements. Analyses without supplemental pressure increased the resolution ∼7-fold in the separation of closely related and isobaric glycans. The developed method was evaluated for qualitative and quantitative glycan profiling of three types of blood isolates: plasma, total serum immunoglobulin G (IgG), and total plasma extracellular vesicles (EVs). The comparative glycan analysis of IgG and EV isolates and total plasma was conducted for the first time and resulted in detection of >200, >400, and >500 N-glycans for injected sample amounts equivalent to <500 nL of blood. Structural CZE-MS2 analysis resulted in the identification of highly diverse glycans, assignment of α-2,6-linked sialic acids, and differentiation of positional isomers. Unmatched depth of N-glycan profiling was achieved compared to previously reported methods for the analysis of minute amounts of similar complexity blood isolates.

Non-destructive detection of machining-induced white layers through grain size and crystallographic texture-sensitive methods

Detection of machining-induced white layers is currently a destructive inspection process with a form of cross-sectional microscopy required. This paper, therefore, reports on the development of a novel non-destructive inspection method for detecting white layers using grain size-sensitive and crystallographic texture-sensitive techniques. It is shown that x-ray diffraction can be used to detect white layers as thin as 5 μm in Ti-6Al-4 V through measurement of diffraction peak breadths and diffraction peak intensities, due to the influence of the sub 100 nm grain size and high lattice strain in the white layer, as well as the strong crystallographic texture in this titanium alloy. Compared to the existing optical microscopy inspection method, which can take days due to the number of steps involved, the x-ray diffraction peak breadth method offers non-destructive white layer detection in a matter of minutes at a resolution of 5 μm or less that competes directly with the optical method. Spatially resolved acoustic spectroscopy, a laser-generated ultrasonic surface acoustic wave detection method, can also be used to identify anomalous surfaces, containing a white layer or swept grain material, due to its sensitivity to the crystallographic texture changes that arise in severely plastically deformed Ti-6Al-4V as in Titanium with 6 % Aluminium and 4% Vanadium.

Domain Mapping of Chondroitin/Dermatan Sulfate Glycosaminoglycans Enables Structural Characterization of Proteoglycans

Of all posttranslational modifications known, glycosaminoglycans (GAGs) remain one of the most challenging to study, and despite the recent years of advancement in MS technologies and bioinformatics, detailed knowledge about the complete structures of GAGs as part of proteoglycans (PGs) is limited. To address this issue, we have developed a protocol to study PG-derived GAGs. Chondroitin/dermatan sulfate conjugates from the rat insulinoma cell line, INS-1832/13, known to produce primarily the PG chromogranin-A, were enriched by anion-exchange chromatography after pronase digestion. Following benzonase and hyaluronidase digestions, included in the sample preparation due to the apparent interference from oligonucleotides and hyaluronic acid in the analysis, the GAGs were orthogonally depolymerized and analyzed using nano-flow reversed-phase LC-MS/MS in negative mode. To facilitate the data interpretation, we applied an automated LC-MS peak detection and intensity measurement via the Proteome Discoverer software. This approach effectively provided a detailed structural description of the nonreducing end, internal, and linkage region domains of the CS/DS of chromogranin-A. The copolymeric CS/DS GAGs constituted primarily consecutive glucuronic-acid-containing disaccharide units, or CS motifs, of which the N-acetylgalactosamine residues were 4-O-sulfated, interspersed by single iduronic-acid-containing disaccharide units. Our data suggest a certain heterogeneity of the GAGs due to the identification of not only CS/DS GAGs but also of GAGs entirely of CS character. The presented protocol allows for the detailed characterization of PG-derived GAGs, which may greatly increase the knowledge about GAG structures in general and eventually lead to better understanding of how GAG structures are related to biological functions.

An electrochemical investigation of oxygen adsorption on Pt single crystal electrodes in a non-aqueous Li+ electrolyte

Cyclic voltammetry has been used to probe the initial stages of oxygen reduction and oxidation in lithium-containing dimethyl sulfoxide at well-defined Pt single crystal electrodes in order to elucidate any catalytic effects ascribable to surface structure. In contrast to previous work involving sodium-oxygen, lithium-oxygen studies did not yield any significant differences for reaction on the three basal planes of platinum. Rather, all three planes generated a similar voltammetric response. However, by judicious use of various potential sweep limits, the formation of superoxide together with both a “conformal” or surface adlayer of lithium peroxide (Li2O2) together with a “microcrystallite” surface Li2O2 phase was resolved. Voltammetric peak intensity versus sweep rate measurements confirmed that superoxide electrooxidation was diffusion limited whereas electrooxidation of the two Li2O2 phases displayed behaviour typical of a surface-confined process. Under steady-state conditions for the formation of superoxide, it was found that for both the conformal and microcrystallite Li2O2 phases, electrooxidation followed zero-order kinetics, pointing to the importance of free surface sites in facilitating these reactions. A marked change in the rate of Li2O2 formation was found to coincide with a coverage of 0.25 monolayers, as measured by the charge density of the conformal Li2O2 electrooxidation peak. We postulate that electron tunnelling through both the conformal Li2O2 layer and microcrystallites deposited on this surface layer coincides with this coverage and accounts for such behaviour. This phenomenon of electron tunnelling through single conformal and mixed conformal/microcrystallite structures should prove vitally important in governing the overall electrooxidation rate.

The Multi-INstrument Burst ARchive (MINBAR)

Abstract We present the largest sample of type I (thermonuclear) X-ray bursts yet assembled, comprising 7083 bursts from 85 bursting sources. The sample is drawn from observations with Xenon-filled proportional counters on the long-duration satellites RXTE, BeppoSAX, and International Gamma-Ray Astrophysics Laboratory between 1996 February 8 and 2012 May 3. The burst sources were drawn from a comprehensive catalog of 115 burst sources, assembled from earlier catalogs and the literature. We carried out a consistent analysis for each burst light curve (normalized to the relative instrumental effective area) and provide measurements of rise time, peak intensity, burst timescale, and fluence. For bursts observed with the RXTE/PCA and BeppoSAX/Wide Field Camera we also provide time-resolved spectroscopy, including estimates of bolometric peak flux and fluence, and spectral parameters at the peak of the burst. For 950 bursts observed with the PCA from sources with previously detected burst oscillations, we include an analysis of the high time resolution data, providing information on the detectability and amplitude of the oscillations, as well as where in the burst they are found. We also present analysis of 118,848 observations of the burst sources within the sample time frame. We extracted 3–25 keV X-ray spectra from most observations, and (for observations meeting our signal-to-noise criterion) we provide measurements of the flux, spectral colors, and, for selected sources, the position on the color–color diagram, for the best-fit spectral model. We present a description of the sample, a summary of the science investigations completed to date, and suggestions for further studies.

Limitations of deuterium-labeled internal standards for quantitative electrospray ionization mass spectrometry analysis of fatty acid metabolites.

The electrospray ionization mass spectrometry (ESI-MS) methodology often shows poor ionization reproducibility in the analysis of biological samples. Therefore, normalization of the measured peak intensities is essential. It is believed that quantitative data with high reproducibility can be obtained by adding a constant amount of an internal standard (IS) material labeled with stable isotopes to each sample, thus allowing the correction of the quantitative value of the target compound by that of the IS. We investigated whether the presence or absence of a labeled IS improves the accuracy of these quantitative values. Triple quadrupole MS coupled with liquid chromatography was used to analyze fatty acid metabolites in biological samples as target compounds. Two independent systems were used to provide a measure of reproducibility in two different laboratories. Data having poor reproducibility in the raw peak areas were efficiently normalized using the IS, but, crucially, the IS method using stable isotopes was not always necessary. In some cases, the reproducibility was relatively good even without using the IS. In a contaminant matrix, the MS response behavior of the target compound and its stable isotope-labeled material was complicated. Since ion suppression by matrix contaminants was dependent on the concentration of the target compound, the added amounts of the ISs were also important, Furthermore, an equivalent normalization effect was obtained by using a pooled quality control sample as an external standard, thus obviating the need for labeled IS samples, which are often expensive and sometimes not commercially available. Our results raise the question as to whether the quantitative method using stable-isotope-labeled ISs is always necessary and beneficial. However, the results obtained in this study cannot be generalized because only fatty acid metabolites were examined using ESI-MS and only a highly substituted deuterium-labeled IS was used.

Extremely large-angle beam deflection based on low-index sparse dielectric metagratings

Metasurfaces for beam engineering are usually implemented by using dense-plasmonic or high-contrast dielectric building blocks with deep-subwavelength feature size and strong field confinement. Here, we theoretically and experimentally demonstrate extremely large angle deflection with a very steep phase gradient based on low-contrast () metagratings composed of very sparse building blocks. Only two ridges are included in a 4π variation supercell, which diffracts the normal excitation to desired angles as large as 80° with a theoretical efficiency of more than 80%. Due to the limited beam radius relative to the metasurfaces, the angular distribution of the intensity is broadened with reduced peak intensity. Such metagratings are 3D-printed for 0.14 THz operation. The measured peak intensities are 57% of the theoretical ones due to material loss and fabrication errors. Repeatability, bandwidth and angular sensitivity are systematically studied, and the results pave the way towards using practical THz elements for large-gradient wavefront shaping.

Assessment of neovascularization during bone healing using contrast-enhanced ultrasonography in a canine tibial osteotomy model: a preliminary study.

Blood perfusion of skeletal muscle and callus was evaluated using contrast-enhanced ultrasonography (CEUS) in a canine osteotomy model to determine the applicability of CEUS in the assessment of neovascularization during fracture healing and to compare the vascular signals on CEUS between external skeletal fixation and cast-applied dogs. In 6 Beagle dogs, a simple transverse osteotomy was performed at the left tibial shaft and external skeletal fixation (n = 3) or a cast (n = 3) was applied. Radiography, power Doppler ultrasonography (power Doppler), and CEUS were performed until complete union was achieved. On CEUS, vascular changes were quantitatively evaluated by measuring peak intensity (PI) and time to PI in the soft tissue and callus and by counting the vascular signals. Vascular signals from the soft tissue were detected on power Doppler and CEUS on day 2. Significantly more vascular signals were detected by CEUS than by power Doppler. On CEUS, PI in the surrounding soft tissue was markedly increased after the fracture line appeared indistinctively changed on radiography in all dogs. In the cast-applied dogs, vascular signals from the periosteal and endosteal callus were detected on CEUS before mineralized callus was observed on radiography. CEUS was useful in assessing the vascularity of soft tissue and callus, particularly in indirect fracture healing, and provided indications of a normally healing fracture.

Arbuscular mycorrhizal fungi effect growth and photosynthesis of Phragmites australis (Cav.) Trin ex. Steudel under copper stress.

Arbuscular mycorrhizal fungi (AMF) is an effective way to remove heavy metals' inhibition on plants, however, few relevant research attempts have been made to determine the contribution of AMF to the physiological and biochemical changes related to the enhanced copper tolerance of Phragmites australis under metal-stressed conditions. In this study, the effects of AMF inoculation on P. australis under different concentrations of copper stress were investigated according to the changes in the parameters related to growth and development, and photosynthetic charateristics. Then, differentially expressed proteins (DEPs) were evaluated by the Isobaric Tag for Relative and Absolute Quantification (iTRAQ) system, which could accurately quantify the DEPs by measuring peak intensities of reporter ions in tandem mass spectrometry (MS/MS) spectra. It was found that AMF inoculation may relieve the photosynthesis inhibition caused by copper stress on P. australis and thus promote growth. Proteomic analysis results showed that under copper stress, the inoculation of R. irregularis resulted in a total of 459 differently-expressed proteins (200 up-regulated and 259 down-regulated) in root buds. In addition, the photosynthetic changes caused by AMF inoculation mainly involve the up-regulated expression of transmembrane protein-pigment complexes CP43 (photosystem II) and FNR (ferredoxin-NADP+ oxidoreductase related to photosynthetic electron transport). These results indicate that AMF could effectively improve the growth and physiological activity of P. australis under copper stress, and thus provides a new direction and instructive evidence for determining the mechanisms by which AMF inoculation enhances the copper tolerance of plants.

Achieving the laser intensity of 5.5×1022 W/cm2 with a wavefront-corrected multi-PW laser.

The generation of ultrahigh intensity laser pulses was investigated by tightly focusing a wavefront-corrected multi-petawatt Ti:sapphire laser. For the wavefront correction of the PW laser, two stages of deformable mirrors were employed. The multi-PW laser beam was tightly focused by an f/1.6 off-axis parabolic mirror and the focal spot profile was measured. After the wavefront correction, the Strehl ratio was about 0.4, and the spot size in full width at half maximum was 1.5×1.8 μm2, close to the diffraction-limited value. The measured peak intensity was 5.5×1022 W/cm2, achieving the highest laser intensity ever reached.

Time-resolved X-ray diffraction study of the structural dynamics in an epitaxial ferroelectric thin Pb(Zr0.2Ti0.8)O3 film induced by sub-coercive fields

The electric field-dependence of structural dynamics in a tetragonal ferroelectric lead zirconate titanate thin film is investigated under subcoercive and above-coercive fields using time-resolved X-ray diffraction. The domain nucleation and growth are monitored in real time during the application of an external field to the prepoled thin film capacitor. We propose the observed broadening of the in-plane peak width of the symmetric 002 Bragg reflection as an indicator of the domain disorder and discuss the processes that change the measured peak intensity. Subcoercive field switching results in remnant disordered domain configurations.