Iron Oxide Research Articles

Groundnut shell carbon quantum dot magnetic iron oxide nanocomposite (GSCQD-FeFe2O4) for lead removal from water

Groundnut shell carbon quantum dot magnetic iron oxide nanocomposite (GSCQD-FeFe2O4) for lead removal from water

Impact of nano Fe2O3 on radiation parameters of epoxy reinforced with nano carbon

This study aims to investigate the effectiveness of iron oxide (Fe2O3) and carbon black in micro and nanoscales incorporated into an epoxy adhesive matrix for gamma-ray attenuation. The composites were prepared via a simple and cost-effective synthesis method. The grain size of powder NPs was measured using a transmission electron microscope (TEM), and the particle size was about 20 ± 5 nm and 31.46 ± 2 nm for carbon and Fe2O3, respectively. The morphological properties were characterized by a scanning electron microscope, which indicated the excellent dispersion of NPs, which blocked almost all pores of the composite and increased the capability of radiation attenuation. In addition, the chemical composition of samples using energy dispersive X-rays (EDX) and the compressive strength were measured. Furthermore, the linear and mass attenuation coefficients were determined experimentally for incident photon energies of 59.51–1408.01 keV emitted from γ-ray sources using the sodium iodide scintillation detector NaI. A comparison was conducted between the experimental data and theoretical results that obtained from XCOM software, examined the validity of the experimental results. The relation deviation rate was found to vary between 0.0008 and 2.83%. Furthermore, the measurement of the relation deviation rate between the linear attenuation coefficients of micro and nano composites revealed a range of values between 1 and 25%. Also, shielding parameters such as half-value layer (HVL), tenth-value layer (TVL), mean free path (MFP), and effective atomic number (Zeff) were measured. Moreover, the equivalent atomic number (Zeq), absorption, and exposure buildup factors for prepared samples were calculated. The results showed that the incorporation of Fe2O3 NPs enhanced the shielding capability of the composites, as evidenced by the significant reduction in gamma-ray transmission. The composite materials exhibited excellent mechanical strength, making them suitable for practical applications in radiation shielding. Furthermore, it was determined that the elevation in N-Fe2O3 concentration resulted in a direct increase in the linear attenuation coefficient, from 0.314 to 0.519 cm−1 at 0.5951 MeV and from 0.099 to 0.124 cm−1 at 0.662 MeV. Nevertheless, a slight increase was discerned in the identified mass attenuation coefficients at 0.1332 and 0.1408 MeV. The experimental data for MFP, HVL, and TVL demonstrate that the EFeC4 sample exhibits optimal performance, with values of 1.9, 1.3, and 4.4 cm at 0.5951 MeV, and at 0.661 MeV, the values are 8.04, 5.57, and 18.52 cm, while at 0.1408 MeV, the values are 12.06, 8.36, and 27.78 cm, respectively. Overall, this research highlights the potential of iron oxide-carbon/epoxy composites as efficient and reliable materials for gamma-ray protection in various fields, including nuclear power plants, medical facilities, and space exploration.

Characterization and applications of iron oxide nanoparticles synthesized from Phyllanthus emblica fruit extract

Nanotechnology is a treasure trove of diversified themes which are endowed with broad applications. Herein, iron oxide (Fe2O3) nanoparticles were synthesized using Phyllanthus emblica aqueous fruit extract. The UV-Visible spectrum exhibited a surface plasmon resonance peak at 295nm. Fourier Transform Infrared Spectroscopy provided insight into the functional groups responsible for capping. X-ray diffraction analysis authenticated the crystalline nature of nanoparticles, while energy dispersive X-ray spectroscopy divulged that iron and oxygen comprised 54% of the nanoparticles’ weight. Scanning electron microscopy established irregular morphology and agglomeration of nanoparticles. The Fe2O3 nanoparticles validated potent antimicrobial activity against 11 bacterial and 1 fungal isolates. The biggest zone of inhibition (23mm) was measured against S. enterica, whereas the smallest zone of inhibition (12mm) was documented against C. albicans and E. coli. The values for minimum inhibitory concentration ranged between 10 and 15μg/ml for all microbes. Nevertheless, no synergy was exhibited by the nanoparticles with any of the selected antibiotics (Fractional Inhibitory Concentration Index > 1). The photocatalytic dye degradation capability of Fe2O3 nanoparticles was assessed and the observations implied a significant increase in degradation of methyl red although, not of methylene blue. Furthermore, the nanoparticles were in possession of substantial antioxidant (34–38%) and anti-inflammatory (31–38%) capacities. Consequent upon the robust activities of P. emblica-mediated nanoparticles, these can be scrutinized for biomedical and environmental implementations in future.

Stabilization of arsenic-cadmium co-contaminated soil with the iron-manganese sludge derived amendment: Effects and mechanisms

An iron-manganese sludge-derived amendment was proposed to remediate arsenic (As) and cadmium (Cd) co-contaminated soil, with a strong adsorptive capacity across pH 4 to 10. The Langmuir model defined maximum adsorption at 78.17 mg/g for As(III), 110.48 mg/kg for As(V), and 65.77 mg/g for Cd(II). The X-ray photoelectron spectroscopy (XPS) spectra provided insights into the chemical interactions: As was predominantly complexed or ligand exchanged with iron(hydr)oxides. In contrast, cadmium exhibited a tendency to bond with acylamino and carboxyl groups, in addition to the ferric hydroxyl groups. Notably, 42.15% of the adsorbed As(III) was oxidized into As(V) by Mn(IV) oxides present in the amendment. The soil-verification experiment demonstrated that an amendment dosage of 40 g/kg was efficacious in reducing the leaching concentration of As and Cd to maintained below the safety thresholds of 0.1 mg/L and 0.01 mg/L, respectively, for pH levels 4 to 11, meeting the Chinese Surface Water Quality Standard V (GB3838-2002). After the stabilization, the exchangeable fractions of As and the acid-soluble fractions of Cd were significantly reduced, with these elements being transformed into more stable forms. The amendment maintained the soil's neutral pH and adjusted the soil physicochemical properties. This article presents a holistic approach by examining the organic-inorganic composite of iron-manganese oxides with polyacrylamide, modified as a stabilizing amendment for As and Cd co-contaminated soil. This innovative amendment adeptly navigates the previously conflicting stabilization mechanisms for anionic and cationic metals. Offering dual advantages, the amendment not only remediates soil but also addresses the disposal of waste, presenting a win-win solution for environmental management.

Enhanced functionalization of superparamagnetic Fe3O4 nanoparticles for advanced drug enrichment and separation applications

Backgroundsuperparamagnetic ferroferric oxide (Fe3O4) nanoparticles can be extensively functionalized for applications in drug enrichment and separation. Their high magnetic responsiveness and controllable surface modification enable rapid drug enrichment and separation under external magnetic fields. This study aimed to enhance the application potential of superparamagnetic Fe3O4 nanoparticles in the field of drug enrichment and separation by functionalizing these nanoparticles to improve their biocompatibility and targeting capabilities.Methodssuperparamagnetic Fe3O4 nanoparticles functionalized with dopamine were synthesized using benzyl alcohol as the solvent and iron acetylacetonate as the precursor. The dopamine-functionalized superparamagnetic iron oxide nanoparticles were used to analyze protein enrichment and separation. Characterization of the nanoparticles was conducted, including analysis of particle size distribution, Zeta potential, and fluorescence spectra using a fluorescence spectrophotometer.Resultsthe Fe3O4 nanoparticles maintained high magnetism from the original material and exhibited uniform particle size distribution and stable Zeta potential. The saturation magnetization of dopamine-functionalized superparamagnetic Fe3O4 nanoparticles showed no significant difference compared to before coating, indicating minimal influence of dopamine on the internal magnetic core of the nanoparticles. The Fe3O4 nanoparticles demonstrated good biocompatibility and stability.Conclusionfunctionalization of superparamagnetic Fe3O4 nanoparticles significantly enhances their efficiency in drug enrichment and separation processes, suggesting broad applications in the pharmaceutical industry.

Magnetic Hyperthermia in Glioblastoma Multiforme Treatment

Glioblastoma multiforme (GBM) represents one of the most critical oncological diseases in neurological practice, being considered highly aggressive with a dismal prognosis. At a worldwide level, new therapeutic methods are continuously being researched. Magnetic hyperthermia (MHT) has been investigated for more than 30 years as a solution used as a single therapy or combined with others for glioma tumor assessment in preclinical and clinical studies. It is based on magnetic nanoparticles (MNPs) that are injected into the tumor, and, under the effect of an external alternating magnetic field, they produce heat with temperatures higher than 42 °C, which determines cancer cell death. It is well known that iron oxide nanoparticles have received FDA approval for anemia treatment and to be used as contrast substances in the medical imagining domain. Today, energetic, efficient MNPs are developed that are especially dedicated to MHT treatments. In this review, the subject’s importance will be emphasized by specifying the number of patients with cancer worldwide, presenting the main features of GBM, and detailing the physical theory accompanying the MHT treatment. Then, synthesis routes for thermally efficient MNP manufacturing, strategies adopted in practice for increasing MHT heat performance, and significant in vitro and in vivo studies are presented. This review paper also includes combined cancer therapies, the main reasons for using these approaches with MHT, and important clinical studies on human subjects found in the literature. This review ends by describing the most critical challenges associated with MHT and future perspectives. It is concluded that MHT can be successfully and regularly applied as a treatment for GBM if specific improvements are made.

Charge Transfer in n-FeO and p-α-Fe2O3 Nanoparticles for Efficient Hydrogen and Oxygen Evolution Reaction

This study aims to explore the n-FeO and p-α-Fe2O3 semiconductor nanoparticles in hydrogen (HER) and oxygen (OER) evolution reactions and a combined full cell electrocatalyst system to electrolyze the water. We have observed a distinct electrocatalytic performance for both HER and OER by tuning the interplay between iron oxidation states Fe2+ and Fe3+ and utilizing phase-transformed iron oxide nanoparticles (NPs). The Fe2+ rich n-FeO NPs exhibited superior HER performance compared to p-α-Fe2O3 and Fe(OH)x NPs, which is attributed to the enhancement in n-type semiconducting nature under HER potential, facilitating the electron transfer for the reduction in H+ ions. In contrast, p-α-Fe2O3 NPs demonstrated excellent OER activity. An H-cell constructed using n-FeO||p-α-Fe2O3 NPs as cathode and anode achieved a cell voltage of 1.87 V at a current density of 50 mA/cm2. The cell exhibited remarkable stability after 30 h of activation and maintained the high current density of 100 mA/cm2 for 80 h with a negligible increase in cell voltage. This work highlights the semiconducting properties of n-FeO and p-α-Fe2O3 for the electrochemical water splitting system using the band bending phenomenon under the applied potential.

Study on the reaction mechanism of multi-source metallurgical dust for zinc extraction and iron enrichment

Multi-source metallurgical dust can realize the purpose of zinc extraction and iron enrichment by high-temperature reduction. In this paper, based on the zinc extraction and iron enrichment from multi-source metallurgical dust in rotary kiln process, thermodynamic calculations and reduction kinetic experiments were carried out to clarify the thermodynamic conditions and kinetic limiting factors of the reduction of Fe-Zn-C-O system of metallurgical dust, and to obtain the suitable parameters of reduction temperature and reaction time, etc. The results showed that Fe mainly existed in the form of Fe2O3 and Fe3O4 in metallurgical dust. Zn mainly existed in the form of ZnO and ZnFe2O4, with a small amount existed in ZnS. The starting temperatures of the reduction of ZnO, ZnFe2O4, ZnS with C were 951.09 °C, 581.55 °C and 1862.44 °C, respectively. Combined with the temperature of the smelting condition of rotary kiln, it was known that the presence of ZnS was the key factor leading to the limitation of zinc removal rate. ZnO and ZnFe2O4 showed higher reduction difficulty compared to iron oxides, so the metallization rate of rotary kiln slag could be improved by controlling the smelting atmosphere. The weight loss rate, metallization rate and dezincification rate of multi-source metallurgical dust showed an increasing trend with the change of temperature and time, and the more desirable effect of weight loss rate, metallization rate and dezincification rate were 46.7%, 87.1%, and 92.5% under laboratory conditions at reduction temperature 1100 °C and reaction time 50 min.

Multi-Chambered Core/Shell Supraparticles for Real-Time, Full-Time Diagnosis and Treatment Integration of Tumors.

To a certain extent, theranostic nanoplatforms promote tumor treatment efficiency. However, timely monitoring of the critical stages and signal sustainability of the entire process is challenging. In this study, multi-chambered core/shell magnetic nanoparticles (MC-MNPs) as drug and imaging agent multi-loaded nanocarriers with a synergistic release function are reported. Supraparticles with stable chambers are formed by the supercooling self-assembly of several core/shell magnetic nanoparticles composed of amphiphilic copolymers as the core and hydrophilic magnetic iron oxide nanoparticles as the shell. Desalinized doxorubicin and coumarin 6 are stored in different cavities of nanocarriers, and chitosan is used as an outer encapsulation layer. Based on their construction properties, MC-MNPs can exhibit gradient-degraded and steady-released controllability in the tumor environment. Furthermore, real-time accumulation situations and full-time diagnostic signals of nanocarriers are thoroughly demonstrated using fluorescence imaging and T2-weighted magnetic resonance imaging before and after magnetic hyperthermia in targeted tumors under an alternating magnetic field. Thus, MC-MNPs as theranostic nanocarriers exhibit great potential for the timely monitoring and full-time guidance of tumor treatment.

Mentha spicata Mediated Formulation of Iron Oxide Nanoparticles Exhibit Superior Antimicrobial, Antioxidant, and Photodegradation Propensity Compared to Chemically Formulated Counterparts

Introduction: Iron oxide nanoparticles demonstrate tremendous potential in preserving the ecological balance of the environment since they act as antimicrobial agents and efficient photocatalysts. However, environmental sustainability has challenged the synthesis protocols of nanomaterials. Method: This study compares the green synthesis method with the scalable chemical synthesis method. In this work, Iron oxide nanoparticles were fabricated via the green chemistry technique utilizing the leaf extract of Mentha spicata (M-IONP) and also via the chemical co-precipitation method (C-IONP). The synthesized IONPs were analyzed by different characterization methods such as XRD, FTIR, SEM analysis, ZETA potential measurements, and DLS spectroscopy analysis. Results: The biosynthesized and chemically synthesized IONPs were analyzed for their mechanistic action against different applications like antimicrobial, antioxidant, and degradation of harmful dyes. Interestingly, the biosynthesized IONPs (M-IONP) exhibited more effective antimicrobial efficacy towards Gram-positive and Gram-negative organisms than chemically synthesized IONPs. Conclusion: The green synthesized M-IONP also showed significant antioxidant propensity similar to that of the standards taken. Additionally, green-synthesized M-IONP exhibited enhanced degradation efficacies against Methylene blue, chromium, and sulphamethoxazole in comparison to chemically synthesized IONP.

Trace metal distribution in seagrass-vegetated sediments of an urbanized estuary in Queensland, Australia

Seagrasses increase sediment complexity by trapping particulates and influencing biogeochemical cycles via root oxygen loss and organic matter exudation. However, their impact on trace metal sequestration is poorly studied. We found significantly higher trace metal concentrations in seagrass sediments compared to adjacent bare sediments, correlating with total organic carbon, iron, and fine sediments. Sequential extractions showed that most trace metals were dominated by recalcitrant fractions (oxidizable and residual fractions), representing phases such as organic matter, iron sulfides, and crystalline iron oxides. Depth-dependent trends in trace metal partitioning were evident. For example, arsenic in the oxidizable fraction only weakly correlated with Fe in surface sediments (rsp = 0.55) but correlated strongly in deeper sediments (rsp = 0.87), consistent with iron sulfides being a dominant host-phase. Overall, these results suggest that the unique geochemical conditions facilitated by seagrasses play an important role in sequestering trace metals in urban estuarine sediments.

Preparation of magnetic scaffolds via supercritical carbon dioxide foaming process using iron oxide nanoparticles coated with CO2‐philic materials as nucleating agents

AbstractThe iron oxide nanoparticles (IONs), coated with different materials, are synthesized and utilized as nucleating agents to prepare magnetic multi‐modal porous scaffolds of poly (lactic‐co‐glycolic acid)/IONs using the supercritical carbon dioxide (ScCO2) foaming process. The effects of the modification materials, including citric acid, polycaprolactone, and polyvinyl acetate, on the foaming process and properties of the magnetic scaffolds are systematically investigated. The results indicate that the solubility and diffusion ability of CO2 in the foaming materials played a vital role in the foaming process. The use of CO2‐philic materials and high pressure proves beneficial in generating micropores. The scaffolds with multi‐modal porous structures can be obtained at relatively low pressure for the ScCO2 foaming systems evaluated in this study. Furthermore, the prepared scaffolds exhibit high porosity and a good compressive modulus (higher than 0.4 MPa), satisfying the requirements of tissue engineering for soft tissue scaffolds.

A novel sequential extraction method for the measurement of Cr(VI) and Cr(III) species distribution in soil: New insights into the chromium speciation

The distribution characteristics of Cr(VI) species in contaminated soil is crucial for soil remediation; however, there is currently a lack of methods for analysing anionic Cr(VI) species in soil. This study has developed a novel sequential extraction method for speciation of Cr(VI) and Cr(III). Besides extraction experiments, simulated chromium species were prepared to verify the presence of proposed chromium species. The results show that Cr(VI) species in soil can be categorized into water-soluble Cr(VI), electrostatically adsorbed Cr(VI), Cr(VI) specifically adsorbed by minerals containing exchangeable Ca2+, Cr(VI) specifically adsorbed by hydrous metal oxides, calcium chromate Cr(VI) and stable complexed adsorption Cr(VI). These Cr(VI) species can be selectively extracted by specific solutions through ion exchange or weak acid dissolution. The most stable Cr(VI) species is Cr(VI) complexed by hydrous iron oxides through bidentate ligand binding; only by dissolution of hydrous iron oxides can this Cr(VI) species be leached. The distribution of Cr(VI) species is closely linked to particular soil compositions including exchangeable Ca2+ and hydrous iron oxides which determinate the Cr(VI) adsorption in soil. Cr(III) species comprise Fe-Cr coprecipitate hydroxides Cr(III), Fe-Mn oxide-bound Cr(III), organic matter-bound Cr(III) and residual Cr(III). Their distribution depends on the types of reductants present in the soil.

Effect of iron oxidation state on the catalytic performance of Fe/C in liquid phase flow hydrogenation of 2-butyne-1,4-diol

Cis-2-butene-1,4-diol and 1,4-butanediol are crucial precursors in producing bioplastics and biodegradable plastics. Moreover, cis-2-butene-1,4-diol is used in the production of vitamins A and B6, fungicides and insecticides. On an industrial scale, they are produced by hydrogenation of 2-butyne-1,4-diol with Ni Raney as catalyst at > 160 °C and > 15 MPa. Herein, the effect of mesoporous carbon, iron loading (2, 6, 10 and 14 wt%), and metal oxidation state on the activity and selectivity of iron catalysts in the liquid phase continuous flow 2-butyne-1,4-diol hydrogenation at mild conditions (at temperature range 10–65 °C and pressure range 1–20 bar) was performed. Catalytic investigations supported by statistical modeling and physicochemical characterization (TPR, H2-TPD, physisorption, TEM, XPS, and Mössbauer spectroscopy), showed that the activity of the Fe/C can be determined by the presence of functional groups in mesoporous support which are responsible for high metal dispersion and strong metal-support interaction, which boosts the catalytic activity of iron catalysts. Additionally, the formation of metastable iron carbides which are active in hydrogenation cannot be excluded. All of the catalysts showed 100% selectivity toward cis-2-butene-1,4-diol at the lowest temperature. However, the best compromise between selectivity and activity (TOF=336 h−1) was achieved with 2 wt% Fe at 1 bar and 25 °C.

Engineered metal nanoparticles for precision drug delivery: Pioneering the future of medicine: Mini review

AbstractMetal nanoparticles (NPs) have emerged as crucial components in precision drug delivery, presenting innovative opportunities to significantly enhance therapeutic efficacy and targeting accuracy. This review investigates recent developments in the engineering of metal NPs, emphasizing their distinctive properties and novel applications in drug delivery systems. A comprehensive analysis is performed on gold, silver, iron, and zinc oxide NPs, emphasizing their exceptional physicochemical properties and enhanced drug‐loading capacities. These features collectively enable the development and implementation of targeted and controlled drug delivery systems, indicating a new era of advanced therapeutic approaches. This review article accomplishes this by reflecting on the transformative potential of metal NPs, envisioning heightened efficacy, minimized side effects, and improved patient outcomes within the dynamic landscape of drug delivery platforms.

Uptake of K20-coated iron oxide nanoparticles by adrenocortical carcinoma cells

Uptake of K20-coated iron oxide nanoparticles by adrenocortical carcinoma cells

Exploration of Metal-Doped Iron Oxide Nanoparticles as an Antimicrobial Agent: A Comprehensive Review

Exploration of Metal-Doped Iron Oxide Nanoparticles as an Antimicrobial Agent: A Comprehensive Review

Oxidation of sulfur, hydrogen, and iron by metabolically versatile Hydrogenovibrio from deep sea hydrothermal vents.

Chemolithoautotrophic Hydrogenovibrio are ubiquitous and abundant at hydrothermal vents. They can oxidize sulfur, hydrogen or iron, but none are known to use all three energy sources. This ability though would be advantageous in vents hallmarked by highly dynamic environmental conditions. We isolated three Hydrogenovibrio strains from vents along the Indian Ridge, which grow on all three electron donors. We present transcriptomic data from strains grown on iron, hydrogen or thiosulfate with respective oxidation and autotrophic CO2 fixation rates, RubisCO activity, SEM, and EDX. Maximum estimates of one strain's oxidation potential were 10, 24, and 952mmol for iron, hydrogen and thiosulfate oxidation and 0.3, 1, and 84mmol CO2 fixation, respectively, per vent per hour indicating their relevance for element cycling in-situ. Several genes were up- or downregulated depending on the inorganic electron donor provided. Although no known genes of iron-oxidation were detected, upregulated transcripts suggested iron-acquisition and so far unknown iron-oxidation-pathways.

Magnetic iron-based nanoparticles encapsulated in graphene/reduced graphene oxide: Synthesis, functionalization and cytotoxicity tests

Nanomaterials for suitable particle sizes, shapes, surface properties, biocompatibility, magnetic properties, and chemical stability are candidates for biomedical applications. Among these nanomaterials, iron-based ones are highly interested in their morphological and magnetic properties for potential utilizations in biomedicine. However, iron-based nanoparticles lose their chemical stability in body fluids because of their oxide formations and transformations. Their use in biomedical applications, especially in imaging, may be less effective if they are oxidized and have lower magnetization values. Thus, the idea of coating them with a protective layer has recently emerged to prevent magnetic nanoparticles from degrading in human fluids and losing their magnetic properties. However, the biological effects of these coated nanoparticles on human cells are poorly understood. In this paper, the synthesis of multilayer graphene (MLG) encapsulated iron-based nanoparticles was investigated by solvothermal and chemical vapor deposition (CVD) methods followed by purification. Subsequently, their surface modification was conducted with pyrene end-functional POEGMA obtained by atom transfer radical polymerization (ATRP). Cytotoxicities of synthesized nanoparticles were evaluated in MCF7 cell lines, which is a commonly used model for breast cancer research. We also compare the results with those obtained from bare iron oxide nanoparticles (IONPs) and iron oxides that were embedded in reduced graphene oxide (rGO) or partially coated with it. We aim to evaluate the safety and efficiency of these nanoparticles and increase their chemical stability as a multifunctional nano platform for cancer diagnosis and treatment. Characterization techniques such as XRD, XPS, SEM, TEM, DTA/TG, DLS, zeta potential, BET, NMR, FTIR, and VSM were performed on the nanoparticles. Cytotoxicity assessments on MCF-7 cell lines indicated the potential of these graphene-based magnetic nanoparticles for biomedical applications, particularly drug delivery, due to their small size, soft ferromagnetic properties, high chemical stability, and cytocompatibility at concentrations below 500 μg/mL over short incubation times.

In-situ hydrothermal upgrading and mechanism of heavy oil with nano-Fe2O3 in the porous media

Hydrothermal upgrading is a promising technology for heavy oil, yet the impact of reservoir conditions on the catalytic effect of catalysts and the pathway are not clear. In this study, the effect of the formation environment on the catalytic upgrading process was investigated through simulating the reservoir conditions (2000 mD permeability, 25 % porosity) for catalytic hydrothermal cracking of heavy oil. Under the hydrothermal upgrading conditions（240 ℃, 24 h, 50 wt%, 0.1 wt% nano-Fe2O3）, 9.15 % of the heavy component(5.1 % resin and 4.05 % asphaltene) was converted to light component. The content of hydrocarbons below C17 in the saturated fraction increased from 36.29 % to 59.85 %. The structure of the asphaltene was disrupted resulting in a lower level of asphaltene stacking, and NC/NH ratio increased 13.61 % compared to heavy oil. In addition, the reservoir condition with quartz as the supporting medium improved the catalytic ability of iron oxide nanoparticles. When injected into the reservoir medium, nano-size facilitated dispersion on the surface of the proppant and inhibited the aggregation of nanoparticles, which ensured the continuous operation of the active sites on the surface of the catalyst. Electron transfer of Fe2+/Fe3+ catalyzed the heterolytic cleavage of covalent bonds of H2O/heavy oil molecules was the mechanism for heavy oil upgrading. These findings demonstrated the feasibility of in-situ upgrading of heavy oil through the use of nano-catalysts under reservoir conditions.