Octadecyl-modified Silica Research Articles

Development of HPLC system that uses phase-separation multiphase flow as an eluent.

We developed a new type of HPLC system that uses phase-separation multiphase flow as an eluent. A commercially available HPLC system with a packed separation column filled with octadecyl-modified silica (ODS) particles was used. First, as preliminary experiments, 25 kinds of mixed solutions of water/acetonitrile/ethyl acetate and water/acetonitrile were supplied to the system to act as eluents at 20°C. 2,6-Naphthalenedisulfonic acid (NDS) and 1-naphthol (NA) mixture was used as a model and mixed analyte was injected into the system. Roughly speaking, they were not separated in organic solvent-rich eluents and well separated in water-rich eluents, in which NDS eluted faster than NA. This means that HPLC worked under a reverse-phase mode for separation at 20°C. Next, the separation of the mixed analyte was examined on HPLC at 5°C, and then after judging the results, four kinds of ternary mixed solutions were in detail as eluents on HPLC at 20°C and 5°C. Based on their volume ratio, the ternary mixed solutions acted as a two-phase separation mixed solution, leading to a phase-separation multiphase flow. Consequently, the solutions flowed homogeneously and heterogeneously in the column at 20°C and 5°C, respectively. For example, the ternary mixed solutions containing water/acetonitrile/ethyl acetate at volume ratios of 20:60:20 (organic solvent-rich) and 70:23:7 (water-rich) were delivered into the system as eluents at 20°C and 5°C. In the organic solvent-rich eluent, the mixture of NDS and NA was not separated at 20°C but was separated at 5°C, the elution of NA being faster than the one of NDS (phase-separation mode). In the water-rich eluent, the mixture of analytes was separated at both 20°C and 5°C, the elution of NDS being faster than the one of NA. The separation at 5°C was more effective than at 20°C (reverse-phase mode and phase-separation mode). This separation performance and elution order can be attributed to the phase-separation multiphase flow at 5°C.

RP-18 TLC and Computational Descriptors of Skin Permeability of Sunscreens

The relationships between the reversed-phase thin layer chromatographic retention parameters obtained on octadecyl-modified silica (RP-18) sorbent for mobile phases containing water and one of six water-miscible organic modifiers (acetone, methanol, acetonitrile, tetrahydrofurane, N,N-dimethylformamide, 1,4-dioxane) and skin permeability coefficients were studied for a group of 21 cosmetic raw materials, mainly organic sunscreens and preservatives. The correlations between the skin permeability coefficients log K_d calculated in silico using EpiSuite software and the RP-18 thin layer chromatographic retention parameters are mostly linear, especially for compounds of lower-to-medium lipophilicity. It was established that skin permeability coefficient models based on retention parameters collected for mobile phases containing acetone or dioxane (75% v/v), proposed for structurally unrelated cosmetic raw materials are also applicable to other actives, as shown using a test set of compounds whose in vivo log K_d data are available. Skin permeability models developed in this study have the benefit of being based on easily obtained, chromatographic descriptors and their applicability extends beyond cosmetic chemistry.

Development and Validation of QuEChERS Followed by UHPLC-ToF-MS Method for Determination of Multi-Mycotoxins in Pistachio Nuts.

Pistachios are one of the types of tree nut fruits with the highest mycotoxin contamination, especially of aflatoxins, worldwide. This study developed a Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) method that was followed by Ultra-High Performance Liquid Chromatography combined with Time-of-Flight Mass Spectrometry (UHPLC–ToF-MS) for the determination of mycotoxins in pistachios. Different approaches to dispersive solid phase extraction as a clean-up method for high lipid matrices were evaluated. For this, classic sorbents such as C18 (octadecyl-modified silica) and PSA (primary secondary amine), and new classes of sorbents, namely EMR-Lipid (enhanced matrix removal-lipid) and Z-Sep (modified silica gel with zirconium oxide), were used. The QuEChERS method, followed by Z-Sep d-SPE clean-up, provided the best analytical performance for aflatoxins (AFB1, AFB2, AFG1 and AFG2), ochratoxin A (OTA), zearalenone (ZEA), toxin T2 (T2) and toxin HT-2 (HT2) in pistachios. The method was validated in terms of linearity, sensitivity, repeatability, interday precision and recovery; it achieved good results according to criteria imposed by Commission Regulation (EC) no. 401/2006. The method was applied to real samples and the results show that pistachios that are available in Portuguese markets are safe from mycotoxins that are of concern to human health.

Analysis of pesticide residues in commercially available chenpi using a modified QuEChERS method and GC-MS/MS determination

To ensure the safety of the commercially available chenpi, a convenient and fast analytical method was developed for the determination of 133 pesticide residues in chenpi using gas chromatography-tandem mass spectrometry (GC-MS/MS). In this study, different extraction solvents, redissolution solvents and adsorbents were tested according to the recovery and purification effect to obtain a modified QuEChERS method. The samples were extracted with acetonitrile. During the clean-up step, octadecyl-modified silica (C18) and graphitized carbon black (GCB) were selected, and aminopropyl (NH2) was used instead of primary secondary amine (PSA) because of its weaker ion exchange capacity which had little effect on the recovery of ditalimfos. Samples were quantified by matrix-matched calibration with internal standards. All pesticides showed good linearity in the respective range, both with values of r2 > 0.99. The average recoveries of the pesticides spiked samples ranged from 70.0% to 112.2% with the RSDs of 0.2%–14.4%. The modified QuEChERS method was validated and applied to twenty real samples. Five pesticides were found in eight batches, but no pesticide exceeded the maximum residue limits (MRL, MRL reference to European commission).

Simultaneous determination of PUFA-derived pro-resolving metabolites and pathway markers using chiral chromatography and tandem mass spectrometry

Lipid mediators play an important role as biological messengers involved in inflammatory processes. Deriving from different polyunsaturated fatty acids, endogenously built mediators featuring both pro- and anti-inflammatory properties as well as pro-resolving lipid mediators and their biological precursors have been investigated. A newly developed method using chiral chromatography-tandem mass spectrometry on human plasma has demonstrated its suitability for the simultaneous determination of prostaglandins, lipoxins, D-series derived resolvins as well as protectins, maresin 1, leukotriene B4 and several precursors of them in order to yield information about metabolic pathways. Due to the matrix complexity, a solid phase extraction method using an octadecyl-modified silica gel cartridge was carried out. The developed method allows the determination of 34 analytes in 25 min showing enough selectivity as well as precision and accuracy (≤15% relative standard deviation, ≤15% relative error) in the calibration range of 0.1–10 ng mL−1 or 0.2–20 ng mL−1 depending on the analytes. Stability of the analytes in plasma has been demonstrated for at least 3 h at room temperature, 72 h in the autosampler and 60 days in the freezer at −80 °C. This method has been validated and shown its suitability for the determination of all studied analytes in human plasma samples.

A Multiresidue Method for Simultaneous Determination of 116 Pesticides in Notoginseng Radix et Rhizoma Using Modified QuEChERS Coupled with Gas Chromatography Tandem Mass Spectrometry and Census 180 Batches of Sample from Yunnan Province

A method was established for the simultaneous determination of 116 pesticide residues in Notoginseng Radix et Rhizome with a combination of the modified QuEChERS method and GC–MS/MS. The sample was extracted with acetonitrile, cleaned up by primary–secondary amine and octadecyl-modified silica (C18) sorbents and determined by GC–MS/MS in multireaction monitoring mode. Matrix-matched calibration coupled with internal standard method was applied to compensate for the matrix effect and to quantify the pesticides. The results of all the 116 pesticides showed good linearity in the respective linear range with correlation coefficients (r2) > 0.99. The method limits of quantification were between 0.01 and 0.05 mg kg−1. The recoveries were between 64.3 and 119.4%, with RSD values typically lower than 18.3% at three spiked levels of 0.05, 0.10 and 0.20 mg kg−1. The validated methodology is easy, fast, highly accurate, reliable and sensitive for monitoring and quantification of the 116 pesticide residues in Notoginseng Radix et Rhizoma. In 180 batches of real samples, 11 pesticides were detected and among these quintozene and cyfluthrin were in excess of the standard of European Union maximum residue level for herbs.

Development and evaluation of microwave-assisted and ultrasound-assisted methods based on a quick, easy, cheap, effective, rugged, and safe sample preparation approach for the determination of bisphenol analogues in serum and sediments.

Microwave- and ultrasound-assisted methods based on a quick, easy, cheap, effective, rugged, and safe sample preparation approach followed by high-performance liquid chromatography with tandem mass spectrometry were developed for the simultaneous determination of eight bisphenol analogues in serum and sediment. The developed methods provided satisfactory extraction efficiency for the energy provided by microwaves and ultrasound. Compositions of commercial sorbents (primary secondary amine, MgSO4 , octadecyl-modified silica, and graphitized carbon black) were evaluated. The ultrasound-assisted method was suited for serum using primary secondary amine, MgSO4 , and octadecyl-modified silica as sorbents and a mixture of hexane and ethyl acetate as extraction solvent. The microwave-assisted method worked better for sediment with tetrahydrofuran and methanol as solvents and primary secondary amine, MgSO4 , octadecyl-modified silica, and graphitized carbon black as sorbents. Other experimental parameters, such as extraction temperature and time, were also optimized. The inter- and intraday relative standard deviations ranged from 2.7 to 5.5%. The limits of detection were between 0.1 and 1.0ng/mL for serum and between 0.1 and 0.5ng/g dry weight for sediment. The proposed methods were successfully applied to seven sediment and 20 human serum samples. The results showed that the developed methods were practical for the analysis and biomonitoring of bisphenols in sera and sediment.

Simple procedure for determination of the carbon content in silica-supported materials

A simply and accurate analytical method was developed to determination the carbon content in silica-supported materials. The principle of this method was to oxidize sample by a strong oxidant like potassium dichromate to produce carbon dioxide and this gas is absorbed into an alkaline solution for subsequent titration. The repeatability and the recovery of this method fell into the required range (% RSD <1.3 % and 98-102 % in recovery) of AOAC International. The chloride content of up to 100 mg did not give any influence. The developed procedure was applied to determine the carbon content in octadecyl-modified silica samples.

Simple and fast analysis of tetrabromobisphenol A, hexabromocyclododecane isomers, and polybrominated diphenyl ethers in serum using solid-phase extraction or QuEChERS extraction followed by tandem mass spectrometry coupled to HPLC and GC.

Two simplified sample preparation procedures for simultaneous extraction and clean-up of tetrabromobisphenol A, α-, β-, and γ-hexabromocyclododecane and polybrominated diphenyl ethers in human serum were developed and validated. The first procedure was based on solid-phase extraction. Sample extraction, purification, and lipid removal were carried out directly on an Oasis HLB cartridge. The second procedure was a quick, easy, cheap, effective, rugged, and safe-based approach using octadecyl-modified silica particles as a sorbent. After sample extraction and cleanup, tetrabromobisphenol A/hexabromocyclododecane was separated from polybrominated diphenyl ethers by using a Si-based cartridge. Tetrabromobisphenol A and hexabromocyclododecane were then detected by high-performance liquid chromatography coupled to tandem mass spectrometry, while polybrominated diphenyl ethers were detected by gas chromatography coupled to tandem mass spectrometry. The results of the spike recovery test using fetal bovine serum showed that the average recoveries of the analytes ranged from 87.3 to 115.3% with relative standard deviations equal to or lower than 13.4 %. Limits of detection of the analytes were in the range of 0.4-19 pg/mL except for decabromodiphenyl ether. The developed method was successfully applied to routine analysis of human serum samples from occupational workers and the general population. Extremely high serum polybrominated diphenyl ethers levels up to 3.32 × 104 ng/g lipid weight were found in occupational workers.

Multivariate assessment of lipophilicity scales—computational and reversed phase thin-layer chromatographic indices

Needs for fast, yet reliable means of assessing the lipophilicities of diverse compounds resulted in the development of various in silico and chromatographic approaches that are faster, cheaper, and greener compared to the traditional shake-flask method. However, at present no accepted “standard” approach exists for their comparison and selection of the most appropriate one(s). This is of utmost importance when it comes to the development of new lipophilicity indices, or the assessment of the lipophilicity of newly synthesized compounds. In this study, 50 well-known, diverse compounds of significant pharmaceutical and environmental importance have been selected and examined. Octanol-water partition coefficients have been measured with the shake-flask method for most of them. Their retentions have been studied in typical reversed thin-layer chromatographic systems, involving the most frequently employed stationary phases (octadecyl- and cyano-modified silica), and acetonitrile and methanol as mobile phase constituents. Twelve computationally estimated logP-s and twenty chromatographic indices together with the shake-flask octanol-water partition coefficient have been investigated with classical chemometric approaches—such as principal component analysis (PCA), hierarchical cluster analysis (HCA), Pearson’s and Spearman’s correlation matrices, as well as novel non-parametric methods: sum of ranking differences (SRD) and generalized pairwise correlation method (GPCM). Novel SRD and GPCM methods have been introduced based on the Comparisons with One VAriable (lipophilicity metric) at a Time (COVAT). For the visualization of COVAT results, a heatmap format was introduced. Analysis of variance (ANOVA) was applied to reveal the dominant factors between computational logPs and various chromatographic measures. In consensus-based comparisons, the shake-flask method performed the best, closely followed by computational estimates, while the chromatographic estimates often overlap with in silico assessments, mostly with methods involving octadecyl-modified silica stationary phases. The ones that employ cyano-modified silica perform generally worse. The introduction of alternative coloring schemes for the covariance matrices and SRD/GPCM heatmaps enables the discovery of intrinsic relationships among lipophilicity scales and the selection of best/worst measures. Closest to the recommended logKOW values are ClogP and the first principal component scores obtained on octadecyl-silica stationary phase in combination with methanol-water mobile phase, while the usage of slopes derived from Soczewinski-Matyisik equation should be avoided.

A multi-residue method for simultaneous determination of 74 pesticides in Chinese material medica using modified QuEChERS sample preparation procedure and gas chromatography tandem mass spectrometry

The present study is focused on the development of an analytical method for the simultaneous analysis of seventy-four pesticides belonging to different chemical classes (organochlorines, organophosphates, pyrethroids, dinitroanilines, dicarboximides, triazoles, etc.) in Chinese material medica. The samples were extracted according to the acetate QuEChERS protocol. To reduce the amount of co-extracted compounds, n-hexane instead of acetonitrile was employed as the extraction solvent. To improve the overall recoveries of problematic basic and base-sensitive compounds, sodium acetate was used to adjust the pH to a neutral condition, and florisil combined with octadecyl-modified silica (C18) were utilized in the cleanup step. The samples were analysed by GC-MS/MS, and quantified by matrix-matched calibration. The validation study was carried out on two representative herbs, Chuanxiong Rhizoma and Angelica Sinensis Radix. In two matrices, the linearity of the calibration was good between 5 and 250 ng/mL concentration ranges, and the limits of quantification (LOQs) less than 0.01 mg/kg for most pesticides. At the LOQs and ten times the LOQs, the mean recoveries of almost all pesticides were within 70-120%, with relative standard deviations (RSDs) lower than 10%. The method was applied on twenty real samples. Seven batches of Chuanxiong and five batches of Danggui were found to contain the residues. The combination of modified QuEChERS and GC-MS/MS offers low cost of analysis as well as excellent accuracy and sensitivity. This method could be especially useful for trace analysis of pesticide residues in complex matrices.

Pesticide residues in chicken eggs – A sample preparation methodology for analysis by gas and liquid chromatography/tandem mass spectrometry

A sample preparation method was developed for the analysis of chicken eggs to determine 97 GC and 81 LC amenable residues, including organophosphates, organochlorines, pyrethroids, triazoles, carboxyl-containing compounds, and the indicator PCBs. Hereby, considerations were given to the recoveries of the analytes, the method's suitability for routine analysis, and the assessment of the clean-up effect, for which a simple thin layer chromatography was implemented to visualize the most important lipid classes.The procedure consisted of (I) the extraction by matrix solid phase dispersion, and the clean-up by means of (II) small-scale gel permeation chromatography (GPC) and (III) two different solid phase extractions (SPE) for GC and LC amenable analytes, as well as (IV) the quantification using GC–MS/MS and LC–MS/MS. Cyclohexane/ethyl acetate was chosen as extraction solvent due to its suitability for extracting strong non-polar but also more polar analytes. The classical GPC was scaled down to ensure a 50% lower solvent consumption. The comprehensive investigation of conventional and modern zirconium-oxide-coated SPE materials resulted in the selection of octadecyl-modified silica (C18) combined with primary secondary amine using acetonitrile as elution solvent for GC amenable analytes and pure C18 in combination with acidified methanol for LC amenable pesticides.Compared to the currently established EN 1528 method the sample preparation proposed offered a higher sample throughput and a lower solvent consumption. Furthermore, for the first time the clean-up effectiveness of the sample preparation steps was documented as shown by means of thin-layer chromatography.The validation of chicken eggs proved the fulfillment of the quality control criteria for 164 of the 178 analytes tested, mostly at the lowest validated level of 5μg/kg for pesticides and 0.5μg/kg for the single indicator PCBs. However, the analysis of strongly polar analytes was still problematic, which could be attributed to the extraction and the GPC step. Nevertheless, the successful investigation of EU proficiency test materials (EUPT AO 07–09) confirmed the comparability of the results with the currently established sample preparation procedures and demonstrated the potential of the applicability of the presented method to other matrices as exemplified for lean poultry meat and fatty liquid cream.

DEVELOPMENT AND VALIDATION OF A TLC METHOD FOR THE ANALYSIS OF SYNTHETIC FOOD-STUFF DYES

A novel reversed-phase thin-layer chromatographic (RP-TLC) method was developed for simultaneous determination of ten most commonly used artificial food dyes. The method was validated with respect to specificity, linearity, precision, and accuracy and compared with reversed-phase high performance liquid chromatography (RP-HPLC) method. In the case of TLC method horizontal developing technique was employed using octadecyl-modified silica as a stationary phase and 0.5 mol dm−3 ammonium sulfate in 30% of ethanol-water solution as a mobile phase. HPLC analysis was carried out using XDB-C18 column and gradient of mixture of aqueous ammonium acetate solution (0.1 mol dm−3, pH = 6.5) and MeOH/ACN (1:1, v/v). Colorants were detected at 450, 500, and 625 nm wavelengths. The TLC method proved to be suitable for quantitative determination in relatively wide range of concentrations (20–300 ng/band). Satisfactory values of limits of detection and quantitation were established for both techniques, although somewhat higher in the case of TLC, ranging from 2–10 ng/band, that is, 3–20 ng/band. Both methods can be applied with satisfactory precision and accuracy, with clear advantage of TLC for simultaneous analysis of six samples per hour.

Stimulation and release from neurons via a dual capillary collection device interfaced to mass spectrometry

Neuropeptides are cell to cell signaling molecules that modulate a wide range of physiological processes. Neuropeptide release has been studied in sample sizes ranging from single cells and neuronal clusters, to defined brain nuclei and large brain regions. We have developed and optimized cell stimulation and collection approaches for the efficient measurement of neuropeptide release from neuronal samples using a dual capillary system. The defining feature is a capillary that contains octadecyl-modified silica nanoparticles on its inner wall to capture and extract releasates. This collection capillary is inserted into another capillary used to deliver solutions that chemically stimulate the cells, with solution flowing up the inner capillary to facilitate peptide collection. The efficiency of peptide collection was evaluated using six peptide standards mixed in physiological saline. The extracted peptides eluted from these capillaries were characterized via matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) with low femtomole detection limits. Using the capillary collection system in small custom-fabricated culturing chambers, individual cultured neurons and neuronal clusters from the model animal Aplysia californica were stimulated with distinct neuronal secretagogues and the releasates were collected and characterized using MALDI-TOF MS.

On‐line microdialysis coupled solid‐phase extraction to decrease matrix interference in the HPLC analysis of urinary ketamine and its metabolites

A microdialysis sampling (MDS) on-line SPE (MDS/SPE) has been applied to redeem the detection after dilution to decrease matrix interference in the analysis of ketamine (K) and its two main metabolites, norketamine (NK) and dehydronorketamine (DHNK) in urine by HPLC. After being filtrated, diluted and adjusting the pH, K and its metabolites in the diluted sample solution were collected through MDS and then trapped on an on-line SPE for HPLC analysis. The optimal conditions for MDS/SPE were investigated and then applied to real sample analysis. Experimental results indicated that the MDS/SPE by using regenerated cellulose hollow fiber (8-cm length) and 1 mM sulfuric acid as the perfusate at 20 microL/min flow-rate to collect analytes from 100-fold diluted urine sample (20 mL at pH 6.0), and then having been trapped in octadecyl-modified silica phase SPE for 30 min, offered the optimum efficiency. The concentration levels of 41, 42 and 28% (m/m) for K, NK and DHNK, respectively, in urine were redeemed for determination. The detection limits were 0.38, 0.33 and 0.34 ng/mL (in 100-fold diluted sample) for K, NK and DHNK, respectively. The method provides a very simple, inexpensive and eco-friendly procedure to determine K, NK and DHNK in urine.

Residues of diflubenzuron on horse chestnut (Aesculus hippocastanum) leaves and their efficacy against the horse chestnut leafminer, Cameraria ohridella

Residues of the insect growth regulator diflubenzuron were quantified on horse chestnut (Aesculus hippocastanum L.) leaves treated with a diflubenzuron 480 g litre(-1) SC, Dimilin. To analyse the samples, an analytical procedure was developed involving a simple extraction step followed by high-performance liquid chromatography on an octadecyl-modified silica column with methanol + 0.01 M ammonium acetate mobile phase. The results showed diflubenzuron to be highly stable on horse chestnut leaves; more than 4 months (127 days) after application, 38% (on average) of the insecticide still remained on/in the leaves. The data confirmed biological observations showing diflubenzuron's long-term efficacy against the horse chestnut leafminer, Cameraria ohridella Deschka and Dimić, which is the most important pest of the horse chestnut in Europe. The hypothesis of possible penetration of diflubenzuron into the leaf mass is explored and discussed.

Polyaniline-coated silica gel

Silica gel microspheres 7 and 15 μm in diameter were coated with an overlayer of polyaniline camphorsulfonate or hydrochloride during the oxidative polymerization of aniline. Coated silica gel and polyaniline precipitate were separated using a difference in sedimentation rate. In an alternative approach, the microspheres were modified with polyaniline in the presence of 35 nm colloidal silica. This technique prevented the macroscopic precipitation of polyaniline. Coatings of neat, 3-aminopropyl- and octadecyl-modified silica gel with polyaniline hydrochloride were compared. The surface composition of coated microspheres was characterized by X-ray photoelectron spectroscopy. Potential applications of particles in electrorheology, organic catalysis, and in modeling of conductivity behavior in composites are demonstrated.

Biomimetic extraction of PAHs and PCBs from soil with octadecyl-modified silica disks to predict their availability to earthworms.

We developed a model to predict the availability of PAHs and PCBs to earthworms (Lumbricus terrestris L.) in soils. We related the uptake of PAHs and PCBs by earthworms to the extraction with octadecyl-modified silica disks (C18 disks). Eleven soils (data set A) were used to develop the model, and 14 additional soils (data set B) were used to validate it independently. The biota-to-soil accumulation factors (BSAFs) of higher molecular weight PAHs (> or =202 g mol(-1)) and PCBs were higher than the corresponding Cl8 disk-soil partition coefficients (Kdisk) in the soils of data set A. This suggested that PAHs and PCBs were not only partitioned between soil and earthworms but also selectively ingested or metabolized. Nevertheless, we could predict the BSAFs of individual PAHs and PCBs for data set A by regression equations of log BSAF on log Kdisk (r=0.47-0.87). To predict the BSAFs of all PAHs and PCBs, respectively, we derived a model for each compound class that uses Kdisk and K(ow) values. Both the compound and the compound-class specific model were suitable to predict the BSAFs of PAHs and PCBs in data set B within a factor of 10-15.

HPLC-FID with Superheated Water as the Eluent: Improved Methods and Instrumentation

In the current study, an HPLC-FID system using superheated water as the eluent is constructed and further improved. Signal stability during temperature programmed operation was improved by using separate thermostatting of the 50 μm capillary restrictor. Operating the restrictor at 75°C prevented the superheated water from sputtering in the restrictor. Conventional octadecyl-modified silica, thermostable polymeric reversed phase and carbon type HPLC columns were used. The feasibility of the system is demonstrated by the analysis of a variety of compounds such as alcohols and aldehydes. It is shown that increased temperatures decrease elution times and, in addition to this, frequently improve peak shapes and column efficiencies. The separation of lower aldehydes is performed at 175°C with a detection limit in the low μg/ml range. The possibility of temperature programming is demonstrated for the separation of a range of alcohols. Furthermore, it is shown that temperature programming can be used for sample enrichment. Large volume injection with low temperature enrichment resulted in good peak shapes and a significant improvement of the detection limit. In this way, detection limits of 0.2 μg/ml (ppm) could be obtained for the aldehydes studied. Finally, the possibilities of using mobile phase additives as, e.g., buffers were briefly examined.

Determination of fenbendazole, praziquantel and pyrantel pamoate in dog plasma by high-performance liquid chromatography

Simple and rapid high-performance liquid chromatographic methods were developed for the determination of fenbendazole, praziquantel and pyrantel pamoate in dog plasma. The combination of these drugs is the most powerful treatment against most types of worms. Blood plasma samples obtained in a pharmacokinetic trial were prepared using solid-phase extraction. Fenbendazole and praziquantel were analyzed simultaneously by reversed-phase high-performance liquid chromatography on an octadecyl-modified silica stationary phase employing acetonitrile–phosphate buffer (pH 3.0) eluent and ultraviolet detection at 220 nm. Pyrantel was analyzed separately on a base-deactivated reversed-phase column using methanol–tetrahydrofuran–ammonium acetate buffer (pH 4.6) eluent and ultraviolet detection at 317 nm. Average recoveries for fenbendazole, praziquantel and pyrantel pamoate were 76.8, 93.4 and 90.5%, respectively. Limits of quantitation were in the range of 15–25 ng/ml plasma.