Non-isothermal Crystallization Kinetics Research Articles

Enhancing the Non-Isothermal Crystallization Kinetics of Polylactic Acid by Incorporating a Novel Nucleating Agent.

Polylactic acid (PLA) is a widely recognized biodegradable polymer. However, the slow crystallization rate of PLA restricts its practical applications. In this study, camphor leaf biochar decorated with multi-walled carbon nanotubes (C@MWCNTs) was prepared using the strong adhesive properties of polydopamine, and PLA/C@MWCNTs composites were fabricated via the casting solution method. The influence of C@MWCNTs as a novel nucleating agent on the melt behavior and non-isothermal crystallization behavior of PLA was investigated using differential scanning calorimetry (DSC). The crystallization kinetic parameters were obtained through the Jeziorny, Ozawa, and Mo methods, and the crystallization activation energy of the PLA/C@MWCNTs composites was calculated by the Kissinger method. The results show that the PLA/C@MWCNTs composites exhibit higher crystallinity and crystallization temperatures than those of PLA. Non-isothermal crystallization kinetic analysis reveals that the Mo method better describes the non-isothermal crystallization kinetics of both PLA and PLA/C@MWCNTs composites. In addition, it was found that C@MWCNTs, despite increasing the crystallization activation energy, can act as an efficient nucleating agent to increase the crystallization rate of PLA. These experimental results provide valuable insights for enhancing the slow crystallization rates associated with PLA.

Non-Isothermal Crystallization Kinetics and Properties of CaO-Al2O3-SiO2 (CAS) Glass-Ceramics from Eggshell Waste, Zeolite, and Pumice.

In this study, the crystallization behavior, microstructure, and mechanical and physical properties of CaO-Al2O3-SiO2 (CAS)-based glass-ceramics prepared from eggshell waste, zeolite, and pumice were investigated using X-ray diffraction (XRD), differential thermal analysis (DTA), scanning electron microscopy (SEM), a nanoindentation tester, and the Archimedes method. XRD analysis revealed that anorthite and wollastonite crystalline phases precipitated in the glass-ceramic samples after sintering at temperatures of 1000 °C and 1100 °C. However, diffraction peaks belonging to the wollastonite phase disappeared after sintering at 1200 °C, while peaks representing the pseudowollastonite phase were detected together with anorthite in the samples. SEM images showed that the crystals become coarser as the sintering temperature increased, with the crystal morphology transitioning from needle-like to rod-like. The crystallization activation energy (Ea) and Avrami parameter (n), both kinetic parameters, were calculated from DTA curves plotted at different heating rates using the Kissinger, Ozawa, and Matusita approaches. The results indicated that the crystallization activation energy of the CASZ glass ranged from 406 to 428 kJ mol-1, while that of the CASP glass varied from 356 to 378 kJ mol-1, depending on the method used. Additionally, the Avrami constant (n) was calculated to be 3.33 for CASZ and 2.89 for CASP. The hardness and bulk density of the glass-ceramic samples were significantly affected by the porosity present in the structure, with the highest hardness and bulk density values achieved for the CASZ glass-ceramic sample at the initial sintering temperature of 1000 °C.

Effect of the synergistic interaction of zinc adipate, hydrotalcite and ethylene propylene rubber on the performances of polypropylene

Polypropylene (PP) is widely used in a range of areas due to its excellent physical and chemical properties, but its low-temperature brittleness and low-impact resistance largely limits its application. Hence, this study investigated the changes in mechanical and thermal properties of isotactic polypropylene (iPP) modified by the addition of the β-nucleating agent zinc adipate (ZnAA), the inorganic rigid particle hydrotalcite (HT), and the rubber elastomer bipropylene rubber (EPR). The structure and properties of modified PP were investigated by Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), electronic universal material testing machine, and simple-beam impact testing machine. At last, the non-isothermal crystallization kinetics of iPP was investigated by the Caze method. It was found that with the addition of EPR reached 30 wt%, the notched impact strength of iPP was 34.74 kJ/m2, which was 542.43 % higher than that of pure iPP, and more than twice as high as that of ZnAA and HT modification, and the relative crystallinity ( K β) value of the β-crystalline form reached 79.66 % when 10 wt% EPR was added to the iPP. The addition of ZnAA, HT and EPR could significantly increase the crystallisation peak temperature ( T c), shorten the half-crystallisation time ( t 1/2) and increase the crystallisation activation energy ( ΔE) of iPP.

An Improved Mampel Model of the Non-Isothermal Crystallization Kinetics of Fiber-Reinforced Thermoplastic Composites.

Fiber-reinforced thermoplastic composites (FRTPs) are gaining increasing attention and widespread use in engineering applications due to their high specific strength and stiffness, excellent toughness, and recyclability. The mechanical properties of these composites are closely tied to their crystallization process, making it crucial to accurately describe this phenomenon. Existing theoretical models for analyzing the non-isothermal crystallization of thermoplastic composites often face challenges relating to the complexity of obtaining multiple parameters and the difficulty of achieving a final relative crystallinity of 1. To address these issues, this paper introduces a novel functional form of the crystallization rate parameter K(T), tailored for engineering applications, and proposes an improved Mampel model. This model assumes K(T) to be zero before the onset of crystallization and also to be linearly dependent on temperature thereafter, ensuring that the final relative crystallinity reaches 1. The model requires only two easily accessible parameters: the initial crystallization temperature (Ts) and the linear slope (k). The simplicity of the model makes it particularly well suited to engineering applications. This provides a straightforward and effective tool for describing the non-isothermal crystallization kinetics of fiber-reinforced thermoplastic composites.

Liquid state properties and amorphous solidification kinetics of multicomponent Fe_{50-x}Co_{x}Cr_{14}Mo_{14}C_{9}B_{8}Tm_{5} alloys investigated under containerless processing conditions.

The liquid state thermophysical properties and amorphous solidification kinetics of Fe_{50-x}Co_{x}Cr_{14}Mo_{14}C_{9}B_{8}Tm_{5} (x=10, 15, 20, and 25) alloys were explored by electromagnetic and electrostatic levitation techniques. It was found that the surface tension of liquid alloys with Fe contents below 30 at.% had a strong temperature dependence. The high surface tension led to a sharp increase in the interfacial free-energy penalty. A high nucleation barrier was formed inside the melt, which greatly inhibited the nucleation rate. The liquid viscosity revealed the strong liquid feature of this alloy series, which became the dominant kinetic factor determining their solidification mechanisms. The high viscosity hindered atomic diffusion and delayed nucleation. The long crystallizing incubation time of Fe_{30}Co_{20}Cr_{14}Mo_{14}C_{9}B_{8}Tm_{5} ensured a strong glass-forming ability and a low critical cooling rate of 2.11×10^{3}Ks^{-1}. As a result, a bulk metallic glass rod with an 8-mm diameter was successfully prepared by a convenient casting procedure. This rod could remain in a glassy state at a higher temperature and over a wider temperature range due to its high glass-transition temperature and large undercooled liquid region. The apparent activation energy for nucleation was derived as 463.8 kJmol^{-1} according to the nonisothermal crystallization kinetics, indicating that the bulk metallic glass had to absorb a large amount of energy to overcome the potential barriers before nucleation and thus exhibited excellent thermal stability.

Non-isothermal crystallization kinetics and activation energy modeling of carbon nanotubes dispersed high-density polyethylene and polypropylene blends

The study presents the effect of the reinforcement of carbon nanotubes (CNT) into high-density polyethylene (HDPE) and polypropylene (PP) blends. The Avrami exponent of CNT blends ranges within the 1.3–1.6 range. It demonstrates the 3D growth of crystals and nucleation activity during crystallization. The change in the Ozawa exponent indicates a two-stage crystallization process. The values of the Mo exponent show that the nucleation activity is affected by changing temperatures during the cooling process and the formation of high-quality crystal growth. The activation energy of the HDPE/PP matrix is 420.5 kJ/mol and adding 1.5% CNT resulted in 369.9 kJ/mol for Run-3. The polymer chains encounter difficulties in transitioning during the cooling process and release a significant amount of energy. The composition of the nanofiller in the blend affects the nucleation activity of the crystals. The permeability of the pure HDPE/PP sample obtained from sorption studies is 1.05 × 10−5 m2/s and adding 1.5% CNT in Run-3 provides a permeability of 5.2 × 10−5 m2/s. The CNT has a homogeneous dispersion in the matrix to form a net-like morphology. The crystallinity index calculated using the Seagal method for HDPE/PP, Run-3, Run-4 and Run-5 is 75%, 75.8%, 77.34% and 78%, respectively.

Solid–liquid equilibria and non-isothermal crystallization kinetics of n-alkanes binary systems

Solid–liquid equilibria and non-isothermal crystallization kinetics of n-alkanes binary systems

Crystallization path and non-isothermal kinetics of the Zr59.5Cu14.4Ni11.6Al9.7Nb4.8 metallic glass under different heating rates

In this work, the crystallization path and non-isothermal kinetics upon heating of the Zr59.5Cu14.4Ni11.6Al9.7Nb4.8 metallic glass were investigated. The devitrification process consists the formation of phases in the sequence of icosahedral quasicrystal (IQ) phase, Ni-containing phases, and Cu-containing phases. Avrami exponents were calculated at various heating rates, providing insights into the non-isothermal crystallization kinetics. The IQ phase and Ni-containing phases are interface-controlled growth, while the Cu-containing phases are diffusion-controlled growth. In addition, a continuous heating transition (CHT) diagram with a heating rate range exceeding six orders of magnitude was constructed, and the crystallization mechanism under different heating rates was revealed. These findings enrich the understanding of crystallization path and kinetics of metallic glass.

Deciphering the role of FI catalyst’s C3 substituent on the non-isothermal crystallization kinetics of nascent disentangled UHMWPE

UH1 - UH4 were accessed using tetra-fluorinated phenoxy-imine catalysts (FI catalysts) with linear (allyl, n-propyl, 1-propenyl) or more steric demanding (isopropyl) C3 substituents ortho to the phenoxy-oxygen atom. To get a better understanding of the non-isothermal crystallization kinetics of these nascent ultra-high molecular weight polyethylenes (UHMWPEs), their thermo-rheological properties are investigated. Through the application of annealing-crystallization-melting thermal analysis and isoconversional method, it is verified that the samples are nascent disentangled UHMWPEs with higher crystallization rates compared to the commercial UHMWPE (CUH). The molar fraction of nascent entangled crystals and/or degree of supercooling have a significant influence on the non-isothermal crystallization kinetics of nascent disentangled UHMWPEs. Finally, under a lower supercooling, the electron-donating property and steric hindrance of C3 substituent strongly affect the synthesis and architecture of polyolefin which in turn has a specific non-isothermal crystallization kinetics.

Effects of molecular structure and temperature field on the crystallization behavior of poly(tetrafluoroethylene-co-perfluoroalkylvinyl ether)

Despite the wide industrial application of poly(tetrafluoroethylene-co-perfluoroalkylvinyl ether) (PFA) in semiconductor processing, its crystallization behavior has little been studied. In this work, three PFA resins with similar molecular weight but different comonomer content and distribution were synthetized. Then the non-isothermal crystallization kinetics and crystalline structures were studied by differential scanning calorimetry, polarizing optical microscopy, and X-ray diffraction systematically. It is found that the incorporation of comonomers destroys the chain regularity and reduces the crystallizability of PFA thermodynamically, while the comonomer insertion improves the chain flexibility to accelerate the crystal growth dynamically. When the comonomer content of PFA is low, both the nucleation and growth rates are quite fast, which is favorable for the formation of spherulite. As the comonomer content increases or distribute uniformly in the chain, the nucleation rate declines notably and the side groups distort the crystal cell to increase the spacing of [100] plane. Moreover, two-dimensional growth mode is dominant to form bundle-like structure when crystallizing at slow cooling, where nucleation is suppressed by growth. But three-dimensional symmetrical spherulite can be activated and perfected at high cooling rate due to the initiation of substantial nucleation sites. This unique crystallization behavior is opposite to that of conventional polymers, providing a guidance for the polymerization and processing of PFA.

An assessment of the mechanically alloyed equiatomic FeCoNiMnSi high entropy amorphous alloy for non-isothermal crystallization kinetics and magnetocaloric refrigeration application

We studied an equiatomic FeCoNiMnSi high entropy amorphous alloy successfully processed via mechanical alloying technique. The structural, magnetic, and magnetocaloric characteristics of the resulting materials were examined using X-ray diffraction, field emission scanning electron microscopy, high-resolution transmission electron microscopy, and a vibrating sample magnetometer. The structural analysis showed a prominent amorphous phase formation as the milling time increases from t = 0–35h of mechanical alloying. The differential scanning calorimetry was employed to investigate the non-isothermal crystallization kinetics of the 35-h milled sample. The results revealed that the milled powder consists of a single exothermic peak with its apparent activation energy (Eg, Ex, Ep) being determined using the Kissinger, Ozawa, and Augis-Bennett equations. The findings exhibit Ex > Ep > Eg, representing that nucleation is more complicated than the growth mechanism during the crystallization process. Meanwhile, under non-isothermal conditions, the Kissinger-Akahira-Sunose, Friedman, and Flynn-Wall-Ozawa models were calculated using the local activation energies that agree with the apparent activation energy. Furthermore, the Johson-Mehl-Avrami-Kolmogorov exponent (n) and Avrami-Ozawa combined [F(T)] models exhibit high-dimensional nucleation and growth with an increasing nucleation rate enabled by lowering the local activation energies as a function of degree of conversion with respect to temperature. In magnetic measurements, a feasible mathematical model was proposed as a novel strategy for predicting the value of saturation magnetization as a milling time function. The model has an exceptional predictive capability, confirmed by fitting other research outcomes. Finally, the proposed system also delivers the best magnetocaloric properties with a maximum magnetic entropy change of 3.70 Jkg−1 K−1 at 150 K curie temperature and a refrigeration capacity of 252.86 J/kg with 1000 Oe applied magnetic field.

Crystallization Kinetics and Melting Behavior of Novel Biobased Poly(butylene 2,5‐thiophenedicarboxylate)

AbstractPoly(butylene 2,5‐thiophenedicarboxylate) (PBTh) is a novel biobased semicrystalline polyester with superior thermal, mechanical, and gas barrier properties; however, the crystallization kinetics and melting behavior of PBTh have not been studied in detail so far. The crystallization kinetics of PBTh was first studied in this research. The Ozawa equation failed to describe the nonisothermal melt crystallization kinetics of PBTh due to the secondary crystallization. The crystallization activation energy value was calculated by the Friedman method, which was negative and exhibited the conversion dependence. The isothermal melt crystallization kinetics of PBTh was well described by the Avrami equation in a wide range of crystallization temperature from 84 to 120 °C. PBTh showed the fastest crystallization rate at 104 °C; moreover, the Avrami exponent value slightly varied between 2.2 and 2.7, suggesting the same crystallization mechanism within the investigated temperature range. PBTh displayed one or two melting endotherms depending on crystallization temperature, which was well explained by the melting, recrystallization, and remelting mechanism. In addition, the equilibrium melting point of PBTh was estimated to be 163.1 °C with the Hoffmann−Weeks equation.

Non-isothermal crystallization kinetics of biocomposites based on PLA/PHBV and spent coffee grounds

AbstractThis study deals with the modification of a predominantly amorphous poly(lactic acid) (PLA) by blending it with a semi-crystalline biopolymer, polyhydroxybutyrate-co-valerate (PHBV), which has a high crystallinity. The blends with different concentrations of PLA and PHBV were compounded with spent coffee grounds (SCGs) and processed by injection moulding. The structural, thermal and mechanical properties of the produced samples were investigated. Particular attention was paid to the effect of the presence of SCG and the concentration of PHBV in the blend on the crystallization kinetics and the heat deflection temperature (HDT). For equimolar blends, only a slight increase in HDT (about 5 °C) was observed, but the addition of PHBV suppressed the cold crystallization of PLA, which otherwise negatively affects the dimensional stability of injection moulded parts. A similar effect, but to a lesser extent, was achieved by adding SCG to the PLA matrix. Thus, it is clear that the material structures of PLA/PHBV blends and composites help to minimize additional shrinkage of the parts and increase their dimensional stability. Due to the co-continuous structure of the symmetric PLA/PHBV blends and the increase in the degree of crystallinity from 36 to 47% by annealing the produced samples, the heat deflection temperature increased from 65 up to 90 °C.

Chain heterogeneity of poly(lactic acid) and its influence on crystallization kinetics

Temperature rising elution fractionation (TREF) approach was used to separate a biodegradable poly(lactic acid) (PLA) resin into ten fractions and completely establish the relationship between chain microstructure and properties. The main fractions were mainly eluted at 100, 110, 114, and 118 °C, and their mass percentages were 7.98 wt%, 44.83 wt%, 19.64 wt%, and 11.90 wt%, respectively. Through the use of successive self-nucleation/annealing (SSA) thermal fractionation, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and 13C-nuclear magnetic resonance spectroscopy (13C NMR), the intermolecular and intramolecular differences of PLA were further explored. Fractions eluted at 90, 110, 118, and 126 °C were also chosen to research the non-isothermal cold crystallization kinetics, and fractions eluted at 110, 118, and 126 °C were chosen to explore the non-isothermal crystallization kinetics in order to simulate the real process. The findings demonstrated that the Liu-Mo approach were more suited the non-isothermal crystallization and non-isothermal cold crystallization kinetics of PLA. As the elution temperature increased, so did the stereoregularity of the fractions, the crystallization rate, the crystallization capacity, and the lamellar thickness. These will lay a foundation for its basic research and industrial application.

Manipulation of non-isothermal crystallization kinetics of poly(lactic acid) composite film by a novel nucleating agent

As a type of renewable and biodegradable polymer, poly(lactic acid) (PLA) has been widely used in various fields. However, its weak crystallization ability deteriorates the properties of the final product. In this work, a novel nucleating agent (MWCNTs@CeO2), multi-walled carbon nanotubes (MWCNTs) decorated with ceria (CeO2), was synthesized using the hydrothermal method and subsequently used to manipulate the non-isothermal crystallization kinetics and nucleation behavior of PLA. The results show that MWCNTs@CeO2 can act as an effective nucleating agent to accelerate the crystallization rate of PLA by reducing the half-crystallization time. In non-isothermal crystallization kinetics, the Avrami equation modified by Jeziorny cannot accurately describe the non-isothermal crystallization behavior of PLA and PLA/MWCNTs@CeO2 composite films, whereas the Mo method can. Furthermore, it is found that the addition of MWCNTs@CeO2 does not change the crystal structure of PLA, but increases the nucleation and growth rate of PLA, thereby promoting its crystallization.

The effect of tetra‐needle‐like zinc oxide whisker as additive on the crystallization kinetics of polybutylene adipate terephthalate/polylactic acid blend

AbstractHerein, we investigate the effect of the addition of tetra‐needle‐like zinc oxide whisker (T‐ZnOw), a novel reinforcing additive, on the melt crystallization behavior of biodegradable polybutylene adipate terephthalate (PBAT)/polylactic acid (PLA) polymer blends. PBAT and PLA were blended in a Haake mixer at a fixed weight ratio of 70/30, and the contents of T‐ZnOw varied from 0 to 7 wt%. The melt thermal properties and crystallization behavior of PBAT/PLA blends and PBAT/PLA/T‐ZnOw composites were studied using differential scanning calorimetry. The kinetics of melt crystallization have been quantitatively explained using a range of mathematical formalisms. The Avrami equation is adopted to analyze the isothermal crystallization process and kinetics of PBAT/PLA/T‐ZnOw composites. For its nonisothermal crystallization process and kinetics, the Ozawa equation cannot describe the entire process, while the Jeziomy‐modified Avrami equation can only describe the initial stage of its nonisothermal crystallization. Using Mo‐analysis, the impact of T‐ZnOw contents on the composite's nonisothermal crystallization kinetic has been thoroughly examined. Given that the PBAT/PLA blend system's crystal formation may be inhibited by T‐ZnOw, the observation demonstrates that T‐ZnOw only marginally alters this process. The work is of significant scientific value and adds a new concept to the development of sustainable thin film for packaging.Highlights T‐ZnOw is used as a novel additive for PBAT/PLA polymer blends. The crystallization of PBAT/PLA/T‐ZnOw composite systems is thoroughly examined. T‐ZnOw marginally reduces the kinetics of the crystallization process of PBAT/PLA blends. PBAT/PLA/T‐ZnOw composites follow volume nucleation with mixed 2D/1D growth. The nonisothermal crystallization of PBAT/PLA/T‐ZnOw composites is validated by Mo‐analysis.

Eco-friendly zinc-metal-organic framework as a nucleating agent for poly (lactic acid)

Eco-friendly poly(L-lactic acid) (PLA) can be made more versatile, and its crystallization rate is accelerated by adding Zinc-based metal-organic framework (Zn-MOF) particles. Using differential scanning calorimetry (DSC), the non-isothermal melt crystallization behavior of biodegradable PLA nucleated by 0.3 to 3 wt% of Zn-MOF was examined. The non-isothermal melt crystallization kinetics parameters were determined using a modified Avrami model and Mo approach. Zn-MOF dramatically accelerated the crystallization process, as evidenced by several non-isothermal crystallization metrics, including the crystallization half-time and crystallization rate constant. The melt crystallization temperatures of the PLA-Zn-MOF composites, with contents of 0.7 and 1 wt%, were increased by 21 °C compared to the neat PLA. Using the Friedman isoconversional kinetic method, the neat PLA and PLA-Zn-MOF composites' effective activation energy values, ∆E, were determined. The ∆E values of PLA-Zn-MOF from 0.3 to 1 wt% Zn-MOF composites were lower than that of neat PLA. Moreover, polarized optical microscopy revealed the formation of numerous small-sized PLA spherulites upon Zn-MOF addition. The results indicate that the Zn-MOF (at concentrations of 0.7 to 1.0 wt%) can be used as an efficient nucleating agent for PLA, where it increases the melt crystallization temperature, nucleation density, and crystallinity without changing the crystalline structure, while also significantly reduces the effective activation energy and the size of spherulites. Additionally, scanning electron microscopy confirms good dispersion of Zn-MOF (0.3 to 1 wt%) within the PLA matrix.

Non-isothermal crystallization kinetics, optical and structural properties of MgO-doped vanadate glasses

Non-isothermal crystallization kinetics, optical and structural properties of MgO-doped vanadate glasses

Effect of Nano Spinel Ferrites Co0.9Cu0.1Fe2O4 on Non-Isothermal Cold Crystallization Behaviours and Kinetics of Its Composites with Polylactic Acid.

Nanoparticles of spinel ferrites with a composition of Co0.9Cu0.1Fe2O4 (AM NPs) were effectively synthesized via a hydrothermal route. The structure of ferrite nanoparticles was characterized with X-ray diffraction, which showed a single cubic spinel phase. Energy-dispersive X-ray (EDX) spectroscopy and field emission-scanning electron microscopy (FE-SEM) were employed to analyse elemental composition and surface morphology, respectively. Moreover, the effects of the Co0.9Cu0.1Fe2O4 on the morphology of [PLA = polylactic acid] nanocomposites were examined through polarized light optical microscopy (POM) and X-ray diffraction (XRD). The thermal behaviours for tested samples were studied through [DSC = differential scanning calorimetry] and [TGA = thermal gravimetric analysis]. A great number of minor PLA spherulites were detected using POM in the presence of the Co0.9Cu0.1Fe2O4 ceramic magnetic nanoparticles (AM), increasing with AM nanoparticle contents. X-ray diffraction (XRD) analysis showed that the presence of nanoparticles led to an increase in the intensity of diffraction peaks. The DSC findings implied that the crystallization behaviours for the efficient PLA as well as its nanocomposites were affected by the addition of AM nanoparticles. They act as efficient nucleating agents because they shift the temperature of crystallization to a lower value. The Avrami models were used to analyse kinetics data. The experimental data were well described using the Avrami method for all samples tested. The addition of AM to the PLA matrix resulted in a decrease in the crystallization half-time t1/2 values, indicating a faster crystallization rate. TGA data showed that the occurrence of AM nanoparticles decreased the thermal stability of PLA.

Additive Manufacturing of Composite Polymers: Thermomechanical FEA and Experimental Study.

This study presents a comprehensive approach for simulating the additive manufacturing process of semi-crystalline composite polymers using Fused Deposition Modeling (FDM). By combining thermomechanical Finite Element Analysis (FEA) with experimental validation, our main objective is to comprehend and model the complex behaviors of 50 wt.% carbon fiber-reinforced Polyphenylene Sulfide (CF PPS) during FDM printing. The simulations of the FDM process encompass various theoretical aspects, including heat transfer, orthotropic thermal properties, thermal dissipation mechanisms, polymer crystallization, anisotropic viscoelasticity, and material shrinkage. We utilize Abaqus user subroutines such as UMATHT for thermal orthotropic constitutive behavior, UEPACTIVATIONVOL for progressive activation of elements, and ORIENT for material orientation. Mechanical behavior is characterized using a Maxwell model for viscoelastic materials, incorporating a dual non-isothermal crystallization kinetics model within the UMAT subroutine. Our approach is validated by comparing nodal temperature distributions obtained from both the Abaqus built-in AM Modeler and our user subroutines, showing close agreement and demonstrating the effectiveness of our simulation methods. Experimental verification further confirms the accuracy of our simulation techniques. The mechanical analysis investigates residual stresses and distortions, with particular emphasis on the critical transverse in-plane stress component. This study offers valuable insights into accurately simulating thermomechanical behaviors in additive manufacturing of composite polymers.