Non-biodegradable Plastics Research Articles

Use of polyethylene terephthalate fibres for mitigating the liquefaction-induced failures

The presence of non-biodegradable plastic waste is a serious concern for the health of endangered species. The present study is based on the sustainable utilisation of polyethylene terephthalate (PET) fibres obtained from waste plastic bottles to enhance the liquefaction resistance of fine sand. After performing a series of stress-controlled cyclic triaxial tests, the cyclic behaviour of PET-fibre reinforced sand has been investigated. The application of PET fibres was found to be more satisfactory in medium dense sand than that in loose sand as observed by residual excess pore water curves. In medium dense sand with 0.6% PET-fibres, the number of cycles to reach liquefaction was about 4 times that of the unreinforced sand. Using the dynamic shear modulus (G), the degradation index was calculated for both reinforced and unreinforced soils to assess stiffness characteristics. After nearly 50 loading cycles, the value of G/Gmax increased 2.55 times with the addition of 0.4% PET fibres in unreinforced sand. Based on the results obtained, a regression model has been developed for the calculation of number of liquefaction failure cycles (Ncyc,L) in correlation with several parameters, namely, relative density (Dr), fibre content (FC) and σd/σc′ (σd = deviator stress, σc′ = effective confining stress).

A review: Silver–zinc oxide nanoparticles – organoclay-reinforced chitosan bionanocomposites for food packaging

AbstractResearch on bionanocomposites has been developed, while its application as food packaging is still being explored. They are usually made from natural polymers such as cellulose acetate, chitosan (CS), and polyvinyl alcohol. Bionanocomposite materials can replace traditional non-biodegradable plastic packaging materials, enabling them to use new, high-performance, lightweight, and environmentally friendly composite materials. However, this natural polymer has a weakness in mechanical properties. Therefore, a composite system is needed that will improve the properties of the biodegradable food packaging. The aim of this mini-review is to demonstrate recent progress in the synthesis, modification, characterization, and application of bionanocomposites reported by previous researchers. The focus is on the preparation and characterization of CS-based bionanocomposites. The mechanical properties of CS-based food packaging can be improved by adding reinforcement from inorganic materials such as organoclay. Meanwhile, the anti-bacterial properties of CS-based food packaging can be improved by adding nanoparticles such as Ag and ZnO.

Field application of biodegradable microplastics has no significant effect on plant and soil health in the short term

Bioplastics (biodegradable plastics) potentially offer an encouraging alternative to conventional (petroleum-based) plastics. In practice, bioplastics inevitably generate a large number of bio-microplastics (bio-MPs, diameter <5 mm) during the degradation progress. However, the impact of bio-MPs on plant and soil health within agroecosystems remains incomplete. Here, a field study was conducted to investigate the effect of two shapes (fiber and powder) of pure polylactic acid (PLA) bio-MPs on oat (Avena sativa L.) and soybean (Glycinemax (L.) Merr.) growth and soil health. Our results showed that PLA application at a representative soil loading rate of 0.2% (w/w) had no significant effect on soil enzyme activities, soil physicochemical properties (soil water content, pH, etc.), root characteristics, plant biomass, and crop yield. Thus, we conclude that soil quality, plant health, and ecosystem multifunctionality were not affected by PLA over one growing season (5 months) in the presence of either bio-MP shape (fiber and powder) for either crop species (oat and soybean). Overall, PLA based bio-MPs may not pose a significant threat to agroecosystem functions in the short term (days to months) in the field, thus may provide a viable environmentally benign solution to replace traditional non-biodegradable plastics in agroecosystems.

Generation and consequence of nano/microplastics from medical waste and household plastic during the COVID-19 pandemic

Since the end of 2019, the world has faced a major crisis because of the outbreak of COVID-19 disease which has created a severe threat to humanity. To control this pandemic, the World Health Organization gave some guidelines like wearing PPE (personal protective equipment) (e.g., face masks, overshoes, gloves), social distancing, hand hygiene and shutting down all modes of public transport services. During this pandemic, plastic products (e.g., household plastics, PPE and sanitizer bottles) have substantially prevented the spread of this virus. Since the outbreak, approximately 1.6 million tons of plastic waste have been generated daily. However, single-use PPE like face masks (N95), surgical masks and hand gloves contain many non-biodegradable plastics materials. These abandoned products have created a huge number of plastic debris which ended up as microplastics (MPs) followed by nanoplastics (NPs) in nature that are hazardous to the eco-system. These MPs and NPs also act as vectors for the various pathogenic contaminants. The goal of this review is to offer an extensive discussion on the formation of NPs and MPs from all of these abandoned plastics and their long-term impact on the environment as well as human health. This review paper also attempts to assess the present global scenario and the main challenge of waste management to reduce the potential NP/MPs pollution to improve the eco-systems.

Comparison of Carbon-Nanoparticle-Filled Poly(Butylene Succinate-co-Adipate) Nanocomposites for Electromagnetic Applications.

Electrostatic dissipative (ESD), anti-static (AS), and electromagnetic interference (EMI) shielding materials are commonly based on commodity fossil-fuel-based plastics. This, in turn, contributes to ever-growing non-biodegradable plastic pollution. Graphene nanoplatelets (GN), multi-walled carbon nanotubes (MWCNT), nanostructured carbon black (NCB), and amorphous carbon black (CB) were utilized as nanofillers to prepare bio-based and biodegradable poly(butylene succinate-co-adipate) (PBSA) nanocomposites. Solvent-cast composites were prepared with 1.1 to 30.0 vol.% nanoparticle loading. The literature mainly focuses on relatively low loadings; therefore, for this research, filler loadings were increased up to 30 vol.% but the maximum loading for NCB and CB loadings only reached 17.4 vol.% due to a lack of dimensional stability at higher loadings. The composites were characterized using tensile testing, volumetric and surface conductivity measurements, thermal conductivity measurements, dielectric spectroscopy in the microwave region, and transmittance in the terahertz range. Tensile tests showed excellent carbon filler compatibility and enhanced tensile strength for loadings up to 5 vol.% (up to 20 vol.% for MWCNT). The highest thermal conductivity values were reached for the MWCNT filler, with the 30.0 vol.% filled composite reaching 0.756 W/mK (262% increase over PBSA). All fillers were able to produce composites that yielded volume conductivities above 10−10 S/m. Composites with MWCNT, GN, and NCB inclusions above the percolation threshold are suitable for EMI applications in the microwave and THz frequency range.

Dark side of a bio-based and biodegradable plastic? Assessment of pathogenic microbes associated with poly(butylene succinate-co-adipate) under ambient and future climates using next-generation sequencing.

Bio-based and biodegradable plastic mulching films have been proposed to replace the non-biodegradable plastic mulch films to solve plastic pollution problems in agricultural soils. However, the impact of bio-based and biodegradable plastics on plant and human health remains largely unexplored. Here, we aimed to assess the risk under field conditions of a bio-based and biodegradable poly(butylene succinate-co-adipate; PBSA), a widely used mulching film as carrier of potential pathogenic microorganisms (bacteria and fungi) at ambient and future climate conditions. Overall, we affiliated 64 fungal and 11 bacterial operational taxonomic units (OTUs) as pathogens by using Next-Generation Sequencing approach. Our results revealed that PBSA hosted at least 53 plant pathogens, of which 51 were classified as fungi, while the other two were bacteria. Most fungal plant pathogens were able to withstand the anticipated future climate changes. We detected 13 fungal and eight bacterial OTUs, which were classified as opportunistic human pathogens. Only one bacterial OTU (Enterococcus faecium) was assigned to a human pathogen. While future climate conditions only significantly impacted on the presence and frequency of detection of few pathogens, incubation time was found to significantly impacted on nine pathogens. This result demonstrates the temporal dynamics of pathogens associated with PBSA. The threats to plant and human health were discussed. We emphasize that the risks to human health are relatively low because we mainly found opportunistic pathogens associated with PBSA and the amount are comparable to the plant debris. However, the risks to plant health may be considered as moderate because many plant pathogens were discovered and/or enriched in PBSA. Furthermore, in soil environments, the pathogenic risk of plastic is highly depending on the surrounding soil pathobiome where plastic is being decomposed.

PHB Processability and Property Improvement with Linear-Chain Polyester Oligomers Used as Plasticizers.

In 2021, global petroleum-based plastic production reached over 400 million metric tons (Mt), and the accumulation of these non-biodegradable plastics in the environment is a worldwide concern. Polyhydroxybutyrate (PHB) offers many advantages over traditional petroleum-based plastics, being biobased, completely biodegradable, and non-toxic. However, its production and use are still challenging due to its low deformation capacity and narrow processing window. In this work, two linear-chain polyester oligomers were used as plasticizers to improve the processability and properties of PHB. Thermal analyses, XRD, and polarized optical microscopy were performed to evaluate the plasticizing effect on the PHB and the reflection on the mechanical behavior. Both oligomers acted as PHB plasticizers, with a reduction in Tg and Tm as a function of the plasticizer concentration, which can make it easier to handle the material in thermal processing and reduce the probability of thermal degradation. Plasticizer 2 proved to be the most promising between the two with an optimized condition of 20%, in which there was a decrease in elastic modulus of up to 72% and an increase in the maximum elongation of 467%.

Effects of polylactic acid (PLA) and polybutylene adipate-co-terephthalate (PBAT) biodegradable microplastics on the abundance and diversity of denitrifying and anammox bacteria in freshwater sediment

Microplastics (MPs) have been widely distributed on Earth and have drawn global concern for freshwater and marine ecosystems. Biodegradable plastics have risen in popularity to replace nonbiodegradable plastics all over the world. The effects of biodegradable plastics on denitrifying and anammox bacteria in freshwater sediment remain largely unknown. In this study, water column reactors containing polylactic acid (PLA) or polybutylene adipate-co-terephthalate (PBAT) MPs in sediment were established to simulate lake ecosystems and analyze the effects of biodegradable MPs on sedimentary nitrogen transformation microorganisms. The total organic carbon (TOC) concentrations in the PLA and PBAT groups were slightly higher than those in the control group, which might be related to the slow degradation of these two plastics. Denitrifying and anammox bacterial diversities decreased after adding MPs to sediments for 30 days, and the dominant OTUs of these two bacteria were differentiated from the control. The abundance levels of nirS denitrifying and anammox bacteria on the PLA MP surface were significantly higher than those in the other groups (P < 0.05), but they were lower in the PBAT groups than in the other groups. As an excellent electron donor for the denitrification process, lactic acid release from PLA degradation resulted in the enrichment of denitrifying and anammox bacteria on the MP surfaces. However, PBAT led to various responses of bacteria in an anaerobic environment. In addition, the redundancy analysis results indicated that total phosphorus, TOC and nitrate were strongly negatively correlated with the abundance levels of denitrifying and anammox bacteria. Our findings provided insight into the effects of MPs, especially the biodegradable ones, on sedimentary nitrogen-transformation bacteria.

Impact of buried debris from agricultural biodegradable plastic mulches on two horticultural crop plants: Tomato and lettuce

Biodegradable mulches (BDM) are increasingly valued and used for substituting non-biodegradable plastic mulches polluting agricultural soils. They are tilled into soil, where they fragment and release compounds throughout their biodegradation. The consequences of BDM use on the plant-soil environment have been partially studied with pristine and with artificially-weathered BDM fragments. However, to guarantee safety use of BDM, studies on the BDM debris effects are required. For this, to determine potential effects of the field-weathering BDM on plants, a mesocosm experiment was performed by sowing seeds from two major plant species commonly cultivated with BDM, tomato (Lycopersicon esculentum) and lettuce (Lactuca sativa), in plant pots containing pristine and field-weathered pieces from seven different BDM formulations, one paper mulch, a polyethylene (PE) mulch, and no-mulch control pots.Germination of both plant species was unaffected by any of the mulch treatments; however, PHB (polyhydroxybutyrate)-based BDM fragments severely inhibited tomato and lettuce plant growth, 90 and 95 %, respectively. Moreover, all pristine and field-weathered BDM significantly delayed lettuce plant development. Tomato plant growth progressed better, but growth retardation was also evidenced with most field-weathered BDM treatments. Overall, field-weathered fragments caused stronger effects on plants than the pristine unused ones. No effects were found for PE mulch, either pristine or field-weathered. The obtained results highlight that BDM debris may alter plant development depending on their nature and on their weathering, rather than on their physical presence, and evidence the need to conduct further experiments on the impact of field-weathered BDM on the plant-soil environment.

Review on Recycling of Microplastics in Cigarette Butts

It’s a lesser-known fact that the cigarette filter is made of cellulose acetate, a kind of non-biodegradable plastic and it takes almost 10 years for this ingredient to completely decompose. Cigarette smoking is on the rise throughout the world. Ever since tobacco smoking began there are both opponents and proponents for the same. Instead of getting into a discussion as to whether one should smoke or not; would like to focus on cigarette butts which a micro plastic that is harmful to the environment and needs to be disposed of in an appropriate manner to conserve the environment and human health. As the trend is today, cigarette smoking is on the increase. And in light of this event recycling cigarette butts give rise to a sustainable material.This paper will cover how cigarette butts can be collected and recycled to tackle the unfriendly and unsightly remains of cigarettes after smoking.

A REVIEW ON PREVALENCEOF BIODEGRADABLE PLASTIC IN CURRENT LIFE

Plastics have become an integral part of our lives. The problem of conventional plastics istaking decades to degrade in nature. Plastic waste is increasing every year and the precise time needed for biodegradation is unknown. Environmental awareness has driven the development of new biodegradable materials, especially for single use plastic items. Synthetic plastics provide a range of utilities in the civilization of mankind, at the same time the accumulation of these nonbiodegradable plastic in the environment is a menacing drawback increasing day by day. So thatthe management of plastic waste is a worldwide concern and also a substitute for plastic has become essential to us.

Metal-coordination and surface adhesion-assisted molding enabled strong, water-resistant carboxymethyl cellulose films

Developing renewable and biodegradable materials derived from cellulose is an attractive strategy to replace petroleum-derived plastics. In this study, metal ions (Cu2+, Fe3+, and Al3+) were added as a green binder into carboxymethyl cellulose (CMC) films to improve their mechanical properties and water resistance capacity. The tensile strengths of CMCAl3+ films were 133 MPa and 99 MPa at 43 % and 97 % humidity, respectively, which were comparable to or greater than those of the majority of commercially available plastics. Additionally, we proposed an interfacial adhesion-assisted molding strategy for forming cellulose-based films, avoiding film wrinkles and unevenness during drying and metal-coordination formation. The resultant films exhibited high transparency, excellent mechanical properties, water resistance capacity, ultraviolet light (UV) shielding, and antibacterial activity. In summary, the biodegradable, eco-friendly, excellent application performance, and adaptability of CMCMn+ (Mn+: polyvalent metal ions) films open new prospects as a viable alternative to non-biodegradable plastics.

Polyhydroxybutyrate As A Biopolymer

This project is about the use of biopolymer (PHB) as an alternative form in place of non-biodegradable plastic, many types of research have been done on this polymer which shows it sharesa similar application as that of conventional plastic and also are biodegradable and biocompatible. As synthetic polymers are cheap and inexpensive but are non-biodegradable and release toxicity that is hazardous for biomass so there is a need to switch on another alternative to reduce the dependence on conventional polymers. In recent years, the increasing population that resulted in urbanization and industrialization has led to a surge in petroleum-based plastics consumption. Due to its cheap availability and durability, there has been a great demand in every field. The continuous increase in the use of petrochemical plastic is the cause of various environmental pollution as it is non-biodegradable and take thousandof years to break down so produce toxins if it is disposed of in soil and water, even if they burnt that will increase the CO2 concentration in the atmosphere. There has been neededfor a biopolymer that can compete and reduce the dependency on hazardous plastics. Researchers have been looking for an alternative that would be eco-friendly and sustainable in nature as well as meet the current demand. Polyhydroxybutyrate (PHB) being biocompatible as well as biodegradable can be a better option to switch petroleum-based plastic as it possesses similar physical properties to that of propylene. PHB is a biopolymer that is a member of the PHA family.PHA are of three types based on the number of monomers present(Madison and Huisman 1999); the short-chain length consists of 3-5 units of carbon, medium chain length consists of 6-14 units of carbon, and the long-chain length consists of more than 15 units of carbon atoms(Anderson and Dawes 1990). The nature of PHB is brittle and crystalline as well as high melting and degradation point due to the presence of double bond that leads to the chemical variation and contrast structure(Colin et al, 2012).To improve its properties we have to blend it with other natural plasticizers such as (glycerol, soybean oil, triethyl citrate, salicylic ester) to reduce its brittleness and improve lowering temperature

Anthracnose Disease Control and Postharvest Quality of Hass Avocado Stored in Biobased PLA/PBAT/Pine Essential Oil/Chitosan Active Packaging Nets.

For sale in the domestic market, Hass avocados are kept in non-biodegradable plastic nets and stored at an ambient temperature. The fungus Colletotrichum gloeosporioides can cause important losses at this stage. Consequently, formulations based on polylactic acid (PLA)/poly (butylene adipate-co-terephthalate) (PBAT) 60/40 biodegradable blends added with pine essential oil (PEO) at 10, 12, 14, and 20% and coated with 1% chitosan (CH) were used for the elaboration of nets, which were evaluated on C. gloeosporioides and Rhizopus stolonifer on nutrient media and fruit and on the ripening behavior of Hass avocados at ambient temperature. The spore germination stage of C. gloeosporioides was the most extensively damaged (78% inhibition). The incidence of anthracnose was notably reduced by almost 80% in the avocados stored in the 60/40 PLA/PBAT nets coated with 1% CH. The overall values regarding weight loss, °Brix, and dry matter were c.a. 23.5%, 7.5, and 24.5%, respectively. The changes in firmness, color, and CO2 production were particularly associated with the initial harvest index and storage temperature rather than with the nets. In future research, essays on nets should include evaluations at the commercial levels.

Effect of Additional Cellulose Bacterial from Nata De Soya and Chitosan in Bioplastic Manufacturing

Plastics are synthetic polymers from petroleum or petrochemicals that are difficult to biodegrade by bacteria and microbes. Non-biodegradable plastics cause the accumulation of large amounts of plastic waste Solutions that can reduce plastic waste by making plastics that are easily biodegradable. In this study, tofu liquid waste is used as a basic material for the manufacture of bioplastics. Tofu liquid waste is waste generated from tofu production. This study aims to determine the effect of adding bacterial cellulose and chitosan on the manufacture of bioplastics from liquid waste tofu (whey) in terms of tensile strength, elongation, water solubility, and functional groups (FTIR) in accordance with PET plastic standards (Polyethylene terephthalate). The research procedure on the effect of adding bacterial cellulose and chitosan on the bioplastic fabrication of Nata De Soya. First, from tofu liquid waste, Acetobacter Xylinum starter was added and then fermented for 10-12 days to become Nata De Soya. After that it was neutralized with aquadest, removed the water by pressing, and dried to become bacterial cellulose. The process of making bioplastic with the addition of chitosan (grams) 2,3; 3.1; 3.9; 4.7 and 5.5 and bacterial cellulose (grams) 0.5 ;1.5; 3.9; 7; and 11. In the manufacture of bioplastics with the addition of Bacterial Cellulose and chitosan, it is appropriate, namely the tensile strength obtained will increase and the solubility in water decreases. From the results of our research, the best results were obtained in the addition of S5K5 with a tensile strength value of 9.665 MPa, an elongation value of 31.3%, and a solubility value in water of 17.9%. It has a higher tensile strength, smaller elongation and lower water solubility. The effect of the addition of chitosan on the tensile strength value can increase the tensile strength (Tensile Strength Value), the addition of bacterial bacterial cellulose and chitosan can affect the elongation of bioplastics getting smaller and the effect of chitosan can reduce solubility in water. It is good but still far from the standard PET (Polyethylene Terefelat) which is 60-80 Mpa.

Soil-biodegradable mulch is an alternative to non-biodegradable plastic mulches in a strawberry-lettuce double-cropping system

Double-cropping strawberry (Fragaria × ananassa Duch.) and lettuce (Lactuca sativa L.) could be a sustainable alternative practice for diversified specialty crop growers. Plastic mulch is beneficial for strawberry and lettuce production with soil-biodegradable mulch (BDM) providing opportunities to reduce plastic waste generation and costs of mulch disposal. The objective of this study was to compare non-biodegradable plastic mulches and BDM to bare ground cultivation in a strawberry–lettuce double-cropping system in a Mediterranean climate. A split-plot randomized complete block design experiment with mulch treatment [non-biodegradable polyethylene (PE) film, “weedmat” (woven, PE-based), BDM, and bare ground control] as the main factor and double-cropping rotation scheme (rotation 1 or 2) as the split-plot factor was conducted between 2020 and 2021. Strawberry yield was overall greatest when mulched with BDM, PE, and weedmat compared to the bare ground control. Total soluble solids (TSS), pH, and total titratable acidity (TA) of strawberry differed due to harvest date, but only pH differed due to mulch treatment. For lettuce canopy cover, rotation 2 had greater canopy cover (86%) compared with rotation 1 (66%) 30 days after transplanting. Average head weight (0.4 kg) and head length and diameter (both 20 cm) did not differ due to mulch or rotation. Average soil temperatures under PE and BDM were ~1.5°C higher than under weedmat and 2.5°C higher than the bare ground control. Soil under weedmat had the highest moisture content, whereas the PE, BDM, and bare ground treatments had similar levels. PE, BDM, and weedmat provided equivalent weed suppression, whereas the bare ground control had the most weeds. BDM deterioration estimated as percent soil exposure (PSE) was greatest (59% PSE) by the end of the experiment, whereas PE had 18% PSE and weedmat had no deterioration. Results show that despite high levels of deterioration, BDM performs similarly to PE in terms of soil temperature and moisture modification, weed suppression, and promotion of crop growth and yield in a double-cropped system. Double-cropping strawberry and lettuce is a promising alternative for growers to diversify their crop type and with potential economic benefits by increasing mulch lifespan.

Reactive melt crosslinking of cellulose nanocrystals/poly(ε-caprolactone) for heat-shrinkable network

Focusing on the challenge of non-biodegradable plastics replacement, we propose a design for peroxide-initiated crosslinking of biodegradable poly(ε-caprolactone) (PCL) and renewable cellulose nanocrystals (CNCs) bionanocomposites. An industrially scalable water-assisted reactive melt-processing (REx) is studied to explore the hypothesis of synergy between simultaneous effects of water on improving CNC dispersion and boosting PCL branching/crosslinking. We demonstrate that the melt processing control enables the preparation of targeted thermoplastic/thermoset bionanocomposites with gel content up to ≈ 40 %, identified as the limit of their melt-processability. Structural characterization reveals that ≈ 70 wt% of the initial CNC content is irreversibly incorporated in a percolating network, enhancing the crosslinked bionanocomposites properties. The bionanocomposites' complex viscosity and elastic character increase with the gel content, thus improving PCL melt performance. Furthermore, the irreversible entrapment of CNCs in the 3D percolating network provides heat-shrinkability, indicating a potential of the reacted bionanocomposites for heat-triggered shape-memory.

Food Packaging Materials with Special Reference to Biopolymers-Properties and Applications

Food is an important material for survival. The increasing world population, urbanization, and globalization are responsible for more food. This has increased challenges in food storage and safety. Therefore, it is necessary to preserve food by suitable packaging materials. The packaging materials are useful for giving longer life to the food and improving quality during transportation, storage and distribution. Innovations and developments in food packaging, have become very important in the food industry. Variety of packaging materials such as plastics, paper, metal, and glass are used in food packaging. Most widely used packaging materials are non-biodegradable plastics but these are harmful to environment and human health. Therefore, the food industry is in search of environment friendly replacement of non-biodegradable plastics by biodegradable plastics. However, no systematic literature is available on the subject, so there is a need to summarise the available information in a systematic way. Polymer packaging materials with special reference to biodegradable plastics have been discussed in detail. Different type of biodegradable plastics with their functionality and applications in food packaging have been summarised. Literature available has shown that biodegradable plastics are much better for food packaging as compared to other packaging materials. Increasing fundamental research in the use of biodegradable polymers in food packaging and effort to protect the environment, requires deep understanding and there are lot of challenges for commercialization, which are to be tackled. All these aspects have been discussed in this review article.

Production of High Yield Pulp and Paper from Jute Fibre in Bangladesh: A Comparison with Other Crop Residues

As the allocated forestland for pulp and paper production in Bangladesh is very limited and a substantial amount of crops residues are generated each year, the latter can substitute for pulp and paper production. In this context, eight residues of crops produced in Bangladesh were evaluated. Final pulp yields were 40 -65% with the kappa number of 11-32% depending on crops residues. The experimental processes are outlined. The physico-mechanical properties of handmade papers are estimated by standard procedure. Gram per Square Metre (GSM), brightness percentage, thickness and tearing strength of different handmade paper sheets shows acceptable papermaking properties. FT-IR analysis were carried out for identifying types of chemicals bonds (functional groups).The study indicates that these hand-made papers can be used for making eco-friendly paper bags, packaging material which will be suitable alternative to the non-biodegradable plastic, a cause of ecological and environmental pollution.

An Environmentally Friendly Solution for Waste Facial Masks Recycled in Construction Materials

In response to the COVID-19 pandemic, single-use disposable masks saw a dramatic rise in production. Facial masks that are not properly disposed of will expose the environment to a form of non-biodegradable plastic waste that will take hundreds of years to degrade. Therefore, recycling such waste in an eco-friendly manner is imperative. Fibered or shredded waste masks can be used to make green concrete that is an environmentally friendly solution to dispose the facial masks. This study prepared six classes of concrete samples, three of which contained fibers from masks and three of which contained shredded masks at the ages of seven days and 28 days. The results show that in the seven-day and 28-day samples, mask fiber added to the mixes resulted in increased compressive strength. For seven-day and 28-day samples, the compressive strength increased by 7.2% and 10%, respectively. Despite that, the results of the shredded mask addition to concrete indicate that the increase in shredded mask volume has a minor impact on the compressive strength of the seven-day samples. An increase in shredded mask from 0.75 to 1% increased 28-day compressive strength by 14%. However, the compressive strength of the mask fiber decreased by 8 after 1% volume. According to a thermal analysis of 28-day concrete samples, as the fiber percentage increases, the mass loss percentage increases. The mass loss rate for samples containing fibers is higher than that for samples containing shredded mask pieces. In general, based on the results mentioned above, the use of fiber in concrete in its fiber state enhances its strength properties. As a result, using shredded mask pieces in concrete leads to better curing due to the reduction of residual capillary pore water loss in construction materials.