Negative Voltage Polarity Research Articles

Diagnostics of porcelain insulators by partial discharges characteristics

RELEVANCE of the research is in the development of a non-destructive method for diagnosing porcelain insulators of high-voltage electrical equipment based on analysis of the characteristics of partial discharges (PDs). The problem of the final stage of breakdown of both the discharge gap and porcelain insulators recognizing is currently has not solved. THE PURPOSE. Recognition of PDs in solid insulation, study of PDs characteristics in a pre- breakdown situation, recognition of defective insulators based on PDs characteristics analysing. METHODS. The study of PDs characteristics for a defective and functional porcelain insulator were carried out. To study the characteristics of various types of PDs, including in the pre-breakdown situation, a system of surface-needle electrode system was used. RESULTS. The article describes compares the PDs characteristics obtained using standard R-400 device and a digital storage oscilloscope (DSO) using a telescopic antenna. A technique for recognizing the development of the pre-breakdown situation of the surface-needle discharge gap and the porcelain insulator was developed. The technique for recognizing a defective porcelain insulator from the amplitude-phase diagrams (APD) of PDs was developed. The method for assessing the breakdown voltage of porcelain insulators based on the characteristics of partial discharges was developed. CONCLUSION. At the moment of transition to the pre-breakdown stage were observed a sharp increase in the counter-movement of charges of opposite polarity. In the stage immediately before the breakdown, near zero values of the applied voltage of negative polarity, ordered PDs of the same polarity as the applied voltage were recorded in large numbers. These discharges led to an increase in leakage current and were interpreted as initial corona discharges. These discharges were recorded both by a telescopic antenna in a surface-needle system and in porcelain insulators.

Evolution from a guided-streamer mode to a continuous-discharge mode in an atmospheric pressure argon plasma jet

Atmospheric pressure plasma jet (APPJ) has attracted much attention due to its versatile applications in various fields, which normally operates in either a guided-streamer mode or a continuous-discharge mode. In this paper, temporal evolution is observed from the guided-streamer mode to the continuous-discharge one in an argon APPJ excited by a sinusoidal voltage. Waveforms of voltage and current indicate that the voltage applied to the electrode is distorted severely from the ideal sine. For the guided-streamer mode, there is only one discharge pulse per half voltage cycle. For the mode transition or the continuous-discharge mode, there is only one discharge composed of a pulse and a hump per half voltage cycle. Fast photography implemented for the mode transition reveals that both the discharges in the positive and the negative voltage polarities evolve from the guided-streamer mode to the continuous-discharge one. In the guided-streamer mode of the mode transition, the discharge behaves as a positive streamer in the positive voltage polarity, while a negative streamer in the negative voltage polarity. In addition, the mode transition only occurs in a range of dissipated power and gap width. Based on optical emission spectroscopy, temporal evolutions of the mode transition are investigated for excited electron temperature, electron density, and field strength. Moreover, their spatial distributions along the argon stream are studied at different time instants. These results are of great importance for the discharge dynamics of APPJ.

Studying of Filamentation Mechanism for Nanosecond Surface Dielectric Barrier Discharge. Part 1. Local Field Approximation

The goal of this work is to check numerically whether or not the previously proposed mechanism for surface barrier discharge filamentation in nitrogen in the case of positive polarity nanosecond voltage pulse is applicable for similar process in nitrogen and air in the case of negative voltage polarity pulse. The results have shown, that in this case some signs of successful filamentation modeling are present both in nitrogen and air, but the whole dynamics of discharge development is qualitatively different from that one observed in experiment. It is assumed, that the failure of simulation is due to the usage of local field approximation, which is too rough inside a region with steep electron density gradient relevant to filamentation zone.

Partial discharge characteristics of peek utilized in press-pack IGBT under DC voltage

Modular multilevel converters (MMCs) have been utilized in solid-state transformers (SSTs). With the increasing demand in high-voltage power module in MMC-SST, press-pack IGBTs are very promising. The poly-ether-ether-ketone (PEEK) frame is utilized in the submodules of press-pack IGBT to withstand the high voltage. The electric field simulation in this paper reveals that electric field concentrates on the surface of the PEEK frame. Thus, the surface partial discharge characteristics under direct current (DC) voltage is investigated by the developed test bench. The results show that surface partial discharge model of PEEK sample has polarity effect. Under positive and negative polarity voltage, the average discharge quantity, maximum discharge quantity and discharge repetition rate of the PEEK sample all increase with the voltage amplitude. Moreover, the front time of the surface partial discharge waveform reaches 20 ns, and its frequency spectrum is concentrated in range of 10–20 MHz.

Use of Plat-Bar Electrode Media to Detect Partial Discharge in Epoxy Resin Materials on PCB Surfaces

The electric power system must have a protection system with reliable electric power isolation, so that the supply of electrical energy works properly and optimally. There are several kinds of disturbances in the electric power distribution system, one of which is a partial discharge. This study aims to investigate the effect of plate-rod electrodes on partial discharge, partial discharge voltage limits in solid insulation, and the characteristics of partial discharge in electrode media, and waveforms in partial discharge detection sensors. After conducting research, it was found that in the plate-rod type electrode media, the PDIV voltage appeared earlier than the plate-plate electrode media due to the cross-sectional area of the electrode media. And the limit of the pre-discharge voltage of PCB type solid insulation on the plate-bar electrodes is at a voltage of 1.3 kV. Several indicators to determine the characteristics of the partial discharge are background noise off (BGN off), background noise on (BGN on), partial discharge inception voltage (PDIV), and partial discharge voltage. After being examined, the value of each partial discharge detection voltage was obtained at negative and positive polarity voltages on the electrode plates and plate needles respectively 2.85 kV, 2.95 kV and 1.32 kV, 1.57 kV.

Simultaneous hydrodynamic cavitation and nanosecond pulse discharge plasma enhanced by oxygen injection

A novel Hydrodynamic Cavitation-Assisted Oxygen Plasma (HCAOP) process, which employs a venturi tube and oxygen injection, has been developed for enhancing the production and utilization of hydroxyl radicals (·OH) in the degradation of organic pollutants. This study has systematically investigated the fluid characteristics and discharge properties of the gas–liquid two-phase body in the venturi tube. The hydraulic cavitation two-phase body discharge is initiated by the bridging of the cavitation cloud between the electrodes. The discharge mode transitions from diffuse to spark to corona as the oxygen flow rate increases. The spark discharge has the highest current and discharge energy. Excessive oxygen results in the change of the flow from bubbly to annular and a subsequent decrease in discharge energy. The effects of cavitation intensity, oxygen flow rate, and power polarity on discharge characteristics and ·OH production were evaluated using terephthalic acid as a fluorescent probe. It was found that injecting 3 standard liter per minute (SLPM) of oxygen increased the ·OH yield by 6 times with only 1.2 times increase in power, whereas<0.5 SLPM of oxygen did not improve the ·OH yield due to lower breakdown voltage. Negative polarity voltage increased the breakdown voltage and ·OH yield due to asymmetric density and pressure distribution in the throat tube. This polarity effect was explained by numerical simulation. Using indigo carmine (E132) as a model pollutant, the HCAOP process degraded 20 mg/L of dye in 5 L water within 2 min following a first-order reaction. The lowest electric energy per order (EEO) was 0.26 (kWh/m3/order). The HCAOP process is a highly efficient flow-type advanced oxidation process with potential industrial applications.

The device for monitoring the insulation breakdown zone of power cable lines in distribution networks with isolated neutral system during high-voltage diagnostic

The article considers an electrical device designed for diagnostic work in distribution networks of 6-10 kV, namely, the determination of damage zones in case of failure of insulating materials of cable lines during high-voltage diagnostics with a rectified voltage of negative polarity. The novelty of the developed device is its ability to connect directly to a high-voltage cable line without additional matching devices. The device is capable of detecting damage zones in lines up to 10 km remotely with an error of up to 0.2% of the cable length. The prefix allows you to fix any variants of damage to single-phase and three-phase cable lines with high transient resistance at the site of damage without the operation of “burning” insulation, which significantly reduces the time of repair work at the controlled facility.

Creation of a library of images of cable line insulation breakdown for neural network training based on data from the study of wave processes in the digital twin of the cable line

The aim of the work is to create a library of images of cable line insulation breakdown for training a neural network of a functional unit integrated into a high voltage test facility based on data from the study of wave processes in the digital twin of a cable line. The goal is achieved by determining the characteristic properties of the wave process in a cable line when tested with high direct voltage of negative polarity during field experiments and verifying these results on a mathematical model. The calculated data array on the verified model is the main volume of primary information for creating a library of images of insulation breakdown. The most important and significant results are the creation of a library of images of insulation breakdown and the adaptation of the algorithm for approximating input data with images from the neural network library, the integration of artificial intelligence into the process of determining the location of defective insulation at the test stage. The significance of the results is to reduce the methodological and instrumental error in determining the damage zone, since all stages of data collection and analysis are performed by a functional module built into the test unit, in addition, the calculation is performed automatically, which minimizes the role of anthropogenic factors on the result and reduces the requirements for the personnel of the electrical laboratory, the introduction of such equipment will reduce complete the time of elimination of the accident and increase the speed of restoration work on the route of the line.

Compression of a Beam of Fast Argon Atoms for Surface Polishing

The results of studying a beam source of fast argon atoms obtained by neutralizing charges of accelerated ions during their flight through an accelerating grid in the form of a set of plane–parallel plates are presented. Ions are accelerated from the plasma emitter by a voltage of negative polarity at the grid, fly into the gaps between its plates, and, when approaching their surfaces, cause the emission of electrons that neutralize the ion charge. The equivalent beam current of fast atoms emitted from the grid is up to 90% of the current in its circuit, and their energy is equal to the ion energy that corresponds to the accelerating voltage between the plasma emitter and the grid. To increase the beam current density of fast atoms on the treated surface, the sections of the grid plates facing the plasma emitter are made in the form of a segment of a circle. The movement of ions and fast atoms that are formed inside the grid to the center of this circle makes it possible to reduce the beam width by an order of magnitude and increase the flow density of fast atoms without reducing the angle of their incidence on the treated surface. The beam compression significantly improves the efficiency of polishing a surface with a beam of fast neutral argon atoms with an angle of incidence on the surface of 80°.

Electrical Breakdown of Oil-Impregnated Pressboard under AC and DC Voltages Ramp

In this work, we present an experimental study on electrical breakdown, also called dielectric failure on a material widely used as insulation in oil transformers and other equipment. This material is pressboard paper impregnated with insulating oil. The breakdown tests are carried out under three types of voltage and for several voltage rise speeds. Dielectric breakdown is a random phenomenon, many tests are carried out on a large number of samples and the results obtained have been subjected to statistical processing. The material is cut into square plates of 7.5 cm in length from a set of plates 2 m² in length and 500 µm in thickness. Prior to the tests, the samples were conditioned in a desiccator with silicone gel for at least 24 hours in order to eliminate any presence of moisture. Then they were impregnated with Borak22 insulating oil for at least one week. The tests consist of placing the sample concerned between two cylindrical bronze electrodes and applying a voltage ramp at constant speed until breakdown. After failure, the value of the breakdown voltage is taken. These tests are carried out in the laboratory at room temperature. However, we have tried to reproduce the same conditions for all the tests. These various tests relate to the effect of the form and the rate of rise of the applied voltage on the dielectric strength of the pressboard paper impregnated with Borak22 insulating oil. Two measuring devices were used, and the tests were carried out under three voltage forms: sinusoidal alternating current, continuous positive polarity, and continuous negative polarity, and at eight different voltage ramp speeds: 0,69; 1,07; 1,4; 1,89; 2,38; 2,94; 3,28 and 4,17 kV/s. For each measurement point, 35 samples of pressboard paper are used and tested. A total of 840 results were obtained and processed using the two-parameter Weibull statistical model. In order to validate this model, these results are subjected to a Kolmogorov-Smirnov adequacy test and are framed by 95% confidence bands. The maximum likelihood method is used for the estimation of the Weibull parameters and the smoothing of the experimental points. The results of the statistical tests on the breakdown voltage measurement points obtained confirm the use of the two-parameter Weibull model. The evolution of the nominal breakdown voltage as a function of the voltage ramp of the three forms of applied voltage gives three properties of the same form, which is akin to the letter 'S'. The breakdown voltage first increases linearly for low speeds, then increases and takes an exponential form for medium speeds, then tends towards a certain saturation for high speeds. The breakdown voltage under the DC voltage ramp is higher than the voltage obtained for the AC voltage ramp and are higher under negative polarity voltage than those under positive polarity voltage.

Influence of Space Charge on Dielectric Property and Breakdown Strength of Polypropylene Dielectrics under Strong Electric Field

Space charge accumulation in polypropylene (PP) affect the dielectric properties and breakdown strength of the material. The pre-injected charge in PP under the action of different polarity voltage is quantitatively characterized, and the effects of the pre-injected charge inside the dielectric on the dielectric properties and breakdown strength are measured and analyzed. Based on the molecular simulations, the influence mechanism of the temperature on dielectric properties and breakdown are discussed. The experimental results show that the injected charges in PP under the negative polarity voltage is significantly larger than that of the positive polarity. These charges have a great influence on the dielectric constant and breakdown performance of PP, and the effect is different for different charge polarity. The effect of negative polarity pre-voltage conditions on the dielectric constant is much greater than that of positive polarity, and the dielectric constant of PP decreases from 2.2 to 1.3, decreasing about 41% under the negative polarity pre-voltage. By contrast, the dielectric constant slightly increases under the effect of the homopolar preload. Furthermore, the breakdown strength of the dielectric after the heteropolar preload is 249 kV/mm, which is 36% lower than that of PP without pre-voltage, and it slightly increases after the positive polarity pre-voltage. As the temperature increases, the increase in free volume favors the development of electron collision ionization and electron collapse processes, leading to a decrease in breakdown voltage at high temperatures. This work has a good guiding significance for the comprehensive evaluation of energy storage parameters.

Influence of Temperature on Lightning Performance of Mineral Oil

This article deals with the influence of temperature on the lightning impulse breakdown voltage (LI BDV) of mineral oil in a non-uniform electric field. The experiments were performed in point–plane electrode arrangements under a standard lightning impulse voltage of negative polarity. The LI BDV for the temperatures of 20, 40, 60, 80, 100 and 110 °C was measured using a step method with registration of the light signals emitted during pre-breakdown and breakdown phases. The average propagation velocity was also determined. The results confirm that the mineral oil tested under LI voltage behaves similarly to AC voltage-based stress. The LI BDV increases with temperature up to 100 °C and then tends to decrease. The results demonstrated that viscosity dependent processes are responsible for increasing the LI BDV with temperature up to the 100 °C; and liquid vapor formation processes are responsible for decreasing the LI BDV at temperatures equal to and higher than 100 °C.

Atmospheric plasma-based approaches for the degradation of dimethyl phthalate (DMP) in water

Cold plasma based treatment of contaminated water is becoming a promising novel green remediation option. This study assessed the performance of two different cold plasma reactors, using, respectively, a self-pulsing discharge (SPD) and a multipin corona discharge (MCD), in the degradation of dimethyl phthalate (DMP), a persistent and ubiquitous pollutant of the aquatic environment. The process kinetics and energy efficiency, as well as the main plasma generated reactive species were determined under various operating conditions concerning the plasma feed gas and flowrate, the voltage polarity, the input power, the DMP initial concentration, the liquid conductivity, and the aqueous matrix used to prepare DMP solutions for these experiments. The MCD reactor, operated with air as plasma feed gas and negative voltage polarity, gave the best results in terms of rate and energy efficiency. Moreover, variations in plasma input power and in the liquid conductivity have limited effect on DMP degradation rate, making this reactor suitable for treating liquids with a range of initial conductivities The effects of DMP initial concentration on its rate of degradation and on the process energy efficiency were also investigated. Differences in the efficiency of production and distribution of plasma generated reactive species, notably •OH and H2O2, observed for the two tested reactors are discussed in terms of different extension of the plasma/liquid interface and diffusion into the bulk solution. It is proposed that among the reactive species, •OH foremost, and O3 to a lesser extent, play a pivotal role in DMP degradation, while the contribution of H2O2 appears to be limited. The rate of DMP degradation was not drastically different in Milli-Q water and in tap water, a positive outcome in view of practical applications of the technology. The lower rate observed in tap than in Milli-Q water is attributed to the presence of bicarbonate and carbonate, which are known scavengers of hydroxyl radicals.

Surface Potential Driven Water Harvesting from Fog.

Access to clean water is a global challenge, and fog collectors are a promising solution. Polycarbonate (PC) fibers have been used in fog collectors but with limited efficiency. In this study, we show that controlling voltage polarity and humidity during the electrospinning of PC fibers improves their surface properties for water collection capability. We experimentally measured the effect of both the surface morphology and the chemistry of PC fiber on their surface potential and mechanical properties in relation to the water collection efficiency from fog. PC fibers produced at high humidity and with negative voltage polarity show a superior water collection rate combined with the highest tensile strength. We proved that electric potential on surface and morphology are crucial, as often designed by nature, for enhancing the water collection capabilities via the single-step production of fibers without any postprocessing needs.

Implementation and design of an interleaved Cuk converter with selective input current ripple elimination capability

SummaryNowadays, buck–boost DC–DC converters are widely used in numerous power devices. However, to have a suitable buck–boost DC–DC converter, reducing the input current ripple seems to be necessary. Also, having a lower current ripple at the converter output allows using low‐cost, long‐life ceramic capacitors instead of electrolytic capacitors. The presented buck–boost converter is made by interleaving two Cuk converters with positive and negative output voltage polarity, which provides the chance to eliminate the input current ripple at the selective duty cycle. The selective duty ratio can be determined by designing the inductors amounts at the input side of both converters. Though a new combination for the buck–boost converter is presented, which has zero input current ripple and low output current ripple which is obtained by output inductors. The converter maximum voltage gain is 2D/1‐D and has easy control. In conclusion, a prototype model with 100‐W output power is implemented, and the theoretical analysis and laboratory results are compared and validated.

Impulsive Breakdown of Mineral Oil and Natural and Synthetic Ester Liquids When Containing Varying Levels of Moisture

This article reports and discusses the results of impulse breakdown study of different insulating liquids under highly divergent electric field conditions. Samples of a natural ester (Envirotemp FR3), a synthetic ester (MIDEL 7131), and a naphthenic mineral oil (Shell Diala S4 ZX) at different levels of relative humidity were exposed to HV impulses with a nominal 7- $\mu \text{s}$ rise time and 150-kV peak voltage of both positive and negative polarity. A strong dependence of the breakdown voltage and time to breakdown of the investigated dielectric liquids was observed with respect to the polarity of the applied HV impulses. It was shown that the FR3 natural ester liquid has a higher dielectric strength when exposed to positive impulse than when under negative impulse stress. The opposite breakdown behavior was observed for the synthetic ester MIDEL 7131 and the naphthenic oil Shell Diala S4 ZX which exhibited lower breakdown voltage under positive energization as compared with the negative energization. The breakdown voltage and prebreakdown time obtained in the present tests of the naphthenic oil, Shell Diala S4 ZX, lie between that of the ester liquids irrespective of impulse polarity. It has been established that no statistically significant variations exist in the breakdown parameters (breakdown voltage and time to breakdown) of the studied dielectric liquids as their relative humidity is increased under either impulse polarity. The obtained results will help in coordination of practical applications of low environmental impact dielectric fluids in power and pulsed power systems and components.

Schemes of high-voltage rectifiers as part of dust removal electric gates

The problem of controlling emissions of dust fractions from various types of technological machines and containers during the production and transportation of bulk materials in the construction and metallurgical industries is quite urgent, due to the need to ensure environmental protection. The development of an energy efficient and inexpensive air filtration system can be an optimal solution to this problem. An important part of this system is the power supply. Measures aimed at increasing load characteristics of circuits of high-voltage rectifiers as a source of high DC voltage of negative polarity of dust collecting electric locks are considered in this work.

Numerical simulation of electrostatic field and its influence on submicron particle charging in small-sized charger for consideration of voltage polarity

In this paper, a pin-cylinder charger was employed to investigate the electrostatic field characteristic and its influence on submicron particle charging in positive and negative voltage polarity, respectively. The submicron particle's charging characteristics were also investigated thoroughly, including polarity, gas velocity, applied voltage, and injection position. Results showed that the increase of the applied voltage was proved a useful approach to enhance particle charging, especially for positive polarity. A 0.4 μm diameter particle achieved about a 60% increase from 5 kV to 8 kV. The negative polarity had advantages on particle charging, whose superiority could reach approximately 15% for 0.1 μm diameter particle in 8 kV voltage. The particle trajectory was a helpful bond to connect the particle charging with the electrostatic field, which decided the charging number and charging rate through the different distribution and intensity in two polarity conditions.

A Flying Capacitor-Based Multilevel Inverter Architecture With Symmetrical and Asymmetrical Configurations

In this article, a novel flying capacitor-based multilevel topology is presented to minimize the size and cost. The proposed topology can operate in the symmetrical and asymmetrical configuration of dc sources and produces the 9-level and 25-level output voltage, respectively. The minimized device count, negative polarity voltage generation without auxiliary H-bridge, reduced maximum peak inverse voltage across the switches, and inherent voltage balancing across the floating capacitors are the main advantages of the proposed topology. Two extended topologies are proposed, and various necessary parameters are derived from achieving a higher number of output voltage levels. The effective comparison is furnished in terms of switches, diodes, capacitors, total standing voltage, and cost function to show minimization of device count of the proposed topology against the recent popular topologies. The extensive simulations in MATLAB <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\backslash $ </tex-math></inline-formula> Simulink are carried out to study the operation of proposed topology and feasibility is validated through the laboratory experimental tests. The performance of the topology under dynamical variation of frequencies, modulation indexes, and load are studied and respective results are presented.

Surface potential and roughness controlled cell adhesion and collagen formation in electrospun PCL fibers for bone regeneration

Surface potential of biomaterials is a key factor regulating cell responses, driving their adhesion and signaling in tissue regeneration. In this study we compared the surface and zeta potential of smooth and porous electrospun polycaprolactone (PCL) fibers, as well as PCL films, to evaluate their significance in bone regeneration. The ’ surface potential of the fibers was controlled by applying positive and negative voltage polarities during the electrospinning. The surface properties of the different PCL fibers and films were measured using X-ray photoelectron spectroscopy (XPS) and Kelvin probe force microscopy (KPFM), and the zeta potential was measured using the electrokinetic technique. The effect of surface potential on the morphology of bone cells was examined using advanced microcopy, including 3D reconstruction based on a scanning electron microscope with a focused ion beam (FIB-SEM). Initial cell adhesion and collagen formation were studied using fluorescence microscopy and Sirius Red assay respectively, while calcium mineralization was confirmed with energy-dispersive x-ray (EDX) and Alzarin Red staining. These studies revealed that cell adhesion is driven by both the surface potential and morphology of PCL fibers. Furthermore, the ability to tune the surface potential of electrospun PCL scaffolds provides an essential electrostatic handle to enhance cell-material interaction and cellular activity, leading to controllable morphological changes.