Need For Underfill Research Articles

Understanding Mold Compound Behavior on Flip Chip QFN Packages

Abstract Overmolded Flip Chip Quad Flat No-lead (FCQFN) is a low cost flip chip on leadframe package where there is no need for underfill, and is compatible with Pb free or high Pb metallurgy. A robust leadframe design, quality solder joint formation and an excellent molding process are three factors needed to assemble a high performance FCQFN. It combines the best of both wirebonded QFN and wafer chip scale devices. For example, wafer chip scale has low resistance, but inadequate thermal performance (due to absence of thermal pad), whereas wirebonded QFN has good thermal performance (i.e., heat dissipated through conductive die attach material, through the pad and to the board) but higher resistance. Flip chip QFN combines both positive aspects – that is: low resistance and good thermals. One of the common defects for molded packages across the semiconductor industry is the occurrence of mold voiding as this can potentially affect the performance of a device. This paper will discuss how mold voiding is mitigated by understanding the mold compound behavior on flip chip QFN packages. Taking for example the turbulent mold flow observed on flip chip QFN causing mold voids. Mold compound material itself has a great contribution to mold voids, hence defining the correct attributes of the mold compound is critical. Altering the mold compound property to decrease the mold compound rheology is a key factor. This dynamic interaction between mold compound and flip chip QFN package configuration is the basis for a series of design of experiments using a full factorial matrix. Key investigation points are establishing balance in mold compound chemistry allowing flow between bump pitch, as well as the mold compound rheology, where gelation time has to be properly computed to allow flow across the leadframe. Understanding the flow-ability of mold compound for FCQFN, the speed of flow was optimized to check on its impact on mold voids. Mold airflow optimization is also needed to help fill in tighter bump spacing but vacuum-on time needs to be optimized as well.

Flexible Electronics: Thin Silicon Die on Flexible Substrates

<para xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> Silicon thinned to 50 <formula formulatype="inline"><tex Notation="TeX">$\mu{\hbox {m}}$</tex></formula> and less is flexible allowing the fabrication of flexible and conformable electronics. Two techniques have been developed to achieve this goal using thinned die: die flip chip bonded onto flexible substrates [polyimide and liquid crystal polymer (LCP)] and die flip chip laminated onto LCP films. A key to achieving each of these techniques is the thinning of die to a thickness of 50 <formula formulatype="inline"><tex Notation="TeX">$\mu{\hbox {m}}$</tex></formula> or thinner. Conventional grinding and polishing can be used to thin to 50 <formula formulatype="inline"><tex Notation="TeX">$\mu{\hbox {m}}$</tex></formula>. At 50 <formula formulatype="inline"><tex Notation="TeX">$\mu{\hbox {m}}$</tex></formula>, the active die becomes flexible and must be handled by temporarily bonding it to a holder die for assembly. Both reflow solder and thermocompression assembly methods are used. In the case of solder assembly, underfill is used to reinforce the solder joints. With thermocompression bonding of the die to an LCP substrate, the LCP adheres to the die surface, eliminating the need for underfill. </para>

Assembly of Copper Column Interconnect Flip Chip

This paper addresses a new flip chip interconnection technology, flexible flip chip connection (F2C2) technology, for attaching silicon chips to a chip carrier using flexible copper wires. F2C2 is a novel approach to create area array flip chip interconnections using a matrix block of wires encapsulated with a heat-resistant, dissolvable substance. A slice from the wire matrix ingot is first attached to the chip using solder. The other end of the slice is then matched and soldered to the footprint of a substrate. Finally, the encapsulating, dissolvable substance is removed from the body of the slice, leaving the chip attached to the carrier by the inter- disposed, flexible copper wires. The compliant copper wire interconnections can accommodate the coefficient of thermal expansion (CTE) mismatch problem between die and substrate, thus eliminating the need for underfill.

Sea of leads (SoL) ultrahigh density wafer-level chip input/output interconnections for gigascale integration (GSI)

Sea of Leads (SoL) is an ultrahigh density (>10/sup 4//cm/sup 2/) compliant chip input/output (I/O) interconnection technology. SoL is fabricated at the wafer level to extend the economic benefits of semiconductor front-end and back-end wafer-level batch fabrication to include chip I/O interconnections, packaging, and wafer-level testing and burn-in. This paper discusses the fabrication, the mechanical and electrical performance, and the benefits of SoL. SoL can lead to enhancements in reliability, electrical performance, manufacturing throughput, and cost. A chip with 12 /spl times/ 10/sup 3//cm/sup 2/ compliant I/O leads is demonstrated. The mechanically compliant I/O leads are designed to enable wafer-level testing and eliminate the need for underfill between chips and printed wiring boards by mitigating thermo-mechanical expansion mismatches between the two. The fabrication of partially nonadherent, or slippery, leads is desirable as it allows the leads to freely undergo strain during thermal cycling. Compared to adherent metal leads, preliminary results show that slippery leads enhance the overall in-plane compliance. Microindentation experiments show that a polymer film with embedded air gaps provides substantially higher compliance than a polymer film without embedded air gaps.

Materials characterization of the effect of mechanical bending on area array package interconnects

The mechanical integrity of solder joint interconnects in PWB assemblies with micro-BGA, chip scale, and land grid array packages is being questioned as the size and pitch decrease. Some consumer products manufacturers have mechanically reinforced fine pitch package interconnects with an adhesive underfill, and others are evaluating the need for underfill on a case-by-case basis. Three-point cyclic bend testing provides a useful tool for characterizing the expected mechanical cycling fatigue reliability of PWB assemblies. Cyclic bend testing is useful for characterizing bending issues in electronic assemblies such as repetitive keypad actuation in cell phone products. This paper presents the results of three-point bend testing of PWB assemblies with fine pitch packages. The solder joints on ceramic components performed better than a laminate interposer component in bend testing, because of the stiffening effect of the ceramic packaging materials. The methodology of materials analyses of the metallurgy of solder interconnects following mechanical bending and thermal cycle testing is described. The microstructure and fracture surfaces of solder joint failures in bend test samples differed significantly from thermal cycle test samples.