Multiplexing Signals Research Articles

Demonstration of High Capacity Bidirectional A-RoF System Using Wavelength Reuse and Frequency Multiplexing

We demonstrate a practical wavelength reuse bidirectional analog radio-over-fiber (A-RoF) system served by a single distributed feedback (DFB) laser. Frequency interleaving of downlink and uplink signals is proposed to ameliorate the spectral efficiency and mitigate the interference raised by the bidirectional transmission. Pre-emphasis is exploited to counteract the performance impairment brought about by the interaction between laser chirp and fiber chromatic dispersion. Through employing 64-QAM modulated 16 bands and 16-QAM modulated 12 bands filtered orthogonal frequency division multiplexing (f-OFDM) signals with 200 MHz bandwidth, asymmetric transmission with superior flexibility over 25 km fiber is attained, with an aggregate capacity of 20 Gb/s for downlink and 10 Gb/s for uplink. The mutual interference between the downlink and uplink is explored by overlapping the downlink and uplink signal spectra to varying degrees. Using the optimum frequency configuration, system performance is evaluated in terms of EVM and phase noise. To further investigate the effects caused by the Rayleigh backscattering and the stimulated Brillouin scattering (SBS), simulations are conducted on the proposed architecture, validating the conclusion from the experiment that the bidirectional transmission is primarily limited by the Rayleigh backscattering than the stimulated Brillouin scattering.

Photonics-Assisted Analog Wideband Self-Interference Cancellation for In-Band Full-Duplex MIMO Systems With Adaptive Digital Amplitude and Delay Pre-Matching

A photonics-assisted analog wideband RF self-interference (SI) cancellation and frequency downconversion approach for in-band full-duplex (IBFD) multiple-input multiple-output (MIMO) systems with adaptive digital amplitude and delay pre-matching is proposed based on a dual-parallel Mach–Zehnder modulator (DP-MZM). In each MIMO receiving antenna, the received signal, including different SI signals from different transmitting antennas and the signal of interest, is applied to one arm of the upper dual-drive Mach–Zehnder modulator (DD-MZM) of the DP-MZM, the reference signal is applied to the other arm of the upper DD-MZM, and the local oscillator signal is applied to one arm of the lower DD-MZM. The SI signals are canceled in the optical domain in the upper DD-MZM and the frequency downconversion is achieved after photodetection. To cancel the SI signals, the analog reference signal is constructed in the digital domain, while the amplitude and delay of the constructed reference are adjusted digitally by upsampling with high accuracy. Experiments are performed when two different SI signals are employed. The genetic algorithm or least squares algorithm is combined with segmented search respectively for the SI signal reconstruction and amplitude and delay pre-matching. A cancellation depth of around 20 dB is achieved for the 1-Gbaud 16 quadrature-amplitude modulation orthogonal frequency-division multiplexing signal.

Fiber-terahertz-fiber bridge system in the 355-GHz band using a simple optical frequency comb and a photonics-enabled receiver.

This Letter demonstrates a high-speed fiber-terahertz-fiber system in the 355-GHz band using stable optical frequency comb generation and a photonics-enabled receiver. At the transmitter, a single dual-drive Mach-Zehnder modulator is employed to generate a frequency comb by driving the modulator under an optimal condition. At the antenna site, a photonics-enabled receiver consisting of an optical local oscillator signal generator, a frequency doubler, and an electronic mixer is used to downconvert the terahertz-wave signal to the microwave band. Simple intensity modulation and a direct detection method are used for transmitting the downconverted signal to the receiver over the second fiber link. To demonstrate the proof of concept, we transmitted a 16-quadrature amplitude modulation (QAM) orthogonal frequency-division multiplexing signal over a system consisting of two radio-over-fiber links and a 4 m wireless link in the 355-GHz band and achieved a line rate of 60 Gb/s. We also successfully transmitted a 16-QAM subcarrier multiplexing single-carrier signal over the system and achieved a capacity of 50 Gb/s. The proposed system can facilitate the deployment of ultra-dense small cells in high-frequency bands in beyond-5G networks.

65,536-QAM OFDM signal transmission over a fiber-THz system at 320 GHz with delta-sigma modulation.

The transmission of a 65,536-ary quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM) signal supported by a hybrid fiber-terahertz (THz) multiple-input multiple-output (MIMO) system at 320 GHz is experimentally demonstrated in this Letter. We adopt the polarization division multiplexing (PDM) technique to double the spectral efficiency. Based on a 23-GBaud 16-QAM link, 2-bit delta-sigma modulation (DSM) quantization enables 65,536-QAM OFDM signal transmission over a 20-km standard single-mode fiber (SSMF) and a 3-m 2 × 2 MIMO wireless delivery, and satisfies the hard-decision forward error correction (HD-FEC) threshold of 3.8 × 10-3, corresponding to a net rate of 60.5 Gbit/s for THz-over-fiber transport. Meanwhile, below the fronthaul error vector magnitude (EVM) threshold of 0.34%, a maximum signal-to-noise ratio (SNR) of 52.6 dB is achieved. To the best of our knowledge, this is the highest modulation order achievable for DSM applications in THz communication.

Single-Input Broadband Hybrid Doherty Power Amplifiers Design Relying on a Phase Sliding-Mode of the Load Modulation Scheme

This work introduces a novel design theory for a single-input hybrid Doherty power amplifier (PA) inspired by the design space existing within the previously reported dual-input Doherty–Chireix (outphasing) continuum. Unlike the conventional <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\lambda /4$ </tex-math></inline-formula> Doherty PA inverter which only performs the correct load modulation at its center frequency, the hybrid Doherty PA (HD <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\omega $ </tex-math></inline-formula> -PA) combiner network achieves a wideband load modulation using the frequency dependence of the electrical length of the output combiner lines versus frequency for sliding the PA mode of operation. A modified theory is presented in this work to allow for a single-input PA implementation. In this new design, the outphasing angle is only changing with frequency and not the input power. A transmission line phase shifter is used to provide the correct frequency-dependent input phase offset ensuring the correct wideband load modulation performed by the output combiner. A novel methodology is also proposed to select the optimal input phase offset to reduce the variation in the saturation power versus frequency and minimize the circuit size. A proof-of-concept demonstrator PA circuit is designed to operate from 2.5 to 3.3 GHz. When the fabricated PA is excited by a 20-MHz long-term evolution (LTE) modulated signal with 6-dB peak-to-average-power ratio (PAPR), an average efficiency of 45%–59% and adjacent channel leakage ratio (ACLR) less than −50 dBc are achieved after digital predistortion (DPD) across the entire band. When the fabricated PA is excited by a 5G-like 50-MHz orthogonal frequency-division multiplexing (OFDM) signal with 10-dB PAPR, an average efficiency of 33%–41% and ACLR less than −44 dBc are achieved after DPD across the entire band.

Channel estimation for OFDM-based indoor broadband power line communication systems

State-of-the-art indoor broadband power line communications (PLC) systems use orthogonal frequency division multiplexing (OFDM) signals with constellations up to 10 bits/symbol, which makes channel estimation a key aspect. This paper focuses on the initial channel estimation used in the payload, which might be further adapted by means of a decision-directed strategy. This initial estimate has to be computed on a per-frame basis and can be accomplished from the preamble, the header symbol (assuming that it has been correctly decoded) or from a combination of both. This work proposes simple channel estimation techniques for this problem and derives their most appropriate parameters. They are compared with the linear minimum mean squared-error (LMMSE) estimator and others commonly used in wireless scenarios by considering both their performance and computational complexity. The factors limiting the performance of the estimators based on the preamble and the header symbols are analyzed and the implications of the differences between PLC and wireless channels, such as the absence of fading, in the design of estimation techniques that require knowledge of the channel statistics are discussed. A performance analysis of the considered techniques is accomplished in a set of 171 measured indoor PLC channels. Obtained results indicate that estimators from the header perform better than those based on the preamble symbols and we provide a computationally simple estimator that gives nearly optimum performance by combining estimates from both the preamble and the header symbols.

Post-Processing of Iterative Estimation and Cancellation Scheme for Clipping Noise in OFDM Systems

Clipping is an efficient and simple method that can reduce the peak-to-average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals. However, clipping causes in-band distortion referred to as clipping noise. To resolve this problem, a novel iterative estimation and cancellation (IEC) scheme for clipping noise is one of the most popular schemes because it can significantly improve the performance of clipped OFDM systems. However, IEC exploits detected symbols at the receiver to estimate the clipping noise in principle and the detected symbols are not the sufficient statistic in terms of estimation theory. In this paper, we propose the post-processing technique of IEC, which fully exploits given sufficient statistic at the receiver and thus further enhances the performance of a clipped OFDM system as verified by simulations.

Transmission of Power and Signal Multiplex for Electric Vehicles Using Cascaded Multilevel Inverters

Abstract: P&amp;SMT, or power and signal multiplex transmission, is a method for transmitting communication signals using power electronic circuits. A three-phase cascaded multilevel inverter-based P&amp;S MT system is recommended in this investigation. By allowing communication signals to be transmitted without utilizing a Controller Area Network bus, the proposed solution can lower the wiring expense of the existing electric vehicle (EV) communication system. The system's architecture enables battery balancing discharge and motor speed management for EVs. In a simulation system proposed in MATLAB/Simulink, both power and communication signals are effectively conveyed using the combined pulse width modulation scheme and frequency shift keying approach. The maximum signal rate of the proposed system is established at 600 bits per second by analyzing the bit error rate of the sent signal.

A Channel Compensation Technique Based on Frequency-Hopping Binary Offset Carrier Modulated Signal

Space-Air-GroundIntegrated Network (SAGIN) has been becoming a promising future network construction to enable the integration of terrestrial communications, aerial networks and satellite systems, for achieving high data rate wireless access and seamless coverage. Focusing on the space-to-air propagation, which is requiring transmitted signal of large Doppler shift resilience in dynamic circumstances, the proposed signal as employing I/Q modulation to accommodate frequency-hopping binary offset carrier (FH-BOC) signal and orthogonal frequency division multiplexing (OFDM) signal, and to exploit respective benefits. Finally, numeric results are provided to demonstrate performance superiority on Bit Error Rate (BER) and signal tracking stability. In conclusion, our designed signal requires about 8 dB less energy per bit at the desired BER level than normally compensated OFDM signal.

Research and analysis of the efficiency fiber-optic communication lines using DWDM technologies

The performance indicators fiber-optic communication lines using spectral technology with separation communication channels are analyzed. The effectiveness of the use network resources optical telecommunication systems using spectral technologies based on the architectural concept of the next NGN (NGN, Next Generation Network) and future FN (FN, Future Network) networks has been studied. This work is devoted to the construction methods for calculating the indicators optical networks and the study methods and tools for improving the efficiency using network and channel resources fiber-optic communication lines using dense spectral multiplexing optical signals with separation communication channels. The problem ensuring effective management channel and network resources in optical communication networks are considered. As a result of the study technology spectral multiplexing, a new approach to the construction of a calculation method is proposed that describes the efficiency managing network and channel resources in fiber-optic communication lines, taking into account the numerous requirements their parameters and transfer characteristics. On the basis of the calculation method, analytical expressions are obtained that allow estimating the resources of the system, indicators informational and spectral efficiency of the functioning fiber-optic communication lines. The results of the research can be applied by cellular operators when designing an optical telecommunications network, in particular, to determine the optimal value of the capacity optical systems based on wavelength multiplexing technology and modulation spectral efficiencies.

Digital radio-over-fiber system based on differential pulse code modulation and space division multiplexing.

In this paper, we present and experimentally demonstrate a digital-radio-over-fiber (D-RoF) architecture based on differential pulse code modulation (DPCM) and space division multiplexing (SDM). At low quantization resolution, DPCM can effectively reduce quantization noise and obtain significant signal-to-quantization noise ratio (SQNR) gain. We experimentally study the 7-core and 8-core multicore fiber transmission of 64-ary quadrature amplitude modulation (64QAM) orthogonal frequency division multiplexing (OFDM) signals with a bandwidth of 100 MHz in a fiber-wireless hybrid transmission link. Compared to PCM-based D-RoF, the error vector magnitude (EVM) performance in the DPCM-based D-RoF is effectively improved when the quantization bits (QBs) are 3-5 bits. In particular, when the QB is 3 bits, the EVM of the DPCM-based D-RoF is 6.5% and 7% lower than that of the PCM-based system in 7-core- and 8-core-multicore fiber-wireless hybrid transmission links, respectively.

Early-detection scheme based on sequential tests for low-latency communications

We propose an early-detection scheme to reduce communications latency based on sequential tests under finite blocklength regime for a fixed-rate transmission without any feedback channel. The proposed scheme processes observations sequentially to decide in favor of one of the candidate symbols. Such a process stops as soon as a decision rule is satisfied or waits for more samples under a given accuracy. We first provide the optimal achievable latency in additive white Gaussian noise channels for every channel code given a probability of block error. For example, for a rate R = 0.5 and a blocklength of 500 symbols, we show that only 63% of the symbol time is needed to reach an error rate equal to 10^{-5}. Then, we prove that if short messages can be transmitted in parallel Gaussian channels via a multi-carrier modulation, there exists an optimal low-latency strategy for every code. Next, we show how early detection can be effective with band-limited orthogonal frequency-division multiplexing signals while maintaining a given spectral efficiency by random coding or pre-coding random matrices. Finally, we show how the proposed early-detection scheme is effective in multi-hop systems.

Analysis of Bit Rate and Distance Variation on Multiplexing System of Indoor Li-Fi Technology Using Movable LED Panel

The major problem of using light fidelity (Li-Fi) technology is still limited to the line of sight (LOS) conditions, which poses a challenge to perform bandwidth efficiency to support increased bit rates, especially for indoor use. In addition, the distance between the lamp driver (transmitter) and the receiver becomes a critical discussion to determine the characteristics of propagation losses. Therefore, this study focuses on analyzing the performance of an indoor Li-Fi multiplexing system using a movable LED panel (LP) based on parameters of bit rate and distance variation on multiple-input multiple-output (MIMO) 2x2 and 4x4. The parameter analysis of signal quality included optical and electrical signal spectrum characteristics, signal-to-noise ratio (SNR), bit error rate (BER), and Q-factor parameters. Based on the results, the increase in bit rate and distance significantly increases the BER value and decreases the Q-factor value. Both the 2x2 and 4x4 mux systems can meet standards up to a bit rate of 30 Mbps at a LOS distance of 3 meters, while at a bit rate of 40 Mbps, there are no channels that meet the ITU-T standard. In addition, the quality of the signal received at a distance of 4 meters, the 2x2 mux system can only reach the standard at a bit rate of 20 Mbps for all channels. However, channel 3 and channel 4 on the 4x4 mux system model still have the BER and Q-factor values that meet the standard in the bit rate of 30 Mbps. However, the decrease in the SNR value affected by the bit rate increase and distance is insignificant. Therefore, it becomes an opportunity for further observation of the proposed multiplexing system, detection scheme, or responsivity, and signal processing on the receiver side to be reliable on the higher bit rate.

Pilot optimization for OFDM in the RSSB system

To increase the receiving sensitivity of the reversely single-sideband (RSSB) system with orthogonal frequency division multiplexing (OFDM) signal transmission, we use the improved pilot interval scheme and pilot power scheme in this system. The improved pilot interval scheme uses more pilots in areas where channel conditions are relatively good to avoid signal–signal beat interference (SSBI) issues for sub-carriers. The improved pilot power scheme compensates for frequency-selective fading by increasing the pilot power in areas where channel conditions are relatively poor. According to the simulation, the generated 60 GHz optical millimeter wave with 2.5 G bandwidth OFDM signal is delivered over 100 km standard single-mode fiber (SSMF). The improved pilot interval scheme and pilot power scheme can increase the system’s receiving sensitivity by 2 dB, respectively. These schemes can enhance the system’s performance without increasing the complexity of the algorithm and the costs of the RSSB system.

A 5–6-GHz CMOS Beamforming Transceiver Front-End for Fiber-to-the-Room All-Optical Wi-Fi Solution

This letter presents a 5–6-GHz CMOS beamforming transceiver front-end with high linearity and low power consumption for fiber-to-the-room (FTTR) all-optical Wi-Fi solution, which can greatly reduce the transmission power and eliminate signal mutual interference among access points compared with traditional architecture, by aggregating beams of multichannel. The transmitter (TX) employs a high-linearity power amplifier, a variable-gain amplifier, a 5-bit passive attenuator (ATT), and a 4-bit passive phase shifter (PS). The receiver (RX) is composed of a single-to-differential variable gain low-noise amplifier (LNA), frequency-tuning buffers, a 5-bit ATT, and a 4-bit PS. Implemented in a 55-nm CMOS technology, the measured output power 1dB compression point (OP1dB) of TX is better than 12.1 dBm. The error vector magnitudes (EVMs) of the TX at 0-dBm output power with 80-MHz 256-quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM) signal are better than −36.3 dB, and the EVMs of the RX at −40 dBm input power are better than −37.8 dB. The noise figure is 4.3 dB in high-gain mode.

Optimization of Partial Transmit Sequences for PAPR Reduction of OFDM Signals Without Side Information

This paper develops a novel optimization of partial transmit sequences (PTS) with phase quantization to reduce the peak-to-average-power ratio (PAPR) of orthogonal frequency-division multiplexing (OFDM) signals and enable data detection without side information. Since the formulated optimization problem is non-convex and has exponential time complexity, we employ a convex relaxation method to convert the original optimization problem into a series of convex programming whose solutions converge to a sub-optimal point satisfying the Karush-Kuhn-Tucker (KKT) conditions in polynomial time. Moreover, the obtained phase factors are quantized to enable the maximum likelihood (ML) phase estimation at the receiver, hence removing the need of sending side information. Analytical and numerical results are provided to show that our proposed PTS design achieves better PAPR reduction over existing PTS methods, while no performance degradation is incurred in data detection when the number of phase factors is properly chosen.

High Linear and Temperature Insensitive GaAs Power Amplifier Operating at 3.3–3.6 GHz Using a Multi-Feedback Branch Bias Circuit

This letter describes a design of a 3.3–3.6-GHz GaAs heterojunction bipolar transistor (HBT) power amplifier (PA) with high linearity and temperature insensitivity for the fifth-generation (5G) of new radios (NRs). By involving a multi-feedback branches bias circuit, the voltage at the feedback node of the bias circuit can achieve dynamic self-tuning to stabilize the base voltage as the amplifier’s input power grows and stabilize the bias current as the temperature increases as well. A three-stage common source structure PA in the form of a monolithic microwave integrated circuit (MMIC) is designed using a multi-feedback branch bias circuit with a size of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$1.5\times1.2$ </tex-math></inline-formula> mm. Measured with continuous wave (CW) signals, the output 1-dB compression point at 3.3–3.6 GHz is 34 dBm. The linearity of the PA is also evaluated using a 5G-NR 100-MHz 64-quadratic-amplitude modulated (QAM)-orthogonal frequency division multiplexing (OFDM) signal with a 7-dB peak-to-average-power ratio (PAPR). The proposed PA achieves an adjacent channel power ratio (ACPR) less than −49.5 dBc at an average power of 28 dBm with a power-added efficiency (PAE) of 20% without the use of digital pre-distortion (DPD). In the temperature range of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$- 40\,\,^{\circ }\text{C}$ </tex-math></inline-formula> to 120 °C, the variance of bias current, small signal gain, PAE, output power at 1-dB compression point (OP1dB), and ACPR is relatively minor. This design is ideally suited for 5G communication systems due to its high linearity and temperature insensitivity.

A Wideband Energy-Efficient Multi-Mode CMOS Digital Transmitter

This article presents a wideband, energy-efficient digital transmitter (DTX) suitable for multi-mode/multi-band wireless communication applications. It features various operation modes comprising Cartesian (Modes-1/-2) and multi-phase (Modes-3/-4) configurations utilizing LO clocks with different duty cycle in the interleaving/non-interleaving configurations. The multi-phase operation compromises polar and Cartesian features by mapping the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$I/Q$ </tex-math></inline-formula> signals into two non-orthogonal basis vectors with a 45° relative phase difference and a 3-bit phase selector scheme. The different operation modes are extensively analyzed and compared. Fabricated in a 40-nm CMOS process with an off-chip matching network, the proposed DTX occupies a core area of 0.72 mm2 and delivers 23.18-dBm RF peak power at 2.1 GHz from a 0.95-V supply voltage with drain/system efficiencies of 66.26%/52.59%, respectively. Utilizing a simple memory-less digital pre-distortion (DPD) for a 160-MHz four-channel 64-quadrature amplitude modulation (QAM) orthogonal frequency-division multiplexing (OFDM) signal, the DTX delivers an average <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$P _{\text {Out}}$ </tex-math></inline-formula> of 13.5/11.4/7.7/9.4 dBm, achieving an adjacent channel (power) ratio (ACL(P)R) of better than −42/−40/−40/−38 dBc and an average error vector magnitude (EVM) of −36/−34/−34/−32 dB, operating in Modes-1/-2/-3/-4, respectively. While transmitting a 200-MHz single-channel 256 (1024)-QAM OFDM signal at 2.4 GHz in Modes-1/-4, the average delivered output power is 14.11/9.29 (12.23/7.32) dBm with average drain and system efficiencies of 33.17%/26.3% (23.82%/22.83%) and 24.81%/22.85% (19.34%/18.81%), while the ACLR and EVM are better than −42/−41 (−43/−43) dBc and −34.6/−33.1 (−33.5/−33.9) dB, respectively.

Multiplex signal amplification strategy-based early-stage diagnosis of Parkinson's disease on a SERS-enabled LoC system.

In this paper, a multiplex signal amplification strategy was developed for the determination of miR-214 and miR-221 on a surface-enhanced Raman scattering (SERS)-enabled lab-on-a-chip (LoC) system to realize the early-stage diagnosis of Parkinson's disease (PD). The gold nanobipyramids (GNBPs) with great monodispersity were functionalized with Raman reporter molecules and hairpin DNA 1, serving as the SERS nanotags. The presence of targets can initial the strand displacement amplification (SDA) reaction and the numerous short-stranded trigger DNA (tDNA) can be released under the action of polymerase and nicking enzyme. Then, the tDNA can trigger the catalytic hairpin assembly (CHA) event between the SERS nanotags and the capture nanoprobes (Magnetic beads (MBs) modified with hairpin DNA 2), resulting in the aggregation of GNBPs on the MBs surface. The multiplex signal amplification contributed by the SDA-CHA strategy and the magnet-induced aggregation effect can ultimately lead to the significant improvement of the detection sensitivity and the limit of detection (LOD) was low to aM level with reproducibility and specificity meanwhile. Furthermore, a MPTP-induced PD mice model was established to verify the practicability and the expression level of miR-214 and miR-221 at different stages analyzed with the LoC system was confirmed by qRT-PCR.

Least squares decoding in binomial frequency division multiplexing

AbstractThis paper proposes a method that can reduce the complexity of a system matrix by analyzing the characteristics of a pseudoinverse matrix to receive a binomial frequency division multiplexing (BFDM) signal and decode it using the least squares (LS) method. The system matrix of BFDM can be expressed as a band matrix, and as this matrix contains many zeros, its amount of calculation when generating a transmission signal is quite small. The LS solution can be obtained by multiplying the received signal by the pseudoinverse matrix of the system matrix. The singular value decomposition of the system matrix indicates that the pseudoinverse matrix is a band matrix. The signal‐to‐interference ratio is obtained from their eigenvalues. Meanwhile, entries that do not contribute to signal generation are erased to enhance calculation efficiency. We decode the received signal using the pseudoinverse matrix and the removed pseudoinverse matrix to obtain the bit error rate performance and to analyze the difference.