Morse Taper Implants Research Articles

The Effect of a Positioning Index on the Biomechanical Stability of Tapered Implant-Abutment Connections

The biomechanical stability of the implant-abutment connection is critical for the success of implant-supported restorations. This study investigated the effect of a positioning index on the abutment screw preload values of tapered connection implants. Twenty Morse taper implants presenting an internal locking hex received 10 solid and 10 straight screw retained abutments for cemented single-crown restorations. Ten abutments had a positioning index to fit the internal locking hex of the implant (straight), and 10 were locked only by the implant taper (solid). The preload values for each abutment screw after a tightening torque were registered by strain gauges. Prosthetic crowns were placed on each abutment and subjected to mechanical cycling. Detorque forces were applied to each abutment and compared with the initial torque values. Data were statistically analyzed using Kolmogorov-Smirnov and Student t tests. The nonindexed group presented higher initial preload (6.05 N ± 0.95 N) compared with the indexed group (4.88 N ± 0.92 N; P < .05). After cycling, the nonindexed group exhibited less reduction of preload (13.84% ± 6.43%) compared with the indexed group (52.65% ± 14.81%; P < .01). Indexed tapered abutments for single-crown restorations might represent greater biomechanical risk under function.

The Role of Implant/Abutment System on Torque Maintenance of Retention Screws and Vertical Misfit of Implant-Supported Crowns Before and After Mechanical Cycling

This study aimed to evaluate the role of the implant/abutment system on torque maintenance of titanium retention screws and the vertical misfit of screw-retained implant-supported crowns before and after mechanical cycling. Three groups were studied: morse taper implants with conical abutments (MTC group), external-hexagon implants with conical abutments (EHC group), and external-hexagon implants with UCLA abutments (EHU group). Metallic crowns casted in cobalt-chromium alloy were used (n = 10). Retention screws received insertion torque and, after 3 minutes, initial detorque was measured. Crowns were retightened and submitted to cyclic loading testing under oblique loading (30 degrees) of 130 ± 10 N at 2 Hz of frequency, totaling 1 × 106 cycles. After cycling, final detorque was measured. Vertical misfit was measured using a stereomicroscope. Data were analyzed by analysis of variance, Tukey test, and Pearson correlation test (P < .05). All detorque values were lower than the insertion torque both before and after mechanical cycling. No statistically significant difference was observed among groups before mechanical cycling. After mechanical cycling, a statistically significantly lower loss of detorque was verified in the MTC group in comparison to the EHC group. Significantly lower vertical misfit values were noted after mechanical cycling but there was no difference among groups. There was no significant correlation between detorque values and vertical misfit. All groups presented a significant decrease of torque before and after mechanical cycling. The morse taper connection promoted the highest torque maintenance. Mechanical cycling reduced the vertical misfit of all groups, although no significant correlation between vertical misfit and torque loss was found.

Strain Gauge: study of strain distributions around three Morse taper prosthetic connections with offset positioning in machined and plastic copings under vertical load

The aim of this study was to evaluate through strain gauge the strain distribution occurred around 3 Morse taper implants with positioning offset, by varying the types of copings: plastic and machined. Microunit prosthetic abutments were connected onto the implant platforms. Ten frameworks composed of 3 copings were casted in cobalt-chromium alloy as single block (Co-Cr). Half of the copings were machined (n=5) and half were made of plastics (n=5). Four strain gauges were placed into the polyurethane block tangential to the 3 implants. The frameworks were fixed at their respective sites with the aid of a retaining screw with torque of 20 N.cm, achieve with a mechanical torquemeter. The vertical load of 30 Kg was applied through a spherical point of 2 mm diameter for 10 s, onto each one of the 3 screws of the framework through a device for load application The records of the strain reading were submitted to ANOVA and Tukey tests (5%). There were statistically significant differences (p=0.0174) between the coping type used (machined and plastic). The micro strain mean values were: point C at the machined coping 282.5 ?m (±120.8), point B at the machined coping 229.5 ?m (±76.1), point A at the machined coping 209.8 ?m (±55.0), point C at the plastic coping 155.0 ?m (±30.5), point B at the plastic coping 146.2 ?m (±25.8) and point A at the plastic coping 130.36 ?m (±21.83). It was concluded that there was a significant difference between the coping types, once the plastic coping exerted smaller micro strain on Morse taper implants than the machined copings.

Morse taper implants at different bone levels: a finite element analysis of stress distribution

Aim: To explore the biomechanical effects of the different implantation bone levels of Morse taper implants, employing a finite element analysis (FEA). Methods: Dental implants (TitamaxCM) with 4x13 mm and 4x11 mm, and their respective abutments with 3.5 mm height, simulating a screwed premolar metal-ceramic crown, had their design performed using the software AnsysWorkbench10.0. They were positioned in bone blocks, covered by 2.5 mm thickness of mucosa. The cortical bone was designed with 1.5 mm thickness and the trabecular bone completed the bone block. Four groups were formed: group 11CBL (11 mm implant length on cortical bone level), group 11TBL (11 mm implant length on trabecular bone level), group 13CBL (13mm implant length on cortical bone level) and group 13TBL (13 mm implant length on trabecular bone level). Oblique 200 N loads were applied. Von Mises equivalent stresses in cortical and trabecular bones were evaluated with the same design program. Results: The results were shown qualitatively and quantitatively by standard scales for each type of bone. By the results obtained, it can be suggested that positioning the implant completely in trabecular bone brings harm with respect to the generated stresses. Its implantation in the cortical bone has advantages with respect to better anchoring and locking, reflecting a better dissipation of the stresses along the implant/bone interfaces. In addition, the search for anchoring the implant in its apical region in cortical bone is of great value to improve stabilization and consequently better stress distribution. Conclusions: The implant position slightly below the bone in relation to the bone crest brings advantages as the best long-term predictability with respect to the expected neck bone loss.

Evaluation of Torque Maintenance of Abutment and Cylinder Screws With Morse Taper Implants

The screw loosening of implant-supported prostheses is a common mechanical failure and is related to several factors as insertion torque and preload. The aim of this study was to evaluate the torque maintenance of retention screws of tapered abutments and cylinders of Morse taper implants submitted to retightening and detorque measurements. Two groups were obtained (n = 12): group I-tapered abutment connected to the implant with titanium retention screw and group II-cylinder with metallic base connected to tapered abutment with titanium retention screw. The detorque values were measured by an analogic torque gauge after 3 minutes of torque insertion. The detorque was measured 10 times for each retention screw of groups I and II, totalizing 120 detorque measurements in each group. Data were submitted to ANOVA and Fisher exact test (P < 0.05). Both groups presented reduced detorque value (P < 0.05) in comparison to the insertion torque in all measurement periods. There was a statistically significant difference (P < 0.05) between the detorque values of the first measurement and the other measurement periods for the abutment screw. However, there was no statistically significant difference (P > 0.05) for the detorque values of all measurement periods for the cylinder screw. In conclusion, the abutment and cylinder screws exhibited torque loss after insertion, which indicates the need for retightening during function of the implant-supported prostheses.

Three-Dimensional Finite Element Analysis of Stress Distribution on Different Bony Ridges With Different Lengths of Morse Taper Implants and Prosthesis Dimensions

This finite element analysis (FEA) compared stress distribution on different bony ridges rehabilitated with different lengths of morse taper implants, varying dimensions of metal-ceramic crowns to maintain the occlusal alignment. Three-dimensional FE models were designed representing a posterior left side segment of the mandible: group control, 3 implants of 11 mm length; group 1, implants of 13 mm, 11 mm and 5 mm length; group 2, 1 implant of 11 mm and 2 implants of 5 mm length; and group 3, 3 implants of 5 mm length. The abutments heights were 3.5 mm for 13- and 11-mm implants (regular), and 0.8 mm for 5-mm implants (short). Evaluation was performed on Ansys software, oblique loads of 365N for molars and 200N for premolars. There was 50% higher stress on cortical bone for the short implants than regular implants. There was 80% higher stress on trabecular bone for the short implants than regular implants. There was higher stress concentration on the bone region of the short implants neck. However, these implants were capable of dissipating the stress to the bones, given the applied loads, but achieving near the threshold between elastic and plastic deformation to the trabecular bone. Distal implants and/or with biggest occlusal table generated greatest stress regions on the surrounding bone. It was concluded that patients requiring short implants associated with increased proportions implant prostheses need careful evaluation and occlusal adjustment, as a possible overload in these short implants, and even in regular ones, can generate stress beyond the physiological threshold of the surrounding bone, compromising the whole system.

Straight and Offset Implant Placement under Axial and Nonaxial Loads in Implant‐Supported Prostheses: Strain Gauge Analysis

The aim of this in vitro study was to quantify strain development during axial and nonaxial loading using strain gauge analysis for three-element implant-supported FPDs, varying the arrangement of implants: straight line (L) and offset (O). Three Morse taper implants arranged in a straight line and three implants arranged in an offset configuration were inserted into two polyurethane blocks. Microunit abutments were screwed onto the implants, applying a 20 Ncm torque. Plastic copings were screwed onto the abutments, which received standard wax patterns cast in Co-Cr alloy (n = 10). Four strain gauges were bonded onto the surface of each block tangential to the implants. The occlusal screws of the superstructure were tightened onto microunit abutments using 10 Ncm and then axial and nonaxial loading of 30 Kg was applied for 10 seconds on the center of each implant and at 1 and 2 mm from the implants, totaling nine load application points. The microdeformations determined at the nine points were recorded by four strain gauges, and the same procedure was performed for all of the frameworks. Three loadings were made per load application point. The magnitude of microstrain on each strain gauge was recorded in units of microstrain (με). The data were analyzed statistically by two-way ANOVA and Tukey's test (p < 0.05). The configuration factor was statistically significant (p= 0.0004), but the load factor (p= 0.2420) and the interaction between the two factors were not significant (p= 0.5494). Tukey's test revealed differences between axial offset (με) (183.2 ± 93.64) and axial straight line (285.3 ± 61.04) and differences between nonaxial 1 mm offset (201.0 ± 50.24) and nonaxial 1 mm straight line (315.8 ± 59.28). There was evidence that offset placement is capable of reducing the strain around an implant. In addition, the type of loading, axial force or nonaxial, did not have an influence until 2 mm.

Stress distribution in implant-supported prosthesis with external and internal implant-abutment connections

Objective. This study aimed to investigate the stress distribution in screwed implant-supported prostheses with different implant-abutment connections by using a photoelastic analysis. Materials and methods. Four photoelastic models were fabricated in PL-2 resin and divided according to the implant-abutment connection (external hexagon (EH) and Morse taper (MT) implants (3.75 × 11.5 mm)) and the number crowns (single and 3-unit piece). Models were positioned in a circular polariscope and 100-N axial and oblique (45) loading were applied in the occlusal surface of the crowns by using a universal testing machine. The stresses were photographically recorded and qualitatively analyzed using software (Adobe Photoshop). Results. Under axial loading, the MT implants exhibited a lower number of fringes for single-unit crowns than EH implants, whereas for a 3-unit piece the MT implants showed a higher number of fringes vs EH implants. The oblique loading increased the number of fringes for all groups. Conclusion. In conclusion, the MT implant-abutment connection reduced the amount of stress in single-unit crowns, for 3-unit piece crowns the amount of stress was lower using an external hexagon connection. The stress pattern was similar for all groups. Oblique loading promoted a higher stress concentration than axial loading.

Photoelastic Analysis of Stress Distribution With Different Implant Systems

The aim of this study was to evaluate stress distribution with different implant systems through photoelasticity. Five models were fabricated with photoelastic resin PL-2. Each model was composed of a block of photoelastic resin (10 × 40 × 45 mm) with an implant and a healing abutment: model 1, internal hexagon implant (4.0 × 10 mm; Conect AR, Conexão, São Paulo, Brazil); model 2, Morse taper/internal octagon implant (4.1 × 10 mm; Standard, Straumann ITI, Andover, Mass); model 3, Morse taper implant (4.0 × 10 mm; AR Morse, Conexão); model 4, locking taper implant (4.0 × 11 mm; Bicon, Boston, Mass); model 5, external hexagon implant (4.0 × 10 mm; Master Screw, Conexão). Axial and oblique load (45°) of 150 N were applied by a universal testing machine (EMIC-DL 3000), and a circular polariscope was used to visualize the stress. The results were photographed and analyzed qualitatively using Adobe Photoshop software. For the axial load, the greatest stress concentration was exhibited in the cervical and apical thirds. However, the highest number of isochromatic fringes was observed in the implant apex and in the cervical adjacent to the load direction in all models for the oblique load. Model 2 (Morse taper, internal octagon, Straumann ITI) presented the lowest stress concentration, while model 5 (external hexagon, Master Screw, Conexão) exhibited the greatest stress. It was concluded that Morse taper implants presented a more favorable stress distribution among the test groups. The external hexagon implant showed the highest stress concentration. Oblique load generated the highest stress in all models analyzed.

Photoelastic Analysis of Biomechanical Behavior of Single and Multiple Fixed Partial Prostheses With Different Prosthetic Connections

The aim of this study was to evaluate the stress distribution on external hexagon, internal hexagon, and Morse taper implant in single and 3-unit implant-supported fixed partial prostheses (FPPs) using photoelasticity. Six models were fabricated with the photoelastic resin PL-2: 3 models for the 3-unit implant-supported FPP with implants of 4.0 × 10.0 mm in the region of the second premolar and molar including 1 model for each type of implant connection, and 3 models for the single prosthesis for each implant type. The prostheses fabrication was standardized. A circular polariscope was used, and axial and oblique (45 degrees) loads of 100 N were applied in a universal testing machine. The results were photographed and analyzed qualitatively. The internal hexagon implant exhibited better stress distribution and lower intensity of fringes followed by the external hexagon and Morse taper implants for the models with the 3-unit prostheses. For the single implants, the Morse taper implant presented better stress distribution, followed by the internal and external hexagon implants. The oblique loading increased the number of photoelastic fringes in all models. It was concluded that the internal hexagon implant exhibited better biomechanical behavior for the 3-unit implant-supported FPP, whereas the Morse taper implant was more favorable for the single implant-supported prosthesis. The oblique loading increased the stress in all models.

Damping behavior of implant‐supported restorations

The aim of the present study was to assess the shock absorbing capacity of implant-supported restorations (CAD/CAM composite resin or zirconia abutment with composite resin or porcelain crown/onlay) and a simulated natural tooth complex using the Periometer(®) . One hundred and twenty Morse taper implants (Titamax CM 11mm) were mounted on bone-simulating acrylic resin base and restored with CAD/CAM zirconia (60) and metal composite resin Paradigm MZ100 (60) abutments. Using CEREC3, standardized onlays (60) and crowns (60) were designed and milled in ceramic (Paradigm C) or composite resin (Paradigm MZ100) to simulate a maxillary premolar. All restorations were luted with a preheated light curing composite resin (Filtek Z100). Fifteen extracted human upper premolars were mounted with a simulated PDL and used as control group. The Periometer(®) , a new handheld percussion probe that measures the energy loss coefficient (LC) for both natural teeth and implant-supported structures, was positioned perpendicularly to the buccal surface of each restoration. Three measurements of the LC were collected for each specimen. The effect of each variable (abutment material, restoration material, and restoration design) on the LC was explored using multiple regression analysis. Differences in LC between the abutment material (zirconia/Paradigm MZ100), the restoration material (Paradigm C/Paradigm MZ100) and the restoration design (onlay/crown) were recorded. The average LC of zirconia and metal composite resin abutments ranged from 0.040 to 0.053 and 0.059 to 0.068, respectively. Zirconia abutments restored with composite resin restorations (LC 0.051-0.053) had the closest LC value when compared with teeth with simulated PDL (0.049). Composite resin onlays/crowns bonded to zirconia implant abutments presented similar dynamic response to load (damping behavior) when compared to teeth with a simulated PDL.

Implantes cono Morse con sistema de indexación interno. Descripción del caso clínico

The use of Morse Taper implants with index to the installation with internal torque should be an interesting option to the design of a dental implant, It could even bring more prosthetic solutions to this system by the fact that the internal index could also be used as a reference for restorations. This article aims to describe a clinical case with the use of Morse Taper implants and a system of internal index, avoiding the use of an external mount, which already comes adapted from factory. The technique of flapless surgery associated to the Morse Taper implant with internal hex index demonstrated to be a safe procedure to the rehabilitation of the posterior edentulous region in the jaw.

Photoelastic Stress Analysis of Different Designs of Cement-Retained Fixed Partial Dentures on Morse Taper Oral Implants

There is no consensus in literature regarding the best plan for prosthetic rehabilitation with partial multiple adjacent implants to minimize stress generated in the bone-implant interface. The aim of this study was to evaluate the biomechanical behavior of cemented fixed partial dentures, splinted and nonsplinted, on Morse taper implants and with different types of coating material (ceramic and resin), using photoelastic stress analysis. A photoelastic model of an interposed edentulous space, missing a second premolar and a first molar, and rehabilitated with 4 different types of cemented crowns and supported by 2 adjacent implants was used. Groups were as follows: UC, splinted ceramic crowns; IC, nonsplinted ceramic crowns; UR, splinted resin crowns; and IR, nonsplinted resin crowns. Different vertical static loading conditions were performed: balanced occlusal load, 10 kgf; simultaneous punctiform load on the implanted premolar and molar, 10 kgf; and alternate punctiform load on the implanted premolar and molar, 5 kgf. Changes in stress distribution were analyzed in a polariscope, and digital photographs were taken of each condition to allow comparison of stress pattern distribution around the implants. Cementation of the fixed partial dentures generated stresses between implants. Splinted restorations distributed the stresses more evenly between the implants than nonsplinted when force was applied. Ceramic restorations presented better distribution of stresses than resin restorations. Based on the results obtained, it was concluded that splinted ceramic restorations promote better stress distribution around osseointegrated implants when compared with nonsplinted crowns; metal-ceramic restorations present less stress concentration and magnitude than metal-plastic restorations.

A comparative study of microstrain around three-morse taper implants with machined and plastic copings under axial loading

Aim: To evaluate the occurrence of microstrain around morse taper implants in straight configuration under axial load in a cast monoblock framework. Methods: Three implants were inserted in a polyurethane block and microunit abutments were installed on the implants with 20 Ncm torque. Plastic and machined copings were adapted on the preset waxing to fabricate the framework (n=5). Four strain gauges were attached on the upper surface of the block and then each framework was tightened on the abutments and a vertical load of 30 kg was applied to five points of the framework. Results: The data obtained in the strain gauge analysis were subjected to twoway ANOVA and Tukey’s test (α=0.05). There was statistically significant difference (p=0.0222) for the factor application point and the mean microstrain values were: application point B 402,04µe, point A 401.21µe, point E 390.44µe , point D 341.76µe and point C 309.19 µe. Conclusions: There was no microstrain difference between plastic and machined copings during axial loading. Difference in the application point was observed, but remained within bone physiological limits.

In Vitro Microbiological Bacterial Seal Analysis of the Implant/Abutment Connection in Morse Taper Implants: A Comparative Study Between 2 Abutments

The aim of this study was the comparative evaluation between 2 models of morse taper abutments, with regard to their performance in an in vitro bacterial seal analysis. Twenty-two morse taper implants, Titamax (Neodent, Curitiba, Brazil) CM 3, 75 x 13 mm, 11 CM Universal Post 4.5 x 2 x 2.5 mm, and 11 CM Universal Post Passing Bolt 4.5 x 4 x 2.5 mm were used. The implants were inoculated with 0.3 microL of the 10 concentrated Escherichia coli suspension in their internal screws. The solid posts were closed with 20 N/cm closure torque and the passing bolt posts with 10 N/cm. The assembled specimens were incubated aerobically at 37 degrees C for 7 days, with daily control for cloudiness. The broth in which assembled units showed contamination was diluted at 10 and plated. After incubation, the colonies were counted. Nonparametric Mann-Whitney and Fisher's exact tests were performed. The results showed no statistically significant difference between groups P and S with respect to number of colonies. When the total number of positive assembled units in each group was compared, no significant difference was found in either groups. We concluded that there was no statistically significant difference between the 2 models of abutment in an in vitro bacterial seal analysis.