Measurements Of Optical Properties Research Articles

Spectroscopic ellipsometry utilizing frequency division multiplexed lasers

Spectroscopic ellipsometry (SE), which measures the thickness of thin films in a non-contact way with an accuracy of angstroms, has been widely used for optical metrology. Several types of SE are available both commercially and in research, although they require specific implementations depending on the application. Here, we theoretically and experimentally demonstrate the Frequency Division Multiplexing Spectroscopic Ellipsometry (FDM-SE) technique. With respect to conventional rotating polarizing element ellipsometry, our variant uses discrete-wavelength intensity-modulated laser diodes. This modification enables the measurement of optical properties of materials at multiple wavelengths simultaneously. We further compare the performance of the FDM-SE to a commercial instrument by measuring the thickness of SiO2 films on a Si wafer, obtaining a difference between the measured thicknesses with both methods of less than 5 Å. The proposed FDM-SE technique therefore provides a more efficient alternative to conventional SE with a high accuracy for thickness measurements.

Measurement of inherent optical properties of water based on multiple scattering profile using underwater off-axis single-photon lidar

Measurement of inherent optical properties of water based on multiple scattering profile using underwater off-axis single-photon lidar

Thermochromic properties and surface chemical states of reactive magnetron sputtered vanadium oxide thin films at various deposition pressures

Vanadium oxide thin films were prepared using reactive magnetron sputtering method, varying the deposition pressures from 4 to 10 mTorr while maintaining the other sputtering parameters constant. Our investigations revealed sensitive dependence of deposition pressure, chemical states of the V and O atoms, crystal phases, and thermochromic (TC) optical modulation. Specifically, the film deposited at 8 mTorr displayed distinct TC characteristics with a prevalent monoclinic m-VO2 phase according to X-ray diffraction (XRD), supported by X-ray photoelectron spectroscopy (XPS). Optical transmittance modulation and electrical property measurements revealed a metal–insulator transition (MIT), confirming the intimate connection between TC characteristics and presence of the m-VO2 phase. Films deposited at pressures lower or higher than 8 mTorr exhibited typical semiconductor behavior without TC characteristics, further supported by in situ XRD, where (110) plane shifted to lower angle upon heating above τC. Chemical state analysis by XPS revealed a clear correlation between V−O peaks and the presence of a VO2 phase, with the film deposited at 8 mTorr displaying relatively large peak fitted area indicative of the VO2 phase. These findings highlight the critical and sensitive dependence of the deposition conditions in tailoring the properties of vanadium oxide thin films and provide valuable insights for potential applications in chromogenic films.

Shining light on environmental remediation: a type-II heterojunction MnFe2O4/rGO nanocomposites for enhanced photocatalytic degradation of organic dyes and bisphenol A.

In this study, the pressing issue of persistent organic pollutants in wastewater was addressed by designing and fabricating a magnetically separable MnFe2O4/rGO heterostructure catalyst for efficient mineralization of bisphenol A (BPA) and dyes such as alizarin red S (anionic) and malachite green (cationic), which are known for their resistance to biodegradation and carcinogenic properties. Comprehensive structural and surface analyses using XRD, XPS, SEM, and TEM/HRTEM coupled with magnetic and optical property measurements revealed the formation of the MnFe2O4/rGO heterostructures. Among all, the MnFe2O4/rGO-10 catalyst with 10% wt% of rGO exhibited 100% efficiency in the mineralization of BPA and both dyes under visible light illumination within 60min. The stability and recyclability of the catalyst, assessed through XRD and VSM studies, demonstrated its consistent performance over multiple uses. The cost-effectiveness and stability of this catalyst underscore its potential for practical application in wastewater treatment, offering a viable solution to the persistent challenge of removing stubborn organic contaminants.

Analysis and measurement of optical properties and time characterization of silica aerogel used as a Cherenkov radiator

X-rays generated by high-energy pulsed electron sources can be utilized in tumor treatment. The time spectrum measurement of pulsed electron sources enables precise treatment and provides feedback to the design and construction of accelerators. In this paper, silica aerogel samples of different densities and thicknesses were prepared as Cherenkov radiator. The transmittance and refractive index of these samples were measured, then the absorption and scattering lengths were calculated on the basis of the obtained transmittance. The obtained results were input into Geant4 software to get the intrinsic luminescence time of the silica aerogel of different densities and thicknesses. Finally, a measurement system was constructed with the silica aerogel samples, and the rise time of this system and the silica aerogel were measured by using a picosecond electron accelerator. The results demonstrate that the rise time of the measurement system is below 180 ps and that of the silica aerogel is less than 54.32 ps. It is also proved that the silica aerogel can be used as the Cherenkov radiator for the measurement of the time spectrum of high-energy pulsed electron sources.

Cross-wavelength calibrating method for real-time imaging of tissue optical properties using frequency-domain diffuse optical spectroscopy.

Frequency-domain diffuse optical spectroscopy (FD-DOS) is a powerful non-invasive technique for assessing tissue optical properties, with applications ranging from basic research to clinical diagnosis. In this study, we introduce and validate a novel approach termed the cross-wavelength calibrating (CWC) method within the framework of TrackDOSI, a real-time FD-DOS imaging system for tissue characterization. The CWC method aims to mitigate the effects of changing optical coupling and motion artifacts encountered during probe scanning, thus enhancing the accuracy and reliability of optical property measurements. Notably, the CWC method also allows for a simpler geometry with fewer sources than traditional self-calibrating (SC) methods, reducing instrumental complexity and cost while maintaining robustness in estimating optical properties. We first validate the CWC method on solid silicone phantoms, demonstrating strong agreement with the gold standard SC method with an error of -10% and 1% for absorption and reduced scattering coefficients, respectively. Furthermore, experiments on phantom and human tissue reveal the CWC approach's ability to suppress motion artifacts and optical coupling variations, thereby improving measurement repeatability, signal fidelity, and artifact correction in dynamic imaging scenarios. Our findings underscore the potential of the CWC method to enhance the clinical utility of DOSI techniques by enabling real-time artifact correction and improving the accuracy of tissue optical property measurements.

Secondary Brown Carbon Aerosol Resists Bleaching by Ozone under Acidic Conditions.

Light-absorbing organic aerosol (brown carbon, BrC) can affect Earth's radiative balance. However, owing to uncertainties in BrC sources, composition, and lifetime, the radiative impact of BrC is poorly constrained. In particular, the effects of heterogeneous oxidation and the influence of aerosol pH on the lifetime and light absorption properties of BrC are not well established. In a series of laboratory experiments, we characterize the changes in the chemical composition and optical properties of BrC aerosol upon heterogeneous oxidation by ozone (O3). BrC analogs were generated by reacting glyoxal with ammonium sulfate in bulk solutions. The resulting solutions were pH adjusted before being atomized and oxidized in a flow reactor, with online measurements of the aerosol optical and chemical properties to monitor changes from oxidation. For the conditions investigated here, we find that ozonolysis diminishes the ability of BrC material to absorb light, presumably due to the degradation of the BrC chromophores. While the BrC has a lifetime of 1-2 h due to ozonolysis, it effectively stops bleaching after <6 h of atmospheric processing, leaving behind an ozone (O3) resistant fraction of BrC. We observed a pH dependence on oxidation and bleaching with acidic BrC bleaching more slowly and remaining more absorbing than more basic samples. Given that submicron atmospheric aerosols are typically acidic and rapidly undergo partial bleaching, we suggest that the complex refractive index (RI; m) of secondary glyoxal-ammonium BrC should be modeled using data from the recalcitrant fraction of acidic aerosols. This study reports aerosols generated from a pH = 1.51 solution having a RI of m = 1.48 + 1.2 × 10-3 i and m = 1.53 + 2.9 × 10-4 i at 405 and 532 nm, respectively after aging with O3. A comprehensive treatment of BrC lifetime will require this process to be considered in conjunction with other bleaching mechanisms such as photolysis and reactions with OH.

Towards a sensing model using a random laser combined with diffuse reflectance spectroscopy.

The previous research proves that the random laser emission reflects not only the scattering properties but also the absorption properties. The random laser is therefore considered a potential tool for optical properties sensing. Although the qualitative sensing using the random laser is extensively investigated, a quantitative measurement of optical properties is still rare. In this study, a generalized mathematical quantitative model using random laser combined with diffuse reflectance spectroscopy is proposed for optical sensing in turbid media. This model describes the gain effect of the active medium and the optical properties effect of the passive medium separately. Rhodamine 6G is used as the active medium. Intralipid and ink are employed to demonstrate the effect of the scattering and absorption, respectively. The peak wavelength shift of the random laser is proved to be an ideal sensing parameter for this sensing model. It is also revealed that the scaling parameters in the sensing model are interrelated and can be simplified to one. With this combined model, the direct sensing of optical properties in diverse turbid media is promising.

Observations of circumstellar disks in scattered light with SPHERE at the VLT

The technological developments initiated in the early 21 st century have led to the implementation of “planet finders” instruments on 8-m class telescopes which are in operation since 2014-2015. Such facilities are at the inception of significant progresses in the study of exoplanetary systems by enabling high contrast imaging of the environment of young nearby stars. One of the most productive science in this field is certainly the observations at high angular resolution of circumstellar disks, from the very young gas-rich protoplanetary disks all the way to more elusive dust-rich debris disks. In this paper, we summarize the main results obtained for these two categories of objects focusing on their morphological characteristics, as well as on the measurement of optical properties of the small dust particles to which the near IR spectral range is sensitive to. We mostly provide exemples based on observations performed with the SPHERE instrument at the VLT.

Optimizing the composition of barium-borate glasses for enhancing thermal neutron shielding efficiency: Monte Carlo simulation

A transparent window with thermal neutron shielding properties was an important part of the stations of the nuclear reactors and the particle accelerators. The borate glass with a high neutron cross section was a candidate as a glass network for the neutron shielding window. In order to slow down thermal neutrons, they were trapped by boron and subsequently emitted secondary radiation, such as alpha particles and gamma-ray radiation. This work was to optimize the content between a ratio of borate with a high cross-section neutron interaction and barium for shielding alpha and gamma ray. The barium-borate glasses were successfully synthesized using the melting technique in the atmosphere. Measurements of mechanical and optical glass properties were presented. The measured results showed that an increase in barium oxide content in the glass ratio enhanced the glass density and the transmittance at a visible wavelength. In the calculation of radiation shielding properties, FLUKA code based on Monte Carlo Simulation was demonstrated. The calculated results revealed that an increase in the barium oxide content in the glass composition reduced the thermal neutron shielding properties of the glass samples. In contrast, the glass with barium contents enhanced the photon-shielding efficiency, as indicated by the mass attenuation coefficient and half-value layer. Not only the ratio of the barium and borate contents affected the shielding properties, but the increased glass thickness also enhanced the shielding properties. Thus, the utilization of cooperative borate glasses and barium with appropriate thickness could potentially serve as a viable option for simultaneously protecting against thermal neutrons and photons. The barium-borate glasses with our composition might be used as a window in a thermal neutron station as well as for photon radiation.

On the impact of radiative transfer in fluorescence imaging of bacterial films and suspensions

Fluorescence imaging and spectroscopy are convenient, rapid, and simple methods to analyze chemical samples including biological materials such as bacterial biofilms and suspensions. In principle, these techniques could be used to diagnose or discriminate between infectious bacteria in infections of the skin or ocular surface (microbial keratitis, MK). However, the extension of these techniques to macroscopic turbid media that strongly absorb and scatter light is difficult. Radiative transfer effects obscure the relationship between microscopic scattering and absorption properties and macroscopically observable quantities such as fluorescence intensity, transmission, and reflection. A combination of experimental measurements of aqueous bacteria cell suspensions and Monte Carlo radiation transfer simulations are performed to better understand these effects. Several general observations, e.g., that fluorescence intensity is maximized in scattering-dominated media, are discussed in detail. It was found that wavelength-dependent radiative transfer effects are observable even at moderate optical densities (OD ∼ 1; well below the diffusion limit). Careful consideration of radiative transfer effects using physically rigorous models is needed to determine single-cell scattering and absorption properties and interpret quantitative fluorescence measurements accurately in most cases of interest. A detailed discussion of radiative transfer effects and analytical models is provided. In the context of surface infections and MK, it was found that radiative transfer effects may be negligible for the model bacteria E. coli in some cases. However, more accurate measurements of microbe optical properties are needed to confirm and extend this conclusion to other species. Overall this work demonstrates that quantitative fluorescence imaging and spectroscopy of bacterial films and suspensions is feasible, but requires detailed sample characterization and careful consideration of radiative transfer effects.

MgHg(SeO3)2(H2O)2: A magnesium mercury selenite with large birefringence

Selenite crystalline materials have been popular owing to the diverse structures and optical performances. A new mercury selenite, MgHg(SeO3)2(H2O)2, was synthesized by using a conventional hydrothermal method. It crystallizes in the monoclinic structure with a C2/c space group, MgHg(SeO3)2(H2O)2 exhibits a three-dimensional (3D) structure, which is made up of [Hg(SeO3)2]2–∞ chains and distorted MgO4(H2O)2 octahedra. Besides, it presents a large birefringence of 0.137 @ 546 nm according to experimental measurement. Synthesis, crystal structure, thermal stability, optical property measurements and theoretical studies were performed in this work.

Experimental setup for the measurement of optical properties in the vacuum ultraviolet region

Abstract This work presents an experimental setup designed for measuring optical properties in the vacuum ultraviolet (VUV) region. Originally developed for the characterization of ICARUS photomultiplier tubes, the setup has been recently employed to measure the conversion efficiency of para-Terphenyl coatings, acting as wavelength shifters, as a function of thickness. The VUV region is of particular interest in particle physics experiments utilizing cryogenic noble gases as scintillating media. The setup includes a deuterium light source, a mirror system, an intensity monitor, and a sample chamber to host sample and photodetector. An example measurement of para-Terphenyl conversion efficiency — as wavelength shifter — with varying thickness is presented, demonstrating the versatility and effectiveness of the presented system.

Methylene blue photodynamic therapy of deep tissue abscesses: Phase 1 clinical trial and optical spectroscopy results

SignificanceDeep tissue abscesses represent a significant source of morbidity and hospital stay, with standard of care drainage failing in many cases. We investigated photodynamic therapy (PDT) as an adjunct to standard of care, to reduce or eliminate bacterial burden. ApproachA Phase 1 clinical trial was performed to evaluate safety and feasibility of methylene blue (MB) PDT at the time of abscess drainage. Immediately following drainage, MB-PDT was performed. Diffuse reflectance spectroscopy was performed to evaluate abscess wall optical properties. ResultsNo study-related adverse events were noted, and no side effects were observed. PDT was well tolerated by all subjects, and infused MB was recovered in all cases. Optical property measurements showed variability in hemoglobin concentration and oxygenation, as well as MB uptake, between subjects. ConclusionsMB-PDT at the time of percutaneous abscess drainage was safe and feasible, and optical property measurements showed wide variance between subjects.

Low-cost Green Synthesis of Silica Engineering Nanomaterials from Rice Husk (Agriculture waste) and its Physical and Luminescent Properties Measurements

The electrical, electronics,and drug industries are heavily reliant on the use of Silica materials for several applications. Green source of production of silica materials is very important to meet the growing demandfor industrial purposes. The present work discusses the recent nanosilica production using low-costmethods, from rice husk-agricultural waste, andtheir structural, microstructural, and optical properties measurement for its applications.The crystallite size of silica particleswas measured using XRD is 26 nm and 55 nm, which are prepared from rice husk synthesized by both coprecipitation and leaching processes, respectively.. The SEM images of both the samples showed structural order of the pores within the mesoporous structure. The leached sample showed a purity of around 80%. The infrared spectral data also supports the presence of hydrogen-bonded silanol groups and the siloxane groups in the silica. These nanosilica particles showed Photoluminescence in UV, Visible, and NIR regions. The nanoscale silica formation is also confirmed by TEM and DLS measurements. Zeta Potential studies found -22.12 mV reveals the stability of prepared nano silica for a longer duration.

Measurements of the inherent optical properties of aqueous suspensions of microplastics

AbstractLibraries of inherent optical properties (IOPs) of microplastics are sparse, yet they are essential for the development of optical techniques to detect and quantify microplastics in the ocean. In this study, we describe our results and technique for the measurement of the IOPs of microplastic suspensions generated from commonly utilized plastics. The measurements included angle‐resolved polarized light scattering, and spectral absorption and beam attenuation coefficients. We also performed ancillary characterization of particle properties, including size distribution, shape, and mass concentration of suspended matter. We observed several unique optical characteristics regarding absorption, scattering, and polarization properties compared with typical marine particle assemblages. We show that these results are useful for radiative transfer simulations as well as the potential development of novel plastic detection techniques from above‐ or in‐water optical measurements.

A Non-Destructive Study of Optical, Geometric and Luminescent Parameters of Active Optical Fibers Preforms

This work is devoted to the scientific and technical aspects of individual stages of active optical fibers preforms’ optical-geometric parameters metrological control. The concept of a system presented makes it possible to carry out a study of a rare earth element distribution in the preform of an active optical fiber and to monitor geometric parameters, and also to study the evolution of the refractive index profile along the length of the sample at a qualitative level. As far as it is known, it is the first description of the preform optical, geometric, and luminescent properties measurement within a single automated laboratory bench. Also, the novelty of the approach lies in the fact that the study of the refractive index profile variation along the length of the preform is, for the first time, conducted using the “dry” method, that is, without immersing the sample in synthetic oil, which makes the process less labor-intensive and safer.

Treatment planning for photodynamic therapy of abscess cavities using patient-specific optical properties measured prior to illumination

Photodynamic therapy (PDT) is an effective antimicrobial therapy that we used to treat human abscess cavities in a Phase 1 clinical trial. This trial included pre-PDT measurements of abscess optical properties, which affect light dose (light fluence) at the abscess wall and PDT response. This study simulated PDT treatment planning for 13 subjects that received optical spectroscopy prior to clinical PDT, to determine the impact of measured optical properties on ability to achieve fluence rate targets in 95% of the abscess wall. Retrospective treatment plans were evaluated for 3 conditions: (1) clinically delivered laser power and assumed, homogeneous optical properties, (2) clinically delivered laser power and measured, homogeneous optical properties, and (3) with patient-specific treatment planning using measured, homogeneous optical properties. Treatment plans modified delivered laser power, intra-cavity Intralipid (scatterer) concentration, and laser fiber type. Using flat-cleaved laser fibers, the proportion of subjects achieving 95% abscess wall coverage decreased significantly relative to assumed optical properties when using measured values for 4 mW cm−2 (92% versus 38%, p = 0.01) and 20 mW cm−2 (62% versus 15%, p = 0.04) thresholds. When measured optical properties were incorporated into treatment planning, the 4 mW cm−2 target was achieved for all cases. After treatment planning, optimal Intralipid concentration across subjects was 0.14 ± 0.09%, whereas 1% was used clinically. Required laser power to achieve the 4 mW cm−2 target was significantly correlated with measured abscess wall absorption (ρ = 0.7, p = 0.008), but not abscess surface area (ρ = 0.2, p = 0.53). When using spherical diffuser fibers for illumination, both optimal Intralipid concentration (p = 0.0005) and required laser power (p = 0.0002) decreased compared to flat cleaved fibers. At 0% Intralipid concentration, the 4 mW cm−2 target could only be achieved for 69% of subjects for flat-cleaved fibers, compared to 100% for spherical diffusers. Based on large inter-subject variations in optical properties, individualized treatment planning is essential for abscess photodynamic therapy. (Clinical Trial Registration: The parent clinical trial from which these data were acquired is registered on ClinicalTrials.gov as ‘Safety and Feasibility Study of Methylene Blue Photodynamic Therapy to Sterilize Deep Tissue Abscess Cavities,’ with ClinicalTrials.gov identifier NCT02240498).

Mixed-state ptychography for quantitative optical properties measurement of vector beam.

Recent advances in ptychography have extended to anisotropic specimens, but vectorial reconstruction of probes owing to polarization aliasing remains a challenge. A polarization-sensitive ptychography that enables full optical property measurement of vector light is proposed. An optimized reconstruction strategy, first calibrating the propagation direction and then performing faithful retrieval, is established. This method avoids multiple image acquisitions with various polarizer configurations and significantly improves the measurement accuracy by correlating the intensity and position of different polarization components. The capability of the proposed method to quantify anisotropic parameters of optical materials and polarization properties of vector probe is demonstrated by experiment.

Higher absorption enhancement of black carbon in summer shown by 2-year measurements at the high-altitude mountain site of Pic du Midi Observatory in the French Pyrenees

Abstract. Black-carbon-containing particles strongly absorb light, causing substantial radiative heating of the atmosphere. The climate-relevant properties of black carbon (BC) are poorly constrained in high-altitude mountain regions, where many complex interactions between BC, radiation, clouds and snow have important climate implications. This study presents 2-year measurements of BC microphysical and optical properties at the Pic du Midi (PDM) research station, a high-altitude observatory located at 2877 m above sea level in the French Pyrenees. Among the long-term monitoring sites in the world, PDM is subject to limited influence from the planetary boundary layer (PBL), making it a suitable site for characterizing the BC in the free troposphere (FT). The classification of the dominant aerosol type using aerosol spectral optical properties indicates that BC is the predominant aerosol absorption component at PDM and controls the variation in single-scattering albedo (SSA) throughout the 2 years. Single-particle soot photometer (SP2) measurements of refractory BC (rBC) show a mean mass concentration (MrBC) of 35 ng m−3 and a relatively constant rBC core mass-equivalent diameter of about 180 nm, which are typical values for remote mountain sites. Combining the MrBC with in situ absorption measurements, a rBC mass absorption cross-section (MACrBC) of 9.2 ± 3.7 m2 g−1 at λ=880 nm has been obtained, which corresponds to an absorption enhancement (Eabs) of ∼2.2 compared to that of bare rBC particles with equal rBC core size distribution. A significant reduction in the ΔMrBC/ΔCO ratio when precipitation occurred along the air mass transport suggests wet removal of rBC. However we found that the wet removal process did not affect the rBC size, resulting in unchanged Eabs. We observed a large seasonal contrast in rBC properties with higher MrBC and Eabs in summer than in winter. In winter a high diurnal variability in MrBC (Eabs) with higher (lower) values in the middle of the day was linked to the injection of rBC originating from the PBL. On the contrary, in summer, MrBC showed no diurnal variation despite more frequent PBL conditions, implying that MrBC fluctuations are rather dominated by regional and long-range transport in the FT. Combining the ΔMrBC/ΔCO ratio with air mass transport analysis, we observed additional sources from biomass burning in summer leading to an increase in MrBC and Eabs. The diurnal pattern of Eabs in summer was opposite to that observed in winter with maximum values of ∼2.9 observed at midday. We suggest that this daily variation may result from a photochemical process driving the rBC mixing state rather than a change in BC emission sources. Such direct 2-year observations of BC properties provide quantitative constraints for both regional and global climate models and have the potential to close the gap between model-predicted and observed effects of BC on the regional radiation budget and climate. The results demonstrate the complex influence of BC emission sources, transport pathways, atmospheric dynamics and chemical reactivity in driving the light absorption of BC.