Maximum Radial Stress Research Articles

Transversely isotropic elastoplastic behaviour in a mechanically loaded rotating disk

This article deals with the study of transversely isotropic elastoplastic behaviour in a mechanical loaded rotating disk by using transition theory and generalised strain measure. Magnesium material disk requires higher value of angular speed to yield at the inner surface as compared to the disk made of beryl material. With the effect of mechanical loading, angular speed also increases at the inner surface of the disk made of magnesium/beryl. Upon the introduction of mechanical loading, the rotating disk made of beryl material requires maximum radial stress at the inner surface as compared to disk made of magnesium material. The beryl material disk is more convenient than that of magnesium material.

An experimental and theoretical investigation on residual stress of 7075-T651 aluminum alloy hole under electromagnetic cold expansion

The electromagnetic cold expansion process (ECE) was adopted in this work. The theoretical plastic radius, hole wall stress, radial stress, circumferential stress and release stress under different expansion rates (ER) were studied based on thick cylinder theory and ECE experiments. The released strain, residual stress (RS) and failure force were measured. The tensile fracture morphology was characterized. The results showed that the theoretical plastic radius (maximum 15.87 mm), internal stress (maximum 982.9 MPa), radial stress (maximum −820.9 MPa) and circumferential stress (maximum −271.4 MPa) increased with the increase of ER. The absolute radial and circumferential stress decreased and increased in negative and positive ranges respectively with distance increased. The release strain (maximum −3033 με, 10−6 microstrain), radial RS (maximum 600.9 MPa) and circumferential RS (maximum 601.1 MPa) also increased with the increase of ER, and the minimum relative error of the plastic zone radius of the theoretical model was 3.78 % proving the reliability of the model. In addition, ECE increased the release stress (the maximum radial and circumferential release stresses were 1402.6 MPa and 747.5 MPa) and decreased the failure force (minimum 44.7kN) with increased ER. The initial crack position tended to transition from the inlet and outlet surfaces to the middle position, and the crack propagation angle and axial crack size gradually decreased with the decreased ER and stress level.

Modeling 3D TGO dynamic growth and stresses and the resulting modes of buckling failure in thermal barrier coatings

AbstractBased on experimental data, this study presents a model of the dynamic growth of a thermally grown oxide (TGO) in thermal barrier coatings (TBCs) during thermal cycling. The model was solved using the finite element method. The thermal stress results of the model were compared with experimental results to verify the accuracy of the model. The stress analysis revealed that the combined effect of radial tensile stress and circumferential compressive stress can lead to the delamination of TBCs in a buckling form, which can induce the formation of cracks in TBCs along the axial direction. This observation was consistent with the conclusions drawn from the experimental results. Crack initiation and propagation result from the action of the maximum shear and radial stresses. In addition, the relationship between buckling failure and microscopic cracks was investigated. Thermal cycling induces radial and circumferential cracks, leading to buckling, delamination, and ultimate coating failure as the radial and circumferential cracks interact at the interface.

Numerical Simulation of Geothermal Energy Development at Mount Meager and Its Impact on In Situ Thermal Stress

The Meager Mountain Geothermal Project stands as one of the pioneering geothermal energy initiatives in its early stages of resource development. Despite its abundant geothermal heat resources, no prior studies have systematically evaluated the potential of implementing coaxial borehole heat exchangers on site. This study addresses this research gap by presenting a comprehensive heat transfer model for an underground closed-loop geothermal system utilizing a single coaxial well. Finite element analysis incorporated fluid and solid heat transfer, as well as solid mechanics. The results obtained facilitated the construction of the temperature and thermal stress profiles induced by the cooling effects resulting from years of heat extraction. After 25 years of operation, the outlet temperature has reached approximately 74 °C, and the maximum radial tensile thermal stress amounts to ~47 MPa. Furthermore, the analysis demonstrates that higher fluid velocities contribute to more perturbed temperature and stress distributions. The study attained maximum thermal and electric power outputs of 208 kW and 17 kW, respectively. This research also underscores the significant impact of geothermal gradient and well length on BHE design, with longer wells yielding more power, especially at higher injection velocities.

Advanced taper tension profile for improved control performance in roll-to-roll winding processes

Products coated with flexible film can be stored in wound rolls after the winding process. However, if the roll product experiences excessive internal stress, it can lead to various defects in the coated layer. To alleviate the stress within the wound roll, a taper tension profile is utilized to progressively reduce tension as the winding length increases. As a substantial amount of web is wound onto the core, the moment of inertia of the wound roll increases. It has been observed that, as the winding length increases, the tension control performance of the taper tension tends to deteriorate. We propose an advanced taper tension profile to enhance tension control performance and validates the effectiveness of this profile through winding experiments. It was observed that, compared to the parabolic taper tension, maximum tension error could be reduced by approximately 16.1 % throughout the winding process. This reduction in tension error enables the preservation of the radial stress reduction effect of the taper tension, resulting in a 13.3 % decrease in the maximum radial stress compared to the parabolic taper tension. The proposed taper tension profile contributes to a more uniform quality of the coated layer, especially as the maximum winding length is extended.

Mechanical response of long-span CFST arch bridges based on the hydration heat temperature effect

As the span of concrete-filled steel tube (CFST) arch bridges increases, the hydration heat temperature effect of concrete inside steel tube becomes more severe, which increases the safety risk during the construction process. Therefore, a numerical simulation of the mechanical response of a long-span CFST arch bridge under the influence of hydration heat was carried out. First, based on the hydration heat conduction theory, a finite element model of the transient temperature field of a CFST arch rib was established. The temperature distribution of the CFST arch rib and its variation with time were revealed, and an approximate formula for the distribution of the hydration heat temperature along the radial direction of the CFST was provided. Subsequently, the variation law of the thermal stress of a CFST during hydration heat release was investigated. Finally, based on the principle of temperature equivalence, a finite element model of the overall CFST arch rib was established to examine the effect of hydration heat on the deformation of the arch rib. The results reveal that the hydration heat temperature field of the CFST arch rib exhibits nonlinear and axisymmetric characteristics. The maximum temperature of the section and the maximum temperature difference can reach 73.5 °C and 33.2 °C, respectively. Because of the influence of the hydration heat, there is a significant stress gradient in the cross section of the arch rib. A maximum radial stress of 2.08 MPa is attained, indicating a risk of concrete cracking. Additionally, the displacement along the transverse and vertical directions of the chord tube exhibits an initial increase, followed by a decrease over time. The maximum transverse displacement of the chord tube reaches 70.6 mm, while the vertical displacement reaches 117.8 mm.

Multi-objective optimization of membrane cavity curve of diaphragm compressor and its verification

According to the trend of compressor upgrades in hydrogen refueling stations, this article optimizes the single exponential curve of membrane chamber volume and diaphragm stress that performs poorly. First, set the optimization goals as the membrane cavity volume and the arc length of the curve, use the MOPSO algorithm to optimize the curve, and fit the optimization results to obtain a new curve mathematical model. Then, select three curves for comparison. Theoretical calculations and finite element simulations were performed on the membrane cavity volume and diaphragm stress, and the theoretical calculation methods and results were verified with the help of existing experiments. Finally, it was found that the new curve can increase the membrane cavity volume and reduce the diaphragm stress requirement by changing its own parameters, and the new curve has a small amount of cavity volume near the transition point, which has little impact on the membrane cavity volume. Under the same maximum radial stress, the membrane cavity volume of the new curve can be increased by 5.56% compared to the single exponential curve, while under the same membrane cavity volume, the new curve can reduce the maximum stress on the gas side by 8.9% compared with the single exponential curve, and the maximum stress on the oil sides is reduced by 9.8%.

Comparison of the effects of induction heating composite shot peening and conventional shot peening on residual stress, microhardness, and microstructure of 20CrMnTi gear steel

As a commonly used surface strengthening technology, shot peening, which can significantly improve the fatigue strength of mechanical parts, is widely used in the fields of vehicles and aviation. To obtain a larger residual compressive stress and further refine the grain size under normal shot peening intensity and coverage, this study proposes an induction heating composite shot peening (IHCSP) surface strengthening method, aiming to utilize the coupling effect of temperature and stress fields to promote the shot peening strengthening effect. An IHCSP test plan was designed and an IHCSP test bench was created to achieve simultaneous induction heating and shot peening. This study compares the surface integrity parameters and microstructures under three processes: un-peened, conventional shot peening, and IHCSP. The results show that the maximum axial and radial compressive residual stresses increase by 72.41 and 75.4 MPa respectively; the depth of the hardened layer increases by 0.3 mm, the martensitic transformation more complete, the grain size decreases by 483 nm, the dislocation density increases significantly, and nanocrystals are obtained on the surface of the material. These results verify the superiority of IHCSP surface strengthening.

Mechanics behavior and failure mechanism of the intralayer carbon/glass hybrid rod

AbstractThe carbon/glass hybrid rod exhibits high tensile strength, light weight, and strong corrosion resistance. However, the bottleneck of interlayer splitting exists in the interlayer hybrid rod, severely impeding safe operation. To solve the problem of rod splitting, this paper proposed a new scheme of an intralayer carbon/glass hybrid rod. Based on the material constitutive model, a full‐scale simulation model was developed. The stress distribution and deformation of the hybrid rod were analyzed and the progressive damage mechanism of the hybrid rod was explained. The results indicated that, for the intralayer carbon/glass hybrid rod, (a) the ultimate experimental tensile load witnessed a significant increase, rising by 14.0% from 452.4 to 515.7 kN compared to the interlayer hybrid rod; (b) the numerical model predicted the tensile load of 525.9 kN, with an error of 1.9% compared to the test result, meeting engineering accuracy requirements; (c) the elastic deformation stage saw a 146.7% increase from 280.2 to 691.3 MPa in the maximum axial stress of the carbon‐fiber layer, and a 120% increase from 89.8 to 198.0 MPa in the maximum radial stress of the glass fiber layer as the tensile displacement increased from 0.16 to 0.32 mm. In conclusion, the intralayer carbon/glass hybrid rod proposed in this paper can significantly improve the tensile strength compared to the interlayer hybrid rod, which can accelerate the application of carbon/glass hybrid rods in oil and gas fields.Highlights According to the problem of interlayer splitting in the interlayer carbon/glass hybrid rods, a novel scheme of an intralayer carbon/glass hybrid rod was proposed. Based on the material constitutive model, a full‐scale simulation model of an intralayer carbon/glass hybrid rod was developed to analyze the stress distribution and deformation response under tensile load. The dynamic progressive damage analysis method for intralayer carbon/glass hybrid rods was proposed to reveal the damage evolution mechanism.

Numerical simulation of bulk superconductor during pulsed field magnetization based on multi-field coupled analysis

High-temperature bulk superconductors are widely used in various superconducting devices due to their high critical current density, which enables them to trap high magnetic fields. However, the critical current density of bulk superconductors is influenced by magnetic field, temperature and stress, and both increase of stress and temperature can lead to a decrease in the critical current density. And the influence of magnetic field, current, stress are interactional. In this paper, the multi-field coupled analysis is employed to investigate the electromagnetic and mechanical behavior on bulk superconductor during pulsed field magnetization. The simulation results were compared with the present experimental results. The results showed a good agreement between the simulation and experimental results, further validating the reliability of the numerical simulation method. The magnetic field, current, temperature, and stress distribution and variation within the bulk sample during the pulsed magnetization process were calculated and analyzed. Additionally, the influence of the central crack and edge crack in the bulk superconductor was investigated. The results indicate that the region near the crack experiences a variation in current flow direction, resulting in local temperature rise and significant electromagnetic forces. The tip of the crack exhibits stress concentration, leading to a decrease in critical current density. Bulk supercondutor with edge crack case exhibits greater stress concentration compared to those with central crack case. The impact of crack length on maximum stress was analyzed, revealing that as the crack length increases, both the maximum hoop stress and radial stress within the bulk sample rise.

Effect of structure of unfluxed burnt titanomagnetite pellets on strength under static compression

Burnt pellets must retain their strength from the moment they are taken out of an induration machine until they are loaded into a blast furnace. One of the indicators of the burnt pellets’ strength is the compressive strength, i.e. the ultimate force. In experiments to determine compressive strength, the main type of fracture is occurrence and development of cracks that pass through the core center of pellets (where the maximum radial tensile stresses present) or near it. The paper presents the requirements for static compression strength imposed by blast furnace production to iron ore pellets. Using an optical and scanning electron microscope equipped with an energy-dispersive microanalyzer, we analyzed the relationship of structural components and pores in the core of burnt unfluxed iron ore titanomagnetite pellets with the ultimate force under static compression. By scanning electron microscopy and X-ray spectral microanalysis, it was established that the core of pellets is a multiphase material, and its main phases are titanomagnetite, magnetite, titanohematite, hematite and aluminosilicate binder. Optical microscopy made it possible to establish the microstructure of the pellet core, which has three types of microstructures: non-oxidized core (magnetite or titanomagnetite), partially oxidized core – around (magnetite or titanomagnetite) hematite grains (titanohematite) and oxidized core (hematite and titanohematite). The main factors for obtaining pellets with an ultimate force of more than 2.5 kN/pellet according to the requirements of blast furnace production are: the number of closed macropores and the number of large grains in the core. It is shown that with an increase in the number of closed macropores and the number of large grains in the core, the ultimate force is reduced from 3.5 kN to 0.87kN/pellet.

Advective gas flow in bentonite: Development and comparison of enhanced multi-phase numerical approaches

Understanding the impact of repository gas, generated from degradation of waste and its interaction with the host rock, is essential when assessing the performance and safety function of long-term disposal systems for radioactive waste. Numerical models based on conventional multi-phase flow theory have historically been applied to predict the outcome and impact of gas flow on different repository components. However, they remain unable to describe the full complexity of the physical processes observed in water-saturated experiments (e.g., creation of dilatant pathways) and thus, the development of novel representations for their description is required when assessing fully saturated clay-based systems. This was the primary focus of Task A within the international cooperative project DECOVALEX-2019 (D-2019) and refinement of these approaches is the primary focus of this study (Task B in the current phase of DECOVALEX-2023).This paper summarises development of enhanced numerical representations of key processes and compares the performance of each model against high-quality laboratory test data. Experimental data reveals that gas percolation in water-saturated compacted bentonite is characterised by four key features: (i) a quiescence phase, followed by (ii) the gas breakthrough, which leads to a (iii) peak value, which is then followed by (iv) a negative decay. Three models based on the multiphase flow theory have been developed. These models can provide good initial values and reasonable responses for gas breakthrough (although some of them still predict a too-smooth response). Peak gas pressure values are in general reasonably well captured, although maximum radial stress differences are observed at 48 mm from the base of the sample. Here, numerical peak values of 12.8 MPa are predicted, whereas experimental values are about 11 MPa. These models are also capable of providing a reasonable representation of the negative pressure decay following peak pressure. However, other key specific features (such as the timing of gas breakthrough) still require a better representation. The model simulations and their comparison with experimental data show that these models need to be further improved with respect to model parameter calibration, the numerical representation of spatial heterogeneities in material properties and flow localisation, and the upscaling of the related physical processes and parameters. To further understand gas flow localisation, a new conceptual model has been developed, which shows that discrete channels can possibly be induced through the instability of gas-bentonite interface during gas injection, thus providing a new perspective for modeling gas percolation in low-permeability deformable media.

Flux jump and mechanical response in inhomogeneous high-temperature superconductor under the pulsed-field magnetization

The high-temperature bulk superconductors with high critical current density are brittle, and can be damaged by large Lorentz forces and thermal stress during magnetization. Several studies have reported the failure of bulk superconductors during flux jumps. In this study, we analyzed the magnetization characteristics and mechanical response of the HTS bulk with inhomogeneous current density along the c-axis. The numerical simulation was consistent with the experimental results presented in the reference. Moreover, a flux jump occurred near the area of the pre-arrangement flux during the second pulsed field magnetization. The maximum temperature is lower than the critical temperature during the flux jump. In the mechanical analysis, the flux jump led to an abrupt change in the maximum stress of the bulk, and the maximum radial stress was significantly higher than the maximum hoop stress during the flux jump. The maximum radial stress increased with decreasing ambient temperature during the flux jump, and the maximum stress area was always near the seeded plane. Subsequently, the magnetization characteristics and mechanical response were studied for different locations of the seeded surface, two concentric superconducting bulks, and non-uniform fields.

Investigation on Optical Absorption and Reflection of Carbon Nanotubes Mixed Copper Composites for Laser Sintering Process Improvement

Selective laser sintering (SLS) of copper components manufactured via powder metallurgy is widely studied due to minimal material wastage. However, copper has poor optical absorption when exposed to infrared (IR) lasers, such as in laser-based additive manufacturing or laser surface processing. To address this issue, an innovative approach to enhance the optical absorption of copper powders during infrared laser sintering is presented in this study. Carbon nanotubes (CNTs) have several unique properties, including their high surface area, plasmonic response, excellent conductivity, and optical absorption properties. CNTs were mixed with copper powders at different weight percentages using an acoustic method. The resulting Cu-CNT compositions were fabricated into pellets. The Box-Behnken Design of Experiments methodology was used to optimize the IR laser processing conditions for sintering. Spectroscopic analysis was conducted to evaluate the reflection and thermal absorption of the IR wavelengths by the Cu-CNT composites. Density and hardness measurements were taken for the laser-sintered Cu-CNT pellets. The coating of copper powders with CNTs demonstrated enhanced optical absorption and correspondingly reduced reflection. Due to the enhanced optical absorption, increased control and sensitivity of the laser sintering process was achieved, which enabled improvement in the mechanical properties of strength, hardness, and density, while also enabling control over the composite thermal expansion coefficient. A maximum average hardness of 66.5 HV was observed. Indentation test results of the samples revealed maximum tangential and radial stresses of 0.148 MPa and 0.058 Mpa, respectively.

Optimization of functionally graded polycrystalline diamond compact based on residual stress: Numerical simulation and experimental verification

Polycrystalline diamond compact (PDC) is composed of a polycrystalline diamond layer with a tungsten carbide substrate, which is commonly used on drill bits. PDC bits are widely used in geological and petroleum drilling. There are frequently issues with failure, such as chipping of teeth during drilling, attributed to the residual stress within the PDC. Residual stresses arise from the difference in material properties between the polycrystalline diamond layer and the tungsten carbide substrate after sintering and cooling. To address the residual stresses inside the PDC, this research work optimized the design of a PDC with a functionally graded structure is reported in this paper. The effect of gradient structural parameters on the residual stresses of the PDC is analyzed using the finite element method. The results show that as the thickness of the gradient structural layer increases, the maximum residual tensile stress gradually decreases and stabilizes. Since the total thickness of the gradient structural layer is fixed, increasing the layer number (decreasing the thickness of the single layer) cannot reduce the maximum tensile stress, but it can minimize the sudden change of axial stress across the interface, thus resulting in less interface cracking. The optimum gradient structure design parameters are obtained and the optimal graded PDC is prepared via fused deposition modeling and sintering technology, resulting in a 62% reduction in maximum shear stress, a 70% decrease in maximum axial stress, and a 40% drop in maximum radial stress compared to conventional PDC. The accuracy of the finite element calculations is demonstrated by the Raman spectroscopy results. This work will provide a reliable guide for the design of functional graded structure PDCs and lay the foundation for their preparation and application.

Ice and Snow on Lake Stemmevatnet, Spitsbergen, in Winter 2019/20

Received January 19, 2023 ;revised March 22, 2023; accepted June 27, 2023The results of observations and modeling of the formation of the snow-ice cover of Lake Stemme (West Svalbard Island) in winter 2019/20 are presented. The main information was obtained by two radar (GPR) survey, performed on the floating ice of the Lake on March 12 and April 22 of 2020. Authors believe that probably these observations were the first ones on the Lake. The use of the radar made it possible to obtain data on the dynamics of the thickness of the layers of snow and ice cover, the so-called “snow ice” which is formed when the boundary between snow and ice was submerged under water. During the time between records, the thickness of the last “snow ice” increased two to three times, i.e., from units to the first tens of cm, and it spread to the entire deep-water part of the Lake area. In addition, analysis of high-precision positioning of the radar records revealed a significant deflection in the ice surface in the central part of the Lake under the influence of snow load and the decreasing level of the reservoir. The calculations of the thermodynamics of the floating ice cover have shown that its thickening occurs as a result of the processes of congelation and isostatic ice formation, replacing each other at its lower and upper boundaries, respectively. At the same time, the formation of “snow ice” violates the characteristic feature of decreasing of ice thickness with growth of the snow thickness, which significantly influences on the thermal and mass balance of the Lake snow-ice cover. Results of calculations of the ice cover deformation did show that it takes place not only due to the elastic, but also to the viscous properties of ice, and it is concentrated in a narrow coastal zone. The maximum radial stress is reached at a distance of several meters from the shore, where a circular crack parallel to the shoreline is formed. Such a crack is formed at all ice thicknesses at about the same distance from the shore.

Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy.

Multiple cold expansion holes are widely used in connection areas of aircraft structures, in order to achieve uniform load transfer of the skin or connection parts. Split sleeve cold expansion (SSCE) is widely used to enhance the fatigue life of fastener holes by applying compressive residual stresses around the holes. In this study, the finite element method (FEM) was used to research the distribution and variation of residual stresses along the hole edges of 7075AA single-hole and multi-hole cold expansion (CE) specimens. Full-field strain measurements of single-hole and multi-hole specimens were performed using two-dimensional digital image correlation (DIC), and the residual stress and strain at the hole edge of the specimens measured by FEM and DIC were compared. FEM results shows that the maximum circumferential and radial residual stresses of three-hole specimens with three-hole spacing are increased by 5.37% and 31.53% compared with single-hole specimens. The maximum circumferential residual stress of three-hole specimens with four-hole spacing increases by 7.25% compared with a single hole, but the radial residual stress decreases by 12.98%. In addition, for three-hole specimens with hole spacing three times the hole diameter, the strengthening effect of SSCE in the order of middle hole, then left hole, and, finally, right hole is better than that of SSCE in the order of left to right hole. FEM and DIC full-field strain results are basically consistent.

Assessment of the stressed-strained state of a reinforced transport pipe under the combined effect of ambient temperature and static loads

The object of this study is a reinforced three-layer transport pipe, which is subjected to the joint action of ambient temperature and static loading of the road subgrade soil. The analytical model for assessing the stressed-strained state of reinforced three-layer pipes, under the combined action of temperature and static loads, has been improved using the theory of elasticity. The stressed-strained state of the reinforced pipe was assessed taking into account the values of the joint action of temperature and loads from vehicles, the physical and mechanical parameters of structural materials, and the geometric parameters of the pipe. As a result of the calculation of the reinforced multilayer pipe, it was found that the maximum movements that occur on the outside of the defective pipe are 0.64 mm, the metal pipe – 0.75 mm, and in the concrete mortar (fine-grained concrete) – 0.69 mm. It was established that under the combined action of ambient temperature and static loads from the road subgrade soil, ring stresses are maximum. They are 151 MPa. Axial stresses are also high – 141 MPa. At the same time, the maximum radial stresses are the smallest – 37.4 MPa. It has been established that a small difference in displacements occurs on the contact of structural materials of the reinforced pipe. However, the magnitude of the stresses is high. The maximum difference in ring stresses was 73 MPa, while the difference in radial and axial stresses was up to 1.0 MPa. It has been established that to restore the bearing capacity of damaged reinforced concrete pipes, it is possible to use the repair technology by the method of "sleeving". It involves pulling a metal pipe into the middle of the layer damaged with concrete mortar remaining between the concrete defective and the new metal pipes.

INFLUENCE OF THE SEALING ON APPEARANCE AND TRANSMISSION OF TEMPERATURE DEFORMATIONS IN ELECTRONIC MODULES

The scientific result presented in this paper consists in development of the Lame-Gadolin theory about interaction of joint thick-walled cylinders application to estimate strength of electronic components represented by bodies of revolution and surrounding layer of compound sealed by an arbitrary shape subjected to thermal impacts in the temperature range from +70 to -60 deg C. The difference in the coefficients of linear thermal expansion and other physical and mechanical characteristics of compound and electronic components under the temperature changes produces a contact pressure on their contact area causing thermal strain and stress in materials of both bodies in the sealed structure. Within the framework of the axisymmetric problem, the stress-strain condition of the electronic component-compound system has been assessed in condition of thermal impact, due to which the pattern of the maximum total radial, circumferential and axial stresses has been revealed depending on their radial distribution and the temperature load mode. The stress estimation in the S2-29V resistor sealed with the EZK-25 compound inside the sealed electronic package has been performed at the constant temperature drop. The experimental method is proposed for determining the ultimate stresses in electronic components sealed with compound under stress and strain condition identical to the operational one. Experimental measurement of circumferential and axial strains was carried out by using method of electrotensometry. Thermal impacts were reproduced in the thermostat and the climatic chamber. Technological methods for protection of electronic components in the structures of electronic packages sealed with compound has been proposed by embedding elastic and dissipative joints between electronic components and a sealant, and the effectiveness of their application is experimentally evaluated based on determination of the damping coefficient.

Initiation and Fracture Characteristics of Different Width Cracks of Concretes under Compressional Loading

A stress concentration at a crack tip may cause fracture initiation even under low-stress conditions. The maximum axial stress theory meets the challenges of explaining the fracture propagation of a non-closed fracture of cracked concretes under compressional loading. Uniaxial loading tests of single-crack concrete specimens were carried out and a numerical simulation of fracture propagation under uniaxial compression was performed. The radial shear stress criterion for a mode-II fracture is proposed to examine the stress intensity factor (SIF) of the pre-crack specimens under compressional loading. When the maximum radial shear stress at the crack tip is larger than the maximum axial tensile stress, and the maximum dimensionless SIFs can satisfy frθmax/fθmax > 1 and frθmax/fθmax > KIIC/KIC (fθmax=KIe/σyπa and frθmax=KIIe/σyπa are maximum dimensionless mode-I and mode-II SIFs, respectively), the crack will extend along the direction of the maximum radial shear stress. The influence of the single-crack angle and width on the mechanical properties of the specimens was examined. The experimental and numerical results indicate that the existence of cracks can considerably weaken the strength of the specimen. The distribution and width of the cracks had a significant effect on the specimen strength. The strength of the concrete specimen initially decreased and then increased with increasing fracture angle. The failure mechanism and rupture angle of pre-crack brittle material while considering crack width will be discovered.