Magnetic Recoil Neutron Spectrometer Research Articles

High-yield magnetic recoil neutron spectrometer on the National Ignition Facility for operation up to 60 MJ.

Recent progress at the National Ignition Facility (NIF), with neutron yields of order 1 × 1017, places new constraints on diagnostics used to characterize implosion performance. The Magnetic Recoil neutron Spectrometer (MRS), which is routinely used to measure yield, ion temperature (Tion), and down-scatter ratio (dsr), has been adapted to allow measurements of dsr up to 5 × 1017, and yield and Tion up to 2 × 1018 in the near term with new data processing techniques and conversion foil solutions. This paper presents a solution for extending MRS operation up to a yield of 2 × 1019 (60 MJ) by moving the spectrometer outside of the NIF shield wall. This will not only enhance the upper yield limit by 10× but also improve signal-to-background by 5×.

Measurement of apparent ion temperature using the magnetic recoil spectrometer at the OMEGA laser facility.

The Magnetic Recoil neutron Spectrometer (MRS) at the OMEGA laser facility has been routinely used to measure deuterium-tritium (DT) yield and areal density in cryogenically layered implosions since 2008. Recently, operation of the OMEGA MRS in higher-resolution mode with a new smaller, thinner (4 cm2, 57 μm thick) CD2 conversion foil has also enabled inference of the apparent DT ion temperature (T ion) from MRS data. MRS-inferred T ion compares well with T ion as measured using neutron time-of-flight spectrometers, which is important as it demonstrates good understanding of the very different systematics associated with the two independent measurements. The MRS resolution in this configuration, ΔE MRS = 0.91 MeV FWHM, is still higher than that required for a high-precision T ion measurement. We show how fielding a smaller foil closer to the target chamber center and redesigning the MRS detector array could bring the resolution to ΔE MRS = 0.45 MeV, reducing the systematic T ion uncertainty by more than a factor of 4.

High-resolution measurements of the DT neutron spectrum using new CD foils in the Magnetic Recoil neutron Spectrometer (MRS) on the National Ignition Facility.

The Magnetic Recoil neutron Spectrometer (MRS) on the National Ignition Facility measures the DT neutron spectrum from cryogenically layered inertial confinement fusion implosions. Yield, areal density, apparent ion temperature, and directional fluid flow are inferred from the MRS data. This paper describes recent advances in MRS measurements of the primary peak using new, thinner, reduced-area deuterated plastic (CD) conversion foils. The new foils allow operation of MRS at yields 2 orders of magnitude higher than previously possible, at a resolution down to ∼200 keV FWHM.

Measurements of fuel and ablator ρR in Symmetry-Capsule implosions with the Magnetic Recoil neutron Spectrometer (MRS) on the National Ignition Facility.

The Magnetic Recoil neutron Spectrometer (MRS) on the National Ignition Facility (NIF) measures the neutron spectrum in the energy range of 4-20 MeV. This paper describes MRS measurements of DT-fuel and CH-ablator ρR in DT gas-filled symmetry-capsule implosions at the NIF. DT-fuel ρR's of 80-140 mg/cm(2) and CH-ablator ρR's of 400-680 mg/cm(2) are inferred from MRS data. The measurements were facilitated by an improved correction of neutron-induced background in the low-energy part of the MRS spectrum. This work demonstrates the accurate utilization of the complete MRS-measured neutron spectrum for diagnosing NIF DT implosions.

Measurements of collective fuel velocities in deuterium-tritium exploding pusher and cryogenically layered deuterium-tritium implosions on the NIF

For the first time, quantitative measurements of collective fuel velocities in Inertial Confinement Fusion implosions at the National Ignition Facility are reported. Velocities along the line-of-sight (LOS) of the Magnetic Recoil neutron Spectrometer (MRS), positioned close to the equator (73°–324°), were inferred from the measured mean energy of the deuterium-tritium (DT)-primary neutron peak. Substantial mean energy shifts up to 113 ± 16 keV were observed in DT gas-filled exploding-pusher implosions, driven in a polar-direct drive configuration, which corresponds to bulk fuel velocities up to 210 ± 30 km/s. In contrast, only marginal bulk fuel velocities along the MRS LOS were observed in cryogenically layered DT implosions. Integrated analysis of data from a large number of cryogenically layered implosions has recently identified a deficit in achieved hot-spot energy of ∼3 kJ for these implosions [C. Cerjan et al., Phys. Plasmas (2013)]. One hypothesis that could explain this missing energy is a collective, directional fuel velocity of ∼190 km/s. As only marginal bulk fuel velocities are observed in the MRS data, this might indicate that turbulent or radial flows would be a likely explanation for the missing energy. However, a directional velocity close to perpendicular to the MRS LOS cannot be ruled out.

Fabrication of Thin CH and CD Films and Patterned Films Using a Heat Press Technique for the NIF and OMEGA Magnetic Recoil Neutron Spectrometer

Deuterated polyethylene films as thin as 50 μm have been produced using a four-post heated press method. These films are then cut into the desired shape (foil) and are used for the magnetic recoil spectrometer (MRS). The MRS is a diagnostic tool for inertial confinement fusion (ICF) experiments at the National Ignition Facility (NIF) and at the OMEGA Laser Facility at the University of Rochester Laboratory for Laser Energetics. The films produced by this method are more uniform and have fewer defects than foils prepared by previous methods. Whereas traditional films had a thickness limitation of 100 μm, this new heat pressing method allows the fabrication of 50-μm films, which is the desired thickness for MRS foils. The foils produced and characterized by General Atomics have decreased the neutron measurement uncertainty of the MRS instrument by a factor of 2 compared to the previous foils. This work has also been extended to fabricate thin polymer films and films with sinusoidal patterns from other polymeric materials for ICF experiments. This paper will discuss the heat pressing technique used in the fabrication of these films for the NIF and OMEGA MRS as well as other patterned and flat polymer films. The morphology of these foils and the advantages that they provide will also be discussed.

An accelerator based fusion-product source for development of inertial confinement fusion nuclear diagnostics

A fusion-product source, utilizing a 150 kV Cockraft-Walton linear accelerator, has been refurbished to provide a reliable nuclear diagnostic development tool to the national inertial confinement fusion (ICF) research program. The accelerator is capable of routinely generating DD reaction rates at approximately 10(7)/s when using a 150 kV, 150 microA deuterium (D) beam onto an erbium (Er) or titanium (Ti) target doped with D, and D(3)He reaction rates at approximately 5 x 10(5)/s when using a using a 120 kV, approximately 100 microA D beam onto a Er or Ti target doped with (3)He. The new accelerator is currently being used in a number of projects related to the national ICF program at the OMEGA Laser Fusion Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)], which includes the wedge range filter charged-particle spectrometry program [F. H. Seguin et al., Rev. Sci Instrum. 75, 3520 (2004)] and the magnetic recoil neutron spectrometer [J. A. Frenje et al., Rev. Sci. Instrum. 72, 854 (2001)].