Low Discharge Research Articles

Разработка и исследование имитационной модели мультикамерного разрядника для грозозащитного троса

Optical fiber overhead ground wire (OPGW) is an effective solution for laying mainline digital communications along high-voltage power lines. It allows you to use the existing infrastructure of the power grid and ensure the transfer of a large amount of data. The flow of lightning currents and short-circuit currents can cause a violation of the thermal resistance of the fiber and a deterioration of its performance. When the OPGW is insulated through an insulator shunted by a spark gap, during operation it is possible to change the distance in the discharge gap due to the displacement of the electrodes in the plane. Also, when the short circuit location is close, multiple overlaps will occur and as a result, short circuit current will flow through the OPGW. Thus, the article considers the possibility to use a device with a multielectrode system developed on the principle of a multichamber spark gap as a replacement of the spark gap to increase the reliability of the unit with an isolated OPGW suspension. Modeling of the device has been carried out in the ANSYS Maxwell software package, the mathematical apparatus of which is based on the use of Maxwell's differential equations and the finite element method, which allows performing numerical modeling with sufficiently high accuracy. A simulation model of a multichamber spark gap has been developed in the ANSYS Maxwell software package and calculations of electrical characteristics have been performed. For the electrode system of a multi-chamber arrester, an uneven distribution of the applied voltage across the spark discharge gaps of the chambers is determined. It is shown that when a voltage is applied to a spark gap, the highest electric field strength occurs between the first and second electrodes, and then a cascade of discharge gaps occurs, which provides the required low discharge voltages of the spark gap as a whole. The developed simplified simulation model of a multi-chamber arrester has shown all the necessary conditions for cascade imaging of the voltage distribution and the electric-field strength of various electrode options. Based on the research conducted electrodes geometry is identified for smart prototype development and ongoing multi-chamber arrester research.

Field physical model tests on the mechanism of river blocking by debris flow in the middle reaches of the Dadu River, Southwest China.

Debris flow is a typical natural disaster in the middle reaches of the Dadu River, Southwest China. Field physical model tests were conducted to reveal the mechanism of river blocking by debris flow in the middle reaches of the Dadu River. The dynamic processes of riHver blocking by debris flows were revealed, and based on which three typical river-blocking modes of debris flow are observed, i.e. thrust-type river blocking, mixed-flow-type river blocking and progressive river blocking. The test results showed that the material composition of debris flows plays an important role in the river-blocking mode, only the tests that adopted the mixed soil and gravel exhibited the thrust-type river blocking mode. The material composition has a controlling effect on the thrust-type river-blocking model. Mixed-flow-type river-blocking mode appears most often in the tests with an intersection angle of 60°, because the small intersection angle is conducive to the mixing of the debris flow and the water in the main channel. The debris flows composed of sand tend to block the river with mixed-flow-type river-blocking mode, accounting for 50% of the occurrences in the model tests. The high flow rate and discharge in the main channel and the low flow rate and discharge in the branch channel are the key factors controlling the progressive river-blocking mode. The test results in this study can support the debris flow disaster prevention and mitigation in this area.

Nano-silicon embedded in mildly-exfoliated graphite for lithium-ion battery anode materials

Silicon-based materials have a high theoretical specific capacity and a low discharge potential, whereas the significant capacity fading owing to weak conductivity and volume exfoliation effect. The co-utilization of silicon and graphite has become a feasible method for realizing high-performance lithium-ion batteries (LIBs). Herein, the C@p-Si/ESG composite anode material with “sandwich” structure was obtained by electrostatic assembly of mildly-exfoliated graphite and electrostatic modified nano silicon, and subsequent coated with amorphous carbon on the surface of the material. The carbon coating and the mildly-exfoliated graphite form a buffer space, which alleviates the volume expansion effect of silicon in the process of lithium alloying. In addition, the SEI film is generated outside the carbon layer, reducing the consumption of the electrolyte and the occurrence of side reactions. C@p-Si/ESG exhibits a high charge–discharge rate and an excellent long-term cycle stability.

High-pressure liquid refrigerant injection for reciprocating compressors

Isentropic (adiabatic) compression of superheated vapor in vapor compression refrigeration cycles usually results in some discharge superheat, i.e. the discharge temperature exceeding the condensing temperature. Large discharge superheat reduces both operating range and compression efficiency. Sub-isentropic compression with heat rejection to the heat sink is therefore superior to adiabatic compression, as it results in lower discharge superheat and improved efficiency. However, significant temperature reduction by heat transfer through the working chamber walls is difficult to facilitate in common refrigeration compressors, particularly reciprocating compressors. Refrigerant and oil injection is a well-established method for reducing temperatures and increasing efficiency in screw and scroll compressors, as well as multi-stage systems. In comparison, effective methods for temperature reduction in single-stage reciprocating compressors are fairly limited. Therefore, a concept for high-pressure liquid injection is proposed. By means of a pump and injection valve, high-pressure liquid refrigerant is injected into the working chamber and atomized. The compressed gas is cooled through the evaporation of the injected liquid. The injection valve allows for control over the injection timing and quantity, enabling adjustment of the temperature profile, which is a major distinction from existing refrigerant injection methods. The coupled compression-injection process is evaluated for various refrigerants using an energetic chamber model. The injection is found to be particularly suitable for refrigerants with a large evaporation heat and a shallow dew line slope. For the example of ammonia, a theoretical reduction in compression work of 8.9% at an evaporation temperature of −10 °C and a condensing temperature of 45 °C is found.

Neural networks and particle swarm for transformer oil diagnosis by dissolved gas analysis

The lifetime of power transformers is closely related to the insulating oil performance. This latter can degrade according to overheating, electric arcs, low or high energy discharges, etc. Such degradation can lead to transformer failures or breakdowns. Early detection of these problems is one of the most important steps to avoid such failures. More efficient diagnostic systems, such as artificial intelligence techniques, are recommended to overcome the limitations of the classical methods. This work deals with diagnosing the power transformer insulating oil by analysis of dissolved gases using new techniques. For this, we have proposed intelligent techniques based on Multilayer artificial neural networks (ANN). Thus, a multi-layer ANN-based model for fault detection is presented. To improve its classification rate, this one was optimized by a meta-heuristic technique as the particle swarm optimization (PSO) technique. Optimized ANNs have never been used in transformer insulating oil diagnostics so far. The robustness and effectiveness of the proposed model is demonstrated, and high accuracy is obtained.

Cobalt-catalyzed soft-hard carbon composite anodes for enhanced sodium-ion storage

Hard carbon is expected to be a high-capacity anode material for sodium-ion batteries (SIBs). However, its Na+ storage performance, especially the low discharge capacity, remains a great challenge. Herein, the soft-hard carbon composite anodes with high degree of graphitization were synthesized via low-temperature pyrolysis (at only 900 °C) of Cobalt-catalyzed perylene tetracarboxylic dianhydride (PTCDA-Co) and cotton, with subsequent removal of cobalt. The composite resulting from a 2:3 mass ratio of soft to hard carbon exhibits a good discharge capacity of 355.81 mAh g−1 at a current density of 50 mA g−1 and an enhanced initial Coulombic efficiency (ICE) of 81.41%. The enhanced electrochemical storage performance of cotton is attributed to the introduction of PTCDA-Co, which creates low-defect graphitic layer, hierarchical porous channels, and carbon shielding coating on hard carbon.

Intraoperative methadone for day-case gynaecological laparoscopy: A double-blind, randomised controlled trial.

Optimal pain relief in day-case surgery is imperative to patient comfort and timely discharge from hospital. Short-acting opioids are commonly used for analgesia in modern anaesthesia, allowing rapid recovery after surgery. Plasma concentration fluctuations from repeated dosing of short-acting opioids can cause patients to oscillate between analgesia with potential adverse effects, and inadequate analgesia requiring rescue dosing. Methadone's unique pharmacology may offer effective and sustained analgesia with less opioid consumption, potentially reducing adverse effects. Using a double-blind, randomised controlled trial, we compared post-anaesthesia care unit opioid consumption between day-case gynaecological laparoscopy patients who received either intravenous methadone (10 mg), or short-acting opioids intraoperatively. The primary outcome was post-anaesthesia care unit opioid consumption in oral morphine equivalents. Secondary outcomes included total opioid consumption, discharge opioid consumption, pain scores (0-10) until discharge, adverse effects (respiratory depression, postoperative nausea and vomiting, excess sedation), and rate of admission. Seventy patients were randomly assigned. Patients who received methadone consumed on average 9.44 mg fewer oral morphine equivalents in the post-anaesthesia care unit than the short-acting group (18.02 mg vs 27.46 mg, respectively, 95% confidence interval 0.003 to 18.88, P = 0.050) and experienced lower postoperative pain scores at every time point, although absolute differences were small. There was no evidence of lower hospital or discharge opioid consumption. No significant differences between the methadone and short-acting groups in other outcomes were identified: respiratory depression 41.2% versus 31.4%, Padjusted >0.99; postoperative nausea and vomiting 29.4% versus 42.9%, Padjusted >0.99; overnight admission 17.7% versus 11.4%, Padjusted >0.99; excess sedation 8.82% versus 8.57%, Padjusted >0.99. This study provides evidence that, although modestly, methadone can reduce post-anaesthesia care unit opioid consumption and postoperative pain scores after day-case gynaecological laparoscopy. There were no significant differences in any secondary outcomes.

Anion–Cation Competition Chemistry for Comprehensive High‐Performance Prussian Blue Analogs Cathodes

AbstractThe extensively studied Prussian blue analogs (PBAs) in various batteries are limited by their low discharge capacity, or subpar rate etc., which are solely reliant on the cation (de)intercalation mechanism. In contrast to the currently predominant focus on cations, we report the overlooked anion‐cation competition chemistry (Cl−, K+, Zn2+) stimulated by high‐voltage scanning. With our designed anion‐cation combinations, the KFeMnHCF cathode battery delivers comprehensively superior discharge performance, including voltage plateau >2.0 V (vs. Zn/Zn2+), capacity >150 mAh g−1, rate capability with capacity maintenance above 96 % from 0.6 to 5 A g−1, and cyclic stability exceeding 3000 cycles. We further verify that such comprehensive improvement of electrochemical performance utilizing anion‐cation competition chemistry is universal for different types of PBAs. Our work would pave a new and efficient road towards the next‐generation high‐performance PBAs cathode batteries.

Anion-Cation Competition Chemistry for Comprehensive High-Performance Prussian Blue Analogs Cathodes.

The extensively studied Prussian blue analogs (PBAs) in various batteries are limited by their low discharge capacity, or subpar rate etc., which are solely reliant on the cation (de)intercalation mechanism. In contrast to the currently predominant focus on cations, we report the overlooked anion-cation competition chemistry (Cl-, K+, Zn2+) stimulated by high-voltage scanning. With our designed anion-cation combinations, the KFeMnHCF cathode battery delivers comprehensively superior discharge performance, including voltage plateau >2.0 V (vs. Zn/Zn2+), capacity >150 mAh g-1, rate capability with capacity maintenance above 96 % from 0.6 to 5 A g-1, and cyclic stability exceeding 3000 cycles. We further verify that such comprehensive improvement of electrochemical performance utilizing anion-cation competition chemistry is universal for different types of PBAs. Our work would pave a new and efficient road towards the next-generation high-performance PBAs cathode batteries.

Nitrogen plasma treated cotton fabrics coated with SiO2 followed by RGO deposition for water purification process

Experimental investigations have been carried out to modify the surface properties of Cotton fabrics using low temperature DC glow discharge nitrogen plasma. Plasma treatment is an eco-friendly, dry and clean process over wet chemical methods and does not suffer from any environmental and health concerns [1]. The important plasma parameters such as power and working pressure are kept constant with various treatment times (5, 15, 30, and 60 mins). The plasma-treated cotton fabrics are optimized by XRD, FTIR, and SEM. A comparative study has been done for the untreated and different treated fibers. Pure SiO2 is coated on untreated and nitrogen plasma treated cotton fabrics by sputtering method. The samples are coated for different sputtering times (10 and 30 min). Finally, Reduced Graphene Oxide (RGO) is coated on plasma treated SiO2 deposited fabrics. RGO is prepared by modified hummers methods [2]. Our results provide a way to develop a filter for water purification.

Deformation mechanism and treatment effect of deeply excavated expansive soil slopes with high groundwater level: Case study of MR-SNWTP, China

Taking a 4 km long deeply excavated expansive soil canal segment of the South–North Water Transfer Project Middle Route (MR-SNWTP) in China as an example, a comprehensive investigation of the deformation mechanism and effect of treatment work on the slope with high groundwater level was carried out. First, the project background and initial behaviour were introduced. Second, a series of site investigation, including visual inspection, exploration pit, and geological penetrating radar, was employed to identify the deformation characteristics, appearance damage, and groundwater distribution. Third, the environmental factors were analyzed, and the spatio-temporal deformation characteristics were identified. Then the zoned numerical model was built to analyze the slope stability. Finally, the deformation mechanism and effect of treatment work were discussed. The results show that although the slope surface was replaced with a cement-treated weak expansive soil layer, the water vapor exchange between the undisturbed expansive soils and atmosphere is not completely isolated. The perched groundwater is also still replenished by precipitation infiltration. Groundwater, perched groundwater, long-large fissure and dense fissure zone induce the lateral creep deformation of the slope, and result in significant trend changes. The stability of the deformed body is in a critical state. The critical sliding surface is a broken line consisting of a gentle dip angle at the leading edge and a steep dip angle at the trailing edge. The depth of the potential sliding surface varies due to the geological condition and arrangement of anti-slide piles. Drainage wells can discharge deeper groundwater, thus can lower groundwater level and discharge perched groundwater. Supporting and unloading measures should also be taken to improve the slope stability.

Movements and habitat use of native and invasive piscivorous fishes in a temperate and channelized lowland river

AbstractLowland temperate rivers provide important habitats for piscivorous fishes, but with their year-round spatial and temporal habitat use is often poorly understood, including their use of off-channel habitats. Here, the movements and habitat use of the piscivorous native Northern pike Esox lucius and invasive pikeperch Sander lucioperca were investigated using acoustic telemetry in the highly regulated (through impoundment) lower River Severn, Western England over a 12-month period, where off-channel habitat availability was limited to a single boat marina. The movements of both species varied with season and temperature, with both species moving greater distances in spring. Increasing water temperatures up to 15 °C resulted in a higher frequency of movements of both species, but movements then decreased at temperatures higher than this. Northern pike detections in the river increased in periods of lower river discharge and warmer temperatures, with the off-channel refuge providing an important habitat all year round (78% of detections occurred there). While 63% of pikeperch detections also occurred in the marina, 89% of these detections occurred between December and April. These results thus emphasise the importance of this limited off-channel habitat as potential spawning locations for invasive pikeperch and foraging areas for native Northern pike.

Coupled two-dimensional model for heavily sediment-laden floods and channel deformation in a braided reach of the Lower Yellow River

It is difficult to predict the detailed morphodynamic processes induced by heavily sediment-laden floods in alluvial rives, due to the complexity in topography and the significant channel evolution rates, especially in a braided reach of the Lower Yellow River (LYR). A two-dimensional morphodynamic model using a coupled solution approach was firstly developed, with the effects of sediment concentration and bed deformation being directly considered in the hydrodynamic governing equations. The finite volume method with the HLL-MUSCL scheme was adopted in the numerical solution, which can obtain second-order accuracy in space and time. In addition, unstructured meshes were used to accommodate the irregular boundaries. The proposed model was validated using measurements in the braided reach of the LYR during the flood events of 2020 and 2004, with general agreement obtained between the calculated and measured hydrographs of flow and sediment concentration. The highest accuracy was achieved in the simulation of discharge, with a Nash-Sutcliffe efficiency coefficient (NSE) of 0.92. The simulation accuracy in sediment concentration was improved by the coupled approach, with the relative error of the calculated peak value decreasing from 17 % to 9 %. In addition, transport characteristics of graded suspended sediments were well simulated, with the fine fraction being transported downstream and the medium fraction depositing in the study reach. Influences of channel adjustments on the sediment transport processes were investigated during a flood event. The results demonstrated that the incised channel in 2020 was characterized by a larger water depth and smaller velocity, as compared with the shallow channel in 2004. Consequently, the peak discharge decreased and the flood propagation time was extended under the 2020 topography, associated with the lower sediment discharge at the outlet due to the reduced sediment transport capacity.

Strain Relaxation Characterization on Lithium‐ion Batteries at Different States of Charge and Charging Rates

The strain on the cell casing can serve as an indicator of the internal state of the cell. Monitoring strain during the charging and discharging processes aids in determining optimal charging and discharging operations, thereby maximizing the lifespan and performance of the battery. Herein, strain dynamic curves are obtained for lithium‐ion batteries at low, medium, and high charge and discharge rates by affixing strain gauges to individual cells. The investigation delves into parameters such as strain relaxation time, maximum strain, and residual strain at various charge rates and states of charge. The experimental findings reveal distinctive patterns, indicating that the strain curve during high‐rate charging resembles a second‐order function, exhibiting more pronounced fluctuations as the rate increases. This stands in stark contrast to the strain exponential decay observed during conventional medium and low‐rate charging. Notably, the strain residual resulting from high‐rate charging proves to be several times higher than that observed in low‐rate charging, hinting at potential differences in the dynamic distribution of lithium ions within batteries during high‐rate versus medium‐low‐rate charging modes.

Closed-loop cleaning treatment system — resource recovery of coal gangue

ABSTRACT Coal gangue (CG) is one of the main solid wastes emitted by coal mining. It causes severe damage to the environment. CG contains high levels of valuable elements (Al, Si) and has the potential for utilization and clean disposal. Here, an environment-friendly process for separating valuable components from CG was proposed: the closed-loop system of activation-leach-separation. The results show that the decarbonization rate was close to 100% under the optimum conditions of CG particle size of 0.075 mm to 0.15 mm and activated at 800°C for 120 min. Subsequently, it was transformed into a mixed-acid system with a hydrochloric acid (HCl) concentration of 4.5 mol/L, hydrofluoric acid (HF) volume fraction of 15%, and the liquid-solid ratio of 10:1, which achieved excellent separation efficiency. The residual rate of Al in the solution was only 0.7%, and the extraction rate of Si can reach 71.6%. Further, industrial-grade AlF3 products were also recovered. By adding saturated KCl solution and reacting at 33°C for 15 min, Si was further recovered in K2SiF6, and the yield was 85.83%. Particularly, the leaching solution maintained good extraction efficiency in the subsequent three cycles, the yield of K2SiF6 was 88.29%, confirming the feasibility of the closed-loop system. This treatment embodied the environmental-friendly properties of low acid consumption and low effluent discharge, providing a feasible method for clean treatment and resource utilization of CG.

Note on volume and distribution of fresh water in the Amazon River plume under low discharge conditions

In this research communication, we report the results of a field survey conducted in a part of the plume of the Amazon River between 0° and 5°N and offshore of the 28 m isobaths in November of 2022, during the low river discharge season. By comparing the observed vertical salinity profiles ‘disturbed’ by continental discharges within the plume with the virtually ‘undisturbed’ ones outside the plume, we estimated the total content of fresh water in the area covered by the measurements as 203 ± 22 km3, which equals to less than 3% of the average annual Amazon River discharge. Furthermore, we argue that the river-borne continental water was not confined to the upper mixed layer and show that about 37%, or 76 km3, of its volume was entrained into the plume-underlying layer between the mixed layer and the salinity maximum. This point is additionally supported by analysis of chromophoric dissolved organic matter (CDOM) fluorescence in water samples, demonstrating significant concentrations of terrigenous CDOM to depths up to 140 m. We also observed that there was a significant direct correlation between the volume of freshwater accumulated in the affected layer and background stratification (expressed as buoyancy frequency) in the unaffected layer below it.

Ecological risk assessment of heavy metals in desulfurized seawater discharged from a coal-fired power plant in Qingdao.

Despite the prevalence of discharge of large volumes of heavy-metal-bearing seawater from coal-fired power plants into adjacent seas, studies on the associated ecological risks remain limited. This study continuously monitored concentrations of seven heavy metals (i.e. As, Cd, Cr, Cu, Hg, Pb, and Zn) in surface seawater near the outfall of a coal-fired power plant in Qingdao, China over three years. The results showed average concentrations of As, Cd, Cr, Cu, Hg, Pb, and Zn of 2.63, 0.33, 2.97, 4.63, 0.008, 0.85, and 25.00 μg/L, respectively. Given the lack of data on metal toxicity to local species, this study investigated species composition and biomass near discharge outfalls and constructed species sensitivity distribution (SSD) curves with biological flora characteristics. Hazardous concentrations for 5% of species (HC5) for As, Cd, Cr, Cu, Hg, Pb, and Zn derived from SSDs constructed from chronic toxicity data for native species were 3.23, 2.22, 0.06, 2.83, 0.66, 4.70, and 11.07 μg/L, respectively. This study further assessed ecological risk of heavy metals by applying the Hazard Quotient (HQ) and Joint Probability Curve (JPC) based on long-term heavy metal exposure data and chronic toxicity data for local species. The results revealed acceptable levels of ecological risk for As, Cd, Hg, and Pb, but unacceptable levels for Cr, Cu, and Zn. The order of studied heavy metals in terms of ecological risk was Cr > Cu ≈ Zn > As > Cd ≈ Pb > Hg. The results of this study can guide the assessment of ecological risk at heavy metal contaminated sites characterized by relatively low heavy metal concentrations and high discharge volumes, such as receiving waters of coal-fired power plant effluents.

Holmium Laser Incision of Ejaculatory Duct (HoLIED): Surgical Procedure

Introduction: Ejaculatory duct obstruction is a well-known cause of infertility and many other symptoms, such as hematospermia and lower urinary tract symptoms. Diagnosis is made based on the medical history and a series of imaging tests identifying the obstructed ducts. Transurethral resection of the ejaculatory ducts is the mainstay treatment to release the obstruction. In this step-by-step surgical video, we will describe a novel technique using the holmium laser to incise the ejaculatory ducts in a patient with chronic lower urinary tract symptoms, hematospermia, and persistent urethral discharge. Materials and Methods: A pelvic MRI was obtained in workup of the above issues and identified a complex ejaculatory duct cyst. The patient consented for Holmium Laser Incision of Ejaculatory Duct. A holmium laser fiber was used through a 24F rigid cystoscope to unroof the ejaculatory duct cyst, resulting in the drainage of a dark brown fluid. Following unroofing of the cyst, the ejaculatory ducts were identified using a 17F rigid cystoscope and a 16F Foley catheter was inserted. Results: The Foley catheter was removed on POD1, and the patient was able to void. His symptoms improved progressively with time and antibiotics. A repeat MRI was obtained several months postoperatively and showed the resolution of the cystic lesion. Conclusion: Holmium Laser Incision of Ejaculatory Duct is safe and feasible procedure allowing to treat ejaculatory duct obstruction without increased risk of complications.

A 6-year Retrospective Study on the Clinical Profile and Outcomes of Postrenal Transplant Patients in the Emergency Department

Abstract Background: Kidney transplantation is widely recognized as the primary treatment for those with end-stage renal disease. Our goal was to provide an overview of the clinical characteristics of postrenal transplant patients (commercial vs. noncommercial) seeking care in the emergency department (ED). Methodology: The study was conducted at a leading Omani ED from 2015 to 2021; this study included all postrenal transplant patients. Various variables were categorized, coded, and analyzed. Results: A total of 55 postrenal transplant patients were included in our study. Of these, 60.0% were male (n = 33). Among the participants, 14.5% (n = 8) had undergone noncommercial renal transplants, whereas the remaining 85.5% (n = 47) had undergone commercial renal transplants. Among noncommercial postrenal transplant patients, the most common reasons for ED visits were fever (5), gastrointestinal symptoms (4), and cardiac symptoms (3). They also presented with pain at the surgical site (2) and urological symptoms such as dysuria and hematuria (2). In contrast, the most frequent clinical presentations among commercial postrenal transplant patients were cardiac symptoms (13) and pain at the surgical site (13), followed by fever (12). Noncommercial renal transplant patients had a high discharge rate of 62.5% (5) and a low admission rate of 37.5% (3). On the other hand, commercial renal transplant patients necessitated a high admission rate of 59.6% (28) and a low discharge rate of 40.4% (19). Conclusion: The majority of patients had received commercial kidney transplants, and the most common complaints upon their presentation to the ED were cardiac symptoms and pain at the surgical site. Patients undergoing commercial transplants had higher rates of admission.

Performance of pulsed plasma thruster at low discharge energy

As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster (PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at 2 J or more of discharge energy. In this work, the performance of a PPT with a side-fed, tongue-flared electrode configuration operated within a lower discharge energy range of 0.5‒2.5 J has been investigated. Ablation and charring of the polytetrafluoroethylene propellant surface were analyzed through field-effect scanning electron microscopy imaging and energy-dispersive X-ray spectroscopy. When the discharge energy fell below 2 J, inconsistencies occurred in the specific impulse and the thrust efficiency due to the measurement of the low mass bit. At energy 2 J, the performance parameters are compared with other PPT systems of similar configuration and discussed in depth.