Linear Range Research Articles

A novel electrochemical sensor based on aspartic acid polymer and carbonized-ZIF-67 for rapid sensing of arbutin

A novel electrochemical sensor modified by aspartic acid polymer and carbonized-ZIF-67 was prepared for arbutin detection. ZIF-67 was synthesized and carbonized, and then used as the substrate supporting of electrochemical sensor. Carbonized-ZIF-67 had a large specific surface and good electrical conductivity, which provided large electroactive area and promoted the electron transfer at the sensing interface. Aspartic acid polymer was prepared by cyclic voltammetry. Aspartic acid polymer could effectively absorb arbutin, resulting in the preconcentration of arbutin on sensor surface. Benefiting from the synergistic effect between carbonized-ZIF-67 and aspartic acid polymer, the prepared electrochemical sensor exhibited sensitive electrochemical response for arbutin. Under the optimum conditions, the electrochemical sensor achieved a wide linear range in the range from 5 to 110 μmol/L and a low detection limit of 0.41 μmol/L for arbutin. In practical application, the electrochemical sensor was employed to detect arbutin in green tea and whitening cream samples, exhibiting satisfactory recovery rates. With the outstanding features of easy operation, rapid response and high sensitivity, the prepared electrochemical sensor provided a convenient and effective tool for arbutin detection.

“Green mathematical approaches in fluorescence spectroscopy for quality control and clinical studies”

In the past decade, significant advancements have been made in mathematical spectral approaches for estimating binary and ternary drug combinations in raw materials and dosage forms. These approaches established on mathematical spectral manipulations of mixture analytes, without the need for separation techniques.The idea of using mathematical spectral approaches in fluorescence spectroscopy was resolving analytical issues and reach to biological concentrations thus, Ratio subtraction (RD) and ratio subtraction coupled with constant multiplication (RS-CM) have been proposed in fluorescence spectroscopy to evaluate the content uniformity of Flunarizine dihydrochloride (FLZ) and Propranolol hydrochloride (PRO) combination in raw materials, tablets, and spiked biological fluids (blood-urine). These approaches have demonstrated the ability to overcome the quantitative analytical challenges posed by the high native fluorescence intensity of the major component (PRO) at λex = 286/λem = 341 nm and the low native fluorescence intensity of the minor component (FLZ) at λex = 254/λem = 311 nm. The linearity range for (PRO) was found to be 25–500 ng/mL, and for (FLZ), it was 50–500 ng/mL. However, the spectrum addition technique was required to estimate (FLZ) in mixtures with concentrations less than 300 ng/mL.The overall validity of the proposed approaches was confirmed through adherence to ICH guidelines, and no statistical variation was observed in comparison to official studies. Additionally, the greenness and whiteness of the proposed approaches were evaluated using the Analytical greenness metric (AGREE), Green Solvents Selecting Tool (GSST), and Red-Green-Blue (RGB) algorithm.

Sustainable and technically smart spectrophotometric determination of PAXLOVID: a comprehensive ecological and analytical performance rating

The Food and Drug Administration (FDA) authorized the administration of ritonavir (RIT)-boosted nirmatrelvir (NMV) on May 25, 2023, for the treatment of mild to moderate COVID-19 in patients who are at high risk of developing severe COVID-19. In accordance with sustainability and environmental friendliness, simple, eco-friendly, and sustainable spectrophotometric methods were established for concurrently estimating RIT and NMV in newly launched copackaged pills. The suggested solutions for resolving the spectral overlap between RIT and NMV involve the following mathematical methods: the first derivative method (1D), second derivative method (2D), and dual-wavelength zero-order method (DWZ). When ethanol was used as a green dilution solvent, the linearity range was adjusted (10–250 µg/mL) for both drugs. The procedures resulted in a high correlation coefficient (not less than 0.9996) and satisfactory levels of detection and quantification. Additionally, method validation was performed in accordance with International Council for Harmonization norms. Moreover, a detailed ecological and sustainability evaluation protocol was established to confirm the greenness and whiteness of the methods. Finally, the proposed method, along with previously reported methods for analysing NMV and RIT, were reviewed analytically and ecologically.

Determination of tetramethylammonium hydroxide in air using ion chromatography or ultra-performance liquid chromatography - high-resolution mass spectrometry

Tetramethylammonium hydroxide (TMAH) is extensively utilized in the semiconductor and optoelectronic industries, serving as either a developer or an etchant. TMAH possesses acute toxicity and alkaline corrosiveness, having caused several fatal and injurious accidents in Taiwan. However, there is currently a lack of methods available for assessing TMAH exposure. This study developed a method involving sampling with quartz fiber filters followed by ultrasonic agitation in 10 mL mobile phase, filtering, and analysis using either ion chromatography (IC) or ultra-performance liquid chromatography - high-resolution mass spectrometry (UPLC-HRMS). Utilizing the characteristics of HRMS, the compound analyzed was identified as tetramethylammonium ion (TMA+) through mass spectrometry analysis. The method exhibits excellent trapping capacity and recovery rate. The linear range of TMA+ for IC is 0.3 to 100 μg/mL, with a correlation coefficient of R = 0.9998. The linear range of TMA+ for UPLC-HRMS is 0.002 to 1 μg/mL, with a correlation coefficient of R = 0.996. The recovery rates for IC and HRMS were 116.6% and 90.6%, with corresponding coefficient of variation (CV) of 2.25% and 3.53%, respectively. Samples can be stored at room temperature for 28 days. Verification of this method was conducted at the TMAH factory, and the air concentrations measured in the TMAH filling area were 3.29 and 4.75 μg/m3 from IC and UPLC-HRMS, respectively. This method will be applied in the on-site analysis of occupational hazards for operators in chemical plants, technology factories, and recycling plants, aiming to evaluate risk values to protect the safety and health of workers and prevent occupational diseases.

“Eco-friendly HPLC method for analysis of dipyrone and hyoscine in different matrices with biomonitoring”

A selective, precise, and accurate reversed HPLC method has been developed and validated for simultaneous separation and determination of two veterinary drugs, dipyrone and hyoscine, in their combined dosage form in the presence of their official impurities, namely 4-aminoantipyrine and tropic acid, in addition to the formulated preservative: phenol. The linearity range was found to be (1.00–35.00 µg/mL) for dipyrone and (2.50–50.00 µg/mL) for hyoscine. It exhibited a satisfactory linearity regression R (0.9999) for both drugs with LOD 0.22 µg/mL and 0.72 µg/mL and LOQ 0.65 µg/mL and 2.19 µg/mL for dipyrone and hyoscine, respectively. Additionally, the two cited drugs were also determined in the presence of dipyrone active metabolite 4-aminoantipyrine using diclofenac as an internal standard in bovine urine. The linearity range was found to be (15–75 µg/mL) for dipyrone, (2.5–60 µg/mL) for hyoscine, and (2.5–60 µg/mL) for 4-aminoantipyrine with linearity regression R (0.9999–0.9998). The LLOQ (15, 2.5, 2.5 µg/mL), LQC (45, 7.5, 7.5 µg/mL), MQC (55, 25, 25 µg/mL), and HQC (60, 50 50 µg/mL) were determined for dipyrone, hyoscine and 4-aminoantipyrine, respectively. UV detection was carried out at 220 nm. The method was validated according to the ICH guidelines, as well as according to FDA guidelines for determining both drugs in bioanalytical matrices and both proved accuracy and precision. A statistical comparison was made between the results obtained and those obtained by the reported method, showing no significant difference in accuracy and precision at p = 0.05. The suggested method was proved eco-friendly through a greenness assessment using two different tools (The analytical eco-scale scored 83, and the AGREE-Analytical Greenness Metric approach scored 0.83). The suggested method can be used in the routine work of quality control labs, screening for drug abuse, and ensuring clean sport for horse racing.

Quantification of morphine in exhaled breath condensate using a double network polymeric hybrid hydrogel functionalized with AuNPs

BackgroundMorphine serves as a foundation for creating other opioid derivatives, such as hydro/oxymorphine and heroin, which possess enhanced pain-relieving properties but are also prone to addiction and abuse. In cases of morphine overdose, it not only affects multiple immune functions but can also cause severe health complications. Given these concerns and the widespread use of morphine, it is crucial to develop efficient, uncomplicated, and precise methods for accurately detecting morphine in various biological and pharmaceutical samples.ResultsIn this investigation, a novel gold nanoparticle (AuNPs)-based double network hydrogel (DNH) nanoprobe has been fabricated for sensitive quantification of morphine in exhaled breath condensate samples. For that, gelatin/agarose DNH was fabricated through a one-step heating-cooling method in the presence of AuNPs, providing not only chemical stability but also prevent the AuNPs aggregation during synthesis process. In this method, the absorbance intensity of the nanoprobe gradually decreased with increasing morphine concentration due to the interaction morphine with AuNPs surface plasmon. The aggregation of AuNPs by addition of morphine was verified by UV-Vis spectrophotometry. The sensor displayed high sensitivity with detection limit of 0.006 µg.mL-1 in the linear range from 0.01 to 1.0 µg.mL-1. A reliable performance was attained for the spectrophotometric method for determination of morphine in the real samples.

Flexible Tactile Sensors with Gradient Conformal Dome Structures.

The trade-off between high sensitivity and wide detection range remains a challenge for flexible capacitive pressure sensors. Gradient structure can provide continuous deformation and lead to a wide sensing range. However, it simultaneously augments the distance between two electrodes, which diminishes the variation in the relative distance and results in a decreased sensitivity. Herein, a conformal design is introduced into the gradient structure to construct a flexible capacitive pressure sensor. The gradient conformal dome structure is fabricated by a simple reverse dome adsorption process. Taking advantage of the progressive deformation behavior of the gradient dielectric, and the significant improvement of relative distance variation between two electrodes from the conformal design, the sensor achieves a sensitivity of 0.214 kPa-1 in an ultrabroad linear range up to 200 kPa. It maintains high-pressure resolution under the preload of 10 and 100 kPa. Benefiting from the rapid response and excellent repeatability, the sensor can be used for physiological monitor and human motion detection, including arterial pulse, joint bending, and motion state. The gradient conformal design strategy may pave a promising avenue to develop pressure sensors with high sensitivity and wide linear range.

Ultrasensitive Electrochemical Biosensors Based on Allosteric Transcription Factors (aTFs) for Pb2+ Detection

Exposure to Pb2+ in the environment, especially in water, poses a significant threat to human health and urgently necessitates the development of highly sensitive Pb2+ detection methods. In this study, we have integrated the high sensitivity of electrochemical techniques with allosteric transcription factors (aTFs) to develop an innovative electrochemical biosensing platform. This biosensors leverage the specific binding and dissociation of DNA to the aTFs (PbrR) on electrode surfaces to detect Pb2+. Under the optimal conditions, the platform has a broad linear detection range from 1 pM to 10 nM and an exceptionally low detection threshold of 1 pM, coupled with excellent selectivity for Pb2+. Notably, the biosensor demonstrates regenerative capabilities, enabling up to five effective Pb2+ measurements. After one week of storage at 4 °C, effective lead ion detection was still possible, demonstrating the biosensor’s excellent stability, this can effectively save the cost of detection. The biosensor also achieves a recovery rate of 93.3% to 106.6% in real water samples. The biosensor shows its potential as a robust tool for the ultrasensitive detection of Pb2+ in environmental monitoring. Moreover, this research provides new insights into the future applications of aTFs in electrochemical sensing.

Ultrasensitive Electrochemiluminescence Biosensor with ZIF-67@MXene as an Efficient Co-Reaction Accelerator and Plasmonic Nanozyme as a Smart Signal Amplification Probe.

Exploring novel electrochemiluminescence (ECL) co-reaction accelerators to construct ultrasensitive sensing systems is a prominent focus for developing advanced ECL sensors. However, challenges still remain in finding highly efficient accelerators and understanding their promoting mechanisms. In this paper, ZIF-67@MXene nanosheet composites, with highly conductive in-plane structure and confined-stable pore/channel, are designed to act as high-efficient co-reaction accelerators and achieve a significant enhancement in the luminol-H2O2 based ECL system. Mechanism investigation suggests that hydroxyl radicals (·OH) and singlet oxygen (1O2) can be selectively and preferentially generated on ZIF-67@MXene due to the stable and efficient absorption of ·OH and 1O2, leading to a remarkable enhancement in the ECL efficiency of luminol (830%). Finally, by designing a plasmonic NH2-MIL-88@Pd nanozyme, an "on-off" switch immunosensor is constructed for the detection of prostate-specific antigen (PSA). Based on the multiple signal amplification effect, the linear detection range for PSA is expanded by three orders of magnitude. The detection limit is also improved from 1.44 × 10-11 to 9.1 × 10-13 g mL-1. This work proposes an effective method for the preparation of highly efficient co-reaction accelerators and provides a new strategy for the sensitive detection of cancer markers.

Preparation and application of a pseudo-templated multi-monomer aflatoxins imprinted polymer.

Afunctional material was developedwith specific recognition properties for aflatoxins for pre-processing enrichment and separation in the detection of aflatoxins in Chinese herbal medicines. In the experiment, ethyl coumarin-3-carboxylate, which has a highly similar structure to the oxonaphthalene o-ketone of aflatoxin, was selected as a pseudo-template, zinc acrylate, neutral red derivative, and methacrylic acid, which have complementary functions, were selected as co-monomers to prepare a pseudo-template multifunctional monomer molecularly imprinted polymer (MIP). The MIP obtained under the optimal preparation conditions has a maximum adsorption capacity of 0.036mg/mg and an imprinting factor of 3.67. The physical property evaluation of the polymers by Fourier infrared spectrometer, scanning electron microscopy, pore size analyzer, thermogravimetric analyzer, and diffuse reflectance spectroscopy showed that the MIP were successfully prepared and porous spherical-like particles were obtained. The synthesized polymer was used as a solid-phase extraction agent for the separation of aflatoxins from the extract of spina date seed. The linear range of the developed method was 10-1000ng/mL, the limit of detection was 0.36ng/mL, the limit of quantification was1.19ng/mL, and the recoveries of the extracts at the concentration level of 0.2μg/mL were in the range 88.0-93.4%, with relative standard deviations (RSDs) of 1.97% (n). The results showed that the preparation of MIPs using ethyl coumarin-3-carboxylate as a template was simple, economical, and convenient. It is expected to become a promising functional material for the enrichment and separation aflatoxins from complex matrices.

An ultra-sensitive suboptimal protospacer adjacent motif enhanced rolling circle amplification assay based on CRISPR/Cas12a for detection of miR-183

IntroductionMicroRNAs (miRNAs) have been recognized as promising diagnostic biomarkers for Diabetic Retinopathy (DR) due to their notable upregulation in individuals with the condition. However, the development of highly sensitive miRNAs assays for the rapid diagnosis of DR in clinical settings remains a challenging task.MethodsIn this study, we introduce an enhanced CRISPR/Cas12a assay, leveraging suboptimal PAM (sPAM)-mediated Cas12a trans-cleavage in conjunction with rolling circle amplification (RCA). sPAM was found to perform better than canonical PAM (cPAM) in the detection of Cas12a-mediated ssDNA detection at low concentrations and was used instead of canonical PAM (cPAM) to mediate the detection. The parameters of reactions have also been optimized.Results and discussionIn comparison with cPAM, sPAM has higher sensitivity in the detection of ssDNA at concentrations lower than 10 pM by Cas12a. By replacing cPAM with sPAM in the padlock template of RCA, ultra-high sensitivity for miR-183 detection is achieved, with a detection limit of 0.40 aM. within 25 min and a linear range spanning from 1 aM. to 1 pM. Our assay also exhibits exceptional specificity in detecting miR-183 from other miRNAs. Furthermore, the applicability of our assay for the sensitive detection of miR-183 in clinical serum samples is also validated. This study introduces a groundbreaking assay with excellent performance through a simple modification, which not only addresses existing diagnostic challenges, but also opens exciting new avenues for clinical diagnosis in the realm of DR.

Schottky Interface Enabled Electrospun Rhodium Oxide Doped Gold for Both pH Sensing and Glucose Measurements in Neutral Buffer and Human Serum.

This study has focused on adjusting sensing environment from basic to neutral pH and improve sensing performance by doping electrodeposited gold (Au) with metal oxide for nonenzymatic glucose measurements in forming a Schottky interface for superior glucose sensing with detailed analysis for the sensing mechanism. The prepared sensor also holds the ability to measure pH with the identical electrospun metal oxide-electrodeposited Au, which composed a dual sensor (glucose and pH sensor) through applying chronoamperometry and open circuit potential methods. The rhodium oxide nanocoral structure was fabricated with an electrospinning precursor solution, followed by a calcination process, and it was mixed with electrodeposited nanocoral gold to form the Schottky interface by constructing a p-n type heterogeneous junction for improved sensitivity in glucose detection. The prepared materials were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectrometry (XPS), etc. The prepared materials were used for both pH responsive testing and amperometric glucose measurements. The rhodium oxide nanocoral doped gold demonstrated a sensitivity of 3.52 μA mM-1 cm-2 and limit of detection of 20 μM with linear range up to 3 mM glucose concentration compared to solely electrodeposited gold for a sensitivity of 0.46 μA mM-1 cm-2 and a limit of detection of 450 μM. The Mott-Schottky method was used for the analysis of an electron transfer process from noble metal to metal oxide to electrolyte in demonstrating the improved sensitivity at neutral pH for glucose measurements due to the Schottky barrier adjustment mechanism at an applied flat band potential of 0.3 V. This work opens a new venue in illustrating the metal oxide/metal materials in the glucose neutral response mechanism. In the end, human serum samples were tested against current commercial glucose meter to certify the accuracy of the proposed sensor.

In Situ Photoelectrodeposited Polyaniline on Ti‐Doping Hematite For Highly Selective Photoelectrochemical Oxygen Demand Determination

AbstractChemical Oxygen Demand (COD), as a detection indicator of water pollution, is of particular importance in assessing organic pollution in water. Furthermore, accurate and simple measuring COD methods are essential for water quality assessment and pollution control. However, the photoelectrochemical oxygen demand (PECOD) measurement, as one of the measuring COD methods, is affected by the reaction of water splitting, which is one of the hindrances to the commercialization of the analytical method of the PeCOD measurement. Hence, to overcome this challenge, a new PANI/Ti:Fe2O3 photoanode is constructed by hydrothermal and photoelectrochemical (PEC) deposition methods and investigated their optical properties and photoactivity. Under optimization conditions, it is discovered that the oxidation of organic compounds produces a net steady‐state current (inet) is directly proportional to COD concentration, with a detection limit of 1 mM glucose solution and a wide linear detection range of 1–78.125 mM, which is suitable for high concentration of glucose detection. As has been noted, PANI/Ti:Fe2O3 photoanode overcomes the obstacles to the practical application and eventual commercialization of the PECOD technology.

Molecular imprinting based sensor system developed using polymeric nanoparticles for detecting 17β‐estradiol in agricultural wastewater

AbstractMicro pollutants pose a significant issue in water ecosystems. Particularly high concentrations of 17β‐estradiol (E2) have been identified in agricultural wastewater, which poses harmful effects on aquatic organisms and disrupts ecosystem balance. Therefore, effective determination of E2 from water sources is crucial. This study developed a biosensor capable of detecting E2 in wastewater using specific polymer nanoparticle synthesis through molecular imprinting. Est‐imp‐poly(multi‐walled carbon nanotubes‐glycidyl methacrylate [MWCNT‐GMA]) polymer nanoparticles were synthesized using a surfactant‐free emulsion polymerization method, and their characterization was conducted using FTIR and scanning electron microscopy (SEM) technologies. The Qmax value for Est‐imp‐poly(MWCNT‐GMA) nanoparticles in a 1 mg/mL E2 solution was determined to be 140 ppm. Comparing adsorption capacities, the molecularly imprinted nanoparticles (MIP) showed nearly five times higher E2 adsorption compared to non‐imprinted polymers (NIP). The Est‐imp‐poly(MWCNT‐GMA)‐Nafion/screen‐printed electrode (SPE) system was employed for analyzing wastewater samples. The current measurements taken at various concentrations in the wastewater consistently matched the E2 concentration calibration curve. The limit of detection (LoD) and limit of quantification (LoQ) were determined to be 0.042 and 0.12 μM, respectively. The biosensor demonstrated a linear working range from 0.12 to 50 μM, with a high correlation coefficient (R2 = 0.9927). These results highlight the potential of the developed biosensor for detecting E2 in real samples.

Biosensor Based on ZIF-67-HRP and MWCNTs Nanocomposite Modified Glass Carbon Electrode for the Detection of Luteolin in Vegetables.

Luteolin has various pharmacological properties, including anti-inflammatory, antioxidant, and antitumor characteristics. Due to its potential value in drugs and functional foods, it is important to develop an efficient method for detecting luteolin. In this work, the poor selectivity of existing luteolin nonenzymatic sensors was solved by translating the enzyme-catalyzed reaction from bulk solution to the surface of a horseradish peroxidase (HRP) modified electrode through an electrocatalytic oxidation process. Here, we modified the surface of a glassy carbon electrode (GCE) with metal-organic frameworks (MOFs; ZIF-67 here, abbreviated as ZIF), functional nanomaterials, and HRP and finally covered it with Nafion (NF). In this case, luteolin acts as a hydrogen donor, and the electrode acts as a hydrogen acceptor; the oxidation reaction occurs on the electrode surface. The use of ZIF-67 ensured the conformational stability of HRP to ensure the selectivity and anti-interference property, and SDS-dispersed multiwalled carbon nanotubes (MWCNTs) enhanced the electrode conductivity. The use of NF avoids shedding of the electrode material during the testing process. A UV-vis spectrophotometer was used to study the selectivity of luteolin by HRP and the compatibility between HRP and ZIF. The materials were characterized and analyzed by scanning electron microscopy and transmission electron microscopy. Due to the synergistic effect of these nanomaterials, the linear range of NF/ZIF-HRP/MWCNTs-SDS/GCE was 1.0 × 10-2 to 6.0 μM, with detection limits of 25.3 nM (S/N = 3). The biosensor showed long-term stability and reproducibility, with a relative standard deviation of 4.2% for the peak current (n = 5). Finally, the biosensor was successfully used to detect luteolin in carrots, celery, and cauliflower.

Fluorescent and polarity-switchable photoelectrochemical dual-mode homogeneous sensing platform for ultrasensitive kanamycin detection based on EXO III-driven signal amplification.

Afluorescent and photoelectrochemical (PEC) dual-mode biosensor based on target biorecognition-triggered cyclic amplification was constructed for Kana detection. With the assistance of the catalyzed reaction of exonuclease III, a Kana-aptamer DNA duplex was designed for conducting the cyclic release of G-rich DNA sequence as well as output DNA S2. The released G-rich sequence triggers the fluorescence (FL) of thioflavin T (ThT), the intensity of which is positively correlated with the Kana concentration. The linear range is 0.2 to 30nM, and the detection limit reaches 0.07nM. Simultaneously, the released output DNA S2 was captured by Fe3O4@CdTe-probe ssDNA and then combined with methylene blue to realize the transduction of polarity-reversed PEC signal, leading to the sensitive detection of Kana with a linear range of 0.2 to 40nM and a calculated detection limit of 0.2nM. The outstanding performance endows the dual-mode biosensor a promising prospect for practical application.

A silicon-based functional self-assembled aptasensor for the detection of aflatoxin B1 by SERS sensing.

One of the most harmful contaminants found in corn and its products is aflatoxin B1 (AFB1) and thus developing reliable detection methods is of great significance to consumers and the food industry. In this research, AuMBA@Ag nanoparticles (NPs) and AgNPs deposited on a silicon wafer (Si@AgNPs) were functionalized with an aptamer and its complementary strand, respectively, and self-assembled into a SERS aptasensor, which generated strong SERS signals. AFB1 bound to the aptamer prior to the complementary chain, causing AuMBA@Ag NPs to detach from Si@AgNPs. The complex dissociated, leading to a decrease in signal intensity from the solid-phase substrate. Under optimal conditions, the linear detection range was 0.05-20.0 ng mL-1, and the detection limit was 0.039 ng mL-1. Notably, the aptasensor demonstrated a recovery rate between 92.77% and 110.13% when utilized for the detection of AFB1 in corn flour and oil, indicating its good potential for detecting AFB1 in real sample matrices. In conclusion, a quantitative and reliable specific SERS detection system for AFB1 was developed in this study with significant applicability to food safety.

A glutathione-activatable near-infrared fluorescent probe with a large Stokes shift for imaging 4T1 tumor and its ferroptosis

Some tumor cells have higher concentrations of glutathione (GSH) compared to normal cells, and ferroptosis can result in a significant decrease of GSH level in tumor cells. Thus, GSH can be employed as the biomarker for imaging some tumors and their ferroptosis. In this article, a GSH-activatable near-infrared fluorescent probe (QL-NF) with a large Stokes shift (110 nm) was developed for imaging 4T1 tumor and its ferroptosis. QL-NF employs the quinolinium-xanthene dye as the fluorophore and the 2-fluoro-4-nitrobenzene-1-sulfonate group as the response unit for GSH. QL-NF has a high selectivity and an applicable linear response range (0.50 mM–10.00 mM) for physiological GSH. Moreover, QL-NF was successfully used for imaging GSH in cancer cells and monitoring the concentration fluctuations of GSH during ferroptosis of cancer cells. Finally, QL-NF was further successfully employed for imaging 4T1 tumor and its ferroptosis in mice. All these results demonstrate that QL-NF is a useful tool for detecting GSH in vivo and imaging tumor ferroptosis, which is helpful for understanding tumor ferroptosis and further promoting the treatment of tumor.

A double-conducting polymer nanowire-based electrochemical aptasensor for highly sensitive and low fouling detection of cortisol in saliva.

Acortisol biosensor was developedbased on double-conducting polymer nanowires, which exhibits excellent conductivity, resistance to biological contamination, and outstanding sensing performance. The biosensor employs dual-mode electrochemical techniques, namely, differential pulse voltammetry (DPV) and chronoamperometry (CA), for the sensitive and low fouling detection of the glucocorticoid hormonecortisol. Experimental results demonstrated that the linear detection range of the biosensor in DPV mode was 1.0 × 10-14-1.0 × 10-8M, with a detection limit of 0.131 × 10-14M. In CA mode, the biosensor exhibited a detection range of 1.0 × 10-13-1.0 × 10-7M and a detection limit of 0.313 × 10-13M. The biosensor was successfully utilized for the rapid detection of cortisol in human saliva. The combination of a high-specificity cortisol aptamer and functionalized double-conducting polymer nanowires ensured the exceptional specificity and sensitivity of the biosensor in detecting real biological samples.

One-step hydrothermal synthesis of F,N,S-doped photoluminescent carbon dots with yellowish-orange emission for sensitive Cu2+ ion detection: Environmental and biomedical applications

Herein, fluorine-, nitrogen-, and sulfur-doped carbon dots (FNS-CDs) were prepared via a one-step hydrothermal synthesis using flufenamic acid and thiourea as precursors, which showed yellowish-orange fluorescence both in aqueous solution and in the solid state. The as-prepared FNS-CDs were monodisperse and had an average diameter of 4 nm, good water solubility, a fluorescence quantum yield of 18.63 %, and excellent pH and ionic strength stability. The optimal excitation/emission wavelengths of the FNS-CDs were 406/570 nm, with an excitation-dependent wavelength range of 365–435 nm. The surface states, morphologies, and elemental compositions of the FNS-CDs were characterized using FTIR, XRD, TEM, and XPS. In addition, the FNS-CDs without any further modification exhibited high selectivity and sensitivity as nanosensors for Cu2+ over other metal ions. The PL quenching phenomenon can be used to detect Cu2+ ions within a linear range of 1–25 μM with a detection limit of 83.10 nM and an association constant of 1.29 × 104 M−1. The PL of the FNS-CDs was significantly quenched by Cu2+ ions through static quenching and was restored upon the subsequent addition of EDTA. The practical application was demonstrated through the detection of Cu2+ ions in real water samples, yielding recovery rates ranging from 97.8 % to 103.9 % with an RSD below 2.5 %. The FNS-CDs/Cu2+ complex exhibits potent antibacterial activity against S. aureus (85.27 %±2.1 %) and E. coli (91.31 %±1.6 %), whereas the FNS-CDs/Cu2+ has a higher inhibitory effect on the growth of E. coli. Furthermore, the FNS-CDs (100 μg/mL) were used for cell imaging, showing low toxicity to HCT-116 cells exhibited yellowish-orange fluorescence under a confocal microscope.