Ionic Liquid Pretreatment Research Articles

Imidazole ionic liquid effects on coal swelling behavior and pyrolysis characteristics: Experiment and molecular simulation

In view of low-rank coal conventional swelling solvent large pollution and the clean efficient utilization of coal, the effects of imidazole ionic liquid (IL) pretreatment with different anion groups as green solvent on coal thermal expansion and pyrolysis performance were investigated. IL interacts with coal molecules, destroying the hydrogen bonds, resulting coal expansion. Different anion groups have different modification effects, [Bmim]Cl has the best swelling effect, which is 17.37 % higher than raw coal, and the best modification time is 24 h. In addition, IL modification has a catalytic effect on coal pyrolysis, which can significantly reduce the maximum weight loss temperature and increase tar content. Coal solvent pretreatment provides a good theoretical basis for application of swelling and pyrolysis. The reduction of thermochemical reaction temperature not only reduces the content of heavy groups in pyrolysis products, but also provides new ideas for carbon emission reduction.

Current status and future prospects of pretreatment for tobacco stalk lignocellulose.

With the growing demand for sustainable development, tobacco stalks, as a resource-rich and low-cost renewable resource, hold the potential for producing high-value chemicals and materials within a circular economy. Due to the complex and unique structure of tobacco stalk biomass, traditional methods are ineffective in its utilization, making the pretreatment of tobacco stalk lignocellulose a crucial step in obtaining high-value products. This paper reviews recent advancements in various pretreatment technologies for tobacco stalk lignocellulosic biomass, including hydrothermal, steam explosion, acid, alkaline, organic solvent, ionic liquid, and deep eutectic solvent pretreatment. It emphasizes the impact and efficiency of these pretreatment methods on the conversion of tobacco stalk biomass and discusses the advantages and disadvantages of each technique. Finally, the paper forecasts future research directions in the pretreatment of tobacco stalk lignocellulose, providing new insights and methods for enhancing its efficient utilization.

Hydrolysis of Babool wood biomass using carbocation scavengers assisted ionic liquid pretreatment for the production of sugars and furfurals

The present study highlights the performance of carbocation scavengers for the pretreatment of hardwood biomass followed by the production of bio-based products. The behaviour of different carbocation scavengers namely; 2-Napthol, 4 Hydroxybenzoic acid, Vanillic acid, Catechol, Hydroquinone, Resorcinol and Phenol and their mitigating effect on the rate of hydrolysis was explored under different operating conditions. All the carbocation scavengers show significant changes in the crystallinity index leading to distinct morphological and physiochemical changes in the biomass structure. Results revealed that the addition of carbocation scavengers not only reduces the inhibitory effect of structured lignin but also enhances the accessibility of cellulose and hemicellulose and facilitates the production of sugars and 5-Hydroxymethyl Furfural. Maximum 5-HMF yield was observed using 2-Napthol at an optimised concentration of 2 wt% (1.5 mL) at 190 °C in 60 min. Further, to evaluate the effect of acetyl groups, biomass deacetylation was also performed. The highest deacetylation effect was observed at 170 °C and showed ∼73% and ∼94% reduction in the holocellulosic content in 60 min. The proposed study develops a sustainable and viable route to suppress the inhibitory effect of lignin with the utilization of carbocation scavengers and enhances biomass digestibility that favours the production of bio-based chemicals.

Ionic liquid pretreatment of lignocellulose for complete hemicellulose removal to produce high-purity cellulose mixed esters

Strategic valorization of agricultural waste can serve as waste management and promote sustainable biorefineries. Sugarcane bagasse is a readily available lignocellulosic biomass and can be converted into valuable cellulose-based thermoplastics. However, the cellulose purity significantly influences the material properties of the resulting thermoplastics, potentially limiting their applications. Therefore, conventional production necessitates harsh pretreatment of lignocellulose to isolate high-purity cellulose, followed by chemical modification. Here, we demonstrate a facile and green pretreatment method for complete removal of hemicellulose by incubating bagasse in a mixed system of an ionic liquid, 1-ethyl-3-methylimidazolium acetate (EmimOAc), and dimethyl sulfoxide (DMSO) at 140 °C, followed by precipitation in water, achieving >99 % hemicellulose removal. The pretreated bagasse, containing 71 % cellulose and 28 % lignin, underwent homogeneous transesterification with vinyl decanoate and isopropenyl acetate, using EmimOAc as both the solvent and catalyst, assisted by a co-solvent of DMSO. The polysaccharide derivative in the resulting acylated bagasse was separated from the lignin derivative by precipitation in methanol. The obtained polysaccharide derivative with high cellulose purity displayed a high weight-average molar mass of 1.5×106 g mol−1 and a polydispersity of 4. It also exhibited superior thermal stability (thermal degradation temperature, Td−5 %: 359 °C; glass transition temperature, Tg: 144 °C) compared to pulp-derived cellulose acetate decanoate (Td−5 %: 349 °C; Tg: 129 °C).

RETRACTED: Green and efficient synthesis of cellulose nanocrystals from Hamelia patens leftover via hydrolysis of microwave assisted-ionic liquid (MWAIL) pretreated microcrystalline cellulose

The efficient bioconversion of the lignocellulosic agro-waste has immense importance in biorefinery processing in extracting the cellulose and saccharide fractions. To achieve this, a series of chemical pretreatments is employed, thus concerning environmental threats limit its use. Therefore, an ionic liquid is employed for pretreatment before sustainable extractions owing to its safe manipulation, recycling, and reusability. Specifically, microwave-assisted ionic liquid (MWAIL) pretreatment has significant importance in extracting high cellulose yield at less thermal power consumption. In this study, the leftover stalks of Hamelia patens were subjected to MWAIL pretreatment at 60, 70, 80, and 90 °C to extract microcrystalline cellulose (MCC). Subsequently, the MCC was fabricated into cellulose nanocrystals (CNC) through hydrolytic treatment using acidic and ionic liquids and denoted as CNC-AH and CNC-ILH. Thus obtained CNC was characterized by FTIR, FESEM, XRD, and TGA to investigate the influence of solvent on its morphology, crystallinity, and thermal stability of CNC. The results support that the CNC-ILH has comparatively more thermal and dispersal stability with a reduced crystallinity index than CNC-AH. The surprising results of CNC-ILH signify its utilization in diverse applications in the food and industrial sectors.

Valorization of Afzelia bella oilseeds cake in bioethanol production using 1-butyl-3-methyl-imidazolium chloride ionic liquid and dilute sulfuric acid pretreatment

The use of renewable feedstocks and the variability of lignocellulosic feedstocks generating fermentable sugars also offer the advantages of the most abundant, sustainable and competitive non-food biomass. The aim of this study is to valorize the oilcake obtained from non-conventional Congolese Afzelia bella oilseeds, after extraction of the oil used in biodiesel production. The conversion of A. bella oilseeds cake into ethanol was carried out using the two methods of pretreatment (with the synthesized ionic liquid 1-butyl-3-methyl imidazolium chloride and dilute sulfuric acid), followed by hydrolysis with dilute sulfuric acid and fermentation by Saccharomyces cerevisiae. The lignocellulosic composition of the sample was 47.98% cellulose, 28.15% hemicellulose and 22.3% lignin. Pretreatment with 1-butyl-3-methyl-imidazolium chloride (ionic liquid) showed an increase in cellulose content of around 4.25% and hemicellulose content of around 7.7%, with simultaneous delignification of 12.25%. In contrast, with dilute sulfuric acid, the lignin and cellulose content of the sample fell to 3.88% and 1.88% respectively. Hemicellulose content, on the other hand, increased by only 3.58%. After dilute acid hydrolysis (5% H2SO4), the values for total reducing sugar, glucose and xylose were 66.06±1.34 mg.g-1; 36.25 ± 1.2 mg.g-1 and 29.71 ± 0.6 mg.g-1 respectively. The percentage conversion of sugars was 55.16 ± 0.5% for cellulose to glucose and 53.76 ± 0.75% for hemicellulose to xylose. The hydrolyzed product of the complex polysaccharide was then converted to ethanol using commercial yeast. Results showed an ethanol yield of around 10.3%, and Fourier Transform Infrared (FTIR) spectroscopy results confirmed bioethanol production. A. bella oilseeds cakes are therefore a potential source for ethanol production.

A novel compatibilizer obtained from olive pomace oil maleate (OPOMA) and evaluation in PLA composite production

Alternative of using organic and biomass residues as additives or reinforcements in the production of composite materials has attracted great attention since the 2000s. However, when lignocellulosic biomass is used as natural fiber in composite production, it may have some disadvantages such as low interfacial bonding with the matrix phase. The most common methods used to strengthen the bonding between the matrix phase and the additive material is to use maleic anhydride (MA) as a compatibilizer and some chemicals such as dicumyl peroxide (DCP) as reaction initiators to increase the compatibilizing effect of MA. Therefore, in this study, olive pomace oil maleate (OPOMA) was prepared to be used in the production of PLA (polylactic acid) composites. Olive pomace obtained with ionic liquid pretreatment (OP-IL) in the previous studies of the authors and OPOMA were used in composite production with a biodegradable polymer of PLA. The composite was obtained by mixing 95PLA+5OP-IL by weight in twin-screw extruder at 190ºC for 10 minutes. Under the same conditions, the effect of OPOMA was evaluated by adding 0.5%, 1% and 2% ratio to PLA + OP-IL. In FTIR spectrum of OPOMA, a new symmetrical and asymmetric C=O bands were formed differently from olive oil. While the tensile strength of the PLA+OP mixture was approximately 10 MPa; the tensile strength value of PLA+OP-IL and PLA+OP-IL+OPOMA was around 60 MPa. The elasticity modulus showed less change compared to other mechanical properties. To conclude, it can be emphasized that oil maleates of lignocellulosic biomasses can be promising compatibilizer for biodegradable composite matrices.

Ionic liquid-assisted pretreatment of lignocellulosic biomass using purified Streptomyces MS2A cellulase for bioethanol production

In recent years, the process of producing bioethanol from lignocellulosic biomass through biorefining has become increasingly important. However, to obtain a high yield of ethanol, the complex structures in the feedstock must be broken down into simple sugars. A cost-effective and innovative method for achieving this is ionic liquid pre-treatment, which is widely used to efficiently hydrolyze the lignocellulosic material. The study aims to produce a significant profusion of bioethanol via catalytic hydrolysis of ionic liquid-treated lignocellulose biomass. The current study reports the purification of Streptomyces sp. MS2A cellulase via ultrafiltration and gel permeation chromatography. The kinetic parameters and the biochemical nature of the purified cellulase were analyzed for the effective breakdown of the EMIM[OAC] treated lignocellulose chain. The two-step cellulase purification resulted in 6.28 and 12.44 purification folds. The purified cellulase shows a Km value of 0.82 ± 0.21 mM, and a Vmax value of 85.59 ± 8.87 μmol min−1 mg−1 with the catalytic efficiency of 1.027 S−1. The thermodynamic parameters like ΔH, ΔS, and ΔG of the system were studied along with the thermal deactivation kinetics of cellulase. The optimal temperature and pH of the purified cellulase enzyme for hydrolysis was found to be 40 °C and 7. The rice husk and wheat husk used in this study were pretreated with the EMIM [OAC] ionic liquid and the change in the structure of lignocellulosic biomass was observed via HRSEM. The ionic liquid treated biomass showed the highest catalytic hydrolysis yield of 106.66 ± 0.19 mol/ml on the third day. The obtained glucose was fermented with Saccharomyces cerevisiae to yield 23.43 g of ethanol/l of glucose from the rice husk (RH) and 24.28 g of ethanol/l of glucose from the wheat husk (WH).

Efficacy and Functional Mechanisms of a Two-Stage Pretreatment Approach Based on Alkali and Ionic Liquid for Bioconversion of Waste Medium-Density Fiberboard.

A novel pretreatment strategy utilizing a combination of NaOH and 1-Butyl-3-methylimidazolium chloride ([Bmim]Cl) was proposed to enhance the enzymatic hydrolysis of abandoned Medium-density fiberboard (MDF). The synergistic effect of NaOH and [Bmim]Cl pretreatment significantly improved the glucose yield, reaching 445.8 mg/g within 72 h, which was 5.04 times higher than that of the untreated samples. The working mechanism was elucidated according to chemical composition, as well as FTIR, 13C NMR, XRD, and SEM analyses. The combined effects of NaOH and [Bmim]Cl led to lignin degradation, hemicellulose removal, the destruction and erosion of crystalline regions, pores, and an irregular microscopic morphology. In addition, by comparing the enzymatic hydrolysis sugar yield and elemental nitrogen content of untreated MDF samples, eucalyptus, and hot mill fibers (HMF), it was demonstrated that the presence of adhesives and additives in waste MDF significantly influences its hydrolysis process. The sugar yield of untreated MDF samples (88.5 mg/g) was compared with those subjected to hydrothermal pretreatment (183.2 mg/g), Ionic liquid (IL) pretreatment (406.1 mg/g), and microwave-assisted ionic liquid pretreatment (MWI) (281.3 mg/g). A long water bath pretreatment can reduce the effect of adhesives and additives on the enzymatic hydrolysis of waste MDF. The sugar yield produced by the combined pretreatment proposed in this study and the removal ability of adhesives and additives highlight the great potential of our pretreatment technology in the recycling of waste fiberboard.

An Ionic Liquid-Based Biorefinery Approach for Duckweed Utilization.

This study establishes a foundation for the ionic liquid (IL) pretreatment of duckweed biomass. An optimized IL-based process was designed to exploit the unique properties of duckweed including efficient metal removal, potential starch accumulation, and protein accumulation. Two ILs, namely, dimethylethanolammonium formate ([DMEtA][HCOO]) and N,N-dimethylbutylammonium hydrogen sulfate ([DMBA][HSO4]), were investigated for the pretreatment of two duckweed species (Spirodela polyrhiza and Lemna minor). The evaluation focused on starch recovery, sugar release, protein recovery, and metal extraction capabilities. [DMEtA][HCOO] demonstrated near-quantitative starch recoveries at 120 °C, while [DMBA][HSO4] showed similar performance at 90 °C within a reaction time of 2 h. Saccharification yields for most pulps exceeded 90% after 8 h of hydrolysis, outperforming "traditional" lignocellulosic biomasses such as miscanthus or sugarcane bagasse. Approximately 50 and 80 wt % of the protein were solubilized in [DMEtA][HCOO] and [DMBA][HSO4], respectively, while the remaining protein distributed between the pulp and lignin. However, the solubilized protein in the IL could not be recovered due to its low molecular weight. Regarding metal extraction, [DMEtA][HCOO] demonstrated higher efficiency, achieving 81% removal of Ni from Lemna minor's pulps, whereas [DMBA][HSO4] extracted only 28% of Ni with slightly higher pulp concentrations. These findings indicate the need for further optimization in concurrent metal extraction using ILs.

Ionic Liquid Pretreatment Enhances Skin Penetration of 5-Aminolevulinic Acid: A Promising Scheme for Photodynamic Therapy for Acne Vulgaris.

Acne vulgaris is one of the most prevalent skin disorders; it affects up to 85% of adolescents and often persists into adulthood. Topical 5-aminolevulinic acid (ALA)-based photodynamic therapy (PDT) provides an alternative treatment for acne; however, its efficacy is greatly undermined by the limited skin permeability of ALA. Herein, biocompatible ionic liquids (ILs) based on aliphatic acid/choline were employed to enhance the dermal delivery of ALA, thereby improving the efficacy of PDT. In addition to the one-step delivery of ALA by utilizing ILs as carriers, a two-step strategy of pretreating the skin with blank ILs, followed by the administration of free ALA, was employed to test the IL-facilitated dermal delivery of ALA in vitro. The cumulative permeation of ALA through the excised rat skin after IL pretreatment was significantly greater than that in the untreated group, the 20% dimethyl sulfoxide (DMSO) penetration enhancer group, and the one-step group. The penetration efficiency was influenced by formulation and treatment factors, including the type of IL, pretreatment duration, water content in the ILs, and concentration of ALA. In rats, IL pretreatment facilitated faster, greater, and deeper ALA-induced protoporphyrin IX (PpIX) accumulation. Moreover, the IL pretreatment regimen significantly improved the efficacy of ALA-based PDT against acne vulgaris in a rat ear model. The model IL choline citrate ([Ch]3[Cit]1) had a moderate effect on the skin barrier. Trans-epidermal water loss could be recovered 1 h after IL treatment, but no irritation to the rat skin was detected after 7 days of consecutive treatment. It was concluded that biocompatible IL pretreatment enhances the penetration of ALA and thus facilitates the transformation of PpIX and improves the efficacy of PDT against acne vulgaris.

Multi enzyme production from mixed untreated agricultural residues applied in enzymatic saccharification of lignocellulosic biomass for biofuel

Lignocellulose recalcitrance essentially dictates high cost and low efficiency of its enzymatic saccharification. The complex lignocellulosic structure is a major obstacle to enzymatic saccharification and green ionic liquid pretreatment methods face difficulty of water washing prior enzymatic hydrolysis. Ionic liquid tolerant lignocellulolytic enzymes overcome the inhibition of enzymes during enzymatic saccharification and eliminated water washing step after pretreatment of lignocellulosic biomass. The cell wall composition cellulose, hemicellulose, and lignin, three main wall polymers of various agricultural residues and food waste lignocellulose substrates also affected the enzyme activities secreted by the B. subtilis strain. This study explores the potential of the halophilic, alkalophilic, and ionic liquid (IL)-tolerant strain Bacillus subtilis BC-001 for the simultaneous production of hydrolytic enzymes essential for lignocellulosic bio-refinery processes. BC-001 produced cellulase, amylase, xylanase, pectinase and protease are 70.41, 87.14, 65.50, 122.55 and 66.48 U/mL, respectively under optimized fermentation conditions. Cellulase produced by BC-001 retained more than 80% activity after 72 hours in 20% w/w of different ILs tested and enzymes retained more than 68% activities after 12 h in 50% w/w ILs. Employing such IL-stable cellulase, enzymatic saccharification is conducted without water washing on rice straw (RS) that has been pretreated with various ILs, including 1-ethyl-3-methylimidazolium chloride, 1-butyl-3-methylimidazolium chloride, and choline chloride. This research is novel as the study marks the first instance of multi-hydrolytic enzyme production from a novel alkalophilic, halophilic, thermophilic, and IL-tolerant bacterial strain using a mixture of untreated agricultural residues.

Theoretical Calculation of Different Side-Chain Lengths [Cnmim]FeCl4 and Factors Influencing Coal Pyrolysis Swelling Modification.

With the increasing requirements for clean and effective utilization, coal swelling pretreatment provides a good theoretical basis for coal molecular structure, application in coal pyrolysis, and liquefaction. Ionic liquids containing magnetic anionic groups were designed, synthesized, and used as solvents to study the effect on swelling pyrolysis performance. Studies have shown magnetism enhancement with the growth of alkyl chains. The growth of the MIL alkyl side chain made the modification effect of coal more obvious, and the swelling degree showed a trend of first increasing and then decreasing with the increase of temperature and time, and at the temperature of 35 °C, the swelling degree is the largest when the modification time is 8 h. Pyrolysis experiments show that magnetic ionic liquid (MIL) pretreatment can significantly reduce the temperature at the maximum weight loss of coal and increase the tar content of pyrolysis, indicating that MIL plays a catalytic cracking role in coal pyrolysis.

Total component transformation of corn stalk to ethyl levulinate assisted by ionic liquid pretreatment

Total component transformation of corn stalk to ethyl levulinate assisted by ionic liquid pretreatment

Innovative ionic liquid pretreatment followed by wet disk milling treatment provides enhanced properties of sugar palm nano-fibrillated cellulose

In order to accommodate the increased demand for innovative materials, intensive research has focused on natural resources. In pursuit of advanced substances that exhibit functionality, sustainability, recyclability, and cost-effectiveness, the present work attempted an alternative study on cellulose nanofibers derived from sugar palm fiber. Leveraging an innovative approach involving ionic liquid (IL) pre-treatment, bleaching, and wet disc mill technique, nano-fibrillated cellulose (NFC) was successfully obtained from the sugar palm fiber source. Remarkably, 96.89% of nanofibers were extracted from the sugar palm fiber, demonstrating the process's efficacy and scalability. Further investigation revealed that the sugar palm nano-fibrillated cellulose (SPNFC) exhibited a surface area of 3.46 m2/g, indicating a significant interface for enhanced functionality. Additionally, the analysis unveiled an average pore size of 4.47 nm, affirming its suitability for various applications that necessitate precise filtration. Moreover, the surface charge densities of SPNFC were found to be −32.1 mV, offering opportunities for surface modification and enhanced interactions with various materials. The SPNFC exhibit remarkable thermal stability, enduring temperatures of up to 360.5 °C. Additionally, the isolation process is evident in a significant rise in the crystallinity index, escalating from 50.97% in raw fibers to 61.62% in SPNFC. These findings shed light on the vast potential and distinct features of SPNFC, opening the path for its application in a wide array of industries, including but not limited to advanced materials, biomedicine, and environmental engineering.

Enzymatic hydrolysates of Agave tequilana bagasse pretreated with protic ionic liquids: Saccharification efficiency and hydrogen production

This work demonstrated for the first time that hydrogen (H2) can be generated from Agave tequilana bagasse (ATB) after ionic liquid (IL) pretreatment up to 111.1 L H2/kg hydrolyzed biomass in only 20 h. It is shown that the low-cost protic IL [EOA][OAc] (ethanolamine acetate) can effectively pretreat ATB at two different scales (bench and lab) using 2 and 250 g (dry basis) at 20% solids loading and 160 °C for 90 min resulting in significant structural changes followed by FTIR spectroscopy. The lignin content of the pretreated ATB was reduced by 28.6% after lab-scale pretreatment which ultimately improved the sugar yield with the different saccharification strategies (batch vs. fed-batch). Up to 0.643 g TS (total sugars)/g ATB were obtained in a fed-batch strategy with fixed enzymatic loading, representing an enhancing 2.8-fold when compared to the untreated biomass. Models of enzymatic saccharifications were included for both, untreated and pretreated ATB, in terms of TS concentration (g/L) and fiber length (mm) to confirm differences in accessibility and availability of both substrates. The results successfully revealed that 1.1 kg or 14 m3 of H2 can be produced from 100 kg of dry ATB after pretreatment with [EOA][OAc] indicating the feasibility of improved sugar and H2 yields where either a low-cost pretreatment agent or an adequate saccharification strategy contributes to the biorefinery scheme.

Robust Oxidase-Mimetic Supramolecular Nanocatalyst for Lignin Biodegradation.

Enzymatic catalysis presents an eco-friendly, energy-efficient method for lignin degradation. However, challenges arise due to the inherent incompatibility between enzymes and native lignin. In this work, we introduce a supramolecular catalyst composed of fluorenyl-modified amino acids and Cu2+, designed based on the aromatic stacking of the fluorenyl group, which can operate in ionic liquid environments suitable for the dissolution of native lignin. Amino acids and halide anions of ionic liquids shape the copper site's coordination sphere, showcasing remarkable catechol oxidase-mimetic activity. The catalyst exhibits thermophilic property, and maintains oxidative activity up to 75 °C, which allows the catalyzed degradation of the as-dissolved native lignin with high efficiency even without assistance of the electron mediator. In contrast, at this condition, the native copper-dependent oxidase completely lost its activity. This catalyst with superior stability and activity offer promise for sustainable lignin valorization through biocatalytic routes compatible with ionic liquid pretreatment, addressing limitations in native enzymes for industrially relevant conditions.

Potential of ionic liquids as emerging green solvent for the pretreatment of lignocellulosic biomass.

Lignocellulosic biomass is available in abundance as a renewable resource, but the major portion of it is often discarded as waste without utilizing its immense potential as an alternative renewable energy resource. To overcome recalcitrance of lignocellulosic biomass, various pretreatment methods are applied to it, so that the complex and rigid polymeric structure can be broken down into fractions susceptible for enzymatic hydrolysis. Effective and efficient biomass processing is the goal of pretreatment methods, but none of the explored pretreatment methods are versatile enough to fulfil the requirement of biomass processing with greater flexibility in terms of operational cost and desired output efficiency. Deployment of green solvents such as ionic liquids for the pretreatment of lignocellulosic biomass has been a topic of discussion amongst the scientific community in recent times. The presented work provides a detailed overview on the deployment of ionic liquid for the pretreatment of lignocellulosic biomass coupled with a brief discussion on other pretreatments methods. The recyclability and reusability along with other unique properties makes an ionic liquid pretreatment different from the other traditional pretreatment methods. Also, this study explores diverse critical parameters that governs the dissolution process of biomass. Hazardous properties of ionic liquids have also been explored. Future perspective and recommendations have been given for an efficient, effective, and eco-friendly deployment of ionic liquid in biomass pretreatment process.

Effect of surface modification of microcrystalline cellulose with ionic liquids on natural latex composites

AbstractAs an environmentally friendly biomacromolecular material, microcrystalline cellulose (MCC) enhances the performance of natural rubber latex (NRL) composites. However, MCC has strong polarity, which weakens the interfacial interaction between MCC and the non‐polar NRL matrix and reduces the reinforcing performance due to the many hydroxyl groups on its surface. In this paper, the ionic liquid (IL) modified MCC/IL material was prepared, and AIR‐FTIR, x‐ray diffraction, and XPS photoelectron spectroscopy were performed to detect it from the perspective of environmental protection. And natural latex/microcrystalline cellulose/ionic liquid (NRL/MCC/IL) composites with excellent properties were prepared by latex blending. The activation energy, vulcanization characteristics, basic mechanical properties, dynamic mechanical properties, and filler‐rubber interfacial interactions of NRL/MCC/IL composites were investigated. The results showed that the vulcanization rate constant of NRL/MCC/IL composites increase, the activation energy decreases and the mechanical properties were significantly improved. At the same time, the matrix interface interaction of composites was quantitatively calculated using Ayala parameters. The results showed that the interfacial interaction force of the composite was stronger after an appropriate amount of IL pretreatment. The whole process is not only conformed to the concept of green development, but also broadens the application of MCC in rubber materials.

Biomass pretreatment with distillable ionic liquids for an effective recycling and recovery approach

Ionic liquid (IL) pretreatment methods show incredible promise for the efficient conversion of lignocellulosic feedstocks to fuels and chemicals. Given their low vapor pressures, distillation-based methods of extracting ionic liquids out of biomass post-pretreatment have historically been ignored in favor of alternative methods. We demonstrate a process to distill four acetate-based ionic liquids ([EthA][OAc], [PropA][OAc], [MAEthA][OAc], and [DMAEthA][OAc]) at low pressure and high purity that overcome some disadvantages of “water washing” and “one pot” recovery methods. Out of four tested ILs, ethanolamine acetate ([EthA][OAc]) is shown to have the most agreeable conversion metrics for commercial bioconversion processes achieving 73.6 % and 51.4 % of theoretical glucose and xylose yields respectively and >85 % recovery rates. Our process metrics are factored into a techno-economic analysis where [EthA][OAc] distillation is compared to other recovery methods as well as ethanolamine pretreatment at both milliliter and liter scales. Although our TEA shows [EthA][OAc] distillation underperforming against other processes, we show a step-by-step avenue to reduce sugar production cost below the wholesale dextrose price at scale.