Iodide Solution Research Articles

A facile approach for fabricating efficient and stable perovskite solar cells.

Perovskite solar cells (PSCs) with high power conversion efficiencies (PCEs) can be produced using a variety of methods, such as different fabrication methods, device layout modification, and component and interface engineering. The efficiency of a perovskite solar cell is largely dependent on the overall quality of the perovskite thin-film in every scenario. The utilization of spin-coating followed by the antisolvent pouring (ASP) method is prevalent in nearly all fabrication techniques to achieve superior perovskite thin-films. Nevertheless, there are a few guidelines that must be followed precisely when using the ASP approach, including the antisolvent amount, duration, and area for dropping. The aforementioned challenging and necessary strategies frequently result in perovskite thin-films with pinholes, tiny grains, and broad grain boundaries, which impair the performance of PSCs. Therefore, the implementation of a straightforward approach that does not require the use of such complex ASP steps is crucial. Here, we employ a simple process that involves the hot-dipping of lead iodide (PbI2) thin-films in a hot solution of methylammonium iodide (MAI) and formamidinium iodide (FAI) in isopropanol (IPA) to produce high-quality perovskite thin-films. As the time required for the desired perovskite to crystallize is critical, we carefully examined various hot-dipping process times, such as 10 seconds, 20 seconds, 30 seconds, and 40 seconds. These time intervals yielded thin-films, which were named PSK-10, PSK-20, PSK-30, and PSK-40, respectively. Morphological and optoelectronic characterization demonstrated the high quality of the perovskite thin-films obtained through dipping PbI2 for 30 seconds. Consequently, the PSK-30-based PSCs produced higher PCEs of up to 21.52% compared to those of the ASP-based devices (20.79%). Furthermore, the unsealed PSCs prepared with PSK-30 and ASP were assessed for 252 hours at 25 °C and 40-45% relative humidity in order to determine their operational stability. The ASP-based device showed poor stability, retaining only 10% of its original PCE, whereas the PSK-30-based device retained 70% of its initial PCE. These results offer a new and viable approach for producing highly efficient and stable PSCs.

Effects of Silver Diamine Fluoride and Potassium Iodide Solutions on the Anti-Caries Properties, Surface Hardness, and Bond Strength of Resin Modified Glass Ionomer in Dentin

This study evaluated the effects of silver diamine fluoride (SDF) and potassium iodide (PI) on carious dentin. The antibacterial efficacy, surface hardness, and bond strength of resin-modified glass ionomer cement (RMGI) were assessed. Dentin specimens were prepared and subjected to artificial caries formation. The antibacterial effect of SDF/PI was compared to sodium fluoride varnish using Streptococcus mutans colony counts. Surface microhardness was measured using the Vickers hardness test. Shear bond strength of RMGI to treated surfaces was evaluated after thermocycling. Results showed that SDF/PI had superior antibacterial effects compared to NaF varnish. Surface hardness significantly increased one week after SDF/PI application. While SDF/PI treatment did not immediately affect RMGI bond strength to carious dentin, delayed bonding after one week significantly improved bond strength. These findings suggest that SDF/PI is effective in arresting caries and enhancing remineralization of carious dentin. The study also indicates that delaying restoration placement for one week after SDF/PI application may be beneficial for improving bond strength. This research provides valuable insights into the clinical application of SDF/PI for caries management and subsequent restorative procedures.

Pre-treatment of Remelting Recovery: Ultrasonic Cleaning Mechanism of Non-metallic Layers from Superalloy Scrap Under Based on Hydrochloric Acid and Potassium Iodide Solution System

Pre-treatment of Remelting Recovery: Ultrasonic Cleaning Mechanism of Non-metallic Layers from Superalloy Scrap Under Based on Hydrochloric Acid and Potassium Iodide Solution System

Structural Study of Aqueous Electrolyte Solution by MeV Liquid Electron Scattering.

The impact of ions on water has long been a subject of great interest, as it is closely tied to the hydration structure, dynamics, and properties of electrolyte solutions. Over centuries of investigation, the influence of ions on water's structure remains highly debated. Prevailing techniques, such as neutron and X-ray scattering, primarily focus on the microscopic structure of salt solutions at very high concentrations, mostly above 1 mol/L. In this study, we measured the structure of aqueous potassium iodide (KI) and potassium chloride (KCl) solutions using MeV liquid electron scattering (MeV-LES) across a concentration range of 0.10 to 0.75 mol/L. The obtained results provide detailed insights into the variations in ion-oxygen and oxygen-oxygen correlations as a function of concentration. The observed structural differences between KI and KCl solutions are in line with the structure maker/breaker theory, which suggests that iodide ions exert a more pronounced effect than chloride ions on disrupting the water shell. This work demonstrates the potency of MeV-LES for investigating the atomic structure in liquids, augmenting the modern analytical toolbox.

PEAI Surface Treatment for Low Ion Migration and High-Performance FAPbBr3 Single-Crystal X-ray Detectors.

Organometal halide perovskite single crystals (SCs) are the most promising candidates for the next generation of radiation detection materials. However, surface defects severely affect their detection performance and limit further applications. Here, we identified the surface defect types of FAPbBr3 SCs and employed phenethylammonium iodide (PEAI) solution to treat the crystal surface and to investigate their effects on ion migration, photoelectric performance, and X-ray detection performance. Our experimental results demonstrated that the surface defects, such as the metallic Pb and Br vacancies, can be effectively passivated by both the PEAI and the two-dimensional (2D) PEA2PbI4 layers. The PEAI layer can elongate the carrier lifetime, lower the trap density, and suppress ion migration in FAPbBr3 SCs. The 2D PEA2PbI4 layer can form a dense and full surface coverage, suppress ion migration, and lower the dark current of the SCs. The X-ray sensitivity of the PEAI-passivated FAPbBr3 SC detectors is 227.93 μCGyair-1 cm-2, which is an order of magnitude higher than that of the pristine FAPbBr3 SC detectors. This work demonstrates that surface treatment plays a critical role in the crystal quality and the X-ray detection performance of SCs.

Multiphase distribution in partly saturated hierarchical nonwoven fibre networks under applied load using X-ray computed tomography

In many industrial applications, nonwoven fibre networks are facilitated to operate under partly saturated conditions, allowing for filtration, liquid absorption and liquid transport. Resolving the governing liquid distribution in loaded polyamide-6 (PA6) fibre networks using X-ray computed micro-tomography is a challenge due to the similar X-ray attenuation coefficients of water and PA6 and limitations in using background subtraction techniques if the network is deformed, which will be the case if subjected to compression. In this work, we developed a method using a potassium iodide solution in water to enhance the liquid’s attenuation coefficient without modifying the water’s rheological properties. Therefore, we studied the evolving liquid distribution in loaded and partly saturated PA6 fibre networks on the microscale. Increasing the external load applied to the network, we observed an exponential decrease in air content while the liquid content was constant, increasing the overall saturation with increasing network strain. Furthermore, the microstructural properties created by the punch-needle process in the manufacturing of the network significantly influenced the out-of-plane liquid distribution. The method has been proven helpful in understanding the results of adaptions in both the fibre network design and manufacturing process, allowing for investigating the resulting liquid distribution on a microscale.

Treatment Challenges of Methimazole-Induced Agranulocytosis in Younger Patients

Introduction: Methimazole is considered the first-line antithyroid drug for Graves’ disease (GD) in children and adolescents. However, it can lead to severe adverse effects, such as agranulocytosis, which can result from direct drug toxicity or immune-mediated responses. This report aims to describe the clinical management of an adolescent with GD who developed agranulocytosis following methimazole administration. Case Presentation: A 13-year-old female, diagnosed with GD, developed neutropenia six months after starting methimazole. She was admitted with high-grade fever, sore throat, palpitations, fatigue, myalgia, and diarrhea. The treatment regimen included filgrastim, antibiotics, β-blockers, a solution of potassium iodide (SSKI), cholestyramine, and lithium. Within seven days, her absolute neutrophil count gradually improved, her fever subsided, her hyperthyroidism was controlled, and she was discharged. Discussion: Antithyroid drug-induced neutropenia represents a serious complication. In these patients, effective infection management, control of hyperthyroidism, and supportive measures to promptly increase the neutrophil count can reduce the associated morbidity and mortality. Conclusions: Close monitoring and awareness of risk factors, such as age, female sex, and higher doses of methimazole, may decrease the risk of agranulocytosis and its fatal outcomes. Alternative treatments to control hyperthyroidism during methimazole-induced agranulocytosis include β-blockade, potassium iodide solution (SSKI), cholestyramine, steroids, and lithium.

Surface Engineering Enables Efficient AgBiS2 Quantum Dot Solar Cells.

Surface ligand chemistry is vital to control the synthesis, diminish surface defects, and improve the electronic coupling of quantum dots (QDs) toward emerging applications in optoelectronic devices. Here, we successfully develop highly homogeneous and dispersed AgBiS2 QDs, focus on the control of interdot spacing, and substitute the long-chain ligands with ammonium iodide in solution. This results in improved electronic coupling of AgBiS2 QDs with excellent surface passivation, which greatly facilitates carrier transport within the QD films. Based on the stable AgBiS2 QD dispersion with the optimal ligand state, a homogeneous and densely packed QD film is prepared by a facile one-step coating process, delivering a champion power conversion efficiency of approximately 8% in the QD solar cells with outstanding shelf life stability. The proposed surface engineering strategy holds the potential to become a universal preprocessing step in the realm of high-performance QD optoelectronic devices.

Spontaneous Production of I2 at the Surface of Aqueous Iodide Solutions.

Several groups have recently reported spontaneous production of atmospherically reactive species, including molecular iodine (I2) at the air-water interface of droplets. In this study, glancing angle laser-induced fluorescence spectroscopy was used to track the luminol fluorescence at the surface of sodium iodide (NaI) and sodium chloride (NaCl) solutions. Although luminol fluorescence is hardly quenched by halide anions, even up to fairly high concentrations, it is effectively quenched by I2. We observe luminol fluorescence quenching at the surface of NaI solutions but not at the surface of NaCl solutions, pointing to the formation of I2 at the surface of NaI solutions. This provides further support for the proposal that the strong electric field or the reduction solvation present at the air-water interface can initiate spontaneous iodide activation and other chemistry there. The spontaneous production of I2 at the surface of aqueous iodide solutions presents a previously unconsidered source of iodine in the atmosphere.

Based on SIRT1/NF-κB/NLRP3 Signal Pathway to Explore the Effect of Yiqi Huatan Huoxue Recipe on Inflammatory Injury in AIT Mice by Pyroptosis.

Autoimmune thyroiditis (AIT) is the most common autoimmune thyroid disease. In recent decades, its incidence and prevalence have sharply increased. Yiqi Huatan Huoxue recipe is a traditional Chinese medicine formula we use to treat AIT. Its clinical efficacy is clear, but the specific mechanism remains unclear. This study aims to explore whether pyroptosis mediated by the SIRT1/NF-κB/NLRP3 signaling pathway is one of the therapeutic mechanisms of Yiqi Huatan Huoxue recipe. Forty 8-week-old female NOD.H-2h4 mice were randomly divided into four groups: the normal group (NG), model group (MG), Yiqi Huatan Huoxue recipe group (YG), and western medicine group (selenium yeast tablet, SeG). The normal group was gavaged with distilled water, while the remaining groups were gavaged with 0.05% sodium iodide (NaI) solution for 8 weeks. After the AIT animal model formed naturally, the mice were euthanized by gavage after 8 weeks. Hematoxylin-eosin staining was used to observe thyroid tissue changes, and enzymelinked immunosorbent assay (ELISA) was used to detect serum anti-thyroglobulin antibodies (TGAb) and mouse anti-thyroid peroxidase antibodies (TPOAb). Real-time quantitative PCR (qRT-PCR), Western blot, and immunohistochemistry were used to detect the expression of sirtuin 1 (SIRT1), nuclear factor κB p65 (NF-κB p65), nod-like receptor protein 3 (NLRP3), apoptosis-associated speck-like protein containing a caspase recruitment domain (ASC), caspase- 1, gasdermin D (GSDMD), and interleukin (IL)-1β in thyroid tissue. Compared with the NG group, the thyroid structure of rats in the MG group was severely damaged, with significant lymphocyte infiltration, significantly increased serum TGAb and TPOAb levels, and significantly increased expression levels of SRIT1, NF-κB p65, NLRP3, ASC, Caspase-1, GSDMD, IL-1β mRNA, and protein. Compared with the MG group, the thyroid structure damage and lymphocyte infiltration in rats of each treatment group were improved, and the serum TGAb, TPOAb, SRIT1, NF-κB p65, NLRP3, ASC, Caspase-1, GSDMD, IL-1β mRNA, and protein expression levels were significantly reduced. Yiqi Huatan Huoxue recipe can alleviate thyroid structural damage in AIT mice, and its mechanism may be related to the upregulation of SIRT1, NF-κB deacetylation, and inhibition of NLRP3-mediated pyroptosis.

Cryogenic Atom Probe Tomograph to Resolve Confined Electrochemical Interfaces

Atom Probe Tomography (APT) is an analysis technique capable of providing a 3-dimensional, element-sensitive map of needle-shaped samples (where the tip radius is about 50 nm) with sub-nanometre resolution [1]. APT analysis is carried out at temperatures in the range of 25-75 K to limit the thermal motion of surface atoms which improves the spatial and mass resolution. As a result, this enables the analysis of frozen liquids, and by extension solid-liquid interfaces, by so-called “cryo-APT”. While this was historically challenging, recent advancements in UHV-cryogenic transfer and sample preparation methods now make it possible for the atomic scale analysis of interfacial species in electrochemical systems [2-4].In this study, we will attempt to explore the effect of nanoscale geometrical confinement on the distribution of interfacial ions for the first time and to resolve the electric double layer, using cryo-APT. We will describe the workflow for cryo-APT sample preparation to study confined solid-liquid interfaces, using nanoporous gold as a template material with a frozen sodium iodide solution inside its pores. APT reconstructions will allow 3-dimensional mapping of aqueous interfacial species, helping to develop our understanding of the structure of the electric double layer under nanoscale geometrical confinement. The attached Figure shows an SEM image of the later stages of cryo-FIB milling of an APT tip of frozen deionised water and 50 mM sodium iodide and a segment of the related APT atom map reconstruction.

Iodide- and electrochemical assisted removal of mercury by Cirsium arvense from gold tailings in the Amansie West District, Ghana

Mercury (Hg) pollution in Ghana through mining has become a serious environmental challenge. This study investigates the potential of Cirsium arvense to photostabilize Hg using electrokinetic current with or without an iodide solution in gold mine tailings heavily contaminated through mining activities in southern Ghana. An initial Hg concentration of 9.60 mg/kg using cold vapor atomic absorption spectrometry (CVAAS) was determined. The biological absorption coefficient, bioconcentration factor, and translocation factor of Hg have been presented. Cirsium arvense therefore had a higher bioconcentration factor (BCF) of 2.6–5.15 mg/kg, and a transfer factor (TF) of 0.24–0.36 indicating a higher efficiency for phytostabilization. Both the rate and time of extractions of Hg from the tailings by Cirsium arvense are efficiently improved in the combined electric current and iodide treatment. Plant and electric current combined treatment and plant and iodide combined treatment had only 60 and 50% phytostabilization rates, respectively. The combined plant, iodide, and electric current treatment has proven to be superior with about >90% Hg removal rate. Therefore, the combined plant, iodide, and electric current treatment resulted in a higher Hg removal efficiency by Cirsium arvense in a shorter period due to higher solubilization rate and electromigration effects on Hg species.

In Vitro Inhibitory Effect of Silver Diamine Fluoride Combined with Potassium Iodide against Mixed-Species Biofilm Formation on Human Root Dentin.

Applying a saturated potassium iodide (KI) solution immediately after silver diamine fluoride (SDF) application may affect the inhibitory effects of SDF on biofilm formation. This study compared the efficacy of 38% SDF with and without KI on preventing mixed-species biofilm formation on human root dentin surfaces and assessed ion incorporation into root dentin. The biofilms, composed of Streptococcus mutans, Lactobacillus rhamnosus, and Actinomyces naeslundii, were grown on specimen surfaces treated with either SDF or SDF + KI. After 24 h, the biofilms were evaluated using scanning electron microscopy, live/dead staining, adenosine triphosphate (ATP) assays, colony-forming unit (CFU) counts, and quantitative polymerase chain reaction. A Mann-Whitney U test was used to compare the results between the groups. Ion incorporation was assessed using an electron probe microanalyzer. The relative ATP content in the SDF + KI group was significantly higher than that in the SDF group (p < 0.05). However, biofilm morphology and the logarithmic reduction in CFUs and bacterial DNA were comparable across the groups. The SDF + KI treatment resulted in less silver and fluoride ion incorporation than that yielded by SDF alone. The inhibitory effects of SDF and SDF + KI on mixed-species biofilm formation were almost equivalent, although KI application affected the ion incorporation.

Rapid, low-cost determination of Hg2+, Cu2+, and Fe3+ using a cellulose paper-based sensor and UV–vis method with silver nanoparticles synthesized with S. mammosum

As water effluents are often highly contaminated with metals, having a quick and cost-effective method of analysis is crucial. This study used the supernatant derived from the green synthesis of silver nanoparticles (AgNPs) with Solanum mammosum to detect mercury, copper, and iron with a low-cost cellulose paper-based sensor and a rapid colorimetric method applying ultraviolet–visible spectroscopy (UV–Vis). AgNPs in two precursor concentrations using silver nitrate, 1 mM (17.4 ± 9 nm) and 50 mM (and 22 ± 8.1 nm), were utilized to assess the efficacy of the analysis and removal of Hg2+, Cu2+, and Fe3+ from contaminated water. Cellulose paper-based sensor showed limits of detection (LODs) for Hg2+ of 2.46 and 123 μM using AgNPs at concentrations of 1 and 50 mM, respectively. For Cu2+, the LODs were 55 and 2750 μM, and for Fe3+, the LODs were 49 and 2470 μM using the respective concentrations. To differentiate and detect the cations with the naked eye, a potassium iodide and potassium ferrocyanide (1:1) aqueous solution was used, producing a yellow, pink, and blue color for Hg2+, Cu2+, and Fe3+, respectively. Additionally, the titration curves of Hg2+, Fe3+, and Cu2+ were examined by UV–Vis using the supernatant liquid. The LODs for the UV–Vis method using AgNPs at a concentration of 1 mM were 1.50 μM for Hg2+, 10.7 μM for Cu2+, and 4.33 μM for Fe3+, while the LODs for AgNPs at 50 mM were 5.75, 27.6, and 15 μM for Hg2+, Cu2+, and Fe3+, respectively. Furthermore, these nanoparticles were utilized to assess the efficacy of the removal of Hg2+, Cu2+, and Fe3+ from contaminated water. Removal efficiency with the solid 50 mM AgNPs was analyzed via flame absorption spectrophotometry; values over 95% were obtained for the three ions. The results underscore the effectiveness of a green synthesis approach to generating AgNPs, enabling efficient and economical cation analysis and water decontamination.

Obtention of Suitable Pregnant Leach Solution (PLS) for Copper Solvent Extraction Plants from Copper Concentrate Using Hydrogen Peroxide and Iodine in a Sulfuric Acid–Chloride Medium

Copper leaching presents an environmentally friendly alternative to traditional sulfide ore processing methods. This study investigates an efficient leaching process for copper concentrate, utilizing a solution of sulfuric acid (H2SO4) and potassium iodide (KI) in a chloride medium (NaCl), enhanced by hydrogen peroxide (H2O2) at room temperature. A significant aspect of this research was optimizing the KI concentration to minimize iodide sublimation into iodine gas (I2). Through the experimental design, the optimal dosages of reagents were determined, leading to maximized copper extraction of approximately 27% in 45 min of testing at room temperature. The results showed that it is possible to obtain a suitable pregnant leach solution (PLS) (i.e., in the range of 3 to 8 g/L of Cu) for treatment in available copper solvent extraction (SX) plants with a cost of less than 4.5 USD/t Cu, according to the economic analysis carried out. The results of this study determine the most effective operational conditions for leaching and ensure a suitable PLS for SX plants in a cost-effective and environmentally friendly manner. This approach could significantly contribute to more sustainable practices in the mining and processing of copper ores.

Two-step preparation of methylammonium lead triiodide perovskite film via electrospray deposition of methylammonium iodide solution for solar cell applications

Solution-processable perovskite solar cells (PSCs) have the potential to revolutionize solar cell technology by enabling low power generation costs via low-cost device fabrication. However, most existing research regarding PSCs relies on the spin-coating method, which is not conducive to large-area film deposition. Therefore, the development of an alternative deposition method for perovskite films has become increasingly important for commercialization, for which electrospray deposition is a promising technique. This study investigates the two-step preparation of methylammonium lead triiodide (MAPbI3) perovskite films via the electrospray deposition of a methylammonium iodide (MAI) solution on a spin-coated PbI2 film. The gradual conversion of PbI2 to MAPbI3 with increasing MAI deposition time was revealed, accompanied by an increase in the size of the perovskite crystals. In addition, PSCs were successfully fabricated by electrospraying MAI, achieving a considerable power conversion efficiency of 7.86 % at the optimal MAI deposition time.

Excess Iodine Consumption Induces Oxidative Stress and Pancreatic Damage Independently of Chemical Form in Male Wistar Rats: Participation of PPAR-γ and C/EBP-β.

Human beings consume different chemical forms of iodine in their diet. These are transported by different mechanisms in the cell. The forms of iodine can be part of thyroid hormones, bind to lipids, be an antioxidant, or be an oxidant, depending on their chemical form. The excessive consumption of iodine has been associated with pancreatic damage and diabetes mellitus type 2, but the association between disease and the chemical form consumed in the diet is unknown. This research analyzes the effect of excessive iodine consumption as Lugol (molecular iodine/potassium iodide solution) and iodate on parameters of pancreatic function, thyroid and lipid profiles, antioxidant and oxidant status, the expression of IR/Akt/P-Akt/GLUT4, and transcription factors PPAR-γ and CEBP-β. Three groups of Wistar rats were treated with 300 μg/L of iodine in drinking water: (1) control, (2) KIO3, and (3) Lugol. Lugol and KIO3 consumption increased total iodine levels. Only KIO3 increased TSH levels. Both induced high serum glucose levels and increased oxidative stress and pancreatic alpha-amylase activity. Insulin levels and antioxidant status decreased significantly. PPAR-γ and C/EBP-β mRNA expression increased. The pancreatic damage, hypertriglyceridemia, and oxidative stress were independent of the chemical form of iodine consumed. These effects depended on PPAR-γ, C/EBP-β, GLUT-4, and IR.

Optical maneuvering of photofunctioning hybrid perovskite for future photonics potential application

Hybrid perovskites, known for their multidimensional opto-electronic properties and capability to generate multi-color emission bands, are highly sought after for light-emitting devices due to their liquid crystalline behavior in the solution phase. This behavior enables easier ion mobility, facilitating ion exchange processes. Exploiting the liquid crystalline properties of perovskites, we applied a halogen exchange reaction in the solution phase using tightly focused laser trapping techniques. Our study demonstrates the successful development of high-luminescent bulk single crystals of methylammonium lead halide alloy MAPb(Br/I)3, which exhibit multi-color emission capabilities, underscoring their potential for optoelectronic applications. We fabricated bulk single crystals of MAPbBr3, measuring 20 × 20 μm2, displaying bright green luminescence. Using a tightly focused trapping laser beam (1064 nm, 1 Watt) with a high numerical aperture (0.9, 60X objective lens), we irradiated a specific area of the green luminescent MAPbBr3 single crystal immersed in a 200 μM methylammonium iodide (MAI) solution for 30 min at room temperature. This treatment induced a red emission band at 605 nm at the irradiated location, while surrounding areas retained the original green luminescence. In a parallel experiment, increasing the iodide concentration to 300 μM caused the emission color of a similar-sized crystal to change uniformly from green to red. Photoluminescence spectroscopy and EDS confirmed the halide exchange from MAPbBr3 to MAPbBr2.3I0.7. This method, influenced by laser parameters such as power, wavelength, and aperture, provides new opportunities for multi-color emission patterning and offers significant insights for advancing optoelectronics.

High‐performance 110 kVp hard x‐ray detector based on all‐crystalline‐surface passivated perovskite single crystals

AbstractHalide perovskite single crystals (SCs) have attracted much attention for their application in high‐performance x‐ray detectors owing to their desirable properties, including low defect density, high mobility–lifetime product (μτ), and long carrier diffusion length. However, suppressing the inherent defects in perovskites and overcoming the ion migration primarily caused by these defects remains a challenge. This study proposes a facile process for dipping Cs0.05FA0.9MA0.05PbI3 SCs synthesized by a solution‐based inverse temperature crystallization method into a 2‐phenylethylammonium iodide (PEAI) solution to reduce the number of defects, inhibit ion migration, and increase x‐ray sensitivity. Compared to conventional spin coating, this simple dipping process forms a two‐dimensional PEA2PbI4 layer on all SC surfaces without further treatment, effectively passivating all surfaces of the inherently defective SCs and minimizing ion migration. As a result, the PEAI‐treated perovskite SC‐based x‐ray detector achieves a record x‐ray sensitivity of 1.3 × 105 μC Gyair−1 cm−2 with a bias voltage of 30 V at realistic clinical dose rates of 1–5 mGy s−1 (peak potential of 110 kVp), which is 6 times more sensitive than an untreated SC‐based detector and 3 orders of magnitude more sensitive than a commercial α‐Se‐based detector. Furthermore, the PEAI‐treated‐perovskite SC‐based x‐ray detector exhibits a low detection limit (73 nGy s−1), improved x‐ray response, and clear x‐ray images by a scanning method, highlighting the effectiveness of the PEAI dipping approach for fabricating next‐generation x‐ray detectors.image

Rapid spectrophotometric determination and extraction of platinum(IV) from pharmaceuticals assisted by 2-(2-(1-(thiophene-2-yl) ethylidene) hydrazinyl) benzoic acid (TEHBA).

It has been suggested that the chelating agent 2-(2-(1-thiophene-2-yl) ethylidene) hydrazinyl) benzoic acid (TEHBA) be utilized to extract, separate and measure platinum(IV) by UV-visible spectrophotometry at the microgram level. Following 5 min of heating the reaction mixture in a water bath, Pt(IV)-TEHBA complex formed. This complex was formed in the presence of potassium iodide solution with a molar absorption coefficient 1.9 × 103 dm3mol-1cm-1. At 420nm, the substance exhibited the greatest absorption. As Beer's law described, the Pt(IV)-TEHBA complex for platinum(IV) has a beer's range of 10-50μgcm-3. It was determined that the proportion ratio of the Pt(IV)-TEHBA complex was 1:1 after its extraction. Despite the investigation of interference from various ions, it was ascertained that the method exhibited selectivity exclusively towards platinum(IV). The trace amounts of platinum(IV) were extracted and quantified from synthetic mixtures representing alloys, binaries and ternary synthetic mixtures. The process of extracting platinum(IV) from pharmaceutical samples involves the implementation of a specific method. Moreover, the procedure exhibits a progressive segregation of palladium(II), platinum(IV) and nickel(II) while also boasting its ease of operation.