Internal Angle Research Articles

Determination of the flexoelectric coefficient in nematic liquid crystals by using fully leaky optical guided mode

ABSTRACT Fully leaky optical-guided mode is employed to determine the difference of the splay and bend flexoelectric coefficient e 1−e 3 in negative nematic Liquid crystal (LC) MS-N0130-000. The theoretical curves of reflected signals versus internal angle are obtained by using elastic continuum theory under two-dimensional electric field and multi-layer optical theory of LC. The experimental curves of reflected signals versus internal angle are obtained by using the fully leaky optical-guided wave technique when alternating current (AC) and direct current (DC) were applied on the Hybrid aligned nematic in-plane switching (HAN-IPS) LC cell respectively. The approximate value of the flexoelectric coefficient e 1−e 3 of MS-N01300-000 is 5.5 × 10−11C/m, which is obtained by comparing theoretical curves with experimental curves.

Efficacy of auxetic lattice structured shoe sole in advancing footwear comfort-From the perspective of plantar pressure and contact area.

Designing footwear for comfort is vital for preventing foot injuries and promoting foot health. This study explores the impact of auxetic structured shoe soles on plantar biomechanics and comfort, motivated by the integration of 3D printing in footwear production and the superior mechanical properties of auxetic designs. The shoe sole designs proposed in this study are based on a three-dimensional re-entrant auxetic lattice structure, orthogonally composed of re-entrant hexagonal honeycombs with internal angles less than 90 degrees. Materials fabricated using this lattice structure exhibit the characteristic of a negative Poisson's ratio, displaying lateral expansion under tension and densification under compression. The study conducted a comparative experiment among three different lattice structured (auxetic 60°, auxetic 75° and non-auxetic 90°) thermoplastic polyurethane (TPU) shoe soles and conventional polyurethane (PU) shoe sole through pedobarographic measurements and comfort rating under walking and running conditions. The study obtained peak plantar pressures (PPPs) and contact area across seven plantar regions of each shoe sole and analyzed the correlation between these biomechanical parameters and subjective comfort. Compared to non-auxetic shoe soles, auxetic structured shoe soles reduced PPPs across various foot regions and increased contact area. The Auxetic 60°, which had the highest comfort ratings, significantly lowered peak pressures and increased contact area compared to PU shoe sole. Correlation analysis showed that peak pressures in specific foot regions (hallux, second metatarsal head, and hindfoot when walking; second metatarsal head, third to fifth metatarsal head, midfoot, and hindfoot when running) were related to comfort. Furthermore, the contact area in all foot regions was significantly associated with comfort, regardless of the motion states. The pressure-relief performance and conformability of the auxetic lattice structure in the shoe sole contribute to enhancing footwear comfort. The insights provided guide designers in developing footwear focused on foot health and comfort using auxetic structures.

Pressure-Reducing Design of 3D-Printed Diabetic Shoe Midsole Utilizing Auxetic Lattice Structure

With the global rise in the prevalence of diabetes, diabetic patients need innovative footwear designs to reduce the risk of foot ulcers. This study examined the mechanical properties of diabetic shoe midsoles featuring auxetic lattice structures. Through the construction of finite element models and simulation, this research compared the biomechanical parameter differences in the plantar regions of the metatarsal head, midfoot, and hindfoot when wearing two types of auxetic midsoles with internal angles of 60° and 75° and a non-auxetic midsole with an internal angle of 90° under both walking and running conditions. Compared to the non-auxetic midsole, the auxetic midsoles significantly reduced the peak plantar pressure and optimized the pressure distribution across various plantar regions. Notably, the auxetic 60° midsole reduced the peak plantar pressure by 19.68–55.25% and 16.19–54.39% compared to the non-auxetic 90° midsole during walking and running, respectively. This study also verified that the auxetic midsoles exhibited greater adaptability and compliance to the plantar foot shape, contributing to reductions in plantar pressure in comparisons of deformation values and plantar contact areas across the different midsoles. Auxetic midsoles manufactured using 3D printing technology have significant potential to prevent diabetic foot ulcers and maintain human foot health. This research integrates insights and techniques from materials science and ergonomics, offering a new direction for footwear design.

Accuracy and feasibility in building a personalized 3D printed femoral pseudoaneurysm model for endovascular training.

The use of three-dimensional(3D) printing is broadly across many medical specialties. It is an innovative, and rapidly growing technology to produce custom anatomical models and medical conditions models for medical teaching, surgical planning, and patient education. This study aimed to evaluate the accuracy and feasibility of 3D printing in creating a superficial femoral artery pseudoaneurysm model based on CT scans for endovascular training. A case of a left superficial femoral artery pseudoaneurysm was selected, and the 3D model was created using DICOM files imported into Materialise Mimics 22.0 and Materialise 3-Matic software, then printed using vat polymerization technology. Two 3D-printed models were created, and a series of comparisons were conducted between the 3D segmented images from CT scans and these two 3D-printed models. Ten comparisons involving internal diameters and angles of the specific anatomical location were measured. The study found that the absolute mean difference in diameter between the 3D segmented images and the 3D printed models was 0.179±0.145 mm and 0.216±0.143mm, respectively, with no significant difference between the two sets of models. Additionally, the absolute mean difference in angle was 0.99±0.65° and 1.00±0.91°, respectively, and the absolute mean difference in angle between the two sets of data was not significant. Bland-Altman analysis confirmed a high correlation in dimension measurements between the 3D-printed models and segmented images. Furthermore, the accuracy of a 3D-printed femoral pseudoaneurysm model was further tested through the simulation of a superficial femoral artery pseudoaneurysm coiling procedure using the Philips Azurion7 in the angiography room. 3D printing is a reliable technique for producing a high accuracy 3D anatomical model that closely resemble a patient's anatomy based on CT images. Additionally, 3D printing is a feasible and viable option for use in endovascular training and medical education. In general, 3D printing is an encouraging technology with diverse possibilities in medicine, including surgical planning, medical education, and medical device advancement.

Sequential Assessment of External Nasal Deviation Angle Changes in Patients With a Deviated Nose Who Underwent Bilateral Osteotomy.

A deviated nose is traditionally classified as bony, cartilaginous, or combined deviation. Osteotomy is commonly used to correct bony deviation, and accurate surgical techniques and postoperative patient management are important for favorable outcomes. The authors investigated the change in the external nasal deviation angle over time using sequential clinical photographs to identify the optimal postoperative follow-up duration. Medical records and sequential standardized clinical photographs of 22 patients who underwent bilateral medial and lateral osteotomies without dorsal augmentation from January 1, 2014 to May 31, 2021, were retrospectively reviewed. Clinical photographs were classified into 4 periods: "a" preoperative, "b" postoperative day (POD) ≤3 weeks, "c" POD ≤9 weeks, and "d" POD >9 weeks. The angle of deviation (AoD) was measured in both frontal and chin-on-chest views for each period. Differences in AoD between temporally adjacent periods were analyzed. Nineteen men and 3 women (mean age: 28.8y) were included. Thirteen patients showed rightward deviation, whereas 9 showed leftward deviation. Eleven patients underwent surgery through an endonasal approach, whereas the other 11 underwent surgery through an external approach. In the frontal view, AoD differences (mean ± SD) between periods "a" and "b," "b" and "c," and "c" and "d" were 5.79 ± 3.36 degrees (P < 0.001), 1.44 ± 1.14 degrees (P < 0.001), and 1.07 ± 1.24 degrees (P < 0.05), respectively. In the chin-on-chest view, the values were 5.17 ± 2.69 degrees (P < 0.001), 2.06 ± 2.63 degrees (P < 0.001), and 1.46 ± 1.31 degrees (P < 0.001), respectively. No statistically significant difference in AoD differences was observed between the two approaches. Angle of deviation can change even 9 weeks after bilateral osteotomy. Thus, long-term follow-up using sequential clinical photographs is mandatory. If needed, close follow-up with early postoperative interventions may be required. The chin-on-chest view showed better sensitivity for assessing AoD than the frontal view.

Clinical and biomechanical characteristics of responders and non-responders to insoles in individuals with excessive foot pronation during walking

This study aimed to identify the clinical and biomechanical factors of subjects with excessive foot pronation who are not responsive (i.e., “non-responders”) to medially wedged insoles to increase knee adduction external moment. Ankle dorsiflexion range of motion, forefoot-shank alignment, passive hip stiffness, and midfoot passive resistance of 25 adults with excessive bilateral pronation were measured. Also, lower-limb angles and external moments were computed during walking with the participants using control (flat surface) and intervention insoles (arch support and 6° medial heel wedge). A comparison between “responders” (n = 34) and “non-responders” (n = 11) was conducted using discrete and continuous analyses. Compared with the responders, the non-responders had smaller forefoot varus (p = 0.014), larger midfoot passive internal torque peak (p = 0.005), and stiffness measured by the torsimeter (p = 0.022). During walking, non-responders had lower angle peaks for forefoot eversion (p = 0.001), external forefoot rotation (p = 0.037), rearfoot eversion (p = 0.022), knee adduction (p = 0.045), and external hip rotation (p = 0.022) and higher hip internal rotation angle peak (p = 0.026). Participants with small forefoot varus alignment, large midfoot passive internal torque, stiffness, small knee valgus, hip rotated internally, and foot-toed-in during walking did not modify the external knee adduction moment (“non-responders”). Clinicians are advised to interpret these findings with caution when considering the prescription of insoles. Further investigation is warranted to fully comprehend the response to insole interventions among individuals with specific pathologies, such as patellofemoral pain and knee osteoarthritis (OA).

Postural Control During Single-Leg Landing in Female Athletes After Anterior Cruciate Ligament Reconstruction.

Secondary anterior cruciate ligament (ACL) injury is a complication of ACL reconstruction (ACLR), which may result from altered neuromuscular control affecting anticipatory postural adjustments (APAs) and compensatory postural adjustments (CPAs) required for maintaining balance during movement. However, it remains unclear how APAs and CPAs differ in single-leg landings post-ACLR compared to healthy subjects. The purpose of this study was to clarify the differences in muscle activities of APAs and CPAs, lower limb kinematics, and kinetics between athletes with a history of ACLR and healthy athletes during single-leg landing. Cross-sectional study. Eighteen female athletes were recruited and divided into ACLR (n = 9) and control groups (n = 9). The experimental task involved a single-leg landing from a 30 cm box. Joint angles and moments were determined using a 3-dimensional motion analysis system, while muscle activity was assessed using surface electromyography. Analysis intervals were divided into two phases: the APA phase (-150 ms to 50 ms) and the CPA phase (50 ms to 250 ms), with initial contact (0 ms) as the reference point. Muscle activity onset time was defined as the time when the baseline exceeded by the sum of mean values and 2 standard deviations. No significant differences were observed in muscle activity or onset time between the ACLR and control groups. However, an increased hip external rotation moment was observed during the CPA phase in the ACLR group. These findings suggest that APAs and CPAs of athletes who returned to sports more than 1 year post-ACLR may be similar. The increased hip external rotation moment in the ACLR group during the CPA phase could represent a specific compensatory strategy to decrease the hip internal rotation angle post-ACLR. III.

Elastic Stable Intramedullary Nailing in Length Stable Versus Unstable Pediatric Femoral Shaft Fractures: A Comparison of Clinical, Radiographic, and Pedobarographic Outcomes.

Pediatric diaphyseal femoral fracture (PDFF) is one of the most common injuries requiring hospitalization. Elastic stable intramedullary nailing (ESIN) is commonly used for PDFFs in ages 5 to 11. The optimal treatment method for length unstable PDFF is a subject of ongoing debate. This study aimed to compare clinical, radiographic, and pedobarographic outcomes of ESIN between length stable and unstable PDFF. We retrospectively reviewed patients undergoing ESIN treatment for isolated PDFF between 2016 and 2021. Exclusion criteria were (1) history of ipsilateral or contralateral lower extremity fractures, (2) highly comminuted or segmental fractures, (3) body weight >50kg, and (4) comorbidities affecting bone quality, range of motion, or neurologic status. The patients were divided into 2 groups according to length stability. Clinical, radiographic, and pedobarographic data were then assessed to compare groups. Twenty-five patients were included (17 length stable and 8 length unstable PDFF) with a mean age of 73.6±17.8 months. There was no significant difference between groups in age, side of injury, body weight, follow-up duration, and nail-canal diameter ratio. Mean deformity in the fracture site in the early postoperative x-rays was not significantly different between groups ( P =0.661). After a mean follow-up of 27.8±14.2 months (range, 12-67), there was no significant difference in mechanical axis deviation, distal femur joint orientation angle, or limb-length discrepancy in both groups. The pedobarographic assessment revealed that the length unstable group had a significantly higher external foot progression angle in the injured extremity (9.8°±6.9° vs. 1.3°±5.6°, P =0.031). However, the length stable group had no significant difference in the foot progression angle (4.9°±5° vs. 3°±4.3°, P =0.326). There was no significant difference in either group for other pedobarographic parameters. ESIN is a safe and effective option for length-unstable PDFF, yet attention should be paid to the rotational alignment. Although significant external rotation deformity occurs in length-unstable PDFF, it has no implications for the other pedobarographic parameters. Level IV.

Precise Characterization of a Waveguide Fiber Interface in Silicon Carbide.

Spin-active optical emitters in silicon carbide are excellent candidates toward the development of scalable quantum technologies. However, efficient photon collection is challenged by undirected emission patterns from optical dipoles, as well as low total internal reflection angles due to the high refractive index of silicon carbide. Based on recent advances with emitters in silicon carbide waveguides, we now demonstrate a comprehensive study of nanophotonic waveguide-to-fiber interfaces in silicon carbide. We find that across a large range of fabrication parameters, our experimental collection efficiencies remain above 90%. Further, by integrating silicon vacancy color centers into these waveguides, we demonstrate an overall photon count rate of 181 kilo-counts per second, which is an order of magnitude higher compared to standard setups. We also quantify the shift of the ground state spin states due to strain fields, which can be introduced by waveguide fabrication techniques. Finally, we show coherent electron spin manipulation with waveguide-integrated emitters with state-of-the-art coherence times of T 2 ∼ 42 μs. The robustness of our methods is very promising for quantum networks based on multiple orchestrated emitters.

Study on Evaluation and Prediction for Shale Gas PDC Bit in Luzhou Block Sichuan Based on BP Neural Network and Bit Structure

Deep and ultra-deep shale gas resources have great potential, but well drilling faces many challenges. The Polycrystalline Diamond Compact (PDC) bit has become the primary rock-breaking instrument for oil and gas drilling. Reasonable bit structure designs can promote rock-breaking efficiency and extend service life. In this study, reverse modeling technology is used to analyze the structural characteristics of PDC bits collected in the field, and the influence of the structural characteristics of the bit at a specific interval on the rate of penetration (ROP) and drill footage is investigated using the Spearman rank correlation coefficient method. The number of blades, cutting angle of the cutters, crown rotation radius, internal cone angle, and diameter of the cutters are discovered to be the main structural characteristics that affect the ROP and footage of the bits, and the degree of influence varies depending on the formation conditions. The number of blades, crown rotation radius, inner cone angle, and cutting angle of the cutters have a significant impact on the ROP, whereas blade thickness, gauge length, gauge width, nozzle equivalent diameter have a significant impact on the bit footage. In addition, a back propagation (BP) neural network is utilized to build a prediction model of bit footage and ROP over a certain interval based on the structural characteristics of the bit. The goodness of fit of the model is greater than 85%, and its accuracy is high. Based on the usage of the bit, the evaluation and prediction of the bit can provide a reference for the structural design and optimization of the bit in a specific interval, guide the bit selection work, rationally plan the drilling operation, and reduce the drilling cost.

Walking and Running of Children with Decreased Femoral Torsion.

Understanding the implications of decreased femoral torsion on gait and running in children and adolescents might help orthopedic surgeons optimize treatment decisions. To date, there is limited evidence regarding the kinematic gait deviations between children with decreased femoral torsion and typically developing children, as well as the implications of the same on the adaptation of walking to running. A three-dimensional gait analysis study was undertaken to compare gait deviations during running and walking among patients with decreased femoral torsion (n = 15) and typically developing children (n = 11). Linear mixed models were utilized to establish comparisons within and between the two groups and investigate the relationship between clinical examination, spatial parameters, and the difference in hip rotation between running and walking. Patients exhibited increased external hip rotation during walking in comparison to controls, accompanied by higher peaks for the same as well as for knee valgus and external foot progression angle. A similar kinematic gait pattern was observed during running, with significant differences noted in peak knee valgus. In terms of variations from running to walking, patients internally rotated their initially externally rotated hip by 4°, whereas controls maintained the same internal hip rotation. Patients and controls displayed comparable kinematic gait deviations during running compared to walking. The passive hip range of motion, torsions, and velocity did not notably influence the variation in mean hip rotation from running to walking. This study underlines the potential of 3D gait kinematics to elucidate the functional implications of decreased FT and, hence, may contribute to clinical decision making.

Biomechanical mechanisms of anterior cruciate ligament injury in the jerk dip phase of clean and jerk: A case study of an injury event captured on-site

BackgroundWeightlifting exposes athletes to significant loads, potentially placing the knee joint in an abnormal mechanical environment and leading to anterior cruciate ligament (ACL) injuries. Once an ACL injury occurs, it can affect athletes’ competitive ability to varying degrees and even prematurely end their career. Understanding the biomechanical mechanisms of ACL injuries in weightlifters helps in comprehensively understanding the stress patterns and degrees on ACL during human movement, and identifying potential injury-causing factors, thereby enabling the implementation of appropriate preventive measures to reduce the occurrence of injuries. This study aimed to explore the biomechanical mechanisms of ACL injuries during the jerk dip phase of clean and jerk in weightlifters, providing a theoretical basis for the prevention of ACL injuries in weightlifting sports. MethodsThis study utilized the German SIMI Motion 10.2 movement analysis system and the AnyBody simulation system to analyze the kinematic and dynamic parameters of a 109 kg + class weightlifter (height: 191 cm, age: 22 years, weight: 148 kg, athletic level: elite) performing a 205 kg clean and jerk (non-injured) and a 210 kg clean and jerk (ACL injury occurred). The differences in kinematic and dynamic indicators of lower limb joints under injured and non-injured jerk dip conditions were investigated. ResultsKnee joint torque during non-injured clean and jerk was consistently positive (i.e., external rotation) but turned from positive to negative (i.e., from external rotation to internal rotation) during injured clean and jerk and reached a maximum internal rotation torque of 21.34 Nm at the moment of injury. At every moment, the muscle activation and simulated muscle force of the quadriceps and gastrocnemius during the injured clean and jerk were higher than those during the non-injured clean and jerk. By contrast, the muscle activation and simulated muscle force of the semitendinosus, semimembranosus, biceps femoris, and soleus during non-injured clean and jerk were higher than those during injured clean and jerk. The knee joint internal rotation angle during injured clean and jerk first increased and then declined, reaching a peak at 46.93° at the moment of injury, whereas it gradually increased during non-injured clean and jerk. The proximal tibia on the left side during the injured clean and jerk moved forward faster by 0.76 m/s compared with that during the non-injured clean and jerk. ConclusionsThe small muscle activation and simulated muscle force of the hamstring and soleus could not resist timely and effectively the large muscle activation and simulated muscle force of the quadriceps (especially the medial quad) and gastrocnemius. As such, the force applied to the ACL could exceed its ultimate load-bearing capacity. Kinematic indicators in the athlete's injured lift demonstrated certain disparities from those in their non-injured lift. Knee internal rotation and tibial anterior translation during the jerk dip phase of weightlifting might be the kinematic characteristics of ACL injuries.

On tiling spherical triangles into quadratic subpatches

Various interpolation and approximation methods arising in several practical applications in geometric modeling deal, at a particular step, with the problem of computing suitable rational patches (of low degree) on the unit sphere. Therefore, we are concerned with the construction of a system of spherical triangular patches with prescribed vertices that globally meet along common boundaries. In particular, we investigate various possibilities for tiling a given spherical triangular patch into quadratically parametrizable subpatches. We revisit the condition that the existence of a quadratic parameterization of a spherical triangle is equivalent to the sum of the interior angles of the triangle being π, and then circumvent this limitation by studying alternative scenarios and present constructions of spherical macro-elements of the lowest possible degree. Applications of our method include algorithms relying on the construction of (interpolation) surfaces from prescribed rational normal vector fields.

Development of Z number-based fuzzy inference system to predict bearing capacity of circular foundations

Precise bearing capacity prediction of circular foundations is essential in civil engineering design and construction. The bearing capacity is affected by factors such as depth, density of soil, internal angle of friction, cohesion of soil, and foundation radius. In this paper, an innovative perspective on a fuzzy inference system (FIS) was proposed to predict bearing capacity. The uncertainty of fuzzy rules is eliminated by using Z-number theory. The effective parameters, i.e., depth, density of soil, internal angle of friction, cohesion of soil, and foundation radius were considered as inputs to the proposed model. To compare regression and FIS model with Z-based FIS, statistical indices such as the coefficient of determination (R2), root mean square error (RMSE), and variance account for (VAF) were employed. For training and testing Z-FIS, the R2 was (0.977 and 0.971), the RMSE was (1.645 and 1.745), and the VAF was (98.549% and 98.138), whereas for the FIS method, the values were (0.912 and 0.904), (5.962 and 6.76), and (90.12% and 88.49%). It should be mentioned that Z theory decreased the computational time by 89.28% (174.04 s to 18.65 s). The comparison of the statistical indicators of the presented models revealed the superiority of the Z-FIS model over the FIS. Notably, sensitivity analysis revealed that the most effective parameters on bearing capacity are internal angle of friction, depth, and soil density.

Effects of running-induced fatigue on joint kinematics and kinetics during overground running: a systematic review and meta-analysis.

This study evaluated the acute fatigue-inducing effect of distance running on kinematics and kinetics during overground running. Standardised mean differences (SMD) with 95% confidence intervals (95% CI) were used to pool data across 16 studies. Effects during consistent (pre- and post-fatigue running speed within ± 5%) versus varied speed running (difference of >5% between running speeds) were analysed separately. There was strong evidence that running-induced fatigue significantly increases ground contact times at consistent running speeds (SMD 0.52 [95% CI 0.22, 0.82]) and moderate evidence that step length shortens at varied running speeds (SMD -1.27 [95% CI -1.79, -0.75]). There was strong evidence that fatigue does not change peak: hip and knee flexion angles, hip adduction angle, hip and knee internal rotation angles, hip and knee extension moments, hip and knee abduction moments, knee abduction angle, knee flexion and extension moments, knee adduction moment, rearfoot eversion angle, and plantarflexion moments, or knee flexion and plantarflexion range of motion during stance. Running-induced fatigue increases contact times and reduces step length, whereas lower-body joint angles and moments are unchanged. Minimising changes in stride parameters could provide a mechanism for reducing the effects of fatigue on running performance.

Smooth morphing of immersed spherical curves and application to ruled surfaces

In this paper, we realize a rapid, smooth iterative morphing algorithm between two immersed and closed spherical curves of arbitrary turning numbers. By compensating in turning numbers, we linearly interpolate between geodesic curvatures and the side lengths of their accurate spherical polygons approximation. Our algorithm is essentially based on a geometrical closure condition for a flow of spherical polygons involving the variation of both sides and exterior angles. A curvature smoothing flow using discrete geodesic curvature is adopted for smooth curve generation. To demonstrate the good properties of the method, a morphing of spherical curves and ruled surfaces is illustrated.

Structural optimization of thermal management system for bionic liquid cold battery based on fuzzy grey correlation analysis

An energy-efficient battery thermal management system with efficient enhanced heat transfer characteristics, low power consumption and backflow inhibition performance is of great importance for electric vehicle power batteries. Based on the design of the Tesla valve and inspired by bionics, a new type of bionic blade-like mini-channel liquid cold plate with high efficiency, low power consumption and certain anti-reverse flow performance was proposed. Firstly, the initial liquid-cooled plate thermal simulation model at 5C discharge was established by CFD method and its reliability was verified by experiment. Then, orthogonal tests and fuzzy correlation analysis (FGRA) were used as evaluation methods to analyze the effects of four structural parameters (inner angle α, circumcenter angle θ1, circumcenter angle θ2, and channel height d) on the average temperature, heat transfer coefficient, and friction coefficient. The results show that the variation of the channel height d had the highest degree of influence on the mean temperature (Tave) and friction coefficient f, and that the internal angle α had the highest correlation with the heat transfer coefficient h. Finally, based on the optimization results, a better model within the range of values of each factor was obtained. When α = 25°, θ1 = 90°,θ2 = 75°, and d = 1.2 mm, Nu was increased by 0.932 (95.08 %), and ΔP was decreased by 501.686 Pa (84.74 %).The results of the optimization were shown in the following table.

Sensitivity analysis of gyratory compactor variables to mimic roller compacted concrete pavement performance

ABSTRACT The compaction parameters suggested for Superpave gyratory compactor by ASTM C1800 are primarily derived from the asphalt mix (ASTM D6925). Since the rheological behaviour of Roller Compacted Concrete Pavement (RCCP) is significantly different from asphalt mixes, conventional Superpave compaction parameters cannot be directly adopted for RCCP. Hence, the current study focuses on formulating compaction parameters for the design of RCCP to resemble the field behaviour. For this task, response surface methodology was employed to investigate the effect of gyratory compactor parameters such as internal angle (0.82–3°), compaction pressure (600–1000 kPa), and gyration levels (60–120) on the performance of RCCP specimens. The accuracy of the response prediction model was verified with ANOVA analysis. Further, multiobjective optimization was performed and validated with experimental findings. For validation of laboratory findings, a field test section was constructed using a duplex roller (dual drum vibratory roller). The results showed that the ASTM C1800 suggested gyratory parameters resulted in lower fresh density and strength properties of 4% and 7–45%, respectively, than the field specimens. However, the specimens fabricated at 1.92° internal angle, 120 gyrations, 1000 kPa, and 1 aspect ratio in the gyratory compactor could provide comparable field properties.

Bone morphology and physical characteristics of the pro-cyclist hip joint

PurposeThis study aimed to investigate the radiographic findings for the hip joint and hip range of motion in professional cyclists, and to determine their bone morphology and physical characteristics. The effects of physical characteristics on athletic performance were examined in terms of metabolic efficiency using simulation analysis.MethodsWe performed a case–control research study on 22 hips in 11 male professional cyclists (average age 28.5, height 1.73 m, weight 77.6 kg). Thirty hips in 15 healthy male volunteers were selected as controls. As radiographic evaluations, acetabular dysplasia was assessed on standardized radiographs. During physical evaluations, the hip range of motion was examined. We used simulation analysis to investigate the metabolic efficiency in the different cycling forms.ResultsThe radiographic evaluations showed a significant difference in the incidence of acetabular dysplasia (p = 0.01): 59% (13/22 hips) in the pro-cyclist group versus 10% (3/30 hips) in the control group. The physical evaluations revealed significant differences in the hip internal rotation angle (p = 0.01), with greater ranges of internal rotation in the pro-cyclist group versus the control group. The simulation analyses showed that metabolism was reduced in the cycling form with hip internal rotation, especially in the lower extremities.ConclusionsPro-cyclists showed a high frequency of acetabular dysplasia and superior hip internal rotation. According to the cycling model analyses, hip internal rotation allowed pedaling with reduced metabolic power.

A biomechanical report of an acute lateral ankle sprain during a handball-specific cutting movement

ABSTRACT Biomechanical measurements of accidental ankle sprain injuries are rare but make important contributions to a more detailed understanding of the injury mechanism. In this case study, we present the kinematics and kinetics of a lateral ankle sprain of a female athlete performing handball-specific fake-and-cut manoeuvres. Three-dimensional kinematics and kinetics were recorded and six previously performed trials were used as reference. Plantarflexion, inversion, and internal rotation angles were substantially larger than the reference trials and peaked between 190 and 200 ms after initial ground contact. We observed a highly increased inversion and internal rotation moment. However, compared to the non-injury trials the data also revealed a reduction in the second dorsiflexion moment peak. Ground reaction forces were lower throughout the injury trial. Other parameters at initial ground contact including ankle and hip position, step length, and the traction coefficient indicate that a preparatory maladjustment occurred. This study adds valuable contributions to the understanding of lateral ankle sprains by building upon previously published reports and considering the shoe-surface interaction as an important factor for injury.