Intensity Modulation Direct Detection Research Articles

Mixed domain coherent link with electrically reconfigurable IMDD and coherent modes for O-band data center applications

We report the first O-band link with electrically reconfigurable intensity-modulation direct-detection (IMDD) and coherent operation using custom silicon photonic chips packaged with commercial electronic chips. Transmission below the KP4-FEC threshold is shown using commercial 53 Gbaud PAM4 digital signal processing (DSP) for 16QAM (200 Gbps/λ) and PAM4 (100 Gbps/λ). Efficient operation of the packaged full link at 12 and 11.2 pJ/bit is achieved for the PAM4 and 16QAM modes, respectively.

Bias-aided DD-LMS equalizer for optical multipath-interference-impaired high-speed PAM4 transmission systems

Multipath interference (MPI) noise induces drastic fluctuations in high-speed 4-level pulse amplitude modulation (PAM4) intensity modulation direct detection (IMDD) systems, severely degrading the transmission performance. Here, we propose a bias-aided decision-directed least mean square (DD-LMS) equalizer to eliminate the MPI noise. In the simulation, the proposed bias-aided DD-LMS equalizer could adeptly track and compensate the MPI-impaired PAM4 signal, markedly improving the bit error rate (BER) performance under different MPI levels and laser linewidths. Within a 112 Gbps PAM4 transmission system, the proposed equalizer achieves a MPI tolerance over 4 dB at the KP4-forward error correction (FEC) threshold (2.4 × 10−4), outperforming existing MPI suppression techniques.

12.1 terabit/second data center interconnects using O-band coherent transmission with QD-MLL frequency combs

Most current Data Center Interconnects (DCI) use intensity modulation direct detection (IMDD) configurations due to their low complexity and cost. However, significant scaling challenges allow coherent solutions to become contenders in these short reach applications. We present an O-band coherent optical fiber transmission system based on Quantum Dot—Mode Locked Lasers (QD-MLLs) using two independent free-running comb lasers, one each for the carrier and the Local Oscillator (LO). Using a comb-to-comb configuration, we demonstrate a 10 km single mode fiber, O-band, coherent, heterodyne, 12.1 Tbps system operating at 0.47 Tbps/λ using 26 λs. We used fewer comb lines (26 λs), faster symbol rate (56 GBaud) and higher constellation cardinality (32 QAM) relative to the highest capacity C-band systems reported to date. Through design, analysis, and experimentation, we quantify the optimum comb line spacing for this use case. We compare potential configurations for increasing data center interconnect capacities whilst reducing power consumption, complexity, and cost.

Enhanced ABLO-OFDM performance by using composite multi-mode index modulation in IM/DD systems

In intensity modulation direct detection (IM/DD) systems, an adaptively biased layered optical orthogonal frequency division multiplexing (ABLO-OFDM) scheme is proposed based on composite multi-mode index modulation (CMM-IM). The ABLO-OFDM has a simple structure, easy demodulation, low complexity, and effectively reduces the peak-to-average power ratio (PAPR). Since CMM-IM extends the index to the constellation domain, it increases the number of index bits to further improve the spectral efficiency (SE). By dynamically adjusting the number of activated subcarriers and the number of layers, various signal power can be achieved to enhance system flexibility and reliability. The system performance of four schemes is compared and analyzed in IM/DD systems. The result shows that, for the same SE, CMM-ABLO (4,3) achieves a 3 dB receiver sensitivity gain compared with CMM-ABLO (8,2). When L is 3, four schemes can transmit over about 50 km single-mode fiber under the soft decision forward error correction (SD-FEC) threshold. When L is 1 and the sample rate is less than 20 GSa/s, both CMM-ABLO (4,2) and CMM-ABLO (4,3) can achieve error-free transmission. Moreover, as the number of layers increases, PAPR decreases and it reaches a maximum reduction of 9.6 dB.

Concurrent performance and security enhancement of ultrahigh-order DSM signals via null subcarriers.

In this paper, we propose leveraging null subcarriers in discrete multi-tone modulation (DMT) to process the DMT signal in both time and frequency domains. Additionally, we employ discrete memory enhanced chaos (DMEC) to scramble the signal in the frequency domain, thereby achieving physical layer signal encryption while ensuring a more uniform power distribution in the time-domain waveform. In our experimental demonstration, we achieved high-security transmission of a DSM-based 65536-QAM signal at a data rate of 16.01 Gb/s over a 25 km single-mode fiber (SMF) in an intensity-modulation direct-detection (IMDD) system. Additionally, in the transmission experiments for 13684-QAM and 65536-QAM signals, the proposed method demonstrated a receiver sensitivity gain of over 0.5 dB compared to the traditional DSM-based ultrahigh-order transmission.

Advanced Neural Network-Based Equalization in Intensity-Modulated Direct-Detection Optical Systems: Current Status and Future Trends

Intensity-modulated direct-detection (IM/DD) optical systems are most widely employed in short-reach optical interconnects due to their simple structure and cost-effectiveness. However, IM/DD systems face mixed linear and nonlinear channel impairments, mainly induced by the combination of square-law detection and chromatic dispersion, as well as the utilization of low-cost non-ideal transceivers. To solve this issue, recent years have witnessed a growing trend of introducing machine learning technologies such as neural networks (NNs) into IM/DD systems for channel equalization. NNs usually present better system performance than traditional approaches, and various types of NNs have been investigated. Despite the excellent system performance, the associated high computational complexity is a major drawback that hinders the practical application of NN-based equalizers. This paper focuses on the performance and complexity trade-off of NNs employed in IM/DD systems, presenting a systematic review of the current status of NN-based equalizers as well as a number of effective complexity reduction approaches. The future trends of leveraging advanced NN in IM/DD links are also discussed.

Fractionally spaced nonlinear Tomlinson-Harashima precoding with weight clustering for C-band 100 Gbaud/λ PAM-4 transmission.

A nonlinear Tomlinson-Harashima precoding (NTHP) scheme has been verified for its capability to effectively address both the linear and nonlinear inter-symbol interferences (ISIs) arising in the intensity-modulation direct-detection (IM-DD) fiber optics transmission. Nevertheless, the application of the NTHP scheme may significantly increase the number of levels for the intensity modulated signals, resulting in the reduction of both eye width and receiver sensitivity. Here, we propose a fractionally spaced NTHP with a weight clustering (FS-NTHP-WC) scheme. Consequently, an accurate ISI feedback can be obtained to enlarge the eye width; meanwhile a hardware-efficient implementation without the equalization penalty can be achieved by weight clustering and pruning. When the C-band 100 Gbaud/λ PAM-4 signals are transmitted, our proposed FS-NTHP-WC scheme not only can achieve 0.25 dB and 0.5 dB gains of receiver sensitivity under back-to-back (B2B) and 2-km standard single-mode fiber (SSMF) transmission conditions, respectively, but can also cut down the computational complexity by 90% and 76% in terms of the number of multiplications and additions, respectively, in comparison with the NTHP scheme.

Weight-adaptive joint mixed-precision quantization and pruning for neural network-based equalization in short-reach direct detection links.

Neural network (NN)-based equalizers have been widely applied for dealing with nonlinear impairments in intensity-modulated direct detection (IM/DD) systems due to their excellent performance. However, the computational complexity (CC) is a major concern that limits the real-time application of NN-based receivers. In this Letter, we propose, to our knowledge, a novel weight-adaptive joint mixed-precision quantization and pruning approach to reduce the CC of NN-based equalizers, where only integer arithmetic is taken into account instead of floating-point operations. The NN connections are either directly cutoff or represented by a proper number of quantization bits by weight partitioning, leading to a hybrid compressed sparse network that computes much faster and consumes less hardware resources. The proposed approach is verified in a 50-Gb/s 25-km pulse amplitude modulation (PAM)-4 IM/DD link using a directly modulated laser (DML) in the C-band. Compared with the traditional fully connected NN-based equalizer operated with standard floating-point arithmetic, about 80% memory can be saved at a minimum network size without degrading the system performance. Quantization is also shown to be more suitable to over-parameterized NN-based equalizers compared with NNs selected at a minimum size.

Enhancing secure transmission of ultra-high order QAM via delta-sigma modulation integrated with radial basis function neural network enhanced chaos

This paper proposes and experimentally demonstrates an ultra-high order signal security enhancement method based on delta-sigma modulation (DSM). We employ a radial basis function neural network (RBFnn) to enhance Henon chaos, effectively avoiding the degradation of chaotic dynamics, and increasing the key space from 1054 to 10385. In the experimental demonstration, we achieved high-security transmission of 16384QAM over 25 km in an intensity-modulated direct detection (IMDD) system based on DSM. The experimental results show that the ultra-high order transmission scheme based on RBFNN-chaos and DSM has superior security, with a key sensitivity of up to 10−16.

Enhancing secure transmission and key distribution for ultrahigh-order QAM via delta-sigma modulation and discrete memristive-enhanced chaos.

In this Letter, we propose a method for ultrahigh-order QAM secure transmission and key distribution based on delta-sigma modulation (DSM) and discrete memristive-enhanced chaos (DMEC). The disturbance vectors generated by the DMEC scramble the DSM signals in both frequency and time domains, resulting in highly secure DSM signals. Through the key modulation and power adjustment and then superimposing them on the encrypted signals, the method achieves simultaneous transmission of keys and signals without the need for additional spectral resources. This approach allows for secure communication with continuous key iteration and updates, offering an effective solution for implementing "one-time pad" encryption. In the experimental demonstration, we achieved a secure transmission and key distribution of a 16384QAM signal at a rate of 17.09 Gb/s over 25 km in an intensity-modulated direct detection (IMDD) system, based on DSM.

Adaptive multi-band modulation for robust and low-complexity faster-than-Nyquist non-orthogonal FDM IM-DD systems

Faster-than-Nyquist non-orthogonal frequency-division multiplexing (FTN-NOFDM) has been shown to have good robustness against the steep frequency roll-off in a bandwidth-limited optical communication system. Among various FTN-NOFDM techniques, the non-orthogonal matrix precoding (NOM-p) based FTN has relatively high compatibility, which can easily utilize the existing advanced digital signal processing (DSP) techniques in the conventional OFDM. In this work, we propose what we believe to be a novel FTN-NOFDM scheme with adaptive multi-band modulation. By dividing the single-band NOM-p into multiple-band NOM-p, the proposed scheme is able to assign different quadrature amplitude modulation (QAM) levels to different sub-bands, leading to better utilization of the low-pass-like channel as well as reduced computational complexity. The impacts of sub-band number and bandwidth compression factor on the bit-error-rate (BER) performance and complexity are experimentally analyzed in a 32.23-Gb/s and 20-km intensity modulation-direct detection (IM-DD) optical transmission system. Results show that the proposed scheme with a proper sub-band number can lower the BER and greatly reduce the complexity compared to the conventional single-band scheme.

On the multipath interference mitigation for high-speed IM-DD transmissions with Nyquist subcarrier modulation.

The performance of high-speed intensity modulation direct detection (IM-DD) transmissions is severely degraded due to the occurrence of multipath interference (MPI), especially when a higher-order modulation format is utilized. Here, we propose and demonstrate, for the first time to the best of our knowledge, that a Nyquist subcarrier modulation (Nyquist-SCM) format inherently exhibits resistance to the MPI. We experimentally evaluate the MPI tolerance by transmitting 56 Gbit/s PAM-4 signals and Nyquist-SCM 16QAM signals over the 2 km standard single-mode fiber (SSMF) when the C-band semiconductor laser with a linewidth of 1.7 MHz is utilized. In comparison with the PAM-4 format, the Nyquist-SCM 16QAM format can lead to an enhanced MPI tolerance of 4 dB at the KP4-FEC threshold of BER = 2 × 10-4. In addition, even with the help of MPI mitigation for the PAM-4 signals based on two newly reported methods, the utilization of Nyquist-SCM 16QAM signal can still guarantee an improved MPI tolerance of 1 dB.

Extending the coverage of user-diversified IM-DD PON by FDM: a mathematical model with experimental verification.

Future passive optical networks (PONs) call for more flexibility to support diversified users with various rate demands and link qualities. Using traditional time-division multiplexing (TDM), the concept of a flexible rate PON was proposed to accommodate more users with link diversity by rate adaptation. In this Letter, we reveal the PON coverage can be further extended through frequency-division multiplexing (FDM) in the presence of multiuser diversity, namely, (i) there exist users with frequency-dependent link conditions and (ii) the link conditions exhibit disparity among users. We build a mathematical model and propose an optimization algorithm based on the binary tree search to optimize diversity gain. We experimentally verify its feasibility by studying the diversity gain concerning chromatic dispersion, optical path loss, and signal-to-noise ratio (SNR) variation in a 200G-class intensity-modulation direct-detection (IM-DD) system.

MPLC-based low-modal-crosstalk nine-mode-group demultiplexer for DSP-free IM/DD MDM transmission over MMF

Weakly coupled mode-division multiplexing (MDM) transmission over legacy laid multimode fiber (MMF) has great economic efficiency and can enormously enhance the capacity of short-reach optical interconnections. In order to be compatible with cost-efficient intensity-modulation/direct-detection (IM/DD) transceivers, weakly coupled mode-group demultiplexers that can simultaneously receive each mode group of MMFs are highly desired. In this paper, we propose a scalable low-modal-crosstalk mode-group demultiplexer over MMF based on multiplane light conversion (MPLC). Multiple input Hermite–Gaussian (HG) modes of MMF are first converted to bridging modes that are composed of HG00 modes distributed as a right-angle triangle in Cartesian coordinates, and then each HG00 mode belonging to a degenerate mode group is mapped to different overlapped HGn0 modes with vertical orientation for simultaneous detection. With the help of bridging modes, the MPLC-based mode-group demultiplexer can efficiently demultiplex all mode groups in standard MMFs with less than 20 phase masks. A nine-mode-group demultiplexer is further designed for demonstration, and simulation results show that the MPLC-based demultiplexer achieves low modal crosstalk of lower than −22.3dB at 1550 nm and lower than −17.9dB over the C-band for all the nine mode groups with only 16 phase masks.

Photodetector with a metalens packaging module for visible light communication based on RGBY illumination LED light source

A novel, to the best of our knowledge, photodetector with a metalens packaging module used as the visible light communication (VLC) receiver is proposed and designed. An LED consisting of red, green, blue, and yellow chips (RGBY-LED) is adopted as the transmitter for intensity modulation direct detection VLC systems. A metalens array with a numerical aperture (NA) of 0.707 used as a polarization-insensitive planar lens of the VLC system receiver is designed at wavelengths of 457, 523, 592, and 623 nm corresponding to blue, green, yellow, and red for high efficiency. Compared with a traditional Fresnel lens positive-intrinsic-negative (PIN) photodetector module as the VLC receiver, the introduction of a metalens module can decrease the form factor of the VLC receiver module and, in particular, it is much thinner. The combination of the multi-color LED transmitter and photodetector metalens packaging module receiver can increase the modulation bandwidth due to four different wavelengths used for the VLC system. Finite-difference time domain (FDTD) simulations are performed to validate the performance of the photodetector with a metalens module. It is revealed that the corresponding efficiencies of 57.5%, 55.4%, 57%, and 56.3% were achieved at wavelengths of 623, 592, 523, and 457 nm, respectively, based on a metalens array with a 0.707 NA and 2.5 µm radius of the active area of the photodetector. It is a promising technology for indoor VLC systems such as those for smart phones and other Internet of Things devices due to the need for compact packaging for the receiver.

End-to-end learning strategy based on a frequency domain feature decoupling network emulator with joint probabilistic shaping and equalization for a 300-Gbit/s OAM mode division multiplexing transmission

Mode coupling and device nonlinear impairment appear to be a long-standing challenge in the orbital angular momentum (OAM) mode division multiplexing (MDM) of intensity modulation direct detection (IM/DD) transmission systems. In this paper, we propose an end-to-end (E2E) learning strategy based on a frequency domain feature decoupling network (FDFDnet) emulator with joint probabilistic shaping (PS) and equalization for an OAM-MDM IM/DD transmission with three modes. Our FDFDnet emulator can accurately build a complex nonlinear model of an OAM-MDM system by separating the signal into features from different frequency domains. Furthermore, a FDFDnet-based E2E strategy for joint PS and equalization is presented with the aim of compensating the signal impairment for the OAM-MDM IM/DD system. An experiment is carried out on a 300 Gbit/s carrierless amplitude phase-32 (CAP-32) signal with three OAM modes over a 10 km ring-core fiber transmission, and the results show that the proposed FDFDnet emulator outperforms the traditional CGAN emulator, with improvements in the modelling accuracy of 30.8%, 26.3% and 31% for the three OAM modes. Moreover, the receiver sensitivity of the proposed E2E learning strategy is higher than for the CGAN emulator by 3, 2.5, 2.2 dBm and the real channel by 5.5, 5.1, and 5.3 dBm for the three OAM modes, respectively. Our experimental results demonstrate that the proposed FDFDnet emulator-based E2E learning strategy is a promising contender for achieving ultra-high-capacity interconnectivity between data centers.

High-speed data transmission over a microresonator frequency comb with dispersion compensation for augmented data rates and reach

Abstract Microresonator frequency comb-based high-speed data transmission provides a pathway towards augmented data capacity without increasing the number of laser sources. Their use with intensity-modulated direct detection modulation (IMDD) formats is especially pertinent in data center communications where minimizing cost, latency and complexity is paramount. This however implies that the same extent of digital signal processing techniques commonly used in coherent detection for the management of fiber impairments including chromatic dispersion are not available. With the proliferation of silicon photonics technologies in data center transceivers integrated dispersion compensation which can overcome fiber impairments would be of great merit. We demonstrate low power generation of the primary comb state in a silicon nitride microresonator and transmission of 25 Gb/s NRZ and 50 Gb/s PAM4 data over 20 km of single mode fiber. This represents the longest fiber reach demonstrated to date for the transmission of IMDD data using an integrated, microresonator frequency comb. An integrated, tunable grating device for dispersion compensation that reduces dispersion impairments after several fiber lengths generates significant improvements in the eye diagram, six orders of magnitude improvement in the bit-error rate and 14 dB improvement in the transmitter and dispersion eye closure quaternary values. Concurrently, doubling data transmission is demonstrated via polarization multiplexing a comb line and successful dispersion compensation of up to 20 km.

Time transfer over 113 km free space laser communication channel.

The space time frequency transfer plays a crucial role in applications such as space optical clock networks, navigation, satellite ranging, and space quantum communication. Here, we propose a high-precision space time frequency transfer and time synchronization scheme based on a simple intensity modulation/direct detection (IM/DD) laser communication system, which occupies a communication bandwidth of approximately 0.2%. Furthermore, utilizing an optical-frequency comb time frequency transfer system as an out-of-loop reference, experimental verification was conducted on a 113 km horizontal atmospheric link, with a long-term stability approximately 8.3 × 10-16 over a duration of 7800 seconds. Over an 11-hour period, the peak-to-peak wander is approximately 100 ps. Our work establishes the foundation of the time frequency transfer, based on the space laser communication channel, for future ground-to-space and inter-satellite links.

Pairwise Tomlinson-Harashima precoding for multiple-lane IM-DD transmissions.

As for the photonic interconnection based on the multiple-lane intensity modulation direct detection (IM-DD) transmission, both intra-channel inter-symbol-interference (ISI) originating from bandwidth constraint, and inter-channel performance discrepancy emerging from inter-channel component differences are the major bottleneck for the throughput enhancement. Here, we propose a pairwise Tomlinson-Harshima precoding (P-THP) scheme, in order to simultaneously deal with both intra-channel ISI and inter-channel performance discrepancy. The effective function of the proposed P-THP scheme is experimentally evaluated by transmitting 4-channel 81-GBaud PAM4 signals over 2 km standard single-mode fiber (SSMF). Compared with the conventional scheme with only applying THP on individual wavelength channel, the required optical received power (ROP) under the back-to-back (B2B) transmission can be reduced by 0.75∼1 dB with the help of proposed P-THP in different experimental component configurations, at the 7% hard decision forward error correction (HD-FEC) threshold of BER = 3.8 × 10-3. After the 2 km SSMF transmission, only the use of proposed P-THP can guarantee to reach the designated HD-FEC threshold, leading to a net rate of >600 Gbit/s.

Photonic Gateway accommodating all types of wavelength paths for digital-coherent and IM-DD user terminals in all-photonic metro-access converged networks

In access and metro networks, there is increasing demand for guaranteed wide-bandwidth and stringent/deterministic end-to-end latency characteristics. Converging these networks by expanding dense wavelength-division-multiplexed metro networks to access areas is a promising approach to satisfy this demand. An All-Photonics Metro-Access Converged Network (APN) dynamically and flexibly provides a wavelength connection between any two points including user premises. This evolution in network architecture presents some technical challenges. First, from the access-node architecture viewpoint, conventional reconfigurable optical add/drop multiplexers (ROADMs) do not have functions for remote and in-channel user-terminal (UT) control or turn-back connection within the access area. Therefore, the APN cannot be achieved by simply adopting ROADMs as access nodes, which are defined as Photonic Gateways. Remote and in-channel UT controls are required to control the endpoints of a wavelength path beyond the carrier control-plane network. These types of control should be independent of the protocol and modulation/detection method for the main signal. In addition, the Photonic Gateway must flexibly and efficiently support a new type of wavelength path, specifically a turn-back connection within the access area, due to metro/access convergence. Second, from the viewpoint of the process for dynamic wavelength-path provisioning, the APN controller should autonomously discover physical connectivity between a UT and the Photonic Gateway connected via field access fibers. This paper proposes a novel Photonic Gateway architecture that flexibly and scalably provides various UTs with direct optical connections including turn-back configurations. This paper also proposes a method that autonomously recognizes physical connections between newly connected UTs and the Photonic Gateway. The proposed architecture and method are experimentally verified based on all types of wavelength-path provisioning that take at most 72 s using Photonic Gateway prototypes, 100-Gb/s digital-coherent UTs, and 10-Gb/s intensity-modulation direct-detection UTs. All types of wavelength paths that are provided over the APN architecture are considered including a turn-back connection between two UTs within the same access area and connections between two UTs that traverse the metro area with or without optical/electrical conversion.