Intensity Modulation And Direct Detection Research Articles

Gradient-descent noise whitening techniques for short-reach IM-DD optical interconnects with severe bandwidth limitation.

Bandwidth limitation in optoelectrical components and the chromatic dispersion-induced power fading phenomenon cause severe inter-symbol interference (ISI) in high-speed intensity modulation and direct detection (IM-DD) optical interconnects. While the equalizer implemented in the receiver's digital signal processing procedure can mitigate ISI, it also inevitably enhances the noise located in the decayed frequency region, known as equalization-enhanced colored noise (EECN). Additionally, the nonlinear impairments of the modulator and photodetector also deteriorate the performance of the IM-DD system, especially for high-order modulation formats. In this work, we propose a gradient-descent noise whitening (GD-NW) algorithm to address EECN and extend it by introducing nonlinear kernels to simultaneously mitigate EECN and nonlinear impairments. The proposed algorithms are compared with conventional counterparts in terms of the achievable baud rate and the receiver optical power sensitivity. As a proof-of-concept experiment, we validate the principles of the proposed algorithms by successfully transmitting 360-GBd on-off-keying (OOK) and 180-GBd 4-level pulse-amplitude-modulation (PAM-4) signals in the back-to-back case under a 62-GHz brick-wall bandwidth limitation. 280-GBd OOK and 150-GBd PAM-4 transmissions are also demonstrated over 1-km standard single-mode fiber with a bit error rate below 7% hard-decision forward error correction aided by the proposed approach.

Analyzing Peak-to-Average Power Ratio Characteristics in Multi-Channel Intensity Modulation and Direct Detection Flexible Transceivers Deploying Inverse Fast Fourier Transform/Fast Fourier Transform-Based Processing.

Cascaded inverse fast Fourier transform/fast Fourier transform (IFFT/FFT)-based multi-channel aggregation/de-aggregation offers a promising solution in constructing highly desirable flexible optical transceivers for considerably improving optical networks' elasticity, flexibility, and adaptability. However, the multi-channel aggregation operation unavoidably results in generated signals having high peak-to-average power ratios (PAPRs). To solve this technical challenge, this paper first explores the PAPR characteristics of the corresponding flexible transceivers in optical back-to-back (B2B) and 20 km intensity modulation and direct detection (IMDD) transmission systems, and then numerically investigates the feasibility and effectiveness of utilizing the conventional clipping techniques in reducing their PAPR reductions. The results show that the last IFFT operation size is the primary factor determining the PAPRs rather than the channel count and modulation format. For a given last IFFT operation size, the optimal clipping ratio can be identified, which is independent of channel count. With the identified optimal clipping ratio, when the channel count is >4, every two-channel increase in the channel count can only lead to <1.2 Gb/s decreases in the maximum aggregated signal transmission capacity.

Look-Up-Table-Based Direct-Detection-Faster-Than-Nyquist-Algorithm-Enabled IM/DD Transmission with Severe Bandwidth Limitation

The emergence of new applications is driving a dramatic growth in the capacity of data center interconnects. Intensity modulation and direct detection (IM/DD) has the characteristics of low cost, low power consumption and a small footprint. Industry and academia have conducted much research on IM/DD systems as a cost-effective solution. However, optical/electronic bandwidth and fiber dispersion are the restricting factors for the improvement of transmission capacity. Pattern-dependent distortion is an important aspect that affects system performance. In this paper, we propose a look-up table (LUT)-based direct-detection-faster-than-Nyquist (DDFTN) algorithm to compensate for pattern-dependent distortion. The performances of feedforward-equalization (FFE) only, the original DDFTN, least-squares (LS)-based DDFTN, and LUT-based DDFTN algorithms in IM/DD-based 112/140 Gbit/s four-level pulse-amplitude modulation (PAM-4) signal transmission were evaluated. The experimental results indicate that LUT-based DDFTN performs better with low computational complexity.

Adaptive decision threshold for an optical multipath-interference-impaired short-reach 50-Gbps PAM4 transmission.

The short-reach optical transmission systems based on intensity modulation and direct detection (IM/DD) are gradually evolving into the networks with complex link topologies and connections, especially inside the data center. Multipath interference (MPI) introduces irregular fluctuations in the 4-level pulse amplitude modulation (PAM4) signals and therefore affects the transmission performance. This Letter proposes an adaptive decision threshold (ADT) scheme to dynamically update the decision threshold, which can track the signal fluctuations in real time and mitigate the impact of MPI noise on the transmitted PAM4 signals. Numerical simulation results present that the proposed ADT scheme can significantly improve the bit error rate (BER) performance of the MPI-impaired PAM4 transmission system considering different MPI levels and laser linewidths. In a 50-Gbps PAM4 transmission system, the ADT can improve the MPI tolerance by more than beyond 6 dB when the BER reaches the KP4-forward error correction (FEC) criterion (2.4 × 10-4), presenting a better denoising performance than the existing MPI-mitigation algorithms A1 and A2. Moreover, the ADT scheme offers a lower computation complexity compared with A1 and A2, making it more practical for implementation.

A Simplified Volterra Equalizer Based on System Characteristics for Direct Modulation Laser (DML)-Based Intensity Modulation and Direct Detection (IM/DD) Transmission Systems

The nonlinear Volterra equalizer has been proved to be able to solve the problem of nonlinear distortion, but it has high computational complexity and is difficult to implement. In this paper, a simplified second-order Volterra nonlinear equalizer designed for intensity modulation/direct detection systems based on direct modulated laser is proposed and demonstrated, taking into account the characteristics of the system. It has been proved that the received signal of direct modulation laser/direct detection system can be expressed in Volterra series form, but its form is too complex, and the device parameters should also be considered. We re-derived it and obtained a more concise form. At the same time, we proposed a method to simplify the second-order Volterra nonlinear equalizer without relying on device parameters. The performance of the proposed Volterra nonlinear equalizer is evaluated experimentally on a 56 Gb/s 4-ary pulse amplitude modulation link implemented by using a 1.55 µm direct modulation laser. The results show that, compared with the traditional Volterra nonlinear equalizer, the receiver sensitivity of the equalizer is only reduced by 0.2 dB at most, but the complexity can be reduced by 50%; compared with diagonally pruned Volterra nonlinear equalizers, the complexity of the equalizer is the same, but the reception sensitivity can be improved by 0.5 dB.

Research on full duplex FSO access system with hybrid 16PSK/256QAM-OFDM downlink and duobinary uplink signals

a 100Gbit/s novel full duplex free space optical (FSO) access system scheme is proposed and demonstrated. Using the downlink hybrid 16phase shift keying (PSK)/256quadrature amplitude modulation (QAM)-orthogonal frequency division multiplexing (OFDM) and duobinary uplink signals. In downlink branch, in-phase/quadrature-phase (I/Q) modulation based on Mach-Zehnder modulator (MZM) and coherent detection technology are adopted. Meanwhile, 0.1Terahertz (THz) wave signal generated by two independent optical sidebands beating frequency at positive intrinsic-negative photodiodes (PIN PDs) for hybrid downlink 16PSK/256QM-OFDM signals. In uplink branch, intensity modulation and direct detection (IM/DD) can achieve reduced the communication budget cost and simplified the system configuration Simulation results show that the value of bit error ratio (BER) less than hardware decision forward error correction (HD-FEC) threshold after 300 m FSO channel transmission under the different weather conditions (such as sunny, rainy and snow).

Low-complexity clustered polynomial nonlinear filter-based electrical dispersion pre-compensation scheme in IM/DD transmission systems.

A polynomial nonlinear filter (PNLF)-based electrical dispersion pre-compensation (pre-EDC) scheme assisted with Gerchberg-Saxton (GS) algorithm is proposed to compensate the chromatic dispersion (CD) for intensity-modulation and direct-detection (IM/DD) optical transmission systems, where PNLF is utilized to fit the nonlinear transfer function of the iterative GS algorithm-based pre-EDC scheme to realize a low-complexity non-iterative CD pre-compensation. The capability of PNLF to fit the nonlinear iterative process enables the PNLF-based pre-EDC scheme to compensate for CD-induced linear distortions and address CD-induced nonlinear distortions, which are typically captured through iterative approaches. Additionally, to further reduce the computational complexity, we also introduce the k-means clustering algorithm to eliminate the weight redundancy and propose a lower-complexity clustered PNLF-based pre-EDC scheme. Simulation results show that PNLF-based and clustered PNLF-based pre-EDC schemes save 76.0% and 97.5% complexity with only 0.3 dB receiver sensitivity penalty at 20% forward error correction (FEC) threshold, compared with GS-based pre-EDC scheme in C-band 56 GBaud 80-km on-off keying (OOK) system. Furthermore, the effectiveness of PNLF-based and clustered PNLF-based pre-EDC schemes is also evaluated through the experimental demonstration. Experimental results show that under C-band 32 GBaud 80-km OOK system, bit error ratio (BER) satisfying 20% FEC threshold is achieved by applying PNLF-based and clustered PNLF-based pre-EDC schemes, which save 78.3% and 94.2% complexity with only 0.4 dB receiver sensitivity penalty compared with GS-based pre-EDC scheme, respectively. The research results indicate that the (clustered) PNLF-based pre-EDC scheme has the great application potential for CD compensation in high-performance and low-cost IM/DD optical transmission systems.

FPGA implementation for 44.2368-Gbit/s PAM8 signal transmission with pruned pre-equalization.

In this experiment, we demonstrated an intensity modulation and direct-detection (IM/DD) system based on a field-programmable gate array (FPGA). The PAM8 signals are successfully delivered at 44.2368 Gbit/s over a 45-km standard single-mode fiber (SSMF), satisfying the soft-decision forward error correction (SD-FEC) criterion of 2.4 × 10-2, and the net bit rate may reach 36.864 Gbit/s without the need of optical amplifiers. At the transmitter, we used a pruned pre-equalization algorithm to process the PAM8 signals, and the high-speed parallel PAM8 signals were processed at the receiver using 64 parallel constant modulus algorithm (CMA) and decision-directed least mean square (DD-LMS) equalizers. Additionally, we analyzed the bit error rate (BER) performance of the DD-LMS equalizer in FPGA simulation with various data lengths, both before and after equalization.

Probabilistic Shaping for High-Speed Unamplified IM/DD Systems With an O-Band EML

Probabilistic constellation shaping has been used in long-haul optically amplified coherent systems for its capability to approach the Shannon limit and realize fine rate granularity. The availability of high-bandwidth optical-electronic components and the previously mentioned advantages have invigorated researchers to explore probabilistic shaping (PS) in intensity-modulation and direct-detection (IM/DD) systems. This article presents an extensive comparison of uniform 8-ary pulse amplitude modulation (PAM) with PS PAM-8 using cap and cup Maxwell-Boltzmann (MB) distributions as well as MB distributions of different Gaussian orders. We report that in the presence of linear equalization, PS-PAM-8 outperforms uniform PAM-8 in terms of bit error ratio, achievable information rate and operational net bit rate indicating that cap-shaped PS-PAM-8 shows high tolerance against nonlinearities. In this paper, we have focused our investigations on O-band electro-absorption modulated laser unamplified IM/DD systems, which are operated close to the zero dispersion wavelength.

Perspectives on and the road towards 100 Gb/s TDM PON with intensity-modulation and direct-detection

We assess the status of current generation 25G and 50G time division multiplexed passive optical network (TDM PON) technologies based on leveraging the cost efficiencies of the Ethernet intra-datacenter ecosystem. As a first step towards 100G TDM PON, we predict the real-world impact of a flexible modulation enhancement to 50G PON, whereby four-level pulse amplitude modulation (PAM4) symbols can be transmitted at the same symbol rate as 50 Gb/s PAM2, but only where excess margins permit. We find that sufficient margins are likely to exist to allow for a majority of future 50G PON optical network units to operate at 100 Gb/s PAM4. Next, we look at the options for a 100G PON capable of supporting the full loss budget and reach requirements. There is no technical risk if coherent technology is adopted, but intensity-modulation and direct-detection (IM-DD) will provide lower complexity, lower cost, and lower power dissipation. We evaluate this option and conclude that by following IM-DD Ethernet optics to 100 GBd, single wavelength IM-DD will continue to be feasible for 100G PON and will be a strong contender for the next generation of PON after 50 Gb/s.

Suppressed Noise Enhancement Equalization Combined With Nonlinear-MLSE Techniques for Bandwidth-Limitation IM/DD System

Bandwidth limitation introduced inter-symbol interference (ISI) is the major impediment for high baud rate intensity modulation and direct detection (IM/DD) system with commercial devices. Least mean square (LMS) criterion based feedforward equalizer (FFE) is the most common method to eliminate ISI in single-carrier system. However, there is a tradeoff between the residual ISI and enhanced noise when the system bandwidth is severely limited. Although a post filter (PF) followed by maximum likelihood sequence estimation (MLSE) can suppress the enhanced noise effectively, the residual ISI left by post-FFE will degrade the system performance as the subsequent MLSE only handles ISI introduced by PF. In this paper, an adaptive partial response equalization realized by a channel-shortening filter (CSF) is investigated, which is combined with MLSE. As the target of CSF is a partial response signal with desired low-pass feature, the noise will not be enhanced in this scheme. And the residual ISI with determined response can be fully solved by MLSE. The performance of CSF based MLSE (CSF-MLSE) is evaluated and compared to PF based MLSE (PF-MLSE) in 60/70/75Gbaud four-level pulse amplitude modulation (PAM-4) system with 10-dB bandwidth of 16.2GHz. The experimental results show that CSF-MLSE has a better capability of ISI elimination compared to PF-MLSE. The bit error rate (BER) can be reduced from 7.4×10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> to 4×10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> and from 3×10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-2</sup> to 1×10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-2</sup> for 70Gbaud and 75Gbaud in optical back-to-back (OBTB) transmission. To further compensate the system nonlinear impairments, several nonlinear MLSE (NL-MLSE) techniques assisted by look-up table (LUT) or Volterra filter are proposed and investigated in this paper. The BER of 75Gbuad PAM-4 can be below 3×10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> after using NL-MLSE schemes.

Adaptive Hybrid Iterative Linearization Algorithms for IM/DD Optical Transmission Systems

For optical field recovery and linear dispersion compensation, we propose a performance-enhanced linearization algorithm, termed adaptive hybrid multi-constraint iteration algorithm (MCIA), which does not require any physical modifications to standard configurations of intensity-modulation and direct-detection (IM/DD) transmission systems. To improve the sensitivity to the residual inter-symbol interference (ISI) effect, we introduce, after fiber backward-propagation, a linear feed-forward equalizer (FFE) pair into the proposed algorithm. To improve the sensitivity to fiber dispersion estimation errors, we utilize a two-stage dispersion estimator coupled with the G-S iteration. After 100-Gb/s PAM-4 signal transmissions over 400-km fibers, the simulation results show that the MCIA offers a 1.5-dB optical signal-to-noise ratio (OSNR) gain and a 1-dB optical power budget improvement compared with the decision-directed data-aided iterative algorithm (DD-DIA), for highly dispersive IM/DD transmissions. By performing adaptive dispersion estimation, the MCIA has higher tolerance to estimation errors in fiber length. Moreover, for cases subject to large dispersion, the usage of the embedded FFE pair not only desensitizes the MCIA on the limited bandwidth effect, but also accelerates the convergence performance for reaching lower BERs. We experimentally demonstrate that the proposed algorithm can support 150-Gb/s PAM-4 transmissions over 25-km standard single mode fibers (SSMF), where just a 7-tap FFE-pair is required. For 150 Gb/s transmissions, the tolerance to fiber length estimation error is increased from 0.9 km to 20 km.

Optical OFDM waveform construction by combining complex symbols’ component of IFFT

In optical communication systems, orthogonal frequency division multiplexing (OFDM) is widely used to combat inter-symbol interference (ISI) caused by multipath propagation. Optical systems which use intensity modulation and direct detection (IM/DD) can only transmit real valued symbols, but the inverse discrete Fourier transform (IDFT) or its computationally efficient form inverse-fast Fourier transform (IFFT) required for the OFDM waveform construction produces complex values. Hermitian symmetry is often used to obtain real valued symbols. For this purpose, some trigonometric transformations such as discrete cosine transform (DCT) are also used; however, these transformations can eliminate the ISI only under certain conditions. In this paper, we propose a completely different method for the construction of OFDM waveform with IFFT to obtain real valued symbols by combining the real and imaginary parts (CRIP) of IFFT output electrically (E-CRIP) or optically (O-CRIP). Analytical analysis and simulation works are presented to show that compared to the Hermitian symmetric system, the proposed method slightly increases the spectral efficiency, eliminates ISI, significantly reduces the amount of needed calculation, and does not affect the error performance. In addition, the O-CRIP method is less affected by clipping noise that may occur due to the imperfections of the transmitter front-ends.

Enhanced Performance of Artificial-Neural-Network-Based Equalization for Short-Haul Fiber-Optic Communications

This work proposes an efficient and easy-to-implement single-layer artificial neural network (ANN)-based equalizer with improved compensation performance. The proposed equalizer is used for effectively mitigating the distortions induced in the short-haul fiber-optic communication systems based on intensity modulation and direct detection (IMDD). The compensation performance of the ANN equalizer is significantly improved, exploiting an introduced advanced training scheme. The efficiency and robustness of the proposed ANN equalizer are illustrated through 10- and 28-Gbaud short-reach optical-fiber communication systems. Compared to the efficient but computationally expensive maximum likelihood sequence estimator (MLSE), the proposed ANN equalizer not only significantly reduces its computational equalization cost and storage memory requirements, but it also outperforms its bit error rate performance.

Secure key distribution based on the polarization reciprocity of fiber and a coherent reception architecture.

Secure key distribution (SKD) schemes based on the interaction between a broadband chaotic source and the reciprocity of a fiber channel exhibit reliable security and a high key generation rate (KGR). However, under the intensity modulation and direct detection (IM/DD) architecture, these SKD schemes cannot achieve a long distribution distance due to the limitations on the signal-to-noise ratio (SNR) and the receiver's sensitivity. Here, based on the advantage of the high sensitivity of coherent reception, we design a coherent-SKD structure where orthogonal polarization states are locally modulated by a broadband chaotic signal and the single-frequency local oscillator (LO) light is transmitted bidirectionally in the optical fiber. The proposed structure not only utilizes the polarization reciprocity of optical fiber but also largely eliminates the non-reciprocity factor, which can effectively extend the distribution distance. The experiment realized an error-free SKD with a transmission distance of 50 km and a KGR of 1.85 Gbit/s.

Adaptive bias layered optical OFDM based on precoding for IM/DD systems

An adaptive bias layered optical orthogonal frequency division multiplexing (ABLO-OFDM) scheme based on real-valued precoding is proposed in the intensity modulation and direct detection (IM/DD) system. In ABLO-OFDM scheme, multilayer subcarriers are used to transmit data, which can achieve high spectral efficiency (SE) and reduce the peak average power ratio (PAPR). Compared with layered asymmetrically clipped O-OFDM (LACO-OFDM) scheme, only one inverse Fast Fourier transform (IFFT) block is needed in ABLO-OFDM. At the same time, the signal can be demodulated directly using the standard OFDM receiver. In addition, to resist the selective fading effect of the system, low-complexity real-valued precoding, namely discrete cosine transform (DCT) and discrete Hartley transform (DHT), are used to effectively balance the signal-to-noise ratio (SNR) between subcarriers and further reduce the PAPR. The result shows that the PAPR of the ABLO-OFDM system is reduced by 2.7 dB after adaptive bias layering, and the PAPR is further reduced by 2.4 dB at most after precoding. For the layered ABLO-OFDM system with DCT precoding, as the number of subcarrier layers decreases from L = 8 to L = 1, the required receiver optical power (ROP) is reduced by 6 dB. It proves that the ABLO-OFDM system with DCT precoding can achieve higher SE and effectively improve receiver sensitivity.

Non‐linear modelling and distortion compensation in optical Fast‐orthogonal frequency division multiplexing systems

AbstractFast‐OFDM‐based intensity‐modulation and direct‐detection (IM/DD) has been proposed for deployment of cost‐efficient optical access networks, due to its implementation simplicity and high spectral efficiency. In this article, the accuracy of the generalised memory polynomial (GMP) for the non‐linear modelling of optical Fast‐OFDM links is studied, including memory effects and considering different model parameters. After model validation using measured data of a 10 km single mode fibre link, the GMP is used for performance investigations of a distortion compensation approach to optical Fast‐OFDM, for up to 16PAM modulation formats and different number of Fast‐OFDM subcarriers. This study firstly reports the performance results of optical 16PAM‐Fast‐OFDM systems using either 2PAM‐ or 4PAM‐based training signals for digital post‐distortion and FFT‐based channel estimation, and firstly investigates the influence of the zero padding (ZP) length on the performance of optical Fast‐OFDM. Excellent performance improvements are achieved using the proposed distortion compensation scheme, relative to conventional system implementation.

Characterization of Nonlinear Distortion in Intensity Modulation and Direct Detection Systems

Intensity modulation and direct detection (IM-DD) systems are widely used in short-reach optical networks. Thus, developing a practical and accurate method to characterize nonlinear distortion and to estimate system performance is essential, as this is the foundation of IM-DD system design. The amount of nonlinear distortion can be characterized using the noise-to-power ratio (NPR). Although measuring the NPR using a notch requires only a spectrum analyzer, this method cannot be applied to a nonlinear system with non-Gaussian stimuli in general. We employ the method of measuring the NPR using a notch to characterize the nonlinear distortion in directly modulated distributed feedback (DM-DFB) laser-based IM-DD systems. Nonlinear distortion in these IM-DD systems can be attributed to two specific mechanisms: the imperfect power–current characteristic of the DM-DFB laser and the interaction among the modulation, chromatic dispersion (CD), and detection. Experimental results demonstrated that the nonlinear distortion can be accurately characterized with a mean absolute error of 0.47 dB, even when the stimuli are pulse amplitude modulation. The system performance subjected to nonlinearity could be estimated by the equivalent additive noise model. Besides, the method of measuring the NPR using a notch is also effective when the Mach–Zehnder modulator-based IM-DD system has nonnegligible CD. However, it failed in the case of negligible CD. Considering that this method is not always effective, we analyzed the attributes of various nonlinear systems and found that the above method is applicable only to systems dominated by second-order nonlinearity.

Comparison of post-equalizers for beyond 100-Gb/s/[formula omitted] C-band signal transmission over a 100-km dispersion-uncompensated SSMF

A comprehensive comparison among different post-equalizers with relatively low complexity is studied for C-band 100-km dispersion-uncompensated standard single-mode fiber (SSMF) intensity modulation and direct detection (IM/DD) transmission systems with data rate beyond 100 Gb/s/λ. These representative post-equalizers include feed-forward equalizer (FFE), polynomial-based nonlinear FFE (P-NFFE), absolute-term based nonlinear FFE (AT-NFFE), FFE combined with decision-feedback equalizer (FFE-DFE), polynomial based nonlinear FFE-DFE (P-NLE), absolute-term based nonlinear FFE-DFE (AT-NLE), and their lower-complexity versions of FFE-DFE-WS, P-NLE-WS, and AT-NLE-WS which use weight sharing (WS) to eliminate weight redundancy. We demonstrate 100-Gb/s/λ and 112-Gb/s/λ on-off keying (OOK) transmissions over a 100-km SSMF. For 112-Gb/s transmission, BERs of FFE-DFE(-WS), P-NLE(-WS), and AT-NLE(-WS) can reach 7% hard-decision forward error correction (HD-FEC) limit at 3.8 × 10−3. Under 7% HD-FEC limit, AT-NLE-WS with 32 real-valued multiplications shows similar BER performance as P-NLE and AT-NLE with a small power penalty of < 0.4 dB, but outperforms P-NLE-WS, AT-NLE, and P-NLE in huge complexity reduction of approximately 83.2%, 92.4%, and 92.7%, respectively. Therefore, taking both the BER performance and the operation complexity into account, AT-NLE-WS is the optimal equalizer and is a strong candidate to be applied in low-cost C-band IM/DD interconnections with data rates beyond 100 Gb/s/λ and transmission distance up to 100 km.

Five-LP-Mode IM/DD MDM Transmission Based on Degenerate-Mode-Selective Couplers With Side-Polishing Processing

Weakly-coupled mode division multiplexing (MDM) techniques supporting intensity modulation and direct detection (IM/DD) have attracted great attention for capacity enhancement of short-reach applications such as optical interconnections, for which mode multiplexers/demultiplexers (MMUX/MDEMUX) with low insertion loss (IL) and modal crosstalk are the key components. In this paper, we firstly propose the design method for degenerate–mode-selective couplers (DMSC) with side-polishing processing. Three kinds of DMSCs for different degenerate linearly-polarized (LP) modes (LP <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">11</sub> , LP <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">21</sub> and LP <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">31</sub> ) in a weakly-coupled few-mode fiber (FMF) are designed. Then a pair of MMUX and MDEMUX consisting of cascaded mode-selective couplers (MSC) and DMSCs for all the 5 LP modes of the FMF are fabricated with side-polishing processing. The measurement results show that the MMUX and MDEMUX achieve low back-to-back IL lower than 5.3 dB for all the 5 modes. Finally, stable digital-signal-processing (DSP)-free 5-mode IM/DD MDM transmission utilizing conventional optical modules over 10-km FMF are successfully demonstrated. The proposed low-IL MMUX/MDEMUX is scalable to support more modes and can promote the practical application of MDM techniques.