Influence Of Different Levels Research Articles

Effects of risk information on pedestrian evacuation during fire emergencies: Virtual experiments and survey

In fire emergencies, pedestrians often face uncertainty about the safety of evacuation routes due to a lack of risk information, which makes the emergency evacuation highly challenging. Although risk information is crucial for effective evacuation, the effect of varying levels of risk information on fire evacuation remains insufficiently explored. This study aims to address this gap by investigating the influence of different levels of risk information on pedestrian evacuation through virtual experiments and survey. We conducted a series of multiplayer fire evacuation experiments in Minecraft. The risk information provided to pedestrians before evacuation was controlled at three levels: no risk information, partial risk information, and complete risk information, by giving different risk information cues. The results of experiments indicated that risk information can improve pedestrian evacuation efficiency during fire emergencies, while more complete risk information can further improve pedestrian evacuation efficiency. Additionally, an information transfer phenomenon was observed during fire evacuations, in which pedestrians adjusted their behaviour based on perceived fire, leading others to avoid the fire in advance. The analysis of pedestrian behaviour revealed that pedestrians did not exhibit imitative behaviour in evacuation direction choices during fire emergencies. Pedestrian route choices were significantly influenced by the initial distance of pedestrians relative to the exits. Moreover, complete risk information cues did not significantly influence pedestrians’ route choices compared with partial risk information cues. A post-experimental survey was conducted to assess pedestrians’ route choice preferences under different risk information cue scenarios. The results showed that pedestrians preferred the nearest route.

Effect of IBA Concentration (Indol Butaric Acid) and Growing Condition on Performance of Cuttings in Mogra (Jasminum sambac)

An experiment was laid out to study influence of different levels of IBA and growing condition on cuttings of Mogra (Jasminum sambac) at Sheth D. M. polytechnic in Horticulture College, Anand Agricultural University, Model farm, Vadodara during 2022 to 2024. The study was conducted using completely randomized design with factorial concept and three replications for each treatment. Total 10 treatment combination of two factors viz., growing condition (open and NVPH) and IBA concentration (500, 1000, 1500 and 2000 ppm) were compared with control (deepen in distilled water). IBA significantly improved the performance of cuttings under naturally ventilated poly-house condition. 1500 ppm IBA concentration recorded significantly lower days to sprout (13.83 days), higher shoot length at 30, 45 and 60 DAP (2.80 cm, 7.64 cm and 11.63 cm), root length (4.18 cm), number of leaves at 30, 45 and 60 DAP (2.87, 6.03 and 8.47), fresh weight (11.63g), dry weight (4.18g) and survival percentage (66.11%). Where as in growing condition, naturally ventilated poly-house recorded significantly lower days to sprout (13.27 days), higher shoot length at 30, 45 and 60 DAP (2.40cm, 7.26 cm and 11.80 cm), root length (3.89 cm), number of leaves at 30, 45 and 60 DAP (2.72 , 4.80 and 7.85), fresh weight (11.80 g), dry weight (3.89 g) and survival percentage (64.56%). Semi hardwood cuttings of Jasminum sambac treated with 1500 ppm IBA concentration treatment for 5 min and planted in polybags under Naturally ventilated poly-house showed promising growth with higher sprouting and survival percentage as compared to other treatments. It was recommended to propagate semi hardwood cuttings of Jasminum sambac with 1500 ppm IBA concentration for 5 min and plant them in naturally ventilated polyhouse to get maximum sprouting percentage and quality planting material.

Health Locus of Control and Medical Behavioral Interventions: Systematic Review and Recommendations.

Health locus of control (HLOC) is a theory that describes how individuals perceive different forces that influence their lives. The concept of a locus of control can affect an individual's likelihood to commit to behaviors related to their health. This study explores the literature on the relationships between HLOC and medical behavioral interventions. This study aims to better understand how HLOC constructs can potentially affect patient responses to health behavioral interventions and to propose a series of guidelines for individuals interested in designing medical behavioral interventions related to HLOC. We used the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) methodology and performed an analysis of 50 papers related to the topic of HLOC and medical behavioral interventions. Inclusion criteria were studies that had a behavioral intervention involving patients and contained a metric of at least 1 of the constructs related to HLOC. The initial screening and search were conducted by 2 researchers (AY and SM) separately. The results were then combined and compared. Our findings explore the influence of different levels of HLOC along with the importance of both patient- and health-related context when assessing the relationships between HLOC constructs and the likelihood of health behavior change. The findings show that different constructs related to HLOC can act as reliable predictors for patient responses to medical behavioral interventions. Patients who score higher on internal HLOC measures are more likely to exhibit behaviors that are consistent with positive health outcomes. Patients who score higher on chance HLOC are more likely to exhibit behaviors that may lead to adverse health outcomes. These conclusions are supported by most of the 50 studies surveyed. We propose guidelines for individuals designing medical behavioral interventions so that they can make use of these relationships linked to HLOC. The three guidelines suggested are as follows: (1) in most situations, improving internal HLOC will improve health outcomes for patients; (2) patients with high external HLOC should be further studied to determine the source of the external HLOC; and (3) patients with a high chance HLOC are less likely to follow preventative behaviors or be responsive to interventions. Limitations of the study are that the primary search and analysis were conducted by 2 principal researchers (AY and SM). Interpretation and development of the guidelines are subject to individual interpretation of results and may not be applicable to all contexts.

Influence of different levels of black soldier fly larvae meal on growth performance and carcass quality of broiler chickens

A study was conducted to examine the impact of two inclusion levels of Black soldier fly larvae meal (BSFLM) replacing soybean meal on growth performance, nutrient utilization, carcass characteristics and meat quality of broilers. Three experimental diets based on corn-soybean meal were developed to contain 0 (control), 6 (BSF 6) and 12% (BSF 12) BSFLMfor both starter and grower phases. Each experimental diet was randomly allotted to six replicate pens (eight birds per pen). The birds were offered starter pellets from 0 to 14 day post-hatch and grower pellets from 15 to 28 day post-hatch. The experimental diets were tested for pellet durability index (PDI). There was an interaction between diet and growth phase (P < 0.001) for pellet durability index where starter diets had always a higher PDI than the grower diets, but the difference was greater for control diet than BSF 6 and BSF 12 diets. Apparent metabolizable energy (AME) of diets and coefficients of apparent ileal digestibility (CAID) of nutrients were measured on day 28 using titanium dioxide marker ratios in the diet and excreta/ileal digesta. On day 28, the weights of live body, carcass, fat pad, breast and gizzard were recorded, and then breast meat quality (meat pH, drip loss and cooking loss) was examined. Inclusion of BSFLM of up to 12% did not reduce live weight gain or feed intake. Live weight and carcass weight were heavier in broilers fed 12% BSFLM than controls (P < 0.02), but were not different than those fed 6%, while controls were not different than those fed 6%. Breast weight (percentage live weight) was lower in birds offered 12% BSFL than in others (P < 0.04). No differences were observed between diets for the percentage weight as carcass, fat, pad and gizzard. The AME and AMEc of diets were the highest in broilers fed 6% BSFLM diet (P < 0.005), but there were no differences between controls and those fed 12% BSFLM. The CAID of DM, ash and N in birds fed 6% BSFLM were greater than (P < 0.03) birds fed 12%, but were not different than controls, which were also not different than those fed 12%. Broiler breast meat quality was unaffected by dietary treatments. In conclusion, BSFLM at 12% can be used effectively as a SBM replacement in starter and grower diets, without affecting the growth performance, nutrient utilization, carcass characteristics and meat quality of broiler chickens.

Percolation Statistics in the MillenniumTNG Simulations

The statistical analysis of cosmic large-scale structure is most often based on simple two-point summary statistics, like the power spectrum or the two-point correlation function of a sample of galaxies or other types of tracers. In contrast, topological measures of clustering are also sensitive to higher-order correlations and thus offer the prospect to access additional information that may harbor important constraining power. We here revisit one such geometric measure of the cosmic web in the form of the so-called percolation analysis, using the recent MillenniumTNG simulation suite of the ΛCDM paradigm. We analyze continuum percolation statistics both for high-resolution dark matter particle distributions and for galaxy mock catalogs from a semianalytic galaxy formation model within a periodic simulation volume of 3000 Mpc on a side. For comparison, we also investigate the percolation statistics of random particle sets and neutrino distributions with two different summed particle masses. We find that the percolation statistics of the dark matter distribution evolves strongly with redshift and thus clustering strength, yielding a progressively lower percolation threshold toward later times. However, there is a sizable residual dependence on numerical resolution, which we interpret as a residual influence of different levels of shot noise. This is corroborated by our analysis of galaxy mock catalogs, whose results depend on sampling density more strongly than on galaxy selection criteria. While this limits the discriminative power of percolation statistics, our results suggest that it still remains useful as a complementary cosmological test when controlled for sampling density.

Agricultural knowledge and youth participation in agriculture and agribusiness in an African context

ABSTRACT This study examines youths’ decision to participate in agriculture and agribusiness from an agricultural knowledge lens. Data collected from 520 respondents across Ghana were analysed descriptively and inferentially. The results show the influence of different levels of science-based (objective) agricultural knowledge on youths’ participation in agriculture and agribusiness, in addition to subject knowledge. Similarly, the findings reveal that gender, having family and friends engaged in agriculture, and participating in capacity-building training influence youths’ participation in agriculture and agribusiness. Agricultural experience, age, and education significantly shape objective agricultural knowledge. The policy implications of these findings are discussed and strategies for promoting the acquisition of objective knowledge and scaling up youths’ participation in agriculture and agribusiness are provided.

Metal artifact reduction tool and mA levels impact on the diagnosis of fracture extension in endodontically treated teeth using cone-beam CT.

To evaluate the influence of different levels of metal artifact reduction (MAR) tool and milliamperage (mA) on the diagnosis of fracture extension in endodontically treated teeth using cone beam CT (CBCT). Ten maxillary premolars were endodontically treated and positioned in the empty sockets of a human maxilla covered with wax. CBCT acquisitions were performed using the Eagle Edge device (Dabi Atlante, Brazil) adjusted to 120 kVp, FOV of 4 × 6cm, exposure time of 24s and voxel size of 0.2mm in 8 different conditions with different MAR (1, 2 and 3) and mA (3.2 and 6.3) levels. Crown-root fractures were simulated in the universal testing machine, and CBCT images were acquired again. Five radiologists evaluated the presence and extension of fractures with a 5-point scale. Statistical analysis was performed by analysis of variance, Tukey and Kappa test (α = 0.05). Although different mA levels did not significantly (p > 0.05) affect the diagnosis values for fracture presence and extension, when evaluated the different levels of MAR, AUC and sensitivity showed significantly higher values (p < 0.05) for MAR 0 using 6.3mA and kappa agreement showed significantly higher values (p < 0.05) for MAR 0 and 2 using 6.3mA. Although mA levels do not have a diagnostic effect when isolating the MAR level; in 6.3mA, MAR 0 and 2 can positively influence the diagnosis of fracture extension in endodontically treated teeth using CBCT. The isolate evaluation of dental fracture presence can overlook diagnostics error of its extension.

Influence of Different Levels of Hydrogel on Root Nodulation in Chickpea (Cicer arietinum L.)

This study investigated the impact of varying levels of hydrogel on the root nodules of Chickpea (Cicer arietinum L.) during Rabi seasons of 2019-20 and 2021-22 at the Department of Biological Sciences, Sam Higginbottom Institute of Agriculture, Technology, and Sciences, (U.P). The experimental design was a randomized block design with four levels of hydrogel (25%, 50%, 75% and 100%) and two levels of irrigation (one irrigation and two irrigation) and all treatments replicated thrice. Observations on the number of nodules per plant, active nodules, and inactive nodules were recorded at 30, 60, and 90 days after sowing (DAS) and at maturity and analysed using Fisher's ANOVA. The results indicated that hydrogel application significantly affected nodule formation at all growth stages across both years. The highest number of nodules, active nodules, and inactive nodules were recorded in treatment T10 (2 irrigations + 100% hydrogel), followed by T9 (2 irrigations + 75% hydrogel), in both years. The enhanced nodule formation with hydrogel application was attributed to improved water availability to the roots during periods of water scarcity, highlighting hydrogel's role in optimizing nitrogen availability and promoting chickpea growth, which is crucial for enhancing soil fertility.

Mitigation of Photovoltaics Penetration Impact upon Networks Using Lithium-Ion Batteries

The paper conducts a comprehensive analysis of the impact of very large-scale photovoltaic generation systems on various aspects of power systems, including voltage profile, frequency, active power, and reactive power. It specifically investigates IEEE 9-bus, 39-bus, and 118-bus test systems, emphasizing the influence of different levels of photovoltaic penetration. Additionally, it explores the effectiveness of battery energy storage systems in enhancing system stability and transient response. The transition to PV generation alters system stability characteristics, impacting frequency response and requiring careful management of PV plant locations and interactions with synchronous generators to maintain system reliability. This study highlights how high penetration of photovoltaic systems can improve steady-state voltage levels but may lead to greater voltage dips in contingency scenarios. It also explores how battery energy storage system integration supports system stability, showing that a balance between battery energy storage system capacity and synchronous generation is essential to avoid instability. In scenarios integrating photovoltaic systems into the grid, voltage levels remained stable at 1 per unit and frequency was tightly controlled between 49.985 Hz and 50.015 Hz. The inclusion of battery energy storage systems further enhanced stability, with 25% and 50% battery energy storage system levels maintaining strong voltage and frequency due to robust grid support and sufficient synchronous generation. At 75% battery energy storage system, minor instabilities arose as asynchronous generation increased, while 100% battery energy storage system led to significant instability and oscillations due to minimal synchronous generation. These findings underline the importance of synchronous generation for grid reliability as battery energy storage system integration increases.

Investigation of the effect of relative humidity on micro lime consolidation of degraded earthen structures

Micro lime, hydrated lime (Ca (OH)2) with particle sizes of 1-3μ dispersed in isopropanol, can be used to reinforce deteriorated earthen structures. The consolidation effect depends on the amount of moisture present in the structure or in the ambient air. This study investigates the influence of different levels of relative humidity (RH) on the consolidation effect of micro lime on earthen structures, the chemical processes responsible for the consolidation and the physical changes to the structure. The aim is to gain a deeper understanding of the underlying chemical reactions and to identify a potential limit to the applicability of this consolidation method in low RH environments. The fact that many of these sites are located in arid climates greatly influences the practical application of micro lime in the conservation of historical earthen structures. To characterize the consolidation effect of micro lime, unconfined compressive strength and exposure to wet and dry cycles were used. The properties of the reaction products and the bonding between soil particles and micro lime were investigated using thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), mercury intrusion porosimetry (MIP) and scanning electron microscopy (SEM). At RH levels of 25%, 45%, 65% and 90%, the unconfined compressive strength (UCS) and the modulus of deformation at 50% strength (E50) of the micro lime-reinforced specimens demonstrated an increase with humidity. This led to a significant improvement in their ability to resist the effects of dry–wet cycles. Results from thermal gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) indicate that micro lime interacts with the soil matrix via carbonation, with the reaction rate increasing with humidity. At 25% RH, vaterite was produced and residual free lime was observed, whereas at humidity levels of 45% and above, the reaction yielded vaterite and aragonite. The lime treatment did not significantly alter the pore structure of the soil specimens. The total porosity of the specimens was only slightly reduced, with the main effect of the lime treatment being a reduction in the number of large pores.

Influence of different levels of N application and foliar spray of zinc on growth and economics of hybrid maize

Influence of different levels of N application and foliar spray of zinc on growth and economics of hybrid maize

Impact and accumulation of calcium on soft-shell mud crab Scylla paramamosain in recirculating aquaculture system

Soft-shell crabs are highly valued for their commercial significance and culinary appeal. To enhance production of soft-shell crabs, careful attention should be paid to the water calcium concentration in their culture. This study investigated the influences of different levels of calcium concentrations on the molting and growth of mud crab (Scylla paramamosain) within a meticulously controlled recirculating aquaculture system (RAS). We established three distinct water calcium concentration gradients (200, 300, and 450 mg/L) to comprehensively assess feeding habits, molting patterns, growth, and tissue calcium levels of mud crab. Initially, we observed a gradual reduction in water calcium concentrations with increments of crab molting events in RAS. Throughout one molting cycle, the feeding incidence of the crabs remained consistently high from 4 days to 37 days post-molt, irrespective of different calcium concentrations. Nonetheless, high water calcium levels (300 and 450 mg/L) significantly shortened molt intervals and accelerated exoskeletal calcification. Specifically, the molt intervals were 52.30 ± 2.72 d, 41.65 ± 5.24 d, and 37.70 ± 3.02 d, while the carapace hardening durations were 21.51 ± 4.33 h, 17.23 ± 3.38 h, and 13.46 ± 2.76 h at water calcium concentrations of 200, 300, and 450 mg/L, respectively. Moreover, elevated calcium concentrations also significantly enhanced weight gain of the mud crab during molting. Noteworthy, regardless of fluctuations in water calcium concentration, the condition factor of the molting crabs was approximately 63%, which could be an indicator of crab selection in soft-shell crab cultivation. Furthermore, the dynamic changes in calcium concentrations were disparate among different tissues in the post-molt stage. Gill and exoskeleton tissues exhibited an upward trend in calcium concentrations, while hemolymph and hepatopancreas tissues displayed distinct patterns of decrease followed by increase. Gill and exoskeleton tissues were identified as primary sites for calcium absorption and utilization, evidenced by a positive correlation between high calcium concentrations and increased calcium content in these tissues at 6 h and 3 d post-molt. Overall, our findings provide practical evidence for optimizing aquaculture management strategies through adjustments in water calcium concentration, thus to enhance production efficiency and profitability in soft-shell mud crab aquaculture.

Response of Inorganic Fertilizer and Plant Growth Regulators on Growth and Seed Yield of Radish (Raphanus sativus L.)

This study aimed to evaluate the influence of different levels of inorganic fertilizer and plant growth regulator on seed yield of radish (Raphanus sativus L.) was formulated and conducted during the rabi season of 2022-23 at vegetable seed production plot, Department of Horticulture (Vegetable &amp; Floriculture), BAC, Sabour Bhagalpur. The experiment was conducted to determine seed production ability at four levels of fertilizers viz, (F0-control, F1-N40:P30:K40, F2-N60:P40:K50,&amp; F3-N8P50:K50) as well as seven levels of PGRs viz, P0 (Control), P1 (GA3 @ 50ppm), P2 (GA3 @100 ppm), P3 (GA3 @ 150 ppm), P4 (NAA @ 50 ppm), P5 (NAA @ 100 ppm) and P6 (NAA @ 150 ppm). Inorganic fertilizers were applied at 20 days and PGRs as foliar spray at 30 and 60 days after stecklings transplanting. The experiment was conducted in RBD (Factorial) and replicated thrice. the combined effect of inorganic fertilizers and Plant growth regulators F2P3 significantly gave maximum diameter of pod (7.64 mm), length of pod (56.61mm), number of seeds/pod (6.18), 1000- seed weight (15.12g) and seed yield (18.23q/ha) and plant height is non significant. The treatment combination F3P6 gave the maximum number of branches (8.06). Hence, F2P3 treatment combination is a best combination for seed yield of radish and enhancing seed yield is our ultimate goal. As we performed the study in a particular location, we recommend multilocation trials in different agro-climatic regions to study and final confirmation of the results.

Influence of Different Level of NPK and Rhizobium on Physico Chemical Properties of Soil, Growth and Yield Attribute of Blackgram (Vigna mungo L.) Var: Shekhar-2

Influence of Different Level of NPK and Rhizobium on Physico Chemical Properties of Soil, Growth and Yield Attribute of Blackgram (Vigna mungo L.) Var: Shekhar-2

Influence of Higher Education E-Service Quality on E-Learning Student Satisfaction; As Moderated By Digital Literacy: A Mixed Method Research Approach

Introduction: This paper explores the impact of college e-service quality on student satisfaction in the context of the innovative practice of "Internet + Education" in order to research whether there is any difference in students' perception of college e-service quality under the influence of different levels of digital literacy. The research object of this paper is students of universities in Kunming, and the SERVQUAL model is extended. Among them, the independent variables are the five dimensions of e-service quality. The dependent variable is online education student satisfaction. The moderating variable is digital literacy. This research is based on relevant service theories. A combination of quantitative and qualitative methods is used. The results of the research show that the impact of service quality on college students' e-learning satisfaction is different under different levels of digital literacy. Objective: The research objective of this paper is to investigate the impact of the quality of e-services in higher education on student satisfaction in order to research whether there are differences in students' perceptions of the quality of e-services in higher education under the influence of different levels of digital literacy. Theoretical Framework: This research was expanded with the SERVQUAL model and followed the exploratory sequential mixed methods process of scientific investigation, from the initial selection of variables to the final discussion of recommendations and countermeasures. Method: In this study, the scientific survey process of exploratory sequential mixed methods was used to research the satisfaction of college students with online education based on the theory of digital literacy and service quality, using college students in Kunming, China, as the target of the survey, and a combination of quantitative and qualitative research methods. Results and Discussion: The results of the analysis showed that the independent variable: the five factors of e-services (the higher, the higher the satisfaction of students. And under the moderating variable, digital literacy moderated all the other factors, only the relationship between responsibility and e-learning student satisfaction had no significant moderating effect. [synthesize the main results of the research]. In the discussion section, these results will be correlated according to the theoretical framework, highlighting the identified effects and relationships. This section also considers possible limitations of the research. Research Implications: 1. theoretical significance: by constructing a comprehensive theoretical model, this research aims to provide new insights into the field of e-learning. It not only helps to understand the impact of E-learning platform design and service quality, but also emphasizes digital literacy as an important moderating variable. 2. Practical significance: The research results will provide value to educational technology developers and educational policy makers, helping them to optimize e-learning platforms to enhance user experience and learning outcomes. Originality/Value: This research expands the SERVQUAL model by taking online education as the background, combining the actual situation of online education in China, and taking digital literacy as the variable. It allows colleges and universities to break through the original traditional education model. And lifelong learning and personalized learning are the focus of the reform of continuing education in colleges and universities. The results of this research will promote colleges and universities to continuously improve the quality of online education and provide reference for schools and teachers to carry out online education and continuing education.

THERMOPHYSICAL PROPERTIES OF HYPOEUTECTIC, EUTECTIC AND HYPEREUTECTIC Al-Si AUTOMOTIVE ALLOYS UNDER AGEING TREATMENT

Influence of different levels of silicon under a variety of thermal treatment is investigated on the thermophysical behaviour of Al-Si-Cu-Mg automotive alloys. Conventional cast alloys are subjected to T6 heat treatment for age hardening. Hardness values, thermal conductivity along with microstructural observation under different heat-treated conditions are well thought-out to comprehend the ageing performance and the precipitation behaviour of the alloys. From these investigational results it is indicated that two successive hardening peaks take place in the agedalloys. Ageing sequence consists of different phases like a supersaturated solid solution, GP zones, intermediate βʹʹ, intermetallic βʹ, equilibrium β and the Q phase but GP zones and the metastable phases are most likely responsible for these ageing peaks. Thermal conductivity decreases for these precipitates formation during ageing and increases for relieving the internal stress, dissolution of metastable phase and coarsening the precipitation of the alloys. Addingup of Si to the alloy showed earlier ageing peaks with higher intensities intended for its increasing properties of heterogeneous nucleation and diffusion kinetics. After ageing around at 200°C for four hours the alloys offer the height hardness. Microstructural study reveals that eutectic silicon makes the grain boundary coarsen and beyond the eutectic composition the star-shaped blocky primary Si is formed. Subsequent to ageing at 350oC for one hour the alloys reach completely recrystallized state.

Influence of different level of sulphur and zinc on physico-chemical properties of soil yield attributes and nutrient content of maize (Zea mays L.) Shakti 8484

Influence of different level of sulphur and zinc on physico-chemical properties of soil yield attributes and nutrient content of maize (Zea mays L.) Shakti 8484

Feed costs and indicators of reproductive capacity of high-yielding cows at different levels of Bypass soybeans in rations

The article presents the results of a scientific and economic experiment to study the influence of different levels of Bypass soybeans in the diets of high-yielding cows on feed costs per kilogram of milk and reproductive functions of cows. Provision of the rations of the experimental cows with an unequal amount of the difficult-to-dissolve fraction of crude protein, at the expense of Bypass soybeans, affected their consumption of bulk feed. The experimental cows consumed 4.1–4.8 kg from the specified 5 kg of alfalfa hay, 20.8–24.6 kg from 25 kg of corn silage, and 8.4–9.7 kg from 10 kg of alfalfa hay. The consumed feed provided cows with crude protein at the level of 16.0–16.5 % of the dry matter, its poorly soluble fraction at the level of 27.3 % of the crude protein in the 1st control group, 31.1 % in the 2nd experimental group, 35.2 % – in the 3rd experimental group and 40.0 % – in the 4th experimental group. The sugar-starch-protein ratio was normal and ranged from 2.20 to 2.28 : 1 with a norm of 2.1 : 1. The micronutrient rations were balanced due to micronutrients of organic origin. On the basis of the obtained data, it was proved that the lowest feed consumption per 1 kg of milk was observed in cows of the 4th experimental group, which were fed rations with 2 kg of Bypass soybeans, where the level of insoluble protein was 40 % of crude protein and these consumptions were 6.5 MJ against 7.4 MJ in the 1st control group. Cows of the 4th experimental group also had the best insemination and service period indicators. The duration of the service period in the experimental groups was less in percentage compared to the animals of the 1st control group by: 15.0 in the 2nd; 25.6 in the 3rd and 32.9 in the 4th. Partial and complete replacement in the diets of cows of the 2nd, 3rd and 4th experimental groups of soybean meal with Vypass soybeans at the level of 1.0; 1.7 and 2 kg of compound feed concentrate in the first 100 days of lactation has a positive effect on the physiological state, stimulates appetite and provides normal conditions for fertilization and embryo development.

The Influence of Different Levels of Sodium Chloride, Sodium Nitrite, and Glucose on Biogenic Amines and Microbial Communities in Fermented Goat Meat Sausage.

The influence of different levels of sodium chloride, sodium nitrite, and glucose on the quality characteristics of spontaneously fermented goat meat sausage was investigated. The amounts of total biogenic amines in all the sausages ranged from 324.70 to 388.77 mg/kg; among them, spermine was the most abundant, with amounts ranging from 230.96 to 275.78 mg/kg. Increasing sodium chloride from 15 to 35 g/kg, the content of cadaverine, putrescine, tyramine, phenylethylamine, tryptamine, and total amines decreased, and Enterobacteriaceae counts decreased at the same time. Increasing sodium nitrite from 150 to 250 mg/kg, the content of cadaverine, histamine, and total amines decreased, while Enterobacteriaceae counts decreased simultaneously. Increasing glucose from 10 to 40 g/kg, the content of cadaverine, spermidine, and total amines decreased. Enterococcus was the most abundant genus across all the samples, and the relative abundance of Enterococcus was reduced obviously by increasing sodium nitrite and glucose levels. The top 10 differential bacterial taxa for each additive group were respectively obtained, and microbial biomarkers for each level of additive within its group were acquired, respectively. Through Pearson correlation, Lactobacillus was positively correlated with phenylethylamine, tryptamine, tyramine, and cadaverine, Bacteroides and Sediminibacterium were positively correlated with phenylethylamine and putrescine, respectively, suggesting they have the potential to produce biogenic amines. The results provided references for controlling the accumulation of biogenic amines in fermented goat meat sausage via the addition of auxiliary additives during the processing.

Ulnar osteotomy between the proximal 1/3 and 1/5 provides a stable radiocapitellar joint in chronic Monteggia fracture.

The precise location of unlar osteotomy remains a subject of ongoing controversy in chronic Monteggia fracture (CMF). The purpose of this study was to analyze the influence of different levels of ulnar osteotomy on redislocation in CMF. We retrospectively reviewed 18 children following our previous series. Except the baseline characteristics and radiographic parameters such as ulnar osteotomy angle, maximum interosseous distance (MID) and proportional ulnar length (PUL), we introduced a new parameter: proportional ulnar osteotomy (PUO) which represents the quantitative level of proximal ulnar osteotomy. Based on the value of PUO, we divided it into two intervals: appropriate PUO range (1/5< PUO <1/3) and inappropriate PUO range (PUO >1/3; PUO <1/5). The relationship between these indexes and redislocation was analyzed. According to the reduction state of radial head, patients were divided in two groups: reduced (15/18) and redislocation (3/18). Only PUO range differed significantly (P=0.043) between the two groups, with a notably higher number of patients showed an osteotomy between 1/5 and 1/3 of ulna in reduced group. Combining PUO range with radiographic parameters (osteotomy angle and post-PUL) improved the accuracy and specificity over using osteotomy angle and post-PUL (accuracy, 94.44% vs. 83.33%) (specificity, 93.33% vs. 86.67%, P=0.008). This combination further enhanced the predictive capability for detecting the risk of redislocation in CMFs. Ulnar osteotomy between the proximal 1/3 and 1/5 appears to provide a much safer and more stable radiocapitellar joint in CMF.