Industrial, Scientific And Medical Band Research Articles

Dual-band microstrip patch antenna for IoT application

Internet of Things (IoT) primarily based application requires integration with the wireless communication technology to make the application data with ease available. In this paper, a modified 12 mm x 16 mm x 1.6 mm micro strip patch antenna has been proposed for IoT applications at 2.4 Giga Hertz (GHz) in the Industrial Scientific and Medical (ISM) band. This wideband antenna is designed using Flame Retardant4 (FR4) material as the substrate. The multiband operating characteristics have been achieved by radiating strips to the 50 feed line. Proposed wideband antenna covers frequencies ranging from 1.8 GHz to 3 GHz and 5.3 GHz to 6.9 GHz for -10 dB return loss. The results are analyzed and discuss in term of return loss, Voltage Standing Wave Ratio (VSWR), efficiency and gain. The proposed design has a maximum losses of -31.59 dB at 2.4 GHz and -16.94 dB at 6 GHz. The developed antenna can be useful for several wireless communication applications, such as 2.4 GHz Bluetooth, Wireless Local-Area Network (WLAN) (2.4/5.8 GHz), Worldwide Interoperability for Microwave Access (WiMAX) (5.5 GHz), ISM band and IoT applications.

Smart antenna design for mobile application

Digitalization is becoming more and more important. Building smart houses and industries to offer humans longer lives is one of the main goals of the digitization movement. The main aim of this work is to make those verbal exchange modules more powerful with the aid of either improving the antennas to have a higher layout or changing it with new varieties of antennas that are better able to facilitate powerful verbal exchange. This paper proposes an antenna that can be applied to a verbal exchange module to be able to perform inside the Industrial, Scientific, and Medical (ISM) band at 2.4 GHz. After designing and simulating a complete Printed Circuit Board (PCB) antenna, it found that a few designs produced advanced simulation effects in terms of gain, reflection coefficient, voltage standing wave ratio (VSWR), and band width. Always-pointing antennae are protected by the layout of the antenna, allowing it to protect features inside the Global Positioning System (GPS) and ISM (Industrial, Scientific, and Medical) bands for Wi-Fi devices.

Compact 2*1 Reader Array Antenna Operating in ISM Band for RFID Applications

This paper proposes a compact 2*1 reader array antenna for RFID system having high directivity, good gain, and good reflection coefficient. The structure consists of two main radiating rectangular patch antennas connected in parallel with a common impedance of (50 Ω). These patches are printed on an RT/duroid 5880 substrate possessing a dielectric constant εr equal to 2.2 and 0.0009 as a loss tangent. It operates in ISM (Industrial, Scientific and Medical) band with a resonant frequency of 5.8 GHz. The structure is implemented on a compact size of 38.77× 59.44× 1.6 mm3 equivalent to an electrical size of 0.74λ0× 1.14λ0× 0.03λ0, where λ0 is the free-space wavelength at the resonant frequency. The gain achieved by the final design of the proposed antenna is equal to 9.83 dB, the directivity is around 9.99 dB and the coefficient of reflection (S11) is equal to -49.48 dB. The proposed antenna design is optimized and simulated using Computer Simulation Technology software (CST Microwave Studio).

Developing of Bluetooth mesh flooding between source-destination linking of nodes in wireless sensor networks

Bluetooth uses 2.4 GHz in ISM (industrial, scientific, and medical) band, which it shares with other wireless operating system technologies like ZigBee and WLAN. The Bluetooth core design comprises a low-energy version of a low-rate wireless personal area network and supports point-to-point or point-to-multipoint connections. The aim of the study is to develop a Bluetooth mesh flooding and to estimate packet delivery ratio in wireless sensor networks to model asynchronous transmissions including a visual representation of a mesh network, node-related statistics, and a packet delivery ratio (PDR). This work provides a platform for Bluetooth networking by analyzing the flooding of the network layers and configuring the architecture of a multi-node Bluetooth mesh. Five simulation scenarios have been presented to evaluate the network flooding performance. These scenarios have been performed over an area of 200×200 meters including 81 randomly distributed nodes including different Relay/End node configurations and source-destination linking between nodes. The results indicate that the proposed approach can create a pathway between the source node and destination node within a mesh network of randomly distributed End and Relay nodes using MATLAB environment. The results include probability calculation of getting a linking between two nodes based on Monte Carlo method, which was 88.7428 %, while the Average-hop-count linking between these nodes was 8. Based on the conducted survey, this is the first study to examine and demonstrate Bluetooth mesh flooding and estimate packet delivery ratio in wireless sensor networks

Sensing and analysis of spectrum holes in ISM band using USRP testbed

The spectrum frequency in the wireless communication industry is getting great attention due to the internet of things (IoT) technology's growth. However, the radio spectrum's frequency band use is limited because the primary user for specific services can cause spectrum interference as multiple users use the same spectrum frequency. Meanwhile, at each spectrum frequency, the number of users and utilization time are distinct. These will create vacancies for spectrum frequency assigned to the primary user. A new alternative in using the cognitive radio (CR) spectrum is accessible to these vacancies. This paper analyzed the frequency spectrum in the industrial, scientific and medical (ISM) band and identified spectrum holes for transmission by the secondary users. This work employed a realistic approach by measuring the spectrum using Universal Software Radio Peripheral (USRP) devices. Thus, the spectrum holes in the frequency spectrum had distinguished by using an energy detection technique. In the energy detection technique, the threshold energy level is set and then compared with the energy detector output to identify the primary user's existence (PU). The result indicates that 0.61% of spectrum holes have been detected in the 2.43-2.44 GHz range. This range is sufficient for home appliances, radio frequency peripherals (RF), and bluetooth devices.

Graphene Based Terahertz Antenna Design for Modern Applications

In the Modern communication field, transmitting data through compact antennas like Microstrip patch antennas plays a major role. For Mobile radiolocation, satellite services, medical applications at Terahertz frequency range. Designing antennas for such applications at this frequency must have less weight and good characteristics. For this, graphene is the best suitable material for design due to its electrical, optical, and thermal conductivity properties. So, The Graphene-Based drilled substrate patch antenna 500 X 500 X 40 µm presents the simulation in the terahertz frequency. The prosed antenna structure is well suitable in the ISM (Industrial Scientific and Medical) band 1.36 THz-1.64THz 2.4 ~ 2.5 GHz. Its gives a high gain -20dB. Their Properties have been analyzed with CST for full-wave Simulations.

Study of a printed split-ring monopole for dual-spectrum communications

In this study, we present a low-profile dual-spectrum split-ring monopole that operates at industrial, scientific and medical (ISM) (2.45 GHz) band and ultrawideband (UWB) spectrum (3.1–10.6 GHz). We optimised the design for dual-band operations by using circular split-ring radiators. The coupling between both rings drives the structure to achieve quasi-resonance frequencies in the UWB spectrum. A small stub combines the two radiators and both behave as a single element that enables the antenna to resonate at ISM band 2.45 GHz. The antenna achieves the desired characteristics in terms of good impedance matching, radiation properties as well as other physical and practical requirements such as compact geometry, planar profile and easy fabrication. The very good agreement between the simulated and measured results show that the proposed antenna has the potential for dual-band application.

Embroidered Βow-Tie Wearable Antenna for the 868 and 915 MHz ISM Bands

A textile, embroidered antenna, based on the fractal shape of the Sierpinski triangle, is designed in this paper for operation in the European free Industrial Scientific and Medical (ISM) 863–870 MHz band, as well as in the 902–928 MHz band designated for ISM applications in North and South America. Several prototypes have been fabricated by employing different stitch patterns and thread materials. The effect of the fabrication parameters on the performance of the proposed antenna is investigated through measurements and simulations, with the results being in good agreement. The antenna exhibits attractive characteristics such as wide bandwidth, relatively stable radiation patterns, as well as robustness in washing. Several tests reveal that convex and concave bent conditions do not affect the coverage of the aforementioned ISM bands, despite the shift of the resonant frequency in some cases. Moreover, the SAR values resulting from simulations are below the corresponding thresholds suggested by international guidelines.

MICS/ISM Meander-Line Microstrip Antenna Encapsulated in Oblong-Shaped Pod for Gastrointestinal Tract Diagnosis.

In light of the growth in demand for multiband antennas for medical applications, this research proposes a MICS/ISM meander-line microstrip antenna encapsulated in an oblong-shaped pod for use in diagnoses of the gastrointestinal tract. The proposed antenna is operable in the Medical Implant Communication System (MICS) and the Industrial, Scientific and Medical (ISM) bands. The antenna structure consists of a meander-line radiating patch, a flipped-L defected ground plane, and a loading resistor for antenna miniaturization. The MICS/ISM microstrip antenna encapsulated in an oblong-shaped pod was simulated in various lossy-material environments. In addition, the specific absorption rate (SAR) was calculated and compared against the IEEE C95.1 standard. For verification, an antenna prototype was fabricated and experiments carried out in equivalent liquid mixtures, the dielectric constants of which resembled human tissue. The measured impedance bandwidths (|S11| ≤ −10 dB) for the MICS and ISM bands were 398–407 MHz and 2.41–2.48 GHz. The measured antenna gains were −38 dBi and −13 dBi, with a quasi-omnidirectional radiation pattern. The measured SAR was substantially below the maximum safety limits. As a result, the described MICS/ISM microstrip antenna encapsulated in an oblong-shaped pod can be used for real-time gastrointestinal tract diagnosis. The novelty of this work lies in the use of a meander-line microstrip, flipped-L defected ground plane, and loading resistor to miniaturize the antenna and realize the MICS and ISM bands.

Design and Characterization Analysis of Microstrip Patch Array Antenna with Dumbell shaped DGS for ISM Band Applications

To detect the malignant cancer oust issues in the breast, various techniques are used. These are Mammography ,MRI, and Ultrasound etc. These technologies are miserable during examining. The Microwave Breast Imaging technique generates scattered signals and it detects abnormal tissues after transmission and reception of Microwave signals.Therefore,1X4 array antenna is designed. It detect the tumor at early stage. This array antenna is more specific to detect the malignant issues. The array antenna has 1X4 arrays, with Defected Ground Structure (DGS).It will increase efficiency of this model. This model is used in ISM (Industrial, Scientific, and Medical).It is designed for center frequency2.4GHz. The input return loss should be greater than 10. FR4 is used as Substrate. Theoretical modeling and simulation by HFSS Software is done to optimize antenna parameters. Three antennas namely Microstrip patch antenna, 1 x 4 MSP array antenna and 1 x 4 MSP array antenna with DGS are fabricated and the experimental results are verified in an anechoic chamber of millimeter wave and antenna lab. It is found that the experimental results match the simulated results. It is found that array and DGS enhances the antenna parameters like antenna gain, return loss, VSWR and bandwidth at 2.4GHz frequency for ISM band applications.

Compact radiator antenna: A new approach to enhance the bandwidth using ENG-TL and C-CSRR mushroom meta-resonator

This work presents a new and efficient approach for enhancing the bandwidth and reducing the E-plane cross-polarization (X-pol) of an epsilon negative transmission line (ENG-TL) antenna with reduced size for working in 2.4 GHz Industrial, Scientific and Medical (ISM) band. The antenna consists of ENG-TL on which a curved meander line inductor is loaded for the generation of zeroth-order resonance mode. Subsequently, a miniaturized and low profile (0.06 λ0 × 0.06 λ0 × 0.013 λ0 at 2.44 GHz) circular-complementary split-ring resonator (C-CSRR) based mushroom meta-resonator is stacked over the ENG-TL antenna enhances the bandwidth twice without increasing any additional area. The proposed antenna provides a radiating element size of 0.17λ0 × 0.15λ0 excluding the feedline and total antenna dimension including ground plane is 0.17λ0 × 0.20λ0 × 0.025λ0 at 2.45 GHz. The measured results shows an enhanced impedance bandwidth (IBW) of 7.40%, an acceptable gain of 2.8 dBi, and X-pol value better than 35 dB is obtained for the E-plane. The antenna compactness, extended IBW, low X-pol levels, improved gain, high gain-to-area ratio, and acceptable radiation efficiency indicates that the proposed antenna is appropriate for working in 2.4 GHz (2.4–2.484 GHz) ISM band.

An Approach to Improve the Misalignment and Wireless Power Transfer into Biomedical Implants Using Meandered Wearable Loop Antenna

An approach to improve wireless power transfer (WPT) to implantable medical devices using loop antennas is presented. The antenna exhibits strong magnetic field and dense flux line distribution along two orthogonal axes by insetting the port inside the antenna area. This design shows excellent performance against misalignment in the y-direction and higher WPT as compared with a traditional square loop antenna. Two antennas were optimized based on this approach, one wearable and the other implantable. Both antennas work at both the ISM (Industrial, Scientific, and Medical) band of 433 MHz for WPT and the MedRadio (Medical Device Radiocommunications Service) band of 401–406 MHz for communications. To test the WPT for implantable medical devices, a miniaturized rectifier with a size of 10 mm × 5 mm was designed to integrate with the antenna to form an implantable rectenna. The power delivered to a load of 4.7 kΩ can be up to 1150 μW when 230 mW power is transmitted which is still under the safety limit. This design can be used to directly power a pacemaker, a nerve stimulation device, or a glucose measurement system which requires 70 μW, 100 μW, and 48 μW DC power, respectively.

A multi-band planar antenna for biomedical applications

Abstract We present the design of a compact tri-band adhesive planar antenna which operates as a gateway for biomedical applications. Operating in the Industrial, Scientific and Medical (ISM) band (2.4–2.5 GHz), the Institute of Electrical and Electronics Engineers (IEEE) 802.15.6 Wireless Body Area Network Ultra-Wide Band (WBAN UWB) (3.1–10.6 GHz) and the IEEE 802.11 Wireless Local Area Network or WLAN (WLAN) band (5.15–5.725 GHz), the antenna is useful in the context of body-signal monitoring. The ISM band is used for in-body communication with the implanted medical devices, whereas the WBAN and WLAN bands are for off-body communication with the base station and central medical server, respectively. We have designed our antenna to operate at 2.34/3.20/4.98 GHz. The simulation results show that the antenna has 10 dB bandwidths of 420 MHz (2.07–2.49 GHz), 90 MHz (3.16–3.25 GHz), and 460 MHz (4.76–5.22 GHz) to cover the ISM, WBAN, and WLAN bands, respectively. The proposed antenna is printed on a flexible Rogers RT/duroid 5880 epoxy substrate and it occupies a compact volume of 24 × 24 × 0.787 mm. The designed antenna is simulated using HFSS and the fabricated antenna is experimentally validated by adhering it to a human skin. The simulated and measured performance of the antenna confirms its omnidirectional radiation patterns and high return losses at the three resonant bands.

Dynamic Characterization of a High-Altitude Balloon during a Flight Campaign for the Detection of ISM Radio Background in the Stratosphere

Sounding balloons, available at very low cost from commercial vendors and operable with minimal training, have an excellent potential as testing platforms in the near-space environment. The work reported here was motivated by the need to perform an experimental assessment of the radio frequency (RF) background present in the ISM (Industrial, Scientific and Medical) bands, namely 868 MHz (Ultra High Frequency—UHF) and 2.4 GHz (S-Band), simulating the operational environment of a Low Earth Orbit (LEO) constellation forInternet of Things (IoT) telecommunications. To this end, five balloons were flown with a dedicated RF payload. Along with the radio measurements, the flights provided a convenient opportunity to collect data on the dynamic behavior of the payload gondola. We report on the system design and the operational phase of the mission, and discuss the data collected throughout the successful flight campaign. As a result, a preliminary understanding of the gondola dynamics has been gained, including both linear accelerations and attitude oscillations. It is also concluded that the two ISM bands considered are actually suitable for IoT ground-to-LEO links.

Study of a Printed Split-Ring Monopole for Dual-Spectrum Communications

In this study, we present a low profile dual-spectrum split-ring monopole that operates at industrial, scientific and medical (ISM) (2.45 GHz) band and ultra wideband (UWB) spectrum (3.1-10.6 GHz). We optimized the design for dual- band operations by using circular split-ring radiators. The coupling between both rings drives the structure to achieve quasi-resonance frequencies in the UWB spectrum. A small stub combines the two radiators and both behave as a single element that enables the antenna to resonate at ISM band 2.45 GHz. The antenna achieves the desired characteristics in terms of good impedance matching, radiation properties as well as other physical and practical requirements such as compact geometry, planar profile and easy fabrication. The very good agreement between the simulated and measured results show that the proposed antenna has the potential for dual-band application.

Design and development of Ni0.75Zn0.25Fe2O4/MWCNT microstrip patch antenna (MPA) for ISM band spectrum applications

This research paper represents the design and development of a microstrip patch antenna (MPA) for the ISM (Industrial, Scientific and Medical) band spectrum applications. The main objective of this paper is to analyze the performance of the MPA design using new engineering materials (Ni0.75Zn0.25Fe2O4/MWCNT) synthesized through chemical vapour deposition (CVD) method by utilizing the use of waste cooking oil (WCO) as a carbon source which acts as a printed radiating patch in order to replace a copper or gold (conventional) radiating patch in previous literature. The proposed antenna is fabricated on kapton substrate with dielectric constant, εr = 3.4 and loss tangent, tan δ = 0.004. The conducting patch is Ni0.75Zn0.25Fe2O4/MWCNT and ground antenna material is copper. The results demonstrate that the antenna is capable to comprehend return loss (RL) of – 24.03 dB at frequency of 2.43 GHz with bandwidth of 1.00 GHz and voltage standing wave ratio (VSWR) of 1.14. The antenna has overall dimensions of 33.60 × 41.74 × 0.025 mm3.

Compact wearable dual wideband circularly polarized L-strip fed slotted textile antenna with parasitic elements for ISM band applications

This paper presents an L-strip fed compact wearable dual wide band circularly polarized textile antenna (DWCPTA) with a pair of parasitic elements and dual wide band operations at frequencies 2.45 and 5.80 GHz for industrial, scientific and medical (ISM) band applications. The antenna is printed on top of denim (jeans) substrate having dielectric constant 1.7 and thickness of 1.43 mm with wide slot ground plane on back side. The proposed DWCPTA of size 40 × 40 × 1.43 mm3 achieves -10 dB simulation impedance bandwidth of 89.16% (2.3 – 6.0 GHz) and 3-dB axial ratio bandwidth (ARBW) of 47.55% (2.34 – 3.80 GHz) and 12.60% (5.20 – 5.90 GHz) and essentially, low specific absorption rate (SAR) values of 0.8 and 0.95 W/Kg over 10 g of human tissues for wide band operations at frequencies 2.45 and 5.80 GHz respectively. The proposed DWCPTA is designed, fabricated and tested, which shows good agreement between measured and simulated ones.

Ultra-low-power wideband NMOS LC-VCO design for autonomous connected objects

In this paper, a fully integrated sub threshold LC voltage controlled oscillator (VCO) is presented. A design methodology is also proposed to find the optimal parameters lowering the power consumption. This methodology has been applied to design oscillators for different frequency bands. Furthermore, an adaptive body biasing technique has been used to improve the startup constrains and allows a high immunity to PVT (process, voltage and temperature) variations. A VCO operating in 5 GHz ISM (Industrial, Scientific and Medical) band has been realized with the proposed methodology in 0.13 μm CMOS. It consumes only 468 μW from 0.39 V supply voltage. This makes it possible to meet the required specifications of autonomous connected objects and IoT applications. The measured oscillation frequency can be tuned from 5.14 to 5.44 GHz. The obtained phase noise is approximately equal to − 112 dBc/Hz in post-layout simulation (PLS) and − 104.5 dBc/Hz in measure.

Performance analysis of LoRa in the 2.4 GHz ISM band: coexistence issues with Wi-Fi

Within realization of the visions of the Internet-of-Things (IoT), Low Power Wide Area Networks (LPWANs) are undoubtedly one of the fields that attract high interest from both academic and industrial fields. To ensure reliable data exchange between low power and low data rate devices across long distances, which are the main aims of LPWAs, it is necessary to utilize advanced wireless communication technologies. Emerging LPWA technologies, for instance Long-Range (LoRa) and SigFox, offer many benefits for IoT. These technologies have been primarily developed for sub-GHz frequency bands, but, in the future, their deployment is also considered in the 2.4 GHz industrial, scientific and medical (ISM) bands. However, these unlicensed ISM bands are also used by other technologies for Wireless Local Area Network (WLAN also denoted as Wi-Fi) connectivity and other services, and therefore, coexistence issues can occur here in the future. The main aim of this paper is to perform a performance analysis of the LoRa radio signals interfered by Wi-Fi, using interferers confirming to different IEEE 802.11 family standards, in the 2.4 GHz ISM band. For this purpose, an automated measurement setup and methodology on Physical (PHY) layer are proposed and used. In general, the evaluated results confirm theoretical assumptions on high robustness of LoRa against interferences. However, our results reveal that this robustness of LoRa is highly depending not only on the used LoRa system parameters, but also on the interferer properties and the assumed coexistence scenarios (co-channel, in-band and adjacent channel interferences).

Design and Analysis of Fractal Based Monopole Antenna Backed with Modified Jerusalem Cross Frequency Selective Surface for Wireless Personal Area Communications

This paper presents a low profile Single-layer Modified Jerusalem Cross Frequency Selective Surface (SMJC FSS) which functions as a band-stop filter to shield the 2.45 GHz Industrial, Scientific and Medical (ISM) band with a unit cell size of 0.249λg × 0.249λg × 0.027λg. Compared to JC FSS, 50% size reduction is achieved by the effect of capacitive and inductive loading. The proposed FSS exhibits a fractional bandwidth of 14.69% and fractional bandwidth dimension ratio (FBDR) of 8775.4, which is one of the highest among the single layer FSS. The Koch curve inspired fractal monopole antenna is backed by 5 × 5 FSS array, which contributes enhanced gain and fractional bandwidth of 6.28 dB and 23.75% respectively and has a net dimension of 75 × 75mm ×31.2 mm. The specific absorption rate (SAR) is analyzed on human arm model where proposed antenna attains 0.183 W/Kg, which makes it appropriate for the application of body area communication. The measured results agree well with the simulated results and hence it is validated for wireless personal area communications in the ISM band at 2.45 GHz.