Average Incident Power Research Articles

A Self-Gating RF Energy Harvester for Wireless Power Transfer With High-PAPR Incident Waveform

In this article, we propose a self-gating radio frequency (RF) energy harvester (RFEH) for reaching a high-power harvesting efficiency (PHE) at a low incident RF power level with a high peak-to-average power ratio (high-PAPR) waveform. It includes a power switch between a cross-coupled rectifier and its supplied load to cut off the reverse leakage current in between the short power bursts. The power switch is dynamically controlled based on an indication of the ability of the RFEH to effectively charge the load at the instantaneous incident power level. This is achieved by comparing the load voltage with the open-circuit voltage of a replica rectifier. A comparator with optional proteresis (reversed hysteresis) is proposed for compensating its logic delay at the start and at the end of the short RF power bursts. As a result, the power switch is accurately turned on only during the power bursts. The self-gating RFEH was prototyped for 2.45-GHz wireless power transfer (WPT). It includes a cross-coupled rectifier with the proposed self-gating circuit fabricated in a 65-nm process, a discrete balun, a parasitic-aware-sized π matching network, and an off-the-shelf power management unit (PMU) with maximum power point tracking (MPPT). Measurement results show sensitivity as low as -26.7 dBm with a peak PHE of 32.3% at -14.1-dBm incident power. Compared with the state-of-the-art works, the proposed design significantly improves the RFEH performance at the target low average incident power.

On the Optimal Deployment of Power Beacons for Massive Wireless Energy Transfer

Wireless energy transfer (WET) is emerging as an enabling green technology for Internet of Things (IoT) networks. WET allows the IoT devices to wirelessly recharge their batteries with energy from external sources such as dedicated radio frequency transmitters called power beacons (PBs). In this paper, we investigate the optimal deployment of PBs that guarantees a network-wide energy outage constraint. Optimal positions for the PBs are determined by maximizing the average incident power for the worst location in the service area since no information about the sensor deployment is provided. Such network planning guarantees the fairest harvesting performance for all the IoT devices. Numerical simulations evidence that our proposed optimization framework improves the energy supply reliability compared to benchmark schemes. Additionally, we show that although both, the number of deployed PBs and the number of antennas per PB, introduce performance improvements, the former has a dominant role. Finally, our proposal allows to extend the coverage area while keeping the total power budget fixed, which additionally reduces the level of electromagnetic radiation in the vicinity of PBs.

Supercontinuum generation in tantalum pentoxide waveguides for pump wavelengths in the 900 nm to 1500 nm spectral region.

We characterize the spectral broadening performance in silica clad and unclad Tantalum pentoxide (Ta2O5) waveguides as a function of the input pulse central wavelength and polarization, sweeping over a wavelength range from 900 nm to 1500 nm, with an average incident power of 110 mW. The waveguides are 0.7 µm high and between 2.2 and 3.2 µm wide, and the SiO2 top cladding layer is 2 µm thick. We model the dispersion of the higher order spatial modes, and use numerical simulations based on the generalized nonlinear Schrödinger equation to analyze the nonlinear behaviour of the spatial modes within the waveguides as well as the dispersive effects observed in the experiments. We achieve octave spanning supercontinuum with an average power of 175 mW incident on the waveguide at 1000 nm pump wavelength.

Exposure Assessment in Millimeter‐Wave Reverberation Chamber Using Murine Phantoms

This study deals with the design and calibration of the first mode-stirred reverberation chamber (RC) in the 60-GHz-band adapted for in vivo bioelectromagnetic studies. In addition to the interface for electromagnetic and thermal dosimetry, the interfaces for lighting and ventilation were integrated into the RC walls while preserving acceptable shielding. The RC with mechanical and electronic steering capabilities is characterized in the 55-65 GHz range. To this end, murine skin-equivalent phantoms of realistic shape were designed and fabricated. Their complex permittivity is within ±12% of the target value of murine skin (6.19-j5.81 at 60 GHz). The quality factor of the RC loaded with an animal cage, bedding litter, and five murine phantoms was found to be 1.2 × 104 . The losses inside the RC were analyzed, and it was demonstrated that the main sources of the power dissipation were the phantoms and mice cage. The input power required to reach the average incident power density of 1 and 5 mW/cm2 was found to be 0.23 and 1.14 W, respectively. Surface heating of the mice models was measured in the infrared (IR) range using a specifically designed interface, transparent at IR and opaque at millimeter waves (mmW). Experimental results were compared with an analytical solution of the heat transfer equation and to full-wave computations. Analytical and numerical results were in very good agreement with measurements (the relative deviation after 90 min of exposure was within 4.2%). Finally, a parametric study was performed to assess the impact of the thermophysical parameters on the resulting heating. Bioelectromagnetics. 2020;41:121-135. © 2020 Bioelectromagnetics Society.

A Multi-Band Body-Worn Distributed Radio-Frequency Exposure Meter: Design, On-Body Calibration and Study of Body Morphology

A multi-band Body-Worn Distributed exposure Meter (BWDM) calibrated for simultaneous measurement of the incident power density in 11 telecommunication frequency bands, is proposed. The BDWM consists of 22 textile antennas integrated in a garment and is calibrated on six human subjects in an anechoic chamber to assess its measurement uncertainty in terms of 68% confidence interval of the on-body antenna aperture. It is shown that by using multiple antennas in each frequency band, the uncertainty of the BWDM is 22 dB improved with respect to single nodes on the front and back of the torso and variations are decreased to maximum 8.8 dB. Moreover, deploying single antennas for different body morphologies results in a variation up to 9.3 dB, which is reduced to 3.6 dB using multiple antennas for six subjects with various body mass index values. The designed BWDM, has an improved uncertainty of up to 9.6 dB in comparison to commercially available personal exposure meters calibrated on body. As an application, an average incident power density in the range of 26.7–90.8 μW·m is measured in Ghent, Belgium. The measurements show that commercial personal exposure meters underestimate the actual exposure by a factor of up to 20.6.

Efficient multi-site two-photon functional imaging of neuronal circuits.

Two-photon imaging using high-speed multi-channel detectors is a promising approach for optical recording of cellular membrane dynamics at multiple sites. A main bottleneck of this technique is the limited number of photons captured within a short exposure time (~1ms). Here, we implement temporal gating to improve the two-photon fluorescence yield from holographically projected multiple foci whilst maintaining a biologically safe incident average power. We observed up to 6x improvement in the signal-to-noise ratio (SNR) in Fluorescein and cultured hippocampal neurons showing evoked calcium transients. With improved SNR, we could pave the way to achieving multi-site optical recording of fluorogenic probes with response times in the order of ~1ms.

In vivo setup characterization for pulsed electromagnetic field exposure at 3 GHz

An in vivo setup for pulsed electric field exposure at 3 GHz is proposed and characterized in this work. The exposure system allows far field, whole-body exposure of six animals placed in Plexiglas cages with a circular antenna. Chronic exposures under 18 W incident average power (1–4 kW peak power) and acute exposures under 56 W incident average power (4.7 kW peak power) were considered. Numerical and experimental dosimetry of the setup allowed the accurate calculation of specific absorption rate (SAR) distributions under various exposure conditions. From rat model numerical simulations, the whole-body mean SAR values were 1.3 W kg−1 under chronic exposures and 4.1 W kg−1 under acute exposure. The brain-averaged SAR value was 1.8 W kg−1 and 5.7 W kg−1 under chronic and acute exposure, respectively. Under acute exposure conditions, a 10 g specific absorption of 1.8 ± 1.1 mJ · kg−1 value was obtained. With temperature rises below 0.8 °C, as measured or simulated on a gel phantom under typical in vivo exposures, this exposure system provides adequate conditions for in vivo experimental investigations under non-thermal conditions.

A Personal, Distributed Exposimeter: Procedure for Design, Calibration, Validation, and Application.

This paper describes, for the first time, the procedure for the full design, calibration, uncertainty analysis, and practical application of a personal, distributed exposimeter (PDE) for the detection of personal exposure in the Global System for Mobile Communications (GSM) downlink (DL) band around 900 MHz (GSM 900 DL). The PDE is a sensor that consists of several body-worn antennas. The on-body location of these antennas is investigated using numerical simulations and calibration measurements in an anechoic chamber. The calibration measurements and the simulations result in a design (or on-body setup) of the PDE. This is used for validation measurements and indoor radio frequency (RF) exposure measurements in Ghent, Belgium. The main achievements of this paper are: first, the demonstration, using both measurements and simulations, that a PDE consisting of multiple on-body textile antennas will have a lower measurement uncertainty for personal RF exposure than existing on-body sensors; second, a validation of the PDE, which proves that the device correctly estimates the incident power densities; and third, a demonstration of the usability of the PDE for real exposure assessment measurements. To this aim, the validated PDE is used for indoor measurements in a residential building in Ghent, Belgium, which yield an average incident power density of 0.018 mW/m².

Performance analysis of satellite-to-ground downlink coherent optical communications with spatial diversity over Gamma-Gamma atmospheric turbulence.

The performances of satellite-to-ground downlink optical communications over Gamma-Gamma distributed atmospheric turbulence are studied for a coherent detection receiving system with spatial diversity. Maximum ratio combining (MRC) and selection combining (SC) techniques are considered as practical schemes to mitigate the atmospheric turbulence. Bit-error rate (BER) performances for binary phase-shift keying modulated coherent detection and outage probabilities are analyzed and compared for SC diversity using analytical results and for MRC diversity through an approximation method with different numbers of receiving aperture each with the same aperture area. To show the net diversity gain of a multiple aperture receiver system, BER performances and outage probabilities of MRC and SC multiple aperture receiver systems are compared with a single monolithic aperture with the same total aperture area (same total average incident optical power) for satellite-to-ground downlink optical communications. All the numerical results are verified by Monte-Carlo simulations.

Label-free imaging of thick tissue at 1550 nm using a femtosecond optical parametric generator.

We have developed a simple wavelength-tunable optical parametric generator (OPG), emitting broadband ultrashort pulses with peak wavelengths at 1530-1790 nm, for nonlinear label-free microscopy. The OPG consists of a periodically poled lithium niobate crystal, pumped at 1064 nm by a ultrafast Yb:fiber laser with high pulse energy. We demonstrate that this OPG can be used for label-free imaging, by third-harmonic generation, of nuclei of brain cells and blood vessels in a >150 μm thick brain tissue section, with very little decay of intensity with imaging depth and no visible damage to the tissue at an incident average power of 15 mW.

On-body calibration and measurements using a personal, distributed exposimeter for wireless fidelity.

This paper describes the design, calibration, and measurements with a personal, distributed exposimeter (PDE) for the on-body detection of radio frequency (RF) electromagnetic fields due to Wireless Fidelity (WiFi) networks. Numerical simulations show that using a combination of two RF nodes placed on the front and back of the body reduces the 50% prediction interval (PI50) on the incident free-space electric-field strength (Equation is included in full-text article.). Median reductions of 10 dB and 9.1 dB are obtained compared to the PI50 of a single antenna placed on the body using a weighted arithmetic and geometric average, respectively. Therefore, a simple PDE topology based on two nodes, which are deployed on opposite sides of the human torso, is applied for calibration and measurements. The PDE is constructed using flexible, dual-polarized textile antennas and wearable electronics, which communicate wirelessly with a Universal Serial Bus (USB) connected receiver and can be unobtrusively integrated into a garment. The calibration of the PDE in an anechoic chamber proves that the PI50 of the measured (Equation is included in full-text article.)is reduced to 3.2 dB. To demonstrate the real-life usability of the wireless device, a subject was equipped with the PDE during a walk in the city of Ghent, Belgium. Using a sample frequency of 2 Hz, an average incident power density of 59 nW m was registered in the WiFi frequency band during this walk.

Optically controlled light-pulse propagation in closed-loop configuration with saturable erbium-doped fiber

We report experimental results on the 1550 nm modulated light propagation in a closed-loop all-fiber resonance configuration, which includes a segment of the erbium-doped fiber with saturable optical absorption. It is shown that by a simple increase of the average incident light power, one can switch from the undercoupling to the overcoupling with the closed-loop cavity, which leads to a dramatic change from advancement to delay in the transmitted optical signal with the resonance carrier frequency. In the reported experiments with the ≈4.4 m long closed-loop cavity (with a 2.4 m long EDF segment) we observed a switch from ≈0.26 fractional advancement to ≈0.65 fractional delay in 166 ns periodic light pulses with a resonance frequency in the 1550 nm wavelength range when the average incident power was changed from 0.09 to 0.6 mW.

The Analysis of Implement of SiPM in LDRI System

LDRI system stands for Laser Dynamic Range Imager. It has been used in STS-114 mission in 2005 as the main sensors to realize an on-orbit inspection of the thermal protection system which covers the Orbiter spacecraft. The basic of LDRI is phase discrimination and the key technology is the realization of optoelectronic mixing (OEM) using ICCD. Unfortunately, 2 main drawbacks arise from the usage of ICCD, including the high voltage (~2000V) of PMT drivers and the difficulties in high voltage modulations. SiPM is a rather novel detector which has the similar performances as PMT does but only requires a driving voltage of about 30V. Recently, the SiPM based OEM has been proved and this implies the implement of SiPM in LDRI system. In this paper, the basic of LDRI and SiPM are summerized and some theoretical analysis and simulations are made to verify the feasibility of implement of SiPM in LDRI system. The results show that SiPM is capable of realizing phase discrimination regardless of the high driving voltage and difficulties in modulations. The mean range error is found to be no more than 0.4mm within a range of 5m and an average incident power of 6nW.

Feasibility study of Multi-Pixel Photon Counter serving as the detector in digital optical communications

The feasibility of Multi-Pixel Photon Counter (MPPC) serving as the detector of the receiver in digital optical communication was discussed in this paper. The theory of the sensitivity of the receiver using MPPC was demonstrated. The analytical solution to the minimum average incident light power required was obtained. The numerical analysis results show that the sensitivity is much better than the existing commercial receivers in the same conditions. It may find applications in fields where high sensitivity of optical receiver is a mandatory requirement.

Effect of refractive index mismatch on multi-photon direct laser writing

This work reports how the process of three-dimensional multi-photon direct laser writing (mpDLW) is affected when there is a small mismatch in refractive index between the material being patterned and the medium in which the focusing objective is immersed. Suspended-line microstructures were fabricated by mpDLW in the cross-linkable epoxide SU-8 as a function of focus depth and average incident power. It is found that even a small refractive index contrast of Δn = + 0.08 causes significant variation in feature width and height throughout the depth of the material. In particular, both the width and height of features can either increase or decrease with depth, depending upon how much the average incident laser power exceeds the threshold for writing. Vectorial diffraction theory is used to obtain insight into the origin of the effect and how to compensate for it. We demonstrate that varying the average focused power is a practical means for controlling the variation in feature size with focal depth.

Whole‐genome expression analysis in primary human keratinocyte cell cultures exposed to 60 GHz radiation

The main purpose of this study is to investigate potential responses of skin cells to millimeter wave (MMW) radiation increasingly used in the wireless technologies. Primary human skin cells were exposed for 1, 6, or 24 h to 60.4 GHz with an average incident power density of 1.8 mW/cm(2) and an average specific absorption rate of 42.4 W/kg. A large-scale analysis was performed to determine whether these exposures could affect the gene expression. Gene expression microarrays containing over 41,000 unique human transcript probe sets were used, and data obtained for sham and exposed cells were compared. No significant difference in gene expression was observed when gene expression values were subjected to a stringent statistical analysis such as the Benjamini-Hochberg procedure. However, when a t-test was employed to analyze microarray data, 130 transcripts were found to be potentially modulated after exposure. To further quantitatively analyze these preselected transcripts, real-time PCR was performed on 24 genes with the best combination of high fold change and low P-value. Five of them, namely CRIP2, PLXND1, PTX3, SERPINF1, and TRPV2, were confirmed as differentially expressed after 6 h of exposure. To the best of our knowledge, this is the first large-scale study reporting on potential gene expression modification associated with MMW radiation used in wireless communication applications.

EEG CHANGES AS HEAT STRESS REACTIONS IN RATS IRRADIATED BY HIGH INTENSITY 35 GHz MILLIMETER WAVES

As the application of millimeter waves for civilian and military use increases, the possibility of overexposure to millimeter waves will also increase. This paper attempts to evaluate stress reactions evoked by 35 GHz millimeter waves. The stress reactions in Sprague-Dawley (SD) rats were quantitatively studied by analyzing electroencephalogram (EEG) changes induced by overexposure to 35 GHz millimeter waves. The relative changes in average energy of the EEG and its wavelet decompositions were used for extracting the stress reaction indicators. Incident average power densities (IAPDs) of 35 GHz millimeter waves from 0.5 W cm(-2) to 7.5 W cm(-2) were employed to investigate the relation between irradiation dose and the stress reactions in the rats. Different stress reaction periods evoked by irradiation were quantitatively evaluated by EEG results. The results illustrate that stress reactions are more intense during the first part of the irradiation than during the later part. The skin temperature increase produced by millimeter wave irradiation is the principle reason for stress reactions and skin injuries. As expected, at the higher levels of irradiation, the reaction time decreases and the reaction intensity increases.

Experimental study of the nonlinear hot image effect of broadband pulsed laser beams

The experimental investigation of the nonlinear hot image effect in brand-band pulsed laser beams is reported, placing emphasis on the observation of the formation of hot images and the influence of incident average power of pulse, pulse width, and thickness of the nonlinear medium on the location and intensity of hot images. It is shown that, hot images can be formed from obscurations in the broadband laser beam through a nonlinear Kerr medium slab, as in the case of the monochromatic continious light beam, and are located in the plane symmetrical to the obscuration with respect to the nonlinear slab. In addition, with the incident average power of pulse increasing, the intensity of hot image increases and ultimately reaches saturation, while with the pulse width increasing, the intensity of hot image decreases for a pulse of given energy. On the contrary, it increases for a pulse of given peak power.

Synthesis of Silver Nanoparticles for Remote Opening of Polyelectrolyte Microcapsules

Silver nanoparticles of 10, 18, and 23 nm were synthesized in aqueous medium by chemical reduction of silver nitrate in excess of sodium borohydride. Modification of polyelectrolyte shells with synthesized silver nanoparticles was performed using the layer-by-layer approach. Remote opening of the polyelectrolyte/silver capsules was performed with a CW Nd:YAG FD laser with an average incident power output up to 70 mW. Capsules with a mixture of 10 and 18 nm silver nanoparticles in its polyelectrolyte shell were ruptured after less than 7 s of laser irradiation, while microcapsules with 23 nm silver nanoparticles in the shell were broken after 11 s of laser treatment and 10 nm silver nanoparticles were broken after 26 s.

Carbon Loaded Teflon (CLT): A Power Density meter for Biological Experiments Using Millimeter Waves

The standard technique for measurement of millimeter wave fields utilizes an open-ended waveguide attached to a HP power meter. The alignment of the waveguide with the propagation (K) vector is critical to making accurate measurements. Using this technique, it is difficult and time consuming to make a detailed map of average incident power density over areas of biological interest and the spatial resolution of this instrument does not allow accurate measurements in non-uniform fields. For biological experiments, it is important to know the center field average incident power density and the distribution over the exposed area. Two 4 ft x 4 ft x 1/32 inch sheets of carbon loaded Teflon (CLT) (one 15% carbon and one 25% carbon) were procured and a series of tests to determine the usefulness of CLT in defining fields in the millimeter wavelength range was initiated. Since the CLT was to be used both in the laboratory, where the environment was well controlled, and in the field, where the environment could not be controlled, tests were made to determine effects of change in environmental conditions on ability to use CLT as a millimeter wave dosimeter. The empirical results of this study indicate CLT to be an effective dosimeter for biological experiments both in the laboratory and in the field.